Hello Steve,

Here are some checks to do before you send the Hairball to Café Electric for 
repair.  See the Café Electric web site for directions and other info.

The following fault conditions I had when first starting up this type of 
motor control using a 5k acceleration potentiometer:

Make sure that the acceleration pedal is release all the way so the 
resistance is below 150 ohms.  Also if the resistance is above 7K ohms will 
cause a fault condition.  One time I could not start up the motor controller 
which was cause by the floor mat laying on the accelerator pedal.

Also there could be a lot of carbon built up on the potentiometer that may 
cause this problem or a high resistance wire connection.

If you have a large main contactor that the contactor coil may surge over 5 
amperes, this will cause the Hairball internal drivers to go into fault or 
even take them out.  It is preferred to install a surge suppression across 
the contactor coils.  I received one from Café Electric when they repair my 
Hairball.  These suppressors are call a Zener Overvoltage Transient 
Suppressors Bidirectional.  For 12 volts, use a 36 volt rated one.

Instead of connecting the Hairball pin# 5 directly to the contactor coil, I 
have it operated a small 12 volt relay to turn on 12 volt power that comes 
from the Ignition On switch.  It is fuse for about 10 amps using a Buss 
Fustron for my large Cable Form contactors. The Fustron or Limitron fuses 
will handle large power surges.

Also make sure that you have main battery voltage present at the input side 
of the main contactor.  If the main battery voltage is not present at this 
contactor, then the contactor will not close.

If you have safety contactors between the main battery and main contactor, 
these safety contactors must come on first from the Ignition On switch 
before the Start switch is activated.

Roland


----- Original Message ----- 
From: "Steve Powers" <[email protected]>
To: <[email protected]>
Sent: Thursday, May 30, 2013 4:47 AM
Subject: [EVDL] Zilla won't come on, no error codes. Please help


> I am trying to help a friend with a conversion that was working fine and
> now Zilla won't pull in the main contactor.  As I understand it, the car
> was fine 9 months ago.  But, it was parked for 9 months.  Main pack still
> checks OK now that he charged it.  It was a lithium pack and stored at a
> low SOC for 9 months.  But, the controller will not come on.
>
> I had a similar issue on my truck when I parked it for several months. 
> All
> I did to get it working was to unhook both 12V and main pack, let sit a 
> few
> minutes, and then rehook.  It started working.  It did take a few tries to
> get it working.  Ultimately, I had an intermittent due to the impact
> sensor.  I bypassed it and the zilla worked great.  I have no idea why his
> doesn't work.
>
> But, he is having issues and I don't know what it could be.  All I do know
> is that both the main pack and 12V were low.  Main pack was probably low
> enough to trip the undervoltage on the Zilla.  12V system is reading
> between 12.5 and 12.6 unloaded.  I think that may be the issue.  I told 
> him
> that the Zilla is picky about its input voltage and he needs 13.2.  That's
> my experience from my truck.  He needs the DC-DC plugged in and working I
> think.  It is currently disconnected.  That's all I could come up with. 
> He
> isn't getting any error codes on the zilla.  It's like it isn't seeing the
> signal to pull in the contactor.  Or, it got scrambled up some how and the
> hairball has lost its mind, highly unlikely.
>
> He wants to know what to try next.  Also, if he can't get it working, 
> where
> can he send the hairball to to have it checked out?  I can't help because
> my truck is sold so I have no way to test the hairball for him.  This is
> really puzzling to me.  I think it is the 12V being too low, but looking
> for your experience with intermittent startup on the zilla.  By the way,
> the car was working and driven 20k miles as an EV, so it is "wired wrong."
>  It just quit from sitting we think.  Nothing is changed in the wiring. 
> He
> did find the DC-DC had an intermittent connection which is why he 
> unplugged
> it.
>
> Steve Powers
> Atlanta
> -------------- next part --------------
> An HTML attachment was scrubbed...
> URL: 
> <http://lists.evdl.org/private.cgi/ev-evdl.org/attachments/20130530/8af3ba66/attachment.htm>
> _______________________________________________
> UNSUBSCRIBE: http://www.evdl.org/help/index.html#usub
> http://lists.evdl.org/listinfo.cgi/ev-evdl.org
> For EV drag racing discussion, please use NEDRA 
> (http://groups.yahoo.com/group/NEDRA)
>
> 
_______________________________________________
UNSUBSCRIBE: http://www.evdl.org/help/index.html#usub
http://lists.evdl.org/listinfo.cgi/ev-evdl.org
For EV drag racing discussion, please use NEDRA 
(http://groups.yahoo.com/group/NEDRA)

Reply via email to