Hi Peter, we will try of doing the configuration from xilinx in the moment, and we hope to have your help if we have problems. Thank you for the information and we will contact you
El mar., 24 de jul. de 2018 a la(s) 16:31, Peter C. Wallace (p...@mesanet.com) escribió: > On Tue, 24 Jul 2018, yomin estiven jaramillo munera wrote: > > > Date: Tue, 24 Jul 2018 16:18:25 -0500 > > From: yomin estiven jaramillo munera <yejm...@gmail.com> > > Reply-To: "Enhanced Machine Controller (EMC)" > > <emc-users@lists.sourceforge.net> > > To: emc-users@lists.sourceforge.net > > Subject: Re: [Emc-users] parallel ports configuration > > > > the daughter board is made by us, this is not of the firmware recommended > by mesa > > OK so you could give me the pinout, and I can make a compatible bitfile or > you > could download the Xilinx tools and the HostMot2 source and compile one > yourself (you need to make a pinout file that matches your hardware) > > > El mar., 24 de jul. de 2018 a la(s) 16:09, Peter C. Wallace ( > p...@mesanet.com) > escribiяя: > > > On Tue, 24 Jul 2018, yomin estiven jaramillo munera wrote: > > > > > Date: Tue, 24 Jul 2018 16:02:05 -0500 > > > From: yomin estiven jaramillo munera <yejm...@gmail.com> > > > Reply-To: "Enhanced Machine Controller (EMC)" > > > <emc-users@lists.sourceforge.net> > > > To: emc-users@lists.sourceforge.net > > > Subject: Re: [Emc-users] parallel ports configuration > > > > > > Hi, we have observed that we must configurate de firmware from xilinx > is > > this correct?, is there way of doing the configuration of the firmware of > > another way?, is possible do it from pncconf? > > > > > > Firmware is loaded with the utility "mesaflash" that loads bitfiles into > > the > > 5I25s memory > > > > > > The breakout board/daughterboard pinout is needed to determine the proper > > firmware to load. This is why I asked about the breakout board you are > > using. > > > > > > El mar., 24 de jul. de 2018 a la(s) 15:37, yomin estiven jaramillo > munera ( > > yejm...@gmail.com) escribiяяяя: > > > > > Debug file information: > > > ./prueba.hal:51: parameter or pin 'hm2_5i25.0.stepgen.00.dirsetup' not > > > found > > > 6464 > > > PID TTY STAT TIME COMMAND > > > Stopping realtime threads > > > Unloading hal components > > > > > > El mar., 24 de jul. de 2018 a la(s) 15:10, Peter C. Wallace ( > > > p...@mesanet.com) escribiяяяя: > > > > > >> On Tue, 24 Jul 2018, yomin estiven jaramillo munera wrote: > > >> > > >> > Date: Tue, 24 Jul 2018 15:02:31 -0500 > > >> > From: yomin estiven jaramillo munera <yejm...@gmail.com> > > >> > Reply-To: "Enhanced Machine Controller (EMC)" > > >> > <emc-users@lists.sourceforge.net> > > >> > To: emc-users@lists.sourceforge.net > > >> > Subject: Re: [Emc-users] parallel ports configuration > > >> > > > >> > Hi, i have problems for the pc recognize the card 5i25, i am trying > to > > >> >start from pncconf but when i execute linuxcnc, this sends me a error > > >> which > > >> >It seems to be card recognition, I am installing the card and > > immediately > > >> >making the configuration with pncconf, what am i not doing? > > >> > > >> > > >> Can you copy the error message into a email? > > >> > > >> > > >> > > >> Peter Wallace > > >> Mesa Electronics > > >> > > >> > > >> > > >> > > >> > > > ------------------------------------------------------------------------------ > > >> Check out the vibrant tech community on one of the world's most > > >> engaging tech sites, Slashdot.org! http://sdm.link/slashdot > > >> _______________________________________________ > > >> Emc-users mailing list > > >> Emc-users@lists.sourceforge.net > > >> https://lists.sourceforge.net/lists/listinfo/emc-users > > >> > > > > > > > > ------------------------------------------------------------------------------ > > Check out the vibrant tech community on one of the world's most > > engaging tech sites, Slashdot.org! http://sdm.link/slashdot > > _______________________________________________ > > Emc-users mailing list > > Emc-users@lists.sourceforge.net > > https://lists.sourceforge.net/lists/listinfo/emc-users > > > > Peter Wallace > > Mesa Electronics > > > > (\__/) > > (='.'=) This is Bunny. Copy and paste bunny into your > > (")_(") signature to help him gain world domination. > > > > > ------------------------------------------------------------------------------ > > Check out the vibrant tech community on one of the world's most > > engaging tech sites, Slashdot.org! http://sdm.link/slashdot > > _______________________________________________ > > Emc-users mailing list > > Emc-users@lists.sourceforge.net > > https://lists.sourceforge.net/lists/listinfo/emc-users > > > > ------------------------------------------------------------------------------ > Check out the vibrant tech community on one of the world's most > engaging tech sites, Slashdot.org! http://sdm.link/slashdot > _______________________________________________ > Emc-users mailing list > Emc-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/emc-users > > Peter Wallace > Mesa Electronics > > (\__/) > (='.'=) This is Bunny. Copy and paste bunny into your > (")_(") signature to help him gain world domination. > > ------------------------------------------------------------------------------ > Check out the vibrant tech community on one of the world's most > engaging tech sites, Slashdot.org! http://sdm.link/slashdot > _______________________________________________ > Emc-users mailing list > Emc-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/emc-users > ------------------------------------------------------------------------------ Check out the vibrant tech community on one of the world's most engaging tech sites, Slashdot.org! http://sdm.link/slashdot _______________________________________________ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
