Watch your house and traction voltages at key on and start. I had a lead acid traction pack that showed pack voltage at the contactor but went open as soon as the contactor closed. It was a bad battery that read fine open but went to zero with the slightest load. The Zilla put out some weird errors, I think one was "no start signal".
Also, the contactor drive circuit could be blown out. Is there a diode on the contactor? Good tips above too. On Thu, May 30, 2013 at 8:35 AM, Barry <[email protected]> wrote: > Steve, > > I'll add my two cents based on my experience troubleshooting the Zilla. > Your subject line says the Zilla won't come on. But it also says no error > codes are being thrown. Is the Hairball dead (no lights coming on, no > ability to communicate via serial) or just not closing the contactor (any > lights on the Hairball coming on or ability to communicate with the > Hairball via the serial terminal)? > > My experience is that the Hairball will power up with less than 12V. So I > wouldn't think that is the problem. Now whether your specific contactor > will close on less than 12V is another question. I would start with the > contactor and apply 12V directly to see if it closes. > > Next step would be to see if the Hairball is getting the ignition start > signal. Easy enough to check if 12V is reading on start input (pin 4) and > ignition key/run input (pin 3). As an aside my car has a clutch interlock > switch on the ignition start. If the clutch is not depressed there is not > 12V on the ignition start. Took me "more than a few minutes" when I first > converted my EV to figure out why I was not getting 12V when putting the > ignition into the start position. > > If you can close the contactor manually and the 12V signal is getting to > the Hairball post the results and I'll make a few more suggestions. > > Good luck, > Barry > > > >> Date: Thu, 30 May 2013 06:47:18 -0400 > >> From: [email protected] > >> To: [email protected] > >> Subject: [EVDL] Zilla won't come on, no error codes. Please help > >> > >> I am trying to help a friend with a conversion that was working fine and > >> now Zilla won't pull in the main contactor. As I understand it, the car > >> was fine 9 months ago. But, it was parked for 9 months. Main pack > still > >> checks OK now that he charged it. It was a lithium pack and stored at a > >> low SOC for 9 months. But, the controller will not come on. > >> > >> I had a similar issue on my truck when I parked it for several months. > All > >> I did to get it working was to unhook both 12V and main pack, let sit a > few > >> minutes, and then rehook. It started working. It did take a few tries > to > >> get it working. Ultimately, I had an intermittent due to the impact > >> sensor. I bypassed it and the zilla worked great. I have no idea why > his > >> doesn't work. > >> > >> But, he is having issues and I don't know what it could be. All I do > know > >> is that both the main pack and 12V were low. Main pack was probably low > >> enough to trip the undervoltage on the Zilla. 12V system is reading > >> between 12.5 and 12.6 unloaded. I think that may be the issue. I told > him > >> that the Zilla is picky about its input voltage and he needs 13.2. > That's > >> my experience from my truck. He needs the DC-DC plugged in and working > I > >> think. It is currently disconnected. That's all I could come up with. > He > >> isn't getting any error codes on the zilla. It's like it isn't seeing > the > >> signal to pull in the contactor. Or, it got scrambled up some how and > the > >> hairball has lost its mind, highly unlikely. > >> > >> He wants to know what to try next. Also, if he can't get it working, > where > >> can he send the hairball to to have it checked out? I can't help > because > >> my truck is sold so I have no way to test the hairball for him. This is > >> really puzzling to me. I think it is the 12V being too low, but looking > >> for your experience with intermittent startup on the zilla. By the way, > >> the car was working and driven 20k miles as an EV, so it is "wired > wrong." > >> It just quit from sitting we think. Nothing is changed in the wiring. > He > >> did find the DC-DC had an intermittent connection which is why he > unplugged > >> it. > >> > >> Steve Powers > >> Atlanta > >> -------------- next part -------------- > >> An HTML attachment was scrubbed... > >> URL: < > http://lists.evdl.org/private.cgi/ev-evdl.org/attachments/20130530/8af3ba66/attachment.htm > > > >> _______________________________________________ > >> UNSUBSCRIBE: http://www.evdl.org/help/index.html#usub > >> http://lists.evdl.org/listinfo.cgi/ev-evdl.org > >> For EV drag racing discussion, please use NEDRA ( > http://groups.yahoo.com/group/NEDRA) > >> > > > > -------------- next part -------------- > > An HTML attachment was scrubbed... > > URL: < > http://lists.evdl.org/private.cgi/ev-evdl.org/attachments/20130530/3cacd784/attachment.htm > > > > _______________________________________________ > > UNSUBSCRIBE: http://www.evdl.org/help/index.html#usub > > http://lists.evdl.org/listinfo.cgi/ev-evdl.org > > For EV drag racing discussion, please use NEDRA ( > http://groups.yahoo.com/group/NEDRA) > > > > > _______________________________________________ > UNSUBSCRIBE: http://www.evdl.org/help/index.html#usub > http://lists.evdl.org/listinfo.cgi/ev-evdl.org > For EV drag racing discussion, please use NEDRA ( > http://groups.yahoo.com/group/NEDRA) > > -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.evdl.org/private.cgi/ev-evdl.org/attachments/20130530/afe7a075/attachment.htm> _______________________________________________ UNSUBSCRIBE: http://www.evdl.org/help/index.html#usub http://lists.evdl.org/listinfo.cgi/ev-evdl.org For EV drag racing discussion, please use NEDRA (http://groups.yahoo.com/group/NEDRA)
