Hi, what is the IOS feature set used in these two routers? You need a PLUS feature set to support ATM.
With kind regards Jens Neelsen --- Newell Ryan D SrA 18 CS/SCBT wrote: > You said that you got the sample configuration from cisco. Do > you have the > link? > I would like to look at something. My router supports both > 'pvc' and 'atm > pvc'. > But 'pvc' has no vcd and only can operate with qsaal and ilmi. > The 'atm pvc' > does > have a vcd and can support ilmi, qsaal, and all the atm > adaptation layer > protocols. > Something else to look at! > > -----Original Message----- > From: Ken Chipps [mailto:[EMAIL PROTECTED]] > Sent: Thursday, January 16, 2003 5:59 AM > To: [EMAIL PROTECTED] > Subject: RE: Cisco 3640 Router ATM PVC Problem [7:61077] > > > Thanks for the suggestions from everyone. I will check the > software > version tonight. I assumed this was the most recent version as > we > purchased these units only a few months ago, but perhaps not. > > -----Original Message----- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]] On > Behalf Of > Amar > Sent: Wednesday, January 15, 2003 1:59 PM > To: [EMAIL PROTECTED] > Subject: Re: Cisco 3640 Router ATM PVC Problem [7:61077] > > lation_guide_chapter09186a00800e4789.html#xtocid39 > > http://www.cisco.com/en/US/products/sw/iosswrel/ps1835/products_command_ > refe > rence_chapter09186a00800ca7db.html#xtocid5 > > check the above links, they have the info u need. > rgds > > ""Daniel Cotts"" a icrit dans le message de news: > [EMAIL PROTECTED] > > Here's a config from 11.3. Commands have changed quite a > bit. > > Note that clocking must be provided on one end. > > If the cards are single-mode fiber he might have to > attenuate the > signal. > > > > interface ATM6/0 > > description Location > > no ip address > > no ip route-cache optimum > > atm clock INTERNAL > > ! > > interface ATM6/0.1 multipoint (could be point-to-point) > > description pvc to Data Center via XYZ fiber > > ip address aaa.bbb.7.250 255.255.255.252 secondary > > ip address 10.1.19.2 255.255.255.0 > > atm pvc 1 0 35 aal5snap > > map-group TGN > > appletalk cable-range 10119-10119 10119.2 > > appletalk zone ATM > > ! > > > > ! > > map-list TGN > > ip 10.1.19.1 atm-vc 1 broadcast > > ip aaa.bbb.7.249 atm-vc 1 broadcast > > appletalk 10119.1 atm-vc 1 broadcast > > > > > -----Original Message----- > > > From: Newell Ryan D SrA 18 CS/SCBT > [mailto:[EMAIL PROTECTED]] > > > Sent: Wednesday, January 15, 2003 2:58 AM > > > To: [EMAIL PROTECTED] > > > Subject: RE: Cisco 3640 Router ATM PVC Problem [7:61077] > > > > > > > > > I think your right. I know some IOS versions use the 'atm > > > pvc' command. > > > So I agree....what IOS version he is running is a key > > > component to know > > > to resolve this problem. > > > > > > -----Original Message----- > > > From: The Long and Winding Road > > > [mailto:[EMAIL PROTECTED]] > > > Sent: Wednesday, January 15, 2003 4:30 PM > > > To: [EMAIL PROTECTED] > > > Subject: Re: Cisco 3640 Router ATM PVC Problem [7:61077] > > > > > > > > > pvc x/y "should" work, which leads me to wonder about your > > > IOS version. What > > > are you running? what is the image name? > > > > > > I do not see an "atm pvc" command in the 12.1 command > reference. > > > > > > also you mention something about connecting two 3640's > back > > > to back via an > > > OC3 card? I'm not sure you can do that. someone smarter > than > > > I will provide > > > a definitive answer, I'm sure. > > > > > > > > > > > > ""Ken Chipps"" wrote in message > > > [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > > > > I am using a sample configuration from cisco that looks > like this > > > > > > > > First command config t > > > > Second command ip routing > > > > Third command interface atm 1/0 > > > > Fourth command no shutdown > > > > Fifth command ip address 10.0.2.1 255.255.255.0 > > > > Sixth command pvc 1 32 > > > > Seventh command protocol ip 10.0.2.2 broadcast > > > > > > > > The sixth command is where it fails. It does not > recognize the > pvc. > > > > > > > > -----Original Message----- > > > > From: [EMAIL PROTECTED] > [mailto:[EMAIL PROTECTED]] > > > On Behalf Of > > > > Newell Ryan D SrA 18 CS/SCBT > > > > Sent: Tuesday, January 14, 2003 11:32 PM > > > > To: [EMAIL PROTECTED] > > > > Subject: FW: Cisco 3640 Router ATM PVC Problem [7:61077] > > > > > > > > What commands are you typing in? To create a PVC the > syntax is > > > > int atm 1 > > > > atm pvc 6 0 106 aal5snap > > > > I think you are missing the 'atm' before pvc. > > > > > > > > There are several ways to hook the 3640s back to back. > If they are > > > > within > > > > fastethernet distance limitations you could use the > fastethernet > > > > interfaces. > > > > > > > > -----Original Message----- > > > > From: Ken Chipps [mailto:[EMAIL PROTECTED]] > > > > Sent: Wednesday, January 15, 2003 1:40 PM > > > > To: [EMAIL PROTECTED] > > > > Subject: Cisco 3640 Router ATM PVC Problem [7:61077] > > > > > > > > > > > > I am attempting to setup a PVC between two Cisco 3640 > > > Routers connected > > > > back > > > > to back. The interface is an OC3 card. Whenever I issue > the > > > PVC command > > > > on > > > > the ATM interface it says a PVC is not supported. If I > use > > > the ? to see > > > > for > > > > supported commands for the interface, no PVC command is > > > listed. Is there > > > > some software upgrade I need for this? Or is there some > other way > to > > > > conenct > > > > two 3640s back to back? [EMAIL PROTECTED] __________________________________________________ Do you Yahoo!? Yahoo! Mail Plus - Powerful. Affordable. Sign up now. http://mailplus.yahoo.com Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=61144&t=61077 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
