hi, what is the use of the channels ? in the xilenx code appear as "X00", and when there are stepgen they are in pair as X01 for Y axis step and X01 for Y dir, this channel can be change in .hal file?
El mar., 24 de jul. de 2018 a la(s) 17:25, yomin estiven jaramillo munera ( [email protected]) escribió: > Hi Peter, we will try of doing the configuration from xilinx in the > moment, and we hope to have your help if we have problems. Thank you for > the information and we will contact you > > El mar., 24 de jul. de 2018 a la(s) 16:31, Peter C. Wallace ( > [email protected]) escribió: > >> On Tue, 24 Jul 2018, yomin estiven jaramillo munera wrote: >> >> > Date: Tue, 24 Jul 2018 16:18:25 -0500 >> > From: yomin estiven jaramillo munera <[email protected]> >> > Reply-To: "Enhanced Machine Controller (EMC)" >> > <[email protected]> >> > To: [email protected] >> > Subject: Re: [Emc-users] parallel ports configuration >> > >> > the daughter board is made by us, this is not of the firmware >> recommended >> by mesa >> >> OK so you could give me the pinout, and I can make a compatible bitfile >> or you >> could download the Xilinx tools and the HostMot2 source and compile one >> yourself (you need to make a pinout file that matches your hardware) >> >> >> El mar., 24 de jul. de 2018 a la(s) 16:09, Peter C. Wallace ( >> [email protected]) >> escribiяя: >> >> > On Tue, 24 Jul 2018, yomin estiven jaramillo munera wrote: >> > >> > > Date: Tue, 24 Jul 2018 16:02:05 -0500 >> > > From: yomin estiven jaramillo munera <[email protected]> >> > > Reply-To: "Enhanced Machine Controller (EMC)" >> > > <[email protected]> >> > > To: [email protected] >> > > Subject: Re: [Emc-users] parallel ports configuration >> > > >> > > Hi, we have observed that we must configurate de firmware from xilinx >> is >> > this correct?, is there way of doing the configuration of the firmware >> of >> > another way?, is possible do it from pncconf? >> > >> > >> > Firmware is loaded with the utility "mesaflash" that loads bitfiles into >> > the >> > 5I25s memory >> > >> > >> > The breakout board/daughterboard pinout is needed to determine the >> proper >> > firmware to load. This is why I asked about the breakout board you are >> > using. >> > >> > >> > El mar., 24 de jul. de 2018 a la(s) 15:37, yomin estiven jaramillo >> munera ( >> > [email protected]) escribiяяяя: >> > >> > > Debug file information: >> > > ./prueba.hal:51: parameter or pin 'hm2_5i25.0.stepgen.00.dirsetup' not >> > > found >> > > 6464 >> > > PID TTY STAT TIME COMMAND >> > > Stopping realtime threads >> > > Unloading hal components >> > > >> > > El mar., 24 de jul. de 2018 a la(s) 15:10, Peter C. Wallace ( >> > > [email protected]) escribiяяяя: >> > > >> > >> On Tue, 24 Jul 2018, yomin estiven jaramillo munera wrote: >> > >> >> > >> > Date: Tue, 24 Jul 2018 15:02:31 -0500 >> > >> > From: yomin estiven jaramillo munera <[email protected]> >> > >> > Reply-To: "Enhanced Machine Controller (EMC)" >> > >> > <[email protected]> >> > >> > To: [email protected] >> > >> > Subject: Re: [Emc-users] parallel ports configuration >> > >> > >> > >> > Hi, i have problems for the pc recognize the card 5i25, i am >> trying to >> > >> >start from pncconf but when i execute linuxcnc, this sends me a >> error >> > >> which >> > >> >It seems to be card recognition, I am installing the card and >> > immediately >> > >> >making the configuration with pncconf, what am i not doing? >> > >> >> > >> >> > >> Can you copy the error message into a email? >> > >> >> > >> >> > >> >> > >> Peter Wallace >> > >> Mesa Electronics >> > >> >> > >> >> > >> >> > >> >> > >> >> > >> ------------------------------------------------------------------------------ >> > >> Check out the vibrant tech community on one of the world's most >> > >> engaging tech sites, Slashdot.org! http://sdm.link/slashdot >> > >> _______________________________________________ >> > >> Emc-users mailing list >> > >> [email protected] >> > >> https://lists.sourceforge.net/lists/listinfo/emc-users >> > >> >> > > >> > >> > >> ------------------------------------------------------------------------------ >> > Check out the vibrant tech community on one of the world's most >> > engaging tech sites, Slashdot.org! http://sdm.link/slashdot >> > _______________________________________________ >> > Emc-users mailing list >> > [email protected] >> > https://lists.sourceforge.net/lists/listinfo/emc-users >> > >> > Peter Wallace >> > Mesa Electronics >> > >> > (\__/) >> > (='.'=) This is Bunny. Copy and paste bunny into your >> > (")_(") signature to help him gain world domination. >> > >> > >> ------------------------------------------------------------------------------ >> > Check out the vibrant tech community on one of the world's most >> > engaging tech sites, Slashdot.org! http://sdm.link/slashdot >> > _______________________________________________ >> > Emc-users mailing list >> > [email protected] >> > https://lists.sourceforge.net/lists/listinfo/emc-users >> > >> >> ------------------------------------------------------------------------------ >> Check out the vibrant tech community on one of the world's most >> engaging tech sites, Slashdot.org! http://sdm.link/slashdot >> _______________________________________________ >> Emc-users mailing list >> [email protected] >> https://lists.sourceforge.net/lists/listinfo/emc-users >> >> Peter Wallace >> Mesa Electronics >> >> (\__/) >> (='.'=) This is Bunny. Copy and paste bunny into your >> (")_(") signature to help him gain world domination. >> >> ------------------------------------------------------------------------------ >> Check out the vibrant tech community on one of the world's most >> engaging tech sites, Slashdot.org! http://sdm.link/slashdot >> _______________________________________________ >> Emc-users mailing list >> [email protected] >> https://lists.sourceforge.net/lists/listinfo/emc-users >> > ------------------------------------------------------------------------------ Check out the vibrant tech community on one of the world's most engaging tech sites, Slashdot.org! http://sdm.link/slashdot _______________________________________________ Emc-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/emc-users
