On Thursday 26 July 2018 14:34:13 yomin estiven jaramillo munera wrote: > hi, what is the use of the channels ? in the xilenx code appear as > "X00", and when there are stepgen they are in pair as X01 for Y axis > step and X01 for Y dir, this channel can be change in .hal file? > Yes, I'm doing it right now as noise managed to blow some gates in 3 7i90 mesa cards. So I'm using more stepgens than a lathe needs, but the 7i90 has a surplus, so no big deal. And I still have around 20 gpio's I haven't used (yet). And I've got it doing everything but brewing the coffee now. ;-)
> El mar., 24 de jul. de 2018 a la(s) 17:25, yomin estiven jaramillo > munera ( > > [email protected]) escribió: > > Hi Peter, we will try of doing the configuration from xilinx in the > > moment, and we hope to have your help if we have problems. Thank you > > for the information and we will contact you > > > > El mar., 24 de jul. de 2018 a la(s) 16:31, Peter C. Wallace ( > > > > [email protected]) escribió: > >> On Tue, 24 Jul 2018, yomin estiven jaramillo munera wrote: > >> > Date: Tue, 24 Jul 2018 16:18:25 -0500 > >> > From: yomin estiven jaramillo munera <[email protected]> > >> > Reply-To: "Enhanced Machine Controller (EMC)" > >> > <[email protected]> > >> > To: [email protected] > >> > Subject: Re: [Emc-users] parallel ports configuration > >> > > >> > the daughter board is made by us, this is not of the firmware > >> > >> recommended > >> by mesa > >> > >> OK so you could give me the pinout, and I can make a compatible > >> bitfile or you > >> could download the Xilinx tools and the HostMot2 source and compile > >> one yourself (you need to make a pinout file that matches your > >> hardware) > >> > >> > >> El mar., 24 de jul. de 2018 a la(s) 16:09, Peter C. Wallace ( > >> [email protected]) > >> > >> escribiяя: > >> > On Tue, 24 Jul 2018, yomin estiven jaramillo munera wrote: > >> > > Date: Tue, 24 Jul 2018 16:02:05 -0500 > >> > > From: yomin estiven jaramillo munera <[email protected]> > >> > > Reply-To: "Enhanced Machine Controller (EMC)" > >> > > <[email protected]> > >> > > To: [email protected] > >> > > Subject: Re: [Emc-users] parallel ports configuration > >> > > > >> > > Hi, we have observed that we must configurate de firmware from > >> > > xilinx > >> > >> is > >> > >> > this correct?, is there way of doing the configuration of the > >> > firmware > >> > >> of > >> > >> > another way?, is possible do it from pncconf? > >> > > >> > > >> > Firmware is loaded with the utility "mesaflash" that loads > >> > bitfiles into the > >> > 5I25s memory > >> > > >> > > >> > The breakout board/daughterboard pinout is needed to determine > >> > the > >> > >> proper > >> > >> > firmware to load. This is why I asked about the breakout board > >> > you are using. > >> > > >> > > >> > El mar., 24 de jul. de 2018 a la(s) 15:37, yomin estiven > >> > jaramillo > >> > >> munera ( > >> > >> > [email protected]) escribiяяяя: > >> > > Debug file information: > >> > > ./prueba.hal:51: parameter or pin > >> > > 'hm2_5i25.0.stepgen.00.dirsetup' not found > >> > > 6464 > >> > > PID TTY STAT TIME COMMAND > >> > > Stopping realtime threads > >> > > Unloading hal components > >> > > > >> > > El mar., 24 de jul. de 2018 a la(s) 15:10, Peter C. Wallace ( > >> > > > >> > > [email protected]) escribiяяяя: > >> > >> On Tue, 24 Jul 2018, yomin estiven jaramillo munera wrote: > >> > >> > Date: Tue, 24 Jul 2018 15:02:31 -0500 > >> > >> > From: yomin estiven jaramillo munera <[email protected]> > >> > >> > Reply-To: "Enhanced Machine Controller (EMC)" > >> > >> > <[email protected]> > >> > >> > To: [email protected] > >> > >> > Subject: Re: [Emc-users] parallel ports configuration > >> > >> > > >> > >> > Hi, i have problems for the pc recognize the card 5i25, i am > >> > >> trying to > >> > >> > >> >start from pncconf but when i execute linuxcnc, this sends me > >> > >> > a > >> > >> error > >> > >> > >> which > >> > >> > >> > >> >It seems to be card recognition, I am installing the card and > >> > > >> > immediately > >> > > >> > >> >making the configuration with pncconf, what am i not doing? > >> > >> > >> > >> Can you copy the error message into a email? > >> > >> > >> > >> > >> > >> > >> > >> Peter Wallace > >> > >> Mesa Electronics > >> > >> ------------------------------------------------------------------- > >>----------- > >> > >> > >> Check out the vibrant tech community on one of the world's > >> > >> most engaging tech sites, Slashdot.org! > >> > >> http://sdm.link/slashdot > >> > >> _______________________________________________ > >> > >> Emc-users mailing list > >> > >> [email protected] > >> > >> https://lists.sourceforge.net/lists/listinfo/emc-users > >> > >> ------------------------------------------------------------------- > >>----------- > >> > >> > Check out the vibrant tech community on one of the world's most > >> > engaging tech sites, Slashdot.org! http://sdm.link/slashdot > >> > _______________________________________________ > >> > Emc-users mailing list > >> > [email protected] > >> > https://lists.sourceforge.net/lists/listinfo/emc-users > >> > > >> > Peter Wallace > >> > Mesa Electronics > >> > > >> > (\__/) > >> > (='.'=) This is Bunny. Copy and paste bunny into your > >> > (")_(") signature to help him gain world domination. > >> > >> ------------------------------------------------------------------- > >>----------- > >> > >> > Check out the vibrant tech community on one of the world's most > >> > engaging tech sites, Slashdot.org! http://sdm.link/slashdot > >> > _______________________________________________ > >> > Emc-users mailing list > >> > [email protected] > >> > https://lists.sourceforge.net/lists/listinfo/emc-users > >> > >> ------------------------------------------------------------------- > >>----------- Check out the vibrant tech community on one of the > >> world's most engaging tech sites, Slashdot.org! > >> http://sdm.link/slashdot > >> _______________________________________________ > >> Emc-users mailing list > >> [email protected] > >> https://lists.sourceforge.net/lists/listinfo/emc-users > >> > >> Peter Wallace > >> Mesa Electronics > >> > >> (\__/) > >> (='.'=) This is Bunny. Copy and paste bunny into your > >> (")_(") signature to help him gain world domination. > >> > >> ------------------------------------------------------------------- > >>----------- Check out the vibrant tech community on one of the > >> world's most engaging tech sites, Slashdot.org! > >> http://sdm.link/slashdot > >> _______________________________________________ > >> Emc-users mailing list > >> [email protected] > >> https://lists.sourceforge.net/lists/listinfo/emc-users > > ---------------------------------------------------------------------- >-------- Check out the vibrant tech community on one of the world's > most engaging tech sites, Slashdot.org! http://sdm.link/slashdot > _______________________________________________ > Emc-users mailing list > [email protected] > https://lists.sourceforge.net/lists/listinfo/emc-users -- Cheers, Gene Heskett -- "There are four boxes to be used in defense of liberty: soap, ballot, jury, and ammo. Please use in that order." -Ed Howdershelt (Author) Genes Web page <http://geneslinuxbox.net:6309/gene> ------------------------------------------------------------------------------ Check out the vibrant tech community on one of the world's most engaging tech sites, Slashdot.org! http://sdm.link/slashdot _______________________________________________ Emc-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/emc-users
