Sorry everyone I know most of you don’t know what I’m saying but all will be clear with curts video
Bill From: legacy-ornamental-mills@googlegroups.com <legacy-ornamental-mills@googlegroups.com> On Behalf Of bulke...@mmnet.com.au Sent: Thursday, 22 August 2019 3:10 PM To: legacy-ornamental-mills@googlegroups.com Subject: RE: TK Reciprocater long curves Curt can you get all the lines to line up perfectly on the opposite line? when you’re going to do the second wave of the DNA pattern. in your video It looks like the gear on the leadscrew is out a little on the second cut. I would be inclined to engauge the leadscrew nut and undo the duplex gear from the direction gears and rotate it half a turn to the other line making sure the pitch gears don’t move then re-mesh and tighten again. I’m sure that’s what I did. Bill From: 'Curt George' via Legacy Ornamental Mills <legacy-ornamental-mills@googlegroups.com <mailto:legacy-ornamental-mills@googlegroups.com> > Sent: Thursday, 22 August 2019 2:36 PM To: legacy-ornamental-mills@googlegroups.com <mailto:legacy-ornamental-mills@googlegroups.com> Subject: Re: TK Reciprocater long curves Hello everyone. I plan to re-do my attempt to show how I use the wave attachment, But for now this is what I do. ((I would like to say one more thing, My way is how, I do it. by no means is my way the only way it can work. )) First I set my pitch, and wave's width. (moving the pivot arm to make my off-set/ width of the wave.) Then I set my stops, and plan for the starting point. Before I make my first cut I use a sharpy marker, and draw a line through the gears. (this line will ONLY line up when the gears are exactly where they were when I started my cut./ perfect alignment.) I make my cut. and then return the carriage to the start point. Now I re-align the gears/markings. once the gears are set, then I move the indexing plate to the next cut, locking the pin into its hole on the indexing plate, and then repeating my cut... this process goes on over and over until I have finished. Now if I plan to do the DnA cut for example. I have to make two markings of the gears before I start. this time the alignment of the gears has more to do with the indexing arm's placement, Depending on what side of the center. "0" (Do-plex gears),The arc of the arm will effect the direction of the wave. Its not hard to do. And I plan to show step by step on the next attempt I make. My hope is that I can talk my son into filming this, perhaps this weekend? at this time it all depends on my, and my sons work. (The filming of this, will happen soon, I promise.) ;-) Keep up the good work, and Please let us know how it turns out for you. C.A.G. On Wednesday, August 21, 2019, 02:06:19 PM EDT, Tim Ziegler <timjzieg...@gmail.com <mailto:timjzieg...@gmail.com> > wrote: Yes I agree with Bill more videos for us guys that are learning the LOM the better. Kind Regards, Timothy J. Ziegler Ziegler WoodWork & Specialty 14171 160th Ave. Foreston MN 56330 320-294-5798 shop 320-630-2243 cell On Wed, Aug 21, 2019 at 12:59 PM <bulke...@mmnet.com.au <mailto:bulke...@mmnet.com.au> > wrote: You should do a video anyway curt so others watching can see how its done Bill From: 'Curt George' via Legacy Ornamental Mills <legacy-ornamental-mills@googlegroups.com <mailto:legacy-ornamental-mills@googlegroups.com> > Sent: Wednesday, 21 August 2019 11:34 PM To: legacy-ornamental-mills@googlegroups.com <mailto:legacy-ornamental-mills@googlegroups.com> Subject: Re: TK Reciprocater long curves Richard Like I posted on the wave attachment video. Mark your gears to keep your placement. Your mistake was caused when you started up due to the swing arm was not in syn with where you were on the other cut. Now this is pretty neat. depending on the gear placement and, the position of the pivot arm being in the same side of center when you start your cut will effect your cut. As an example, On the left of center (the pivot arm, not the gears.) will pull on the start of your cut, and in the same placement of your gears,If you make your pivot arm set on the right side of center, the pivot arm will push. What I do when I want to make this design. is to mark the gears with two colors of sharpy marker. 90 deg. form each other. (as an example on cut will be Green, and the other will be RED.) that way when I start everything will be uniformed. I hope this is clear to you? If not I will see if I can make a better video for you . Mark your gear placement before you make your first cut. and then make sure of the placement of the pivot arm (on which side of center you are on.) will effect your wave direction. I wish you luck. Play as much as you can with your machine before you start . Dont waist good wood on practice parts, when it counts, you need to know what is happening and why. and knowing is half the battle. ;-) C.A.G. On Wednesday, August 21, 2019, 02:25:53 AM EDT, Richard Ellis <rchrd.ell...@gmail.com <mailto:rchrd.ell...@gmail.com> > wrote: Tim & Curt The only reason they do not start in the same place as far as I can see is because I disconnected the Router from the leadscrew to save my arm !! I went up to the LOM stop each time but must have been a turn of the handle a turn out i:e 1/4 inch. When I do the rest of the straight grooves to make the 10 cuts that will be it Then it may go on the scrap pile again I may even try 7 groove next time ?? Richard On Wednesday, August 21, 2019 at 5:19:56 AM UTC+1, Curt George wrote: Hello Richard. Nice job. Did the wave turn out as you had wanted ? I mean, if you did planed the cuts to work that way, I say, Awesome job ! if not, do you know what happened? And or Why? It took me a long time to figure out how to do that cut. Good job. I cant wait to see more. C.A.G. On Tuesday, August 20, 2019, 12:54:57 PM EDT, Richard Ellis <rchrd...@gmail.com <mailto:rchrd...@gmail.com> > wrote: Here is a pic of the curves There are five curves and I was thinking of putting a straight groove in between. All good practice !! On Tuesday, August 20, 2019 at 10:52:58 AM UTC+1, aussiman wrote: Looks good so far Bill From: legacy-orna...@ googlegroups.com <http://googlegroups.com> <legacy-orna...@ googlegroups.com <http://googlegroups.com> > On Behalf Of Richard Ellis Sent: Tuesday, 20 August 2019 4:59 PM To: Legacy Ornamental Mills <legacy-orna...@ googlegroups.com <http://googlegroups.com> > Subject: Re: TK Reciprocater long curves Just taken a quick pic of the basic (start ) of a coat and hat stand. It is 38 inches long X2 inch dia. May decde to make dia smaller !!! It of course only approx half of the stand height. The four inch TK curve will be spaced eqidistance around the dia. but will have a straight flute between each curve, Will take more pics Later if time permits !!?? On Tuesday, August 20, 2019 at 7:09:38 AM UTC+1, Richard Ellis wrote: Hi Bill Tim & Curt I will have to settle for a 4 inch curve When I have time to change the TK to the 2X .Need a different gear set up for anything longer ( Not LOM ) I will update you when I take a pic of the wood I am using and it's purpose also the dimensions. Bit too busy at the present time to do much with the Revo or 900. Richard On Sunday