On Friday 15 December 2006 15:07, Gregor Fuis wrote:
> Hello,
>
> I have two cards, with 'ivtv_std=3' i managed to get sound on first
> cards. Can i configure card two with thist option 'ivtv_std=3,3'
No, it should be a global option. Please give the full INIT IVTV output
when you load the driver with the ivtv_std=3 option.
Hans
>
> Thanks
>
> Hans Verkuil wrote:
> > On Friday 15 December 2006 10:27, Gregor Fuis wrote:
> >> Hello,
> >>
> >> I have a problem with Secam standard on my PVR 350 cards. Picture
> >> is ok but i don't have any sound. I know that the format i am
> >> receiving is Secam G and i know that PVR 350 works ok with secam
> >> L. Diference in these two scams is SOund Carrier (Secam G = 5.5MHz
> >> , Secam L = 6.5MHz).
> >
> > You can try adding the module option 'ivtv_std=3' for the ivtv
> > module in /etc/modprobe.conf. That forces secam.
> >
> > If that doesn't work, then you have to upgrade to a newer kernel
> > (2.6.18 or higher). I'm pretty sure VLC works with later kernels
> > too. Any VLC users out there who can confirm this?
> >
> > Regards,
> >
> > Hans
> >
> >> I am using ivtv driver 0.4.6 with kernel 2.6.12. I can't use
> >> kernels 2.6.16 and higher becouse i am using VLC to stream
> >> channels on my STB. And VLC doesn't have V4L2 module for now.
> >>
> >> IVTV detect log:
> >>
> >> [4433624.327000] ivtv: ==================== START INIT IVTV
> >> ====================
> >> [4433624.327000] ivtv: version 0.4.6 (tagged release) loading
> >> [4433624.327000] ivtv: Linux version: 2.6.15.7-ubuntu1-iskratel
> >> 686 gcc-4.0 [4433624.327000] ivtv: In case of problems please
> >> include the debug info between
> >> [4433624.327000] ivtv: the START INIT IVTV and END INIT IVTV
> >> lines, along with
> >> [4433624.327000] ivtv: any module options, when mailing the
> >> ivtv-users mailinglist.
> >> [4433624.332000] ivtv0: Autodetected WinTV PVR 350 card (cx23415
> >> based) [4433624.333000] ACPI: PCI Interrupt 0000:01:03.0[A] -> GSI
> >> 16 (level, low) -> IRQ 17
> >> [4433624.333000] ivtv0: Unreasonably low latency timer, setting to
> >> 64 (was 16)
> >> [4433624.389000] tveeprom: ivtv version
> >> [4433624.389000] tveeprom: Hauppauge: model = 48139, rev = K2B7,
> >> serial# = 8612420
> >> [4433624.389000] tveeprom: tuner = Philips FM1216ME MK5 (idx =
> >> 117, type = 4)
> >> [4433624.389000] tveeprom: tuner fmt = PAL(B/G) PAL(I) SECAM(L/L')
> >> PAL(D/K) (eeprom = 0x74, v4l2 = 0x00400e17)
> >> [4433624.389000] tveeprom: audio processor = MSP4418 (type = 19)
> >> [4433624.389000] tveeprom: decoder processor = SAA7115 (type = 13)
> >> [4433624.389000] ivtv0: i2c attach to card #0 ok [client=tveeprom,
> >> addr=50] [4433624.410000] tuner (ivtv): chip found at addr 0xc2
> >> i2c-bus ivtv i2c driver #0
> >> [4433624.410000] ivtv0: i2c attach to card #0 ok [client=(tuner
> >> unset), addr=61]
> >> [4433624.615000] saa7115 2-0021: ivtv driver
> >> [4433624.615000] saa7115 2-0021: saa7115 found @ 0x42 (ivtv i2c
> >> driver #0) [4433624.779000] ivtv0: i2c attach to card #0 ok
> >> [client=saa7115, addr=21] [4433624.843000] saa7127 2-0044: ivtv
> >> driver
> >> [4433624.846000] saa7127 2-0044: saa7129 found @ 0x88 (ivtv i2c
> >> driver #0) [4433624.849000] ivtv0: i2c attach to card #0 ok
> >> [client=saa7127, addr=44] [4433624.871000] msp3400 2-0040: ivtv
> >> driver
> >> [4433624.871000] msp3400 2-0040: chip=MSP4418G-B3 +nicam +simple
> >> +simpler +radio mode=simpler
> >> [4433624.878000] ivtv0: i2c attach to card #0 ok
> >> [client=MSP4418G-B3, addr=40]
> >> [4433624.878000] msp3400 2-0040: msp34xxg daemon started
> >> [4433624.897000] tda9887 2-0043: (ivtv) chip found @ 0x86 (ivtv
> >> i2c driver #0)
> >> [4433624.897000] ivtv0: i2c attach to card #0 ok [client=tda9887,
> >> addr=43] [4433625.332000] ivtv0: loaded v4l-cx2341x-enc.fw
> >> firmware (262144 bytes) [4433625.443000] ivtv0: loaded
> >> v4l-cx2341x-dec.fw firmware (262144 bytes) [4433625.499000] ivtv0:
> >> Encoder revision: 0x02050032
> >> [4433625.501000] ivtv0: Decoder revision: 0x02020023
> >> [4433625.502000] ivtv0: Allocate DMA encoder MPEG stream: 128 x
> >> 32768 buffers (4096KB total)
> >> [4433625.503000] ivtv0: Allocate DMA encoder YUV stream: 161 x
> >> 12960 buffers (2048KB total)
> >> [4433625.505000] ivtv0: Allocate DMA encoder VBI stream: 80 x
> >> 26208 buffers (2048KB total)
> >> [4433625.506000] ivtv0: Allocate DMA encoder PCM audio stream: 455
> >> x 4608 buffers (2048KB total)
> >> [4433625.508000] ivtv0: Create encoder radio stream
> >> [4433625.509000] ivtv0: Allocate DMA decoder MPEG stream: 16 x
> >> 65536 buffers (1024KB total)
> >> [4433625.510000] ivtv0: Allocate DMA decoder VBI stream: 512 x
> >> 2048 buffers (1024KB total)
> >> [4433625.511000] ivtv0: Create decoder VOUT stream
> >> [4433625.513000] ivtv0: Allocate DMA decoder YUV stream: 20 x
> >> 51840 buffers (1024KB total)
> >> [4433625.606000] ivtv0: loaded v4l-cx2341x-init.mpg firmware
> >> (155648 bytes) [4433625.633000] tuner: type set to 38 (Philips
> >> PAL/SECAM multi (FM1216ME MK3)) by ivtv i2c driver #0
> >> [4433625.823000] ivtv0: Initialized WinTV PVR 350, card #0
> >>
> >>
> >> ivtvctl -d /dev/video0 -I --log-status
> >>
> >> SAA7115 reg[STATUS#1 - 0x1E] = 83
> >> Color Standard (D0-D1): SECAM
> >> White peak loop (D2): Not activated
> >> Gain value for act.lum. (min) (D3): Not limited
> >> Gain value for act.lum. (max) (D4): Not limited
> >> WIPA-mode slow-time constant (D5): Not activated
> >> Horizontal frequency (D6): Locked
> >> Field length (D7): Standard
> >>
> >> SAA7115 reg[STATUS#2 - 0x1F] = 91
> >> Ready for capture (D0): Yes
> >> Macrovision 7.01 (D1): No
> >> MV Colorstripe burst (D2): No
> >> MV Colorstripe burst type 3 (D3): No
> >> Input signal timebase (D4): Stable (broadcast/DVD)
> >> Field frequency (D5): 50Hz
> >> H & V loops (D6): Locked
> >> Interlace (D7): Detected
> >> ioctl VIDIOC_LOG_STATUS ok
> >> [4306273.339000] ivtv0: ================= START STATUS CARD #0
> >> =================
> >> [4306273.339000] saa7115 0-0021: Audio frequency: 48 kHz
> >> [4306273.341000] saa7115 0-0021: Video signal: broadcast/DVD
> >> [4306273.341000] saa7115 0-0021: Frequency: 50Hz
> >> [4306273.341000] saa7115 0-0021: Detected format: SECAM
> >> [4306273.341000] saa7127 0-0044: Standard: 50 Hz
> >> [4306273.341000] saa7127 0-0044: Input: normal
> >> [4306273.341000] saa7127 0-0044: Output: S-Video + Composite
> >> [4306273.341000] saa7127 0-0044: WSS: disabled
> >> [4306273.341000] saa7127 0-0044: VPS: disabled
> >> [4306273.341000] saa7127 0-0044: CC: disabled
> >> [4306273.341000] tda9887 0-0043: Data bytes: b=94 c=70 e=09
> >> [4306273.341000] ivtv0: ================== END STATUS CARD #0
> >> ==================
> >>
> >>
> >> If someone know solution for this please help me?
> >>
> >> Thanks,
> >>
> >> Gregor Fuis
> >>
> >> _______________________________________________
> >> ivtv-devel mailing list
> >> [email protected]
> >> http://ivtvdriver.org/mailman/listinfo/ivtv-devel
> >
> > _______________________________________________
> > ivtv-devel mailing list
> > [email protected]
> > http://ivtvdriver.org/mailman/listinfo/ivtv-devel
>
> _______________________________________________
> ivtv-devel mailing list
> [email protected]
> http://ivtvdriver.org/mailman/listinfo/ivtv-devel
_______________________________________________
ivtv-devel mailing list
[email protected]
http://ivtvdriver.org/mailman/listinfo/ivtv-devel
