Tim & Curt The only reason they do not start in the same place as far as I can see is because I disconnected the Router from the leadscrew to save my arm !! I went up to the LOM stop each time but must have been a turn of the handle a turn out i:e 1/4 inch. When I do the rest of the straight grooves to make the 10 cuts that will be it Then it may go on the scrap pile again I may even try 7 groove next time ?? Richard
On Wednesday, August 21, 2019 at 5:19:56 AM UTC+1, Curt George wrote: > > Hello Richard. > Nice job. Did the wave turn out as you had wanted ? > > I mean, if you did planed the cuts to work that way, I say, Awesome job ! > if not, do you know what happened? And or Why? > It took me a long time to figure out how to do that cut. > > Good job. I cant wait to see more. > > C.A.G. > > On Tuesday, August 20, 2019, 12:54:57 PM EDT, Richard Ellis < > rchrd...@gmail.com <javascript:>> wrote: > > > Here is a pic of the curves There are five curves and I was thinking of > putting a straight groove in between. All good practice !! > > On Tuesday, August 20, 2019 at 10:52:58 AM UTC+1, aussiman wrote: > > Looks good so far > > > > Bill > > > > *From:* legacy-orna...@ googlegroups.com <legacy-orna...@ googlegroups.com> > *On Behalf Of *Richard Ellis > *Sent:* Tuesday, 20 August 2019 4:59 PM > *To:* Legacy Ornamental Mills <legacy-orna...@ googlegroups.com> > > *Subject:* Re: TK Reciprocater long curves > > > > Just taken a quick pic of the basic (start ) of a coat and hat stand. > > It is 38 inches long X2 inch dia. May decde to make dia smaller !!! It of > course only approx half of the stand height. > > The four inch TK curve will be spaced eqidistance around the dia. but will > have a straight flute between each curve, > > Will take more pics Later if time permits !!?? > > On Tuesday, August 20, 2019 at 7:09:38 AM UTC+1, Richard Ellis wrote: > > Hi Bill Tim & Curt > > I will have to settle for a 4 inch curve When I have time to change the TK > to the 2X .Need a different gear set up for anything longer ( Not LOM ) > > I will update you when I take a pic of the wood I am using and it's > purpose also the dimensions. > > Bit too busy at the present time to do much with the Revo or 900. > > Richard > > On Sunday, August 18, 2019 at 5:38:02 PM UTC+1, Curt George wrote: > > Here is the longest pitch with a wave that I have done. Is this like what > you want to make? > > C.A.G. > > [image: Inline image] > > On Sunday, August 18, 2019, 11:12:04 AM EDT, 'Curt George' via Legacy > Ornamental Mills <legacy-orna...@googlegroups. com> wrote: > > > > > > Good morning. > > Richard, What router bit are you using? > > > > What Tim and Bill already said are correct. but the type of cut you make > also makes the wave look different. depending on the diameter of the work > piece and the cutter's size, as well as the depth of your cut will give you > different looks. And also will the method of cutting. (Cutting for the top > vs cutting form the side of the wood will also change the look.) > > > > Here are a few different looks you can get with a long pitch and different > cutters. > > > > C.A.G. > > > > On Sunday, August 18, 2019, 07:53:29 AM EDT, <bulk...@mmnet.com.au> > wrote: > > > > > > If I remember correctly the wave or zigzag the biggest you can achieve as > it travels along is around 90 degrees so virtually no degrees to 90. > > > > But the pitch how long the waves are governed by the pitch just the same > as spirals are so do some waves at different pitches and see, so my guess > would be yes 2x would give 4 inch . please report how you go I would be > greatly interested to see, if it wasn’t so dam cold here out in the shop I > would try a few and report back. > > > > Bill > > > > *From:* legacy-orna...@googlegroups. com <legacy-orna...@googlegroups. com> > *On Behalf Of *Richard Ellis > *Sent:* Sunday, 18 August 2019 7:47 PM > *To:* Legacy Ornamental Mills <legacy-orna...@googlegroups. com> > *Subject:* TK Reciprocater long curves > > > > Hi all you LOM experts > > I am trying to do a long (approx ) 6 inch flute with the TK at present > with the standard index gear I get a 2 inch point to point curve > > If I change to the 2X gear I think it will only give me a four inch point > to point --- I have not tried but it's my guess !! > > Am I trying to do the impossible??? > > Richard > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+ unsubscr...@googlegroups.com. > To view this discussion on the web visit https://groups.google.com/d/ > msgid/legacy-ornamental-mills/ e560996b-0be6-44a0-8bf9- > abf99146f57c%40googlegroups. com > <https://groups.google.com/d/msgid/legacy-ornamental-mills/e560996b-0be6-44a0-8bf9-abf99146f57c%40googlegroups.com?utm_medium=email&utm_source=footer> > . > > > > > <https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient> > > Virus-free. www.avast.com > <https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient> > > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+ unsubscr...@googlegroups.com. > To view this discussion on the web visit https://groups.google.com/d/ > msgid/legacy-ornamental-mills/ 000001d555bb%24878d08f0% > 2496a71ad0%24%40mmnet.com.au > <https://groups.google.com/d/msgid/legacy-ornamental-mills/000001d555bb%24878d08f0%2496a71ad0%24%40mmnet.com.au?utm_medium=email&utm_source=footer> > . > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+ unsubscr...@googlegroups.com. > To view this discussion on the web visit https://groups.google.com/d/ > msgid/legacy-ornamental-mills/ 762244031.589832. > 1566141100017%40mail.yahoo.com > <https://groups.google.com/d/msgid/legacy-ornamental-mills/762244031.589832.1566141100017%40mail.yahoo.com?utm_medium=email&utm_source=footer> > > . > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+ unsubscr...@googlegroups.com. > To view this discussion on the web visit https://groups.google.com/d/ > msgid/legacy-ornamental-mills/ 02923194-a11a-4804-8ac2- > cd41967adfb1%40googlegroups. com > <https://groups.google.com/d/msgid/legacy-ornamental-mills/02923194-a11a-4804-8ac2-cd41967adfb1%40googlegroups.com?utm_medium=email&utm_source=footer> > . > > > <https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient> > Virus-free. > www.avast.com > <https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient> > > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com > <javascript:>. > To view this discussion on the web visit > > https://groups.google.com/d/msgid/legacy-ornamental-mills/5ed55d80-e6fa-4977-a6bb-61459f288955%40googlegroups.com > > <https://groups.google.com/d/msgid/legacy-ornamental-mills/5ed55d80-e6fa-4977-a6bb-61459f288955%40googlegroups.com?utm_medium=email&utm_source=footer> > . > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/b5c47ca5-eeb7-48d3-b771-74f25db05abe%40googlegroups.com.
