3M used to make a good high temperature tape that held the thermocouples
nicely. To keep the tape from no allowing the part to radiate the heat
appropriately I used on a small spot of tape over the thermocouple and then a
strong adhesive along the line of the thermocouple leads to "strain relieve"
the thermocouple attachment. Given the general accuracy of type T etc
thermocouples I never ran into a problem. Sure was easier than trying to mix
Fuller's earth and Glassine and was easier on the eyes than rubbing that stuff
into them.
Gary
From: John Allen [mailto:john.al...@era.co.uk]
Sent: Wednesday, April 23, 2003 9:29 AM
To: IEEE EMC/Product Safety (IEEE, EMC/Product Safety)
Subject: RE: Thermocouple glue
Hi Folks
Most of the replies so far seem to indicate the use of "permanent" adhesives
- which means the thermocouples could be difficult to remove and re-use.
Therefore, since these items tend to be too expensive to be considered as
"throw-away" items, does any one have suggestions for adhesives which wil
stick reasonably well but will then allow the thermocouples to be removed
fairly easily and without damage?
Regards
John Allen
ERA Technology Ltd
From: Constantin Bolintineanu [mailto:cbolintine...@dsc.com]
Sent: 22 April 2003 15:22
To: 'Ned Devine'; IEEE EMC/Product Safety (IEEE, EMC/Product Safety)
Subject: RE: Thermocouple glue
I am using LOCTITE 416 - Net wt. 1 OZ.(Part No. 41650) along with the
LOCTITE ACCELERATOR 7452 (Part No. 18637) net. WT.0.70 OZ and works well for
Thermocouples AWG 30. (5-8 seconds)
Respectfully yours,
Constantin
Constantin Bolintineanu P.Eng.
DIGITAL SECURITY CONTROLS LTD.
3301 LANGSTAFF Road, L4K 4L2
CONCORD, ONTARIO, CANADA
e-mail: cbolintine...@dsc.com
Telephone: 905 760 3000 ext 2568
Fax: 905 760 3020
DISCLAIMER: This e-mail message may contain privileged or confidential
information. If you are not the intended recipient, you may not disclose,
use, disseminate, distribute, copy or rely upon this message or attachment
in any way. If you received this e-mail message in error, please return the
message and its attachments to the sender, and then please delete from your
system without copying or forwarding it or call DSC at 905 760 3000
extension 2568 so that the sender's address records can be corrected.
From: Ned Devine [mailto:ndev...@entela.com]
Sent: Wednesday, April 16, 2003 9:11 AM
To: IEEE EMC/Product Safety (IEEE, EMC/Product Safety)
Subject: Thermocouple glue
Hi,
In the past I have used Henkel Sicomet 77 to adhere thermocouples. I
just tried to reorder some and was told it has been discontinued.
Does anyone have a recommendation on a replacement?
Thanks
Ned Devine
Entela, Inc.
3033 Madison Ave. SE
Grand Rapids, MI 49548
Phone: 616 248 9671
Fax: 616 574 9752
e-mail: ndev...@entela.com
www.entela.com
Entela, Inc. A Certified Woman Owned Business
This message is from the IEEE EMC Society Product Safety
Technical Committee emc-pstc discussion list.
Visit our web site at: http://www.ewh.ieee.org/soc/emcs/pstc/
To cancel your subscription, send mail to:
majord...@ieee.org
with the single line:
unsubscribe emc-pstc
For help, send mail to the list administrators:
Ron Pickard: emc-p...@hypercom.com
Dave Heald: davehe...@attbi.com
For policy questions, send mail to:
Richard Nute: ri...@ieee.org
Jim Bacher: j.bac...@ieee.org
Archive is being moved, we will announce when it is back on-line.
All emc-pstc postings are archived and searchable on the web at:
http://www.ieeecommunities.org/emc-pstc
This message is from the IEEE EMC Society Product Safety
Technical Committee emc-pstc discussion list.
Visit our web site at: http://www.ewh.ieee.org/soc/emcs/pstc/
To cancel your subscription, send mail to:
majord...@ieee.org
with the single line:
unsubscribe emc-pstc
For help, send mail to the list administrators:
Ron Pickard: emc-p...@hypercom.com
Dave Heald: davehe...@attbi.com
For policy questions, send mail to:
Richard Nute: ri...@ieee.org
Jim Bacher: j.bac...@ieee.org
Archive is being moved, we will announce when it is back on-line.
All emc-pstc postings are archived and searchable on the web at:
http://www.ieeecommunities.org/emc-pstc
_____________________________________________________________________
This e-mail has been scanned for viruses by the WorldCom Internet Managed
Scanning Service - powered by MessageLabs. For further information visit
http://www.worldcom.com
*************************************************************************
Copyright ERA Technology Ltd. 2003. (www.era.co.uk). All rights reserved.
The information supplied in this Commercial Communication should be treated
in confidence.
No liability whatsoever is accepted for any loss or damage
suffered as a result of accessing this message or any attachments.
_____________________________________________________________________
This e-mail has been scanned for viruses by the WorldCom Internet Managed
Scanning Service - powered by MessageLabs. For further information visit
http://www.worldcom.com
This message is from the IEEE EMC Society Product Safety
Technical Committee emc-pstc discussion list.
Visit our web site at: http://www.ewh.ieee.org/soc/emcs/pstc/
To cancel your subscription, send mail to:
majord...@ieee.org
with the single line:
unsubscribe emc-pstc
For help, send mail to the list administrators:
Ron Pickard: emc-p...@hypercom.com
Dave Heald: davehe...@attbi.com
For policy questions, send mail to:
Richard Nute: ri...@ieee.org
Jim Bacher: j.bac...@ieee.org
Archive is being moved, we will announce when it is back on-line.
All emc-pstc postings are archived and searchable on the web at:
http://www.ieeecommunities.org/emc-pstc
This message is from the IEEE EMC Society Product Safety
Technical Committee emc-pstc discussion list.
Visit our web site at: http://www.ewh.ieee.org/soc/emcs/pstc/
To cancel your subscription, send mail to:
majord...@ieee.org
with the single line:
unsubscribe emc-pstc
For help, send mail to the list administrators:
Ron Pickard: emc-p...@hypercom.com
Dave Heald: davehe...@attbi.com
For policy questions, send mail to:
Richard Nute: ri...@ieee.org
Jim Bacher: j.bac...@ieee.org
Archive is being moved, we will announce when it is back on-line.
All emc-pstc postings are archived and searchable on the web at:
http://www.ieeecommunities.org/emc-pstc
