No problem ... but not shure that ubuntu 10.04 can receive the new master .... and these machine for shure I can't upgrade to ubuntu16 or debian 8 ....No one has ever even confirmed the possibility that installing a new JA14 linuxcnc on ubuntu 10.04 can run smoothly.
If you can confirm that: no problem with ubuntu 10.04 + JA14 ... for shure can upgrade. In any case I would like to have some indication to start moving a few steps in the linuxcnc files to test for the momnet, so as to get familiar with the structure of the program .... so have some indication where can see in linuxcnc file for solve these issue.... for me was the first step of these my project. Regards Giorgio ________________________________ Da: Sebastian Kuzminsky <s...@highlab.com> Inviato: sabato 22 aprile 2017 00.45 A: Enhanced Machine Controller (EMC) Oggetto: Re: [Emc-users] halui.max-velocity ... On 04/21/2017 10:21 AM, giorgio foga wrote: > Dear Kuzminsky, > > sorry for the late reply ... no there are JA9 ... the file ini.txt for > observe it .... joint1-2 and axis 1-2 is equal than joint 0 and axis 0 ... > > I see nothings to particular ... so a suggest in witch emc file I try to > observe and study for modify and solve there are a good things..... My advise is still the same: JA9 is very old, and many bugs have been fixed since then. Upgrade your machine to a newer version of the master branch and try again. If the bug is still there we'll try to fix it. > Da: Sebastian Kuzminsky <s...@highlab.com> > Inviato: martedì 11 aprile 2017 20.54 > A: Enhanced Machine Controller (EMC) > Oggetto: Re: [Emc-users] halui.max-velocity ... > > On 04/11/2017 03:10 AM, giorgio foga wrote: >> I just setting the [TRAJ] and [AXIS] and [JOINT] section with the >> right unit per second .... and axis gui work as I aspect ... ... >> everything works well in axis gui, max-value is shown as I expect. >> The problem is only when I want to use the commands >> halui.max-velocity.scale / increase / decrease .... at this point the >> value immediately goes to 60.0 ... and then if I use increase / >> decrease change correctly but never beyond the 60.0 .... at this >> point i try to move the slider axis gui and everything returns to be >> shown properly. I used google translate in hopes of being lighter. >> [😅] .... any how I control again my setting. > > What exact version of LinuxCNC are you using? > > Is this the old ja14 system you mentioned in another thread? If so, and > if an upgrade from ja14 to the current master branch > (v2.8.0-pre1-2975-gc0778d66cf or there abouts) doesn't fix this issue, > please post your ini file somewhere so we can look at it. -- Sebastian Kuzminsky ------------------------------------------------------------------------------ Check out the vibrant tech community on one of the world's most engaging tech sites, Slashdot.org! http://sdm.link/slashdot _______________________________________________ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users Emc-users Info Page - SourceForge<https://lists.sourceforge.net/lists/listinfo/emc-users> lists.sourceforge.net This list is for users of the Enhanced Machine Controller (EMC). Topics include how to obtain, install, configure, and use EMC, as well as other general EMC related ... ------------------------------------------------------------------------------ Check out the vibrant tech community on one of the world's most engaging tech sites, Slashdot.org! http://sdm.link/slashdot _______________________________________________ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
