Posting questions from the test that you took is a violation of Cisco's NDA!
----- Original Message ----- From: "Yang Jun (Ike Yang)" To: Sent: Tuesday, December 11, 2001 12:49 Subject: CCIE written questions [7:28862] > Dear CCIEs, > > I failed in the CCIE written exam today and, I recall some questions here > but can't find the correct answer. Do please help me figure out the correct > answer and give me your explain. Great thanks! > > 1.. In a token ring environment, what is allowed regarding early token > release? > > > A. More than one token can circulate the ring at any given > time, but only one data frame is allowed. > > B. More than one data frame can circulate the ring at any > given time, but only one token is allowed. > > C. More than one data frame and more than one token can > circulate the ring at any given time. > > D. A station releases a free token after stripping the frame > from the ring > > E. A station can transmit early without waiting for a token > to be released from its neighbor. > > > > 2. What is the best description of poison reverse? > > > > A. It is a procedure used by OSPF to remove a network from > the OSPF area. > > B. Once a connection disappears, the router advertising the > bad network will send an update from this network indicating an infinite > cost. > > C. The specific network is not sent out again on the > interface it was received on. > > The network is sent back out on the interface it was received on, but with a > metric of one more than the metric in the receive update. > > > > 3. In FDD, the characteristics of !04B/5B Encoding!1 include: (multiple > answer) > > > A. Sending 4 bits of informations using a 5 bit symbol. > > B. Increasing the clock rate of the transmitter and receiver > to 125Mhz, which establishes an effective data rate of 100Mbps. > > C. Increasing the distance between two FDDI stations to more > than 2km, when using multi-mode fiber. > > D. Providing a workaround for the optical Bypass Relay. > > > > 4. Examine the following: > > > > > > > > > > > > > > > > > > > > > > Based on the information above, which OSPF configurations listed are valid? > (multiple answer) > > > > A. router A > > router OSPF 1 > > network 14.0.0.0 0.255.255.255 area 0 > > router B > > router OSPF 1 > > network 14.0.0.0 0.255.255.255 area 0 > > > > B. router A > > router OSPF 1 > > network 14.1.1.0 0.0.0.255 area 0 > > router B > > router OSPF 2 > > network 14.1.1.0 0.0.0.255 area 0 > > > > C. router A > > router OSPF 1 > > network 14.0.0.0 0.0.255.255 area 0 > > router B > > router OSPF 1 > > network 14.1.0.0 0.0.0.255 area 0 > > > > D. router A > > router OSPF 1 > > network 14.1.1.0 0.0.0.255 area 0 > > router B > > router OSPF 1 > > network 14.1.0.0 0.0.255.255 area 0 > > 5. In reorganization, OSPF areas are realigned. Is this a valid network > design? If not, what changes could be made to the network and/or router > configurations? > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > A. No changes are necessary. > > B. A virtual link could be configured between Area 60 and > area 0. > > C. A serial line or other physical connections could be > installed between devices in Area 60 and Area 0. > > D. Router B could be configured as an Area Border Router > between Area 60 and Area 6. > > E. This is not valid design, and no changes can make it > work. > > > > 6. Which of the following CGMP (Cisco group management protocol) > statements is correct? > > > A. CGMP manages multicast traffic Catalyst 5000 series > switches by allowing directed switching of IP multicast traffic. > > B. CGMP will switch IP multicast packets to all ports in one > specific VLAN. > > C. CGMP filtering requires a network connection from the > Catalyst 5000 series to a router running CGMP. > > D. CGMP handles ARP, SAP, UDP, SSAP and DSAP. > > > > 7. Which statement about RADIUS is true? > > > A. The RADIUS server must you use TCP for its connection the > NAS. > > B. AAA can be configured to direct RADIUS > authentication/authorization to one server and RADIUS accounting to a > different server. > > C. RADIUS supports bi-directional CHAP authentication. > > D. RADIUS is a proprietary protocol that is necessarily > vendor specific. > > E. RADIUS supports command authorization. > > > > 8. Which statements about TACACS+ are true? (multiple answer) > > > A. If more than one TACACS+ server is configured and the > first one does not respond within a given timeout period, the next TACACS+ > server in the list will be contacted. > > B. The TACACS+ server!