Rich wrote: > Thanks Dirk, that worked. > Note for others: newi2c=1 not i2cnew=false >
You specifically enable newi2c while Dirk turns it off. newi2c:Use new I2C implementation -1 is autodetect, 0 is off, 1 is on I have created a new entry in the troubleshooting page on the wiki. Greets Sander PS: It is better to ask the ivtv-user list instead of the ivtv-devel list with these questions, Thanks :-) > Rich > >> I had a similar problem, try to set a module paramter "i2cnew=false" >> because >> also with my card the I2C code doesn't work! >> >> >> Am Donnerstag, 14. Dezember 2006 17:36 schrieb Rich: >>> Does this mean something fatal has happend to this card? >>> >>> The card had been working for well over a year now. After moving from >>> FC5 >>> ivtv v7.2 to FC6 ivtv v8.2 I am getting errors. The PVR500 card in this >>> system loads find. The other system that I have with a PVR-350 now >>> running FC6 ivtv v8.2 works fine. >>> >>> Thanks, >>> Rich >>> >>> ivtv: ==================== START INIT IVTV ==================== >>> ivtv: version 0.8.2 (tagged release) loading >>> ivtv: Linux version: 2.6.18-1.2849.fc6 SMP mod_unload gcc-4.1 >>> ivtv: In case of problems please include the debug info between >>> ivtv: the START INIT IVTV and END INIT IVTV lines, along with >>> ivtv: any module options, when mailing the ivtv-users mailinglist. >>> sd 0:0:0:0: Attached scsi generic sg0 type 0 >>> sd 1:0:0:0: Attached scsi generic sg1 type 0 >>> eth1: forcedeth.c: subsystem: 01462:0300 bound to 0000:00:05.0 >>> ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 21 >>> ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [APCJ] -> GSI 21 (level, >>> high) >>> -> IRQ 193 >>> PCI: Setting latency timer of device 0000:00:06.0 to 64 >>> intel8x0_measure_ac97_clock: measured 51586 usecs >>> intel8x0: clocking to 46867 >>> ivtv0: Autodetected Hauppauge card (cx23415 based) >>> i2c_adapter i2c-0: nForce2 SMBus adapter at 0x4c00 >>> i2c_adapter i2c-1: nForce2 SMBus adapter at 0x4c40 >>> ACPI: PCI Interrupt 0000:02:07.0[A] -> Link [APC2] -> GSI 17 (level, >>> low) >>> -> IRQ 209 >>> ivtv0: Unreasonably low latency timer, setting to 64 (was 32) >>> ieee1394: Host added: ID:BUS[0-00:1023] GUID[0010dc00006baf5b] >>> ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) >>> ivtv0: loaded v4l-cx2341x-dec.fw firmware (262144 bytes) >>> tveeprom 2-0050: Huh, no eeprom present (err=-121)? >>> tveeprom 2-0050: Encountered bad packet header [01]. Corrupt or not a >>> Hauppauge eeprom. >>> ivtv0: Invalid EEPROM >>> ivtv0: Encoder revision: 0x02050032 >>> ivtv0: Decoder revision: 0x02020023 >>> ivtv0: Registered device video0 for encoder MPEG >>> ivtv0: Registered device video32 for encoder YUV >>> ivtv0: Registered device vbi0 for encoder VBI >>> ivtv0: Registered device video24 for encoder PCM audio >>> ivtv0: Registered device radio0 for encoder radio >>> ivtv0: Registered device video16 for decoder MPEG >>> ivtv0: Registered device vbi8 for decoder VBI >>> ivtv0: Registered device vbi16 for decoder VOUT >>> ivtv0: Registered device video48 for decoder YUV >>> ivtv0: loaded v4l-cx2341x-init.mpg firmware (155648 bytes) >>> ivtv0: i2c hardware 0x00000008 (msp3400) not found for command >>> 0xc008561c! >>> ivtv0: i2c addr 0x21 not found for command 0x4008646f! >>> ivtv0: i2c hardware 0x00000008 (msp3400) not found for command >>> 0x4008646d! >>> ivtv0: i2c hardware 0x00000008 (msp3400) not found for command >>> 0xc008561c! >>> ivtv0: i2c hardware 0x00000008 (msp3400) not found for command >>> 0xc008561c! >>> ivtv0: i2c hardware 0x00000008 (msp3400) not found for command >>> 0xc008561c! >>> ivtv0: Initialized Hauppauge WinTV PVR-350, card #0 >>> ivtv: ====================== NEXT CARD ====================== >>> _______________________________________________ ivtv-devel mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-devel
