Right,
You would redefine it like this
define vswitch lnxvsw1 rdev 9004.p01
Or play it safe and put both in there ☺
define vswitch lnxvsw1 rdev 9004.p00 9004.p01
Marcy
This message may contain confidential and/or privileged information. If you are
not the addressee or authorized to receive this for the addressee, you must not
use, copy, disclose, or take any action based on this message or any
information herein. If you have received this message in error, please advise
the sender immediately by reply e-mail and delete this message. Thank you for
your cooperation.
From: The IBM z/VM Operating System [mailto:IBMVM@LISTSERV.UARK.EDU] On Behalf
Of George Henke/NYLIC
Sent: Friday, February 04, 2011 1:53 PM
To: IBMVM@LISTSERV.UARK.EDU
Subject: Re: [IBMVM] z196 lb4ul
Paul, Marcy, et al:
I just came from a z196 pre-install planning meeting (by phone) in which it was
said that the OSA on the z/196 will be using PORT 1.
We are currently using PORT 0 on our Z9.
Does this mean our VSWITCH definition (below) in SYSTEM CONFIG which defaults
to PORT 0 will not work on the z196 unless we code PORT 1?
define vswitch lnxvsw1 rdev 9004
George Henke/NYLIC
02/01/2011 03:40 PM
To
The IBM z/VM Operating System <IBMVM@LISTSERV.UARK.EDU>
cc
Subject
Re: z196 lb4ulLink
ty all very much.
"Feller, Paul" <pfel...@aegonusa.com>
Sent by: The IBM z/VM Operating System <IBMVM@LISTSERV.UARK.EDU>
02/01/2011 03:24 PM
Please respond to
The IBM z/VM Operating System <IBMVM@LISTSERV.UARK.EDU>
To
IBMVM@LISTSERV.UARK.EDU
cc
Subject
Re: z196 lb4ul
You would be using the default which is port 0 (zero). The port number really
only comes into play if you have an OSA Express3 card and are connecting to the
second port or what is called the A1 port on the card layout.
Paul Feller
AIT Mainframe Technical Support
From: The IBM z/VM Operating System [mailto:IBMVM@LISTSERV.UARK.EDU] On Behalf
Of George Henke/NYLIC
Sent: Tuesday, February 01, 2011 2:05 PM
To: IBMVM@LISTSERV.UARK.EDU
Subject: Re: z196 lb4ul
What is the default PORT number?
We do not specify PORT number in our VSWITCH definition below (from SYSTEM
CONFIG):
define vswitch lnxvsw1 rdev 9004
Sorry to ask:
But does this mean we do not use an OSA.?
Or does it mean we use a default?
I think it may mean the former.
Mark Post <mp...@novell.com>
Sent by: The IBM z/VM Operating System <IBMVM@LISTSERV.UARK.EDU>
02/01/2011 02:50 PM
Please respond to
The IBM z/VM Operating System <IBMVM@LISTSERV.UARK.EDU>
To
IBMVM@LISTSERV.UARK.EDU
cc
Subject
Re: z196 lb4ul
>>> On 2/1/2011 at 02:45 PM, George Henke/NYLIC <george_he...@newyorklife.com>
wrote:
> How did you change your vswitch definition for PO1?
>
> Chuckie has deigned use of PORTNAME in VSWITCH taboo.
Port number is not the same as port name. Two different parameters entirely.
Mark Post
