Sorry guys, I just got carried away. I always respected Cisco's NDA. I just didn't think that were the real questions since they were so long. In my previous groups I always raised the issue of NDA when some people tried to violate.
IT WILL NOT HAPPEN AGAIN. Regards, Abbas -----Original Message----- From: james mensah [mailto:[EMAIL PROTECTED]] Sent: Tuesday, December 11, 2001 11:32 AM To: Ali, Abbas; [EMAIL PROTECTED] Subject: RE: CCIE written questions [7:28862] Abbas are you new to this group and do you have some respect for Cisco NDA and for that matter ethics? Watch out Cisco is about to get you. -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of Ali, Abbas Sent: Tuesday, December 11, 2001 2:22 PM To: [EMAIL PROTECTED] Subject: RE: CCIE written questions [7:28862] Sorry to hear that. Here is what I think the answers would be. Q1) B Q2) B Q3) Definetly A, could also include B if multiple choice. Q4) AB Q5) Don't know. Q6) BC Q7) Q8) Q9) D Q10) Q11)B -----Original Message----- From: Yang Jun (Ike Yang) [mailto:[EMAIL PROTECTED]] Sent: Tuesday, December 11, 2001 9:50 AM To: [EMAIL PROTECTED] Subject: CCIE written questions [7:28862] Dear CCIEs, I failed in the CCIE written exam today and, I recall some questions here but can't find the correct answer. Do please help me figure out the correct answer and give me your explain. Great thanks! 1.. In a token ring environment, what is allowed regarding early token release? A. More than one token can circulate the ring at any given time, but only one data frame is allowed. B. More than one data frame can circulate the ring at any given time, but only one token is allowed. C. More than one data frame and more than one token can circulate the ring at any given time. D. A station releases a free token after stripping the frame from the ring E. A station can transmit early without waiting for a token to be released from its neighbor. 2. What is the best description of poison reverse? A. It is a procedure used by OSPF to remove a network from the OSPF area. B. Once a connection disappears, the router advertising the bad network will send an update from this network indicating an infinite cost. C. The specific network is not sent out again on the interface it was received on. The network is sent back out on the interface it was received on, but with a metric of one more than the metric in the receive update. 3. In FDD, the characteristics of !04B/5B Encoding!1 include: (multiple answer) A. Sending 4 bits of informations using a 5 bit symbol. B. Increasing the clock rate of the transmitter and receiver to 125Mhz, which establishes an effective data rate of 100Mbps. C. Increasing the distance between two FDDI stations to more than 2km, when using multi-mode fiber. D. Providing a workaround for the optical Bypass Relay. 4. Examine the following: Based on the information above, which OSPF configurations listed are valid? (multiple answer) A. router A router OSPF 1 network 14.0.0.0 0.255.255.255 area 0 router B router OSPF 1 network 14.0.0.0 0.255.255.255 area 0 B. router A router OSPF 1 network 14.1.1.0 0.0.0.255 area 0 router B router OSPF 2 network 14.1.1.0 0.0.0.255 area 0 C. router A router OSPF 1 network 14.0.0.0 0.0.255.255 area 0 router B router OSPF 1 network 14.1.0.0 0.0.0.255 area 0 D. router A router OSPF 1 network 14.1.1.0 0.0.0.255 area 0 router B router OSPF 1 network 14.1.0.0 0.0.255.255 area 0 5. In reorganization, OSPF areas are realigned. Is this a valid network design? If not, what changes could be made to the network and/or router configurations? A. No changes are necessary. B. A virtual link could be configured between Area 60 and area 0. C. A serial line or other physical connections could be installed between devices in Area 60 and Area 0. D. Router B could be configured as an Area Border Router between Area 60 and Area 6. E. This is not valid design, and no changes can make it work. 6. Which of the following CGMP (Cisco group management protocol) statements is correct? A. CGMP manages multicast traffic Catalyst 5000 series switches by allowing directed switching of IP multicast traffic. B. CGMP will switch IP multicast packets to all ports in one specific VLAN. C. CGMP filtering requires a network connection from the Catalyst 5000 series to a router running CGMP. D. CGMP handles ARP, SAP, UDP, SSAP and DSAP. 7. Which statement about RADIUS is true? A. The RADIUS server must you use TCP for its connection the NAS. B. AAA can be configured to direct RADIUS authentication/authorization to one server and RADIUS accounting to a different server. C. RADIUS supports bi-directional CHAP authentication. D. RADIUS is a proprietary protocol that is necessarily vendor specific. E. RADIUS supports command authorization. 