Sweet. http://wiki.x-wrt.org/index.php/Image:Wrp_network-qos.png and http://wiki.x-wrt.org/index.php/Image:Wrp_status-qos.png are screenshots of the clean gui interface for QoS. http://wiki.openwrt.org/TableOfHardware is the supported device page. Very nice use of MoinMoin wiki for project documentation -- project has +++ appearance. :)
tnx! ps - also don't miss ports of openwrt, worth consideration: http://wiki.openwrt.org/CategoryOpenWrtPort?highlight=%28%5ECategory.%2A%29 On Tue, Mar 11, 2008 at 4:20 PM, Michael Miller <[EMAIL PROTECTED]> wrote: > I looked at DD-WRT and it did not have many of the features I was > looking for. I'm currently playing with OpenWRT which I think has a > clearer development cycle / path. If you want more control you might > think about switching to OpenWRT White Russian (Current Stable 0.9 ) > or Kamikaze (Current Dev/Beta 7.09). > > This is a link to the QoSHowto > > http://wiki.openwrt.org/MiniHowtos/QoSHowto > > This is a link to X-Wrt a web interface for OpenWRT > > http://x-wrt.org/ > > -Miller > > > On Tue, Mar 11, 2008 at 2:51 PM, Bob Carlson <[EMAIL PROTECTED]> wrote: > > > > > > > > > > Yes, I'm using DD-WRT and the switch is part of the router. > > > > > > > > I wanted to configure QOS because this is both my and my wife's work > phone > > and there is a lot of stuff happening on the network. I write Wifi > software > > for a living so the networking in the house is, let us say, complicated. > > > > > > > > There are lots of ways to configure the QOS in the DD-WRT, but using the > mac > > address seemed like the most straightforward. Best would be if the PAP2 > was > > setting DSCP properly and the DD-WRT allowed you to configure that. > > Bitorrent is also set up a Bulk. I prefer the classes used by 802.11, > Voice, > > Video, Best Effort and Background. > > > > > > > > I do need to get a UPS or two. > > > > > > > > > > Cheers, Bob > > > > Eugene, OR - Tucson, AZ > > > > > > > > > > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On > Behalf > > Of Ben Barrett > > Sent: Tuesday, March 11, 2008 12:37 PM > > To: Eugene Unix and Gnu/Linux User Group > > Subject: Re: [Eug-lug] WRT54G and WRT54GL routers - anybody had this > > problem? > > > > > > > > > > > > I have not, and also have a Linksys PAP2 from Viatalk connected to my > > Linksys NAT-router -- although I have never seemed to need to fuss with > QoS. > > I also do not have any LAN bridge or other switch, as you do. Is your > > switch a separate device, or are you referring to a multi-port router? > If > > standalone, is it a smart switch or a dummy, or actually a hub? On the > > asterisk wiki there is some documentation about configuring Viatalk, > which > > may be helpful if you haven't seen it, and I think Viatalk has decent > > support pages too (although I haven't needed them, admittedly). > > Oh, you're using DD-WRT instead of the Linksys firmware? If that is > the > > case, then my comparison might not be very helpful... fwiw, I put my > cable > > modem, router, pap2, and phone all on a UPS and can confirm that I still > > have voip service during power outages, which was my goal. Next would > be > > finding a suitable fail-over uplink. :) > > > > Question though: can't you simply configure the QoS to favor your > sip/voip > > traffic rather than the originating address? That way, if you chose to > run > > a soft-phone client you'd still achieve desirable service quality? > > Related question: did you setup QoS b/c of bad call quality, or just > b/c > > you could, or in expectation of silly asymetic uplinks grinding things > to a > > halt, or something else? > > > > ~ben > > > > > > > > > > > > On Tue, Mar 11, 2008 at 12:08 PM, Bob Carlson <[EMAIL PROTECTED]> wrote: > > > > I have a couple of these. One is the main router, the other configured > as a > > bridge to connect my office to the router and cable. At the router I > also > > have a Linksys PAP2 (connected to the switch with an Ethernet cable) > which > > is the IAD for a ViaTalk voip line. > > > > I set up QOS to favor the PAP2 using it's mac address, but I also > assign a > > fixed IP address to the PAP2 in DHCP. > > > > Here's where the problem comes in. Whenever I restart the router for > any > > reason, the PAP2 gets disoriented. It won't work correctly until I > assign a > > different IP address and reboot the router again. It has something to do > > with the PAP2 reregistering with its SIP server. > > > > Has anybody seen this problem? I could track it down, but it would take > a > > long time and lot of equipment shuffling. The DD_WRT sites don't seem to > > have any info on this. > > > > Cheers, Bob > > Eugene, OR - Tucson, AZ > > > > _______________________________________________ > > EUGLUG mailing list > > euglug@euglug.org > > http://www.euglug.org/mailman/listinfo/euglug > > > > > > _______________________________________________ > > EUGLUG mailing list > > euglug@euglug.org > > http://www.euglug.org/mailman/listinfo/euglug > > > > > _______________________________________________ > EUGLUG mailing list > euglug@euglug.org > http://www.euglug.org/mailman/listinfo/euglug >
_______________________________________________ EUGLUG mailing list euglug@euglug.org http://www.euglug.org/mailman/listinfo/euglug
