By comparison, I was running a 62 x 66 Prince prop on the O-200 on my KR-2S.  
It was a rocket.  I did use 8.5:1 pistons and a tuned exhaust.  I put a lot of 
effort into drag reduction to get to those numbers.  I also eventually used 
P-mags for better fuel economy at altitude.  Normal cruise was 140KT with an 
impressive rate of climb.  After 24 years and 1400 hours, it moved to Canada a 
few years ago without me.

-Jeff Scott
Arkansas Ozarks


> Sent: Thursday, April 09, 2026 at 4:18 AM
> From: "Phillip Matheson via KRnet" <[email protected]>
> To: "KRnet" <[email protected]>
> Cc: "Phillip Matheson" <[email protected]>
> Subject: Re: KRnet> 0-200 kr slow
>
> Thanks Larry. But timing, full throttle, mixture , air speed indicator and 
> Tacho were all the first things to be checked. It had high comp pistons, but 
> due to low compression and broken rings on one cylinder, I removed them and 
> fitted new standard 0200 pistons and rings, ran it in as per my LAME. Comps 
> all 78/80 runs sweet , but won’t handle the recommended 60x 70 
> So still playing. No wheel pants yet, more concerned in getting RPM and prop 
> correct first, more than IAS. 
> PHIL. 
> 
> Sent from my iPhone
> 
> > On 9 Apr 2026, at 09:08, Larry Flesner via KRnet <[email protected]> 
> > wrote:
> > 
> > 
> >> On 4/8/2026 5:03 PM, Phillip Matheson via KRnet wrote:
> >> you may have missed what I getting at, my 0200 is . 2500 flat out down 
> >> hill??with 59x 66 ?  At least you can dial yours back to 24 or 2500.
> >> With the climb prop, 3000 rpm at 100kts
> >> I may have to put the high compression pistons back in , ( but they caused 
> >> other oil problems. At the moment it has new cylinders, standard pistons 
> >> and compression ( leakage test @ 78/80 on all cylinders
> >> 
> >> Almost a waste of all that time building it to only fly at 100kts.
> >> May I need to try another engine. But that’s a lot of work!!!!!!!!
> >> Phil
> > 
> > +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
> > 
> > Phil,
> > 
> > I can feel your disappointment all the way to southern Illinois, USA !!!  
> > BUT, I can't imagine your airspeed disappointment is 0-200 related unless 
> > it has a major unidentified problem.  Until proven otherwise I'm betting 
> > it's the prop or an extremely low reading ASI.
> > 
> > Many years ago, I started with an aged 0-200 (1800 hours since factory 
> > overhaul) and a Ed Sterba 60D X 68P propeller.  I thought I should be able 
> > to pull a bit more rpm so I returned it to Ed for re-pitch to a 64P.  I 
> > couldn't tell any difference when I got it back so I'm not sure of the 
> > "exact" pitch.  I was topping out right at 2800rpm wide open at altitude.  
> > I accepted that as near ideal as the engine is rated 100hp at 2750 rpm and 
> > I didn't want to stress a tired old engine.  I was indicating a quite 
> > accurate airspeed of 153 mph at 2500rpm.  I thought that was doing good 
> > considering 211LF is a 24" stretch with raised canopy, longer gear legs 
> > with RV wheel covers at a power setting the same as flying a C150.
> > 
> > Is there anyone in your part of the world with an 0-200 using a prop that 
> > is pulling good rpm on a fast airplane? Zach is still running that Sterba 
> > 60D X 68P? with over 1000+ hours with only refinish or two.
> > 
> > I would suggest you verify (sounds dumb) tach rpm with a hand held tach 
> > checker.  Verify "full throttle".  Verify mag timing at 28* BTDC with new 
> > cylinders.  If all that is spot on it has to  be the prop.  Does anyone in 
> > the area have a ground adjustable prop to try?  By the way, do you have 
> > wheel covers yet?  No wheel covers will cost you 12MPH+ at cruise.  If your 
> > engine runs really cool you may be pushing too much (draggy) air through 
> > the cowl.  I closed the inlets down pretty small on 211LF and it still ran 
> > really nice temps.
> > 
> > It's a KR!! Don't give up on it.  Treat it like a fine lady and give it 
> > what it wants.......................................
> > 
> > Larry Flesner
> > 
> > --
> > KRnet mailing list
> > [email protected]
> > https://list.krnet.org/mailman/listinfo/krnet
> -- 
> KRnet mailing list
> [email protected]
> https://list.krnet.org/mailman/listinfo/krnet
>
-- 
KRnet mailing list
[email protected]
https://list.krnet.org/mailman/listinfo/krnet

Reply via email to