On Tue, 12 Sep 2017 10:13:26 -0500, Ken Javor <ken.ja...@emccompliance.com> wrote:
> There shouldn't be a lower impedance issue, because from 150 kHz up the LISN > is very close to 50 ohms. And once the LISN coil impedance is well above 50 > ohms, the measured LISN impedance should be 50 ohms in parallel with the > bleeder resistor, which is essentially 50 ohms. The only affect is if there ... I think: o 50 ohms / 50 uH + 5 ohms LISN has impedance spec down to 9 kHz, and its EUT port impedance is 5 ohms + j2.8 ohms at 9 kHz. o Automotive 5 uH LISN has impedance spec down to 150 kHz, and its EUT port impedance is j4.7 ohms at 150 kHz. Regards, Tom -- Tomonori Sato <vef00...@nifty.com> URL: http://t-sato.in.coocan.jp >> From: "T.Sato" <vef00...@nifty.com> >> Reply-To: "T.Sato" <vef00...@nifty.com> >> Date: Tue, 12 Sep 2017 21:58:54 +0900 >> To: <EMC-PSTC@LISTSERV.IEEE.ORG> >> Subject: Re: [PSES] LISN Calibration Measurement Uncertainty >> >> On Mon, 11 Sep 2017 16:32:09 +0000, >> Mac Elliott <00000a115b29e815-dmarc-requ...@ieee.org> wrote: >> >>> We are interested in doing some in-house LISN calibrations (impedance >>> verification only using network analyzer) and need to develop an uncertainty >>> budget. >>> Does anyone happen to have a budget you could share with us? We will go >>> through the exercise of calculating ourself but if there is one out there >>> would appreciate it if you could share. >> >> I think the major contributions would be: >> >> o network analyzer (VNA?); >> o calibration jig which will be required to connect coax to the LISN >> terminals. >> >> Other possible contributions such as resolution and repeatability may also >> need to be considered, even if they are relatively minor. >> >> >> For lower impedance, network analyzers may have relatively large impedance >> measurement uncertainty: >> >> >> http://www.keysight.com/main/editorial.jspx?cc=ES&lc=spa&ckey=1000002148:epsg: >> faq&nid=-11143.0.00&id=1000002148:epsg:faq >> >> Regards, >> Tom >> >> -- >> Tomonori Sato <vef00...@nifty.com> >> URL: http://t-sato.in.coocan.jp >> >> - >> ---------------------------------------------------------------- >> This message is from the IEEE Product Safety Engineering Society emc-pstc >> discussion list. To post a message to the list, send your e-mail to >> <emc-p...@ieee.org> >> >> All emc-pstc postings are archived and searchable on the web at: >> http://www.ieee-pses.org/emc-pstc.html >> >> Attachments are not permitted but the IEEE PSES Online Communities site at >> http://product-compliance.oc.ieee.org/ can be used for graphics (in well-used >> formats), large files, etc. >> >> Website: http://www.ieee-pses.org/ >> Instructions: http://www.ieee-pses.org/list.html (including how to >> unsubscribe) >> List rules: http://www.ieee-pses.org/listrules.html >> >> For help, send mail to the list administrators: >> Scott Douglas <sdoug...@ieee.org> >> Mike Cantwell <mcantw...@ieee.org> >> >> For policy questions, send mail to: >> Jim Bacher: <j.bac...@ieee.org> >> David Heald: <dhe...@gmail.com> > > - > ---------------------------------------------------------------- > This message is from the IEEE Product Safety Engineering Society emc-pstc > discussion list. To post a message to the list, send your e-mail to > <emc-p...@ieee.org> > > All emc-pstc postings are archived and searchable on the web at: > http://www.ieee-pses.org/emc-pstc.html > > Attachments are not permitted but the IEEE PSES Online Communities site at > http://product-compliance.oc.ieee.org/ can be used for graphics (in well-used > formats), large files, etc. > > Website: http://www.ieee-pses.org/ > Instructions: http://www.ieee-pses.org/list.html (including how to > unsubscribe) > List rules: http://www.ieee-pses.org/listrules.html > > For help, send mail to the list administrators: > Scott Douglas <sdoug...@ieee.org> > Mike Cantwell <mcantw...@ieee.org> > > For policy questions, send mail to: > Jim Bacher: <j.bac...@ieee.org> > David Heald: <dhe...@gmail.com> - ---------------------------------------------------------------- This message is from the IEEE Product Safety Engineering Society emc-pstc discussion list. To post a message to the list, send your e-mail to <emc-p...@ieee.org> All emc-pstc postings are archived and searchable on the web at: http://www.ieee-pses.org/emc-pstc.html Attachments are not permitted but the IEEE PSES Online Communities site at http://product-compliance.oc.ieee.org/ can be used for graphics (in well-used formats), large files, etc. Website: http://www.ieee-pses.org/ Instructions: http://www.ieee-pses.org/list.html (including how to unsubscribe) List rules: http://www.ieee-pses.org/listrules.html For help, send mail to the list administrators: Scott Douglas <sdoug...@ieee.org> Mike Cantwell <mcantw...@ieee.org> For policy questions, send mail to: Jim Bacher: <j.bac...@ieee.org> David Heald: <dhe...@gmail.com>