Thanks Dirk, that worked. Note for others: newi2c=1 not i2cnew=false Rich
> I had a similar problem, try to set a module paramter "i2cnew=false" > because > also with my card the I2C code doesn't work! > > > Am Donnerstag, 14. Dezember 2006 17:36 schrieb Rich: >> Does this mean something fatal has happend to this card? >> >> The card had been working for well over a year now. After moving from >> FC5 >> ivtv v7.2 to FC6 ivtv v8.2 I am getting errors. The PVR500 card in this >> system loads find. The other system that I have with a PVR-350 now >> running FC6 ivtv v8.2 works fine. >> >> Thanks, >> Rich >> >> ivtv: ==================== START INIT IVTV ==================== >> ivtv: version 0.8.2 (tagged release) loading >> ivtv: Linux version: 2.6.18-1.2849.fc6 SMP mod_unload gcc-4.1 >> ivtv: In case of problems please include the debug info between >> ivtv: the START INIT IVTV and END INIT IVTV lines, along with >> ivtv: any module options, when mailing the ivtv-users mailinglist. >> sd 0:0:0:0: Attached scsi generic sg0 type 0 >> sd 1:0:0:0: Attached scsi generic sg1 type 0 >> eth1: forcedeth.c: subsystem: 01462:0300 bound to 0000:00:05.0 >> ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 21 >> ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [APCJ] -> GSI 21 (level, >> high) >> -> IRQ 193 >> PCI: Setting latency timer of device 0000:00:06.0 to 64 >> intel8x0_measure_ac97_clock: measured 51586 usecs >> intel8x0: clocking to 46867 >> ivtv0: Autodetected Hauppauge card (cx23415 based) >> i2c_adapter i2c-0: nForce2 SMBus adapter at 0x4c00 >> i2c_adapter i2c-1: nForce2 SMBus adapter at 0x4c40 >> ACPI: PCI Interrupt 0000:02:07.0[A] -> Link [APC2] -> GSI 17 (level, >> low) >> -> IRQ 209 >> ivtv0: Unreasonably low latency timer, setting to 64 (was 32) >> ieee1394: Host added: ID:BUS[0-00:1023] GUID[0010dc00006baf5b] >> ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) >> ivtv0: loaded v4l-cx2341x-dec.fw firmware (262144 bytes) >> tveeprom 2-0050: Huh, no eeprom present (err=-121)? >> tveeprom 2-0050: Encountered bad packet header [01]. Corrupt or not a >> Hauppauge eeprom. >> ivtv0: Invalid EEPROM >> ivtv0: Encoder revision: 0x02050032 >> ivtv0: Decoder revision: 0x02020023 >> ivtv0: Registered device video0 for encoder MPEG >> ivtv0: Registered device video32 for encoder YUV >> ivtv0: Registered device vbi0 for encoder VBI >> ivtv0: Registered device video24 for encoder PCM audio >> ivtv0: Registered device radio0 for encoder radio >> ivtv0: Registered device video16 for decoder MPEG >> ivtv0: Registered device vbi8 for decoder VBI >> ivtv0: Registered device vbi16 for decoder VOUT >> ivtv0: Registered device video48 for decoder YUV >> ivtv0: loaded v4l-cx2341x-init.mpg firmware (155648 bytes) >> ivtv0: i2c hardware 0x00000008 (msp3400) not found for command >> 0xc008561c! >> ivtv0: i2c addr 0x21 not found for command 0x4008646f! >> ivtv0: i2c hardware 0x00000008 (msp3400) not found for command >> 0x4008646d! >> ivtv0: i2c hardware 0x00000008 (msp3400) not found for command >> 0xc008561c! >> ivtv0: i2c hardware 0x00000008 (msp3400) not found for command >> 0xc008561c! >> ivtv0: i2c hardware 0x00000008 (msp3400) not found for command >> 0xc008561c! >> ivtv0: Initialized Hauppauge WinTV PVR-350, card #0 >> ivtv: ====================== NEXT CARD ====================== >> >> >> _______________________________________________ >> ivtv-devel mailing list >> [email protected] >> http://ivtvdriver.org/mailman/listinfo/ivtv-devel > > _______________________________________________ > ivtv-devel mailing list > [email protected] > http://ivtvdriver.org/mailman/listinfo/ivtv-devel > _______________________________________________ ivtv-devel mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-devel