8. Which statements about TACACS+ are true? (multiple answer) A. If more than one TACACS+ server is configured and the first one does not respond within a given timeout period, the next TACACS+ server in the list will be contacted. B. The TACACS+ server!/s connection to the NAS encrypts the entire packet. C. The TACACS+ server must use TCP for its connection to the NAS. D. The TACACS+ server must use UDP for its connection to the NAS. E. The TACACS+ server may be configured to use TCP or UDP for its connection to the NAS. 9. CGMP (Cisco Group Management Protocol) is: A. A serial protocol for communications between routers and switches. B. An alternative protocol that can be used instead of SNMP to manage a group of routers/switches. C. A messaging format for routers to download MAC tables to allow layer 2 switching in the router. D. A protocol that provides dynamic configuration, forwarding multicast traffic only to ports that have IP multicast clients attached. 10. Which of the following statements is NOT accurate regarding Frame Relay? A. Frame relay is a high-speed, shared bandwidth Network Layer Protocol. B. Frame relay provides error detection. C. Frame relay does not provide error recovery. D. Frame relay is based on a !0packet-over-circuit!1 architecture. 11. A !.default network!/ performs a service in routing. It is used: A. To generate a default route, independent of the routing protocol implemented in the router. B. To select a candidate route computing the gateway of last resort. C. Only when routing is disabled. D. To override entries in the routing table that use the same class of network address. 12. Examine the following: VERSION 11.2 ! hostname router ! boot system flash slot0:rsp-isv-mz.112-B.P enable password cisco If this router has a configuration-register setting of 0x102, select the proper boot sequence: A. The router will try to use the image !0rsp-isv-mz, 112-8P!1 on slot 0, then attempt to boot from a network server, and finally boot from ROM. B. The router will try use the image !0rsp-isv-mz, 112-8P!1 on slot 0, then attempt to boot from any other valid image in flash, and finally boot from ROM. C. The router will try use the image !0rsp-isv-mz, 112-8P!1 on slot 0, then it will boot from ROM. D. The router will try use the image !0rsp-isv-mz, 112-8P!1 on slot 0, then it will boot from network server. 1.. WAN frame formats generally have which fields in common? A. Flag, address, control, data, FCS B. Source address, destination address, length, data, CRC C. Flag, source address, destination address, control, data, FCS D. Control, data, CRC E. None 13. The configuration for Router A is as follows: RouterA#show running-config Current configuration: Version 11.3 1.) hostname RouterA 2.) enable-password enablepassword 3.) interface Ethernet 0 4.) IP address 191.8.1.1 255.255.255.0 5.) No mop enabled 6.) Interface serial 0 7.) IP address 191.8.150.1 255.255.255.0 8.) IP name-Server 255.255.255.255 9.) IP host RouterB 191.8.150.1 191.8.2.1 10.) Snmp-Server community ccie 11.) Line vty 0 4 12.) Login 13.) Line configure 0\line aux 0 14.) Line vty 0 15.) Password vtypassword 16.) Line vty 1 17.) Password vtypassword 18.) Line vty 2 19.) Password vtypassword 20.) Line vty 3 21.) Password vtypassword 22.) Line vty 4 23.) Password vtypassword 24.) End Router A# The configuration for Router B is as follows: RouterB#show running-config Current Configuration: Version 11.3 1.) hostname RouterB 2.) enable-password san-fran 3.) interface tokenring 0 4.) IP address 191.8.2.1 255.255.255.0 5.) Ring-speed 16 6.) Interface serial 0 7.) IP address 191.8.150.2 255.255.255.0 8.) IP name-Server 255.255.255.255 9.) IP host A 191.8.2.1 191.8.150.1 10.) Snmp-Server community ccie 11.) Logging buffered 12.) Line vty 0 4 13.) Login 14.) Line configure 0 15.) Line aux 0 16.) Line vty 0 17.) Password cisco 18.) Line vty 1 19.) Password cisco 20.) Line vty 2 21.) Password cisco 22.) Line vty 3 23.) Password cisco 24.) Line vty 4 25.) End RouterB# Debug is enabled on Router B, but no debug messages appear on the terminal. Other commands (show commands, etc) seem to be working. What are the probable causes for this? A. Router B is not turned on. B. Debug information is being sent to A. C. The !0terminal monitor!1 command needs to be executed, if this is a virtual terminal session. D. Debug information is being sent to the buffer instead of to the console terminal. E. Debug information is configured at low priority, and will be displayed at a time when the router is less congested. 14. What is the only feature NOT included in FastEther Channel? A. Load balancing B. Full duplex C. Up to 6 interfaces can be bundled into one prot-channel D. Support of HSRP Fault tolerance Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=28890&t=28862 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]