Kiran
Why don't you try by turing off routing ( no ip routing) and just specify a
default-gateway on your 2621. Test the connection again. I have seen this
problem where if you specified a default-gateway plus a default route, most
likely you will not able to access anything outside it subnet.
Tu
""Kiran Kumar M"" wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> On Tue, 24 Jul 2001, Farhan Ahmed wrote:
>
> > WHAT DO u mean by another router with ethernet card
>
> I have 5 Cisco routers with me. Out of that two are in real network, and
> three or spare. I am facing problem with 2620 only, If I replace this
> router with other router, it is not giving any problem..
>
> Kiran
>
>
> > nd unable to ping to other VLANS or outside of that VLAN. If I use
> > > > another router with ethernet card (becuase I am not having another
> > > > ethernet card in first router),
> > -----Original Message-----
> > From: Kiran Kumar M [mailto:[EMAIL PROTECTED]]
> > Sent: Tuesday, July 24, 2001 10:40 PM
> > To: Farhan Ahmed
> > Cc: [EMAIL PROTECTED]
> > Subject: RE: Problem with Fastethernet 2610 router [7:13497]
> >
> >
> >
> > It is not at all the routing problem. Because it is perfectly working
with
> > the same configuration with other router with out any changes.
> >
> > Thanks,
> > Kiran
> > On Tue, 24 Jul 2001, Farhan Ahmed wrote:
> >
> > > u need to setup static route in both direction u just put only 1 route
to
> > > the 1st vlan u need more rotes in both direc
> > > on the other vlans u should have static routes to router via x
> > >
> > > -----Original Message-----
> > > From: Kiran Kumar M [mailto:[EMAIL PROTECTED]]
> > > Sent: Tuesday, July 24, 2001 10:28 PM
> > > To: [EMAIL PROTECTED]
> > > Subject: Re: Problem with Fastethernet 2610 router [7:13497]
> > >
> > >
> > > Thanks for your mail.
> > >
> > > No, the default route is already there. It is already defined in that
> > > router. Infact I just copied it from the working router.
> > >
> > > Thanks,
> > > Kiran
> > >
> > >
> > > On Tue, 24 Jul 2001, Patrick Ramsey wrote:
> > >
> > > > sounds like you have missed a default route on the 2610.
> > > >
> > > > The 2610 will not be able to see any other vlans unless the vlan it
is
> > > plugged into has an ip address assigned to it acting as a "gateway".
> Then
> > > you need to set that ip address as the 2610's default gateway. (or at
> > least
> > > specify a specific route to the other vlans)
> > > >
> > > > If this is a router conencted to the internet, you would defiantely
> want
> > > to keep the default gw out it's serial interface.
> > > >
> > > > -Patrick
> > > >
> > > >
> > > > >>> "Kiran Kumar M" 07/24/01 10:27AM >>>
> > > > Hai,
> > > >
> > > > I am facing a strange problem. I am using a cisco 2610 router in my
> > > > network. In that I am having one fastethernet, and 2 WIC2T . When I
am
> > > > connecting to the L3 switch, it is able to ping to that particular
> VLAN,
> > > > and unable to ping to other VLANS or outside of that VLAN. If I use
> > > > another router with ethernet card (becuase I am not having another
> > > > ethernet card in first router), with the same setup it is able to
> > > > communicate with the outside world. So I concluded that it is not
the
> > > > problem with L3 switch. I tried to find it on cisco site, but unable
to
> > > > locate the solution.
> > > >
> > > > Thanks in advance,
> > > > Kiran
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=13682&t=13497
--------------------------------------------------
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
