Don, 'could not get a reading' means my multimeter showed 0.L (or infinity), I switched to a large 13.8 volt power supply-now screen reads 13.5v .04 amps...I did some re-soldering again today and now most of the digits on the display light up completely except for the digit above the XIT on plastic display , now my u1 on rf board is not heating up anymore, but there is no 6 volts on it, but the solder connections are good, here are the readings you asked for,
page 22 resistance checks: test point/should read/I read on multimeter (0.L=infinity) p2,pin1, > 10k, 0.L u5 out (5v pin), >2k, 13.89 u4 out (8v pin), 3-7k, 4.40 q1 collector, >1m, 4.39 q2 collector, >1m, 4.39 u3, pin 8, >10k, 1.000 u6, pin 13, >100k, 0.L u6, pin 14,>100k, 0.L u6, pin 29, 70-90k, 95.8 u6, pin 30, 70-90k, 95.8 u8, pin 2, >100k, 0.L u8, pin 15, >100k, 0.L u8, pin 16, >100k, 0.L page 29 resistance checks: test point/should read/I read on multimeter (0.L=infinity) u1, pin 1, 25-35k, 29.2 u1, pin 2, 25-35k, 29.2 u1, pin 3, 40-60k, 47.8 u1, pin 4, >50k, 0>L u1, pin 5, 15-40k, 24.6 u1, pins 6-11, 0, all read 0 u1, pin 12, 9-11k, 9.9 u1, pin 13-40, >50k, all read 0.L j1, pin 1, >1M, 0.L j1, pin 2, > 1M, 0.L j1, pin 3, > 1M, 0.L j1, pin 4, >1M, 0.L j1, pin 5, >1M, 0.L j1, pin 6, >50k, 0.L j1, pin 7, > 1M, 0.L j1, pin 8, 0, 0 j1, pin 9, >50k, 0.L j1, pin 10, >50k 1.009 j1, pin 11, >50k, 0.L j1, pin 12,>50k, .000 j1, pin 13, >50k, 0.L j1, pin 14, >50k, 0.L j1, pin 15, 10-60k, .033 j1, pin 16, 25-35k, .029 j1, pin 17, 25-35k, .029 j1, pin 18, 15-40k, .025 j1, pin 19, 1.5-3.5k, .005 j1, pin 20, 0, 0 page 38 resistance checks: test point/should read/I read on multimeter (0.L=infinity) r115, right end, >500ohms, 4.41 u1, pin 1, >500 ohms, 4.41 u1, pin 4, >20k, 0.L u1, pin 9, >20k, 0.L u1, pin 10, >20k, 0.L u1, pin 28, >20k, 0.L r1 (end near r2), > 1M, 0.L r2 (end near r1), >1M, 0.L 73, KE4QCM Tom Fuller -- View this message in context: http://elecraft.365791.n2.nabble.com/K2-Assembly-problems-Info-080-Message-tp7570609p7570783.html Sent from the Elecraft mailing list archive at Nabble.com. ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html