I had a similar problem, try to set a module paramter "i2cnew=false" because also with my card the I2C code doesn't work!
Am Donnerstag, 14. Dezember 2006 17:36 schrieb Rich: > Does this mean something fatal has happend to this card? > > The card had been working for well over a year now. After moving from FC5 > ivtv v7.2 to FC6 ivtv v8.2 I am getting errors. The PVR500 card in this > system loads find. The other system that I have with a PVR-350 now > running FC6 ivtv v8.2 works fine. > > Thanks, > Rich > > ivtv: ==================== START INIT IVTV ==================== > ivtv: version 0.8.2 (tagged release) loading > ivtv: Linux version: 2.6.18-1.2849.fc6 SMP mod_unload gcc-4.1 > ivtv: In case of problems please include the debug info between > ivtv: the START INIT IVTV and END INIT IVTV lines, along with > ivtv: any module options, when mailing the ivtv-users mailinglist. > sd 0:0:0:0: Attached scsi generic sg0 type 0 > sd 1:0:0:0: Attached scsi generic sg1 type 0 > eth1: forcedeth.c: subsystem: 01462:0300 bound to 0000:00:05.0 > ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 21 > ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [APCJ] -> GSI 21 (level, high) > -> IRQ 193 > PCI: Setting latency timer of device 0000:00:06.0 to 64 > intel8x0_measure_ac97_clock: measured 51586 usecs > intel8x0: clocking to 46867 > ivtv0: Autodetected Hauppauge card (cx23415 based) > i2c_adapter i2c-0: nForce2 SMBus adapter at 0x4c00 > i2c_adapter i2c-1: nForce2 SMBus adapter at 0x4c40 > ACPI: PCI Interrupt 0000:02:07.0[A] -> Link [APC2] -> GSI 17 (level, low) > -> IRQ 209 > ivtv0: Unreasonably low latency timer, setting to 64 (was 32) > ieee1394: Host added: ID:BUS[0-00:1023] GUID[0010dc00006baf5b] > ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) > ivtv0: loaded v4l-cx2341x-dec.fw firmware (262144 bytes) > tveeprom 2-0050: Huh, no eeprom present (err=-121)? > tveeprom 2-0050: Encountered bad packet header [01]. Corrupt or not a > Hauppauge eeprom. > ivtv0: Invalid EEPROM > ivtv0: Encoder revision: 0x02050032 > ivtv0: Decoder revision: 0x02020023 > ivtv0: Registered device video0 for encoder MPEG > ivtv0: Registered device video32 for encoder YUV > ivtv0: Registered device vbi0 for encoder VBI > ivtv0: Registered device video24 for encoder PCM audio > ivtv0: Registered device radio0 for encoder radio > ivtv0: Registered device video16 for decoder MPEG > ivtv0: Registered device vbi8 for decoder VBI > ivtv0: Registered device vbi16 for decoder VOUT > ivtv0: Registered device video48 for decoder YUV > ivtv0: loaded v4l-cx2341x-init.mpg firmware (155648 bytes) > ivtv0: i2c hardware 0x00000008 (msp3400) not found for command 0xc008561c! > ivtv0: i2c addr 0x21 not found for command 0x4008646f! > ivtv0: i2c hardware 0x00000008 (msp3400) not found for command 0x4008646d! > ivtv0: i2c hardware 0x00000008 (msp3400) not found for command 0xc008561c! > ivtv0: i2c hardware 0x00000008 (msp3400) not found for command 0xc008561c! > ivtv0: i2c hardware 0x00000008 (msp3400) not found for command 0xc008561c! > ivtv0: Initialized Hauppauge WinTV PVR-350, card #0 > ivtv: ====================== NEXT CARD ====================== > > > _______________________________________________ > ivtv-devel mailing list > [email protected] > http://ivtvdriver.org/mailman/listinfo/ivtv-devel _______________________________________________ ivtv-devel mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-devel