/s connection to the NAS encrypts the > entire packet. > > C. The TACACS+ server must use TCP for its connection to the > NAS. > > D. The TACACS+ server must use UDP for its connection to the > NAS. > > E. The TACACS+ server may be configured to use TCP or UDP > for its connection to the NAS. > > > > 9. CGMP (Cisco Group Management Protocol) is: > > > A. A serial protocol for communications between routers and > switches. > > B. An alternative protocol that can be used instead of SNMP > to manage a group of routers/switches. > > C. A messaging format for routers to download MAC tables to > allow layer 2 switching in the router. > > D. A protocol that provides dynamic configuration, > forwarding multicast traffic only to ports that have IP multicast clients > attached. > > > > 10. Which of the following statements is NOT accurate regarding Frame > Relay? > > > A. Frame relay is a high-speed, shared bandwidth Network > Layer Protocol. > > B. Frame relay provides error detection. > > C. Frame relay does not provide error recovery. > > D. Frame relay is based on a !0packet-over-circuit!1 > architecture. > > > > 11. A !.default network!/ performs a service in routing. It is used: > > > A. To generate a default route, independent of the routing > protocol implemented in the router. > > B. To select a candidate route computing the gateway of last > resort. > > C. Only when routing is disabled. > > D. To override entries in the routing table that use the > same class of network address. > > > > 12. Examine the following: > > > VERSION 11.2 > > ! > > hostname router > > ! > > boot system flash slot0:rsp-isv-mz.112-B.P > > enable password cisco > > > > If this router has a configuration-register setting of 0x102, select the > proper boot sequence: > > > > A. The router will try to use the image !0rsp-isv-mz, > 112-8P!1 on slot 0, then attempt to boot from a network server, and finally > boot from ROM. > > B. The router will try use the image !0rsp-isv-mz, 112-8P!1 > on slot 0, then attempt to boot from any other valid image in flash, and > finally boot from ROM. > > C. The router will try use the image !0rsp-isv-mz, 112-8P!1 > on slot 0, then it will boot from ROM. > > D. The router will try use the image !0rsp-isv-mz, 112-8P!1 > on slot 0, then it will boot from network server. > > 1.. WAN frame formats generally have which fields in common? > > > A. Flag, address, control, data, FCS > > B. Source address, destination address, length, data, CRC > > C. Flag, source address, destination address, control, data, > FCS > > D. Control, data, CRC > > E. None > > > > 13. The configuration for Router A is as follows: > > > > RouterA#show running-config > > Current configuration: > > Version 11.3 > > > > 1.) hostname RouterA > > 2.) enable-password enablepassword > > 3.) interface Ethernet 0 > > 4.) IP address 191.8.1.1 255.255.255.0 > > 5.) No mop enabled > > 6.) Interface serial 0 > > 7.) IP address 191.8.150.1 255.255.255.0 > > 8.) IP name-Server 255.255.255.255 > > 9.) IP host RouterB 191.8.150.1 191.8.2.1 > > 10.) Snmp-Server community ccie > > 11.) Line vty 0 4 > > 12.) Login > > 13.) Line configure 0\line aux 0 > > 14.) Line vty 0 > > 15.) Password vtypassword > > 16.) Line vty 1 > > 17.) Password vtypassword > > 18.) Line vty 2 > > 19.) Password vtypassword > > 20.) Line vty 3 > > 21.) Password vtypassword > > 22.) Line vty 4 > > 23.) Password vtypassword > > 24.) End > > Router A# > > > > The configuration for Router B is as follows: > > > > RouterB#show running-config > > Current Configuration: > > Version 11.3 > > > > 1.) hostname RouterB > > 2.) enable-password san-fran > > 3.) interface tokenring 0 > > 4.) IP address 191.8.2.1 255.255.255.0 > > 5.) Ring-speed 16 > > 6.) Interface serial 0 > > 7.) IP address 191.8.150.2 255.255.255.0 > > 8.) IP name-Server 255.255.255.255 > > 9.) IP host A 191.8.2.1 191.8.150.1 > > 10.) Snmp-Server community ccie > > 11.) Logging buffered > > 12.) Line vty 0 4 > > 13.) Login > > 14.) Line configure 0 > > 15.) Line aux 0 > > 16.) Line vty 0 > > 17.) Password cisco > > 18.) Line vty 1 > > 19.) Password cisco > > 20.) Line vty 2 > > 21.) Password cisco > > 22.) Line vty 3 > > 23.) Password cisco > > 24.) Line vty 4 > > 25.) End > > RouterB# > > > > Debug is enabled on Router B, but no debug messages appear on the terminal. > Other commands (show commands, etc) seem to be working. What are the > probable causes for this? > > > > A. Router B is not turned on. > > B. Debug information is being sent to A. > > C. The !0terminal monitor!1 command needs to be executed, > if this is a virtual terminal session. > > D. Debug information is being sent to the buffer instead > of to the console terminal. > > E. Debug information is configured at low priority, and > will be displayed at a time when the router is less congested. > > > > 14. What is the only feature NOT included in FastEther Channel? > > > A. Load balancing > > B. Full duplex > > C. Up to 6 interfaces can be bundled into one prot-channel > > D. Support of HSRP > > Fault tolerance _________________________________________________________ Do You Yahoo!? Get your free @yahoo.com address at http://mail.yahoo.com Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=28874&t=28862 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]