Thanks Larry. But timing, full throttle, mixture , air speed indicator and 
Tacho were all the first things to be checked. It had high comp pistons, but 
due to low compression and broken rings on one cylinder, I removed them and 
fitted new standard 0200 pistons and rings, ran it in as per my LAME. Comps all 
78/80 runs sweet , but won’t handle the recommended 60x 70 
So still playing. No wheel pants yet, more concerned in getting RPM and prop 
correct first, more than IAS. 
PHIL. 

Sent from my iPhone

> On 9 Apr 2026, at 09:08, Larry Flesner via KRnet <[email protected]> wrote:
> 
> 
>> On 4/8/2026 5:03 PM, Phillip Matheson via KRnet wrote:
>> you may have missed what I getting at, my 0200 is . 2500 flat out down 
>> hill??with 59x 66 ?  At least you can dial yours back to 24 or 2500.
>> With the climb prop, 3000 rpm at 100kts
>> I may have to put the high compression pistons back in , ( but they caused 
>> other oil problems. At the moment it has new cylinders, standard pistons and 
>> compression ( leakage test @ 78/80 on all cylinders
>> 
>> Almost a waste of all that time building it to only fly at 100kts.
>> May I need to try another engine. But that’s a lot of work!!!!!!!!
>> Phil
> 
> +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
> 
> Phil,
> 
> I can feel your disappointment all the way to southern Illinois, USA !!!  
> BUT, I can't imagine your airspeed disappointment is 0-200 related unless it 
> has a major unidentified problem.  Until proven otherwise I'm betting it's 
> the prop or an extremely low reading ASI.
> 
> Many years ago, I started with an aged 0-200 (1800 hours since factory 
> overhaul) and a Ed Sterba 60D X 68P propeller.  I thought I should be able to 
> pull a bit more rpm so I returned it to Ed for re-pitch to a 64P.  I couldn't 
> tell any difference when I got it back so I'm not sure of the "exact" pitch.  
> I was topping out right at 2800rpm wide open at altitude.  I accepted that as 
> near ideal as the engine is rated 100hp at 2750 rpm and I didn't want to 
> stress a tired old engine.  I was indicating a quite accurate airspeed of 153 
> mph at 2500rpm.  I thought that was doing good considering 211LF is a 24" 
> stretch with raised canopy, longer gear legs with RV wheel covers at a power 
> setting the same as flying a C150.
> 
> Is there anyone in your part of the world with an 0-200 using a prop that is 
> pulling good rpm on a fast airplane? Zach is still running that Sterba 60D X 
> 68P? with over 1000+ hours with only refinish or two.
> 
> I would suggest you verify (sounds dumb) tach rpm with a hand held tach 
> checker.  Verify "full throttle".  Verify mag timing at 28* BTDC with new 
> cylinders.  If all that is spot on it has to  be the prop.  Does anyone in 
> the area have a ground adjustable prop to try?  By the way, do you have wheel 
> covers yet?  No wheel covers will cost you 12MPH+ at cruise.  If your engine 
> runs really cool you may be pushing too much (draggy) air through the cowl.  
> I closed the inlets down pretty small on 211LF and it still ran really nice 
> temps.
> 
> It's a KR!! Don't give up on it.  Treat it like a fine lady and give it what 
> it wants.......................................
> 
> Larry Flesner
> 
> --
> KRnet mailing list
> [email protected]
> https://list.krnet.org/mailman/listinfo/krnet
-- 
KRnet mailing list
[email protected]
https://list.krnet.org/mailman/listinfo/krnet

Reply via email to