winding a gimbal motor with a 4th axis on a 3d printer. https://www.youtube.com/watch?v=DCKl3B-guSs
cpp program for gcode is available on his website. Rene On 19 Sep 2014, at 19:59, David Armstrong <cncbas...@gmail.com> wrote: > Thanks Ralph, > certianly given me some ideas, and just as i thought not as easy as first > thoughts > > On 19 September 2014 17:59, <p...@wpnet.us> wrote: > >> >> Picture here: >> http://gympiemodelflyers.wordpress.com/articles/brushless-motors/ >> >> ------Original Mail------ >> From: "Dave Caroline" <dave.thearchiv...@gmail.com> >> To: "Enhanced Machine Controller (EMC)" <emc-users@lists.sourceforge.net> >> Sent: Fri, 19 Sep 2014 17:53:53 +0100 >> Subject: Re: [Emc-users] brushless motor coil winder >> >> I do have one relevant picture already though, this shows they are >> wound before placing on the armature and field for tis particular >> design >> >> http://www.collection.archivist.info/archive/Lucas/PS/PA11/ps1636.jpg >> >> Dave >> >> On 19/09/2014, Dave Caroline <dave.thearchiv...@gmail.com> wrote: >>> Thinking of thick wire, I do have some as yet unscanned pictures of >>> (Lucas) starter motor winding machines. >>> >>> Dave Caroline >>> >>> On 19/09/2014, Kirk Wallace <kwall...@wallacecompany.com> wrote: >>>> On 09/19/2014 09:11 AM, Dave Caroline wrote: >>>>> I dont think it is much worse than any other, you just join the groups >>>>> of coils together differently. >>>>> >>>>> Often the coils are wound off the rotor/stator and then mounted and >>>>> varnished to keep steady. >>>>> >>>>> Reverse engineer (unwind) one to see how they did it. >>>>> >>>>> >>>>> Dave Caroline >>>>> >>>>> On 19/09/2014, David Armstrong <cncbas...@gmail.com> wrote: >>>>>> Guys, >>>>>> iv'e been asked to come up with a coil winder for rc brushless motors >>>>>> has anyone done such a winder , specific to rc brushless ,as these are >>>>>> 3 >>>>>> phases >>>>>> i fear it could get complicated >>>>>> >>>>>> Dave >>>> >>>> The RC motors I'm familiar with use a few turns of very thick wire and >>>> would be a bear to wind mechanically. There may be a way to wind a coil >>>> off the core then install it to the stator leg, but this not ideal. >>>> Maybe form C shapes and weld them into a coil after they are installed? >>>> >>>> >>>> -- >>>> Kirk Wallace >>>> http://www.wallacecompany.com/machine_shop/ >>>> http://www.wallacecompany.com/E45/ >>>> >>>> >> ------------------------------------------------------------------------------ >>>> Slashdot TV. Video for Nerds. Stuff that Matters. >>>> >> http://pubads.g.doubleclick.net/gampad/clk?id=160591471&iu=/4140/ostg.clktrk >>>> _______________________________________________ >>>> Emc-users mailing list >>>> Emc-users@lists.sourceforge.net >>>> https://lists.sourceforge.net/lists/listinfo/emc-users >>>> >>> >> >> >> ------------------------------------------------------------------------------ >> Slashdot TV. Video for Nerds. Stuff that Matters. >> >> http://pubads.g.doubleclick.net/gampad/clk?id=160591471&iu=/4140/ostg.clktrk >> _______________________________________________ >> Emc-users mailing list >> Emc-users@lists.sourceforge.net >> https://lists.sourceforge.net/lists/listinfo/emc-users >> >> >> >> ------------------------------------------------------------------------------ >> Slashdot TV. Video for Nerds. Stuff that Matters. >> >> http://pubads.g.doubleclick.net/gampad/clk?id=160591471&iu=/4140/ostg.clktrk >> _______________________________________________ >> Emc-users mailing list >> Emc-users@lists.sourceforge.net >> https://lists.sourceforge.net/lists/listinfo/emc-users >> > ------------------------------------------------------------------------------ > Slashdot TV. Video for Nerds. Stuff that Matters. > http://pubads.g.doubleclick.net/gampad/clk?id=160591471&iu=/4140/ostg.clktrk > _______________________________________________ > Emc-users mailing list > Emc-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/emc-users ------------------------------------------------------------------------------ Slashdot TV. Video for Nerds. Stuff that Matters. http://pubads.g.doubleclick.net/gampad/clk?id=160591471&iu=/4140/ostg.clktrk _______________________________________________ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
