Does this mean something fatal has happend to this card? The card had been working for well over a year now. After moving from FC5 ivtv v7.2 to FC6 ivtv v8.2 I am getting errors. The PVR500 card in this system loads find. The other system that I have with a PVR-350 now running FC6 ivtv v8.2 works fine.
Thanks, Rich ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.8.2 (tagged release) loading ivtv: Linux version: 2.6.18-1.2849.fc6 SMP mod_unload gcc-4.1 ivtv: In case of problems please include the debug info between ivtv: the START INIT IVTV and END INIT IVTV lines, along with ivtv: any module options, when mailing the ivtv-users mailinglist. sd 0:0:0:0: Attached scsi generic sg0 type 0 sd 1:0:0:0: Attached scsi generic sg1 type 0 eth1: forcedeth.c: subsystem: 01462:0300 bound to 0000:00:05.0 ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 21 ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [APCJ] -> GSI 21 (level, high) -> IRQ 193 PCI: Setting latency timer of device 0000:00:06.0 to 64 intel8x0_measure_ac97_clock: measured 51586 usecs intel8x0: clocking to 46867 ivtv0: Autodetected Hauppauge card (cx23415 based) i2c_adapter i2c-0: nForce2 SMBus adapter at 0x4c00 i2c_adapter i2c-1: nForce2 SMBus adapter at 0x4c40 ACPI: PCI Interrupt 0000:02:07.0[A] -> Link [APC2] -> GSI 17 (level, low) -> IRQ 209 ivtv0: Unreasonably low latency timer, setting to 64 (was 32) ieee1394: Host added: ID:BUS[0-00:1023] GUID[0010dc00006baf5b] ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) ivtv0: loaded v4l-cx2341x-dec.fw firmware (262144 bytes) tveeprom 2-0050: Huh, no eeprom present (err=-121)? tveeprom 2-0050: Encountered bad packet header [01]. Corrupt or not a Hauppauge eeprom. ivtv0: Invalid EEPROM ivtv0: Encoder revision: 0x02050032 ivtv0: Decoder revision: 0x02020023 ivtv0: Registered device video0 for encoder MPEG ivtv0: Registered device video32 for encoder YUV ivtv0: Registered device vbi0 for encoder VBI ivtv0: Registered device video24 for encoder PCM audio ivtv0: Registered device radio0 for encoder radio ivtv0: Registered device video16 for decoder MPEG ivtv0: Registered device vbi8 for decoder VBI ivtv0: Registered device vbi16 for decoder VOUT ivtv0: Registered device video48 for decoder YUV ivtv0: loaded v4l-cx2341x-init.mpg firmware (155648 bytes) ivtv0: i2c hardware 0x00000008 (msp3400) not found for command 0xc008561c! ivtv0: i2c addr 0x21 not found for command 0x4008646f! ivtv0: i2c hardware 0x00000008 (msp3400) not found for command 0x4008646d! ivtv0: i2c hardware 0x00000008 (msp3400) not found for command 0xc008561c! ivtv0: i2c hardware 0x00000008 (msp3400) not found for command 0xc008561c! ivtv0: i2c hardware 0x00000008 (msp3400) not found for command 0xc008561c! ivtv0: Initialized Hauppauge WinTV PVR-350, card #0 ivtv: ====================== NEXT CARD ====================== _______________________________________________ ivtv-devel mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-devel
