Jim, >From what you are telling I would suspect the firewall kernel not to be bound to all of the interfaces. I am not sure how you could check that in solaris though, but I bet a number of the common Internet sites will.
Jeroen. -----Oorspronkelijk bericht----- Van: Mailing list for discussion of Firewall-1 [mailto:[EMAIL PROTECTED] Namens James Edwards Gepost om: donderdag 12 februari 2004 14:56 Gepost naar: Security Discussie: [FW-1] Secure Remote, what am I missing Onderwerp: Re: [FW-1] Secure Remote, what am I missing Before I ever even started testing or installed Secure Remote, I broke the PC off the local LAN and used a dial-up from outside my network so that has been consistent throughout my testing. I've been watching Tracker but it doesn't give me any clue as to what is wrong or why things are doing what they are doing. Is there something specific I should be looking for? Jim E -----Original Message----- From: Ray Pesek [mailto:[EMAIL PROTECTED] Sent: Wednesday, February 11, 2004 4:18 PM To: [EMAIL PROTECTED] Subject: Re: [FW-1] Secure Remote, what am I missing If you're switching between a LAN NIC and SR without rebooting, or dial-up & LAN, etc., the routing table on the computer is probably the culprit. They get confused when you do stuff like that because they think the old route is still available. Does SmartView Tracker show anything? Ray Pesek, CISSP >From: James Edwards <[EMAIL PROTECTED]> >Reply-To: Mailing list for discussion of Firewall-1 ><[EMAIL PROTECTED]> >To: [EMAIL PROTECTED] >Subject: [FW-1] Secure Remote, what am I missing >Date: Wed, 11 Feb 2004 13:30:59 -0600 > >I apologize in advance for the relatively general nature of this >question but I am having some real problems getting Secure Remote to work correctly. > >I'm using NG with AI R55 on a Solaris 9 machine. > >I got Secure Remote installed on a client and got it to recognize the >gateway and I got in with my login and password just fine after having >set up the few options available in the default Remote Access community. >However, when I connect to the various resources, the results I get are >very strange. Sometimes it encrypts and sometimes it doesn't. >Sometimes it lets me in and sometimes it doesn't. The results do seem >to be consistent on a per machine basis (if I can get in I can always >get in and vice versa) but nothing I do in the rule base seems to >change any of the behavior. > >I've got a lot more study and research to do on this but if anyone can >offer some general tips or a link to some good documentation, it would >be most appreciated. > >Jim Edwards >Systems Manager >Texas Secretary of State > >================================================= >To set vacation, Out-Of-Office, or away messages, send an email to >[EMAIL PROTECTED] >in the BODY of the email add: >set fw-1-mailinglist nomail >================================================= >To unsubscribe from this mailing list, >please see the instructions at >http://www.checkpoint.com/services/mailing.html >================================================= >If you have any questions on how to change your subscription options, >email [EMAIL PROTECTED] >================================================= _________________________________________________________________ Keep up with high-tech trends here at "Hook'd on Technology." http://special.msn.com/msnbc/hookedontech.armx ================================================= To set vacation, Out-Of-Office, or away messages, send an email to [EMAIL PROTECTED] in the BODY of the email add: set fw-1-mailinglist nomail ================================================= To unsubscribe from this mailing list, please see the instructions at http://www.checkpoint.com/services/mailing.html ================================================= If you have any questions on how to change your subscription options, email [EMAIL PROTECTED] ================================================= ================================================= To set vacation, Out-Of-Office, or away messages, send an email to [EMAIL PROTECTED] in the BODY of the email add: set fw-1-mailinglist nomail ================================================= To unsubscribe from this mailing list, please see the instructions at http://www.checkpoint.com/services/mailing.html ================================================= If you have any questions on how to change your subscription options, email [EMAIL PROTECTED] ================================================= ================================================= To set vacation, Out-Of-Office, or away messages, send an email to [EMAIL PROTECTED] in the BODY of the email add: set fw-1-mailinglist nomail ================================================= To unsubscribe from this mailing list, please see the instructions at http://www.checkpoint.com/services/mailing.html ================================================= If you have any questions on how to change your subscription options, email [EMAIL PROTECTED] =================================================
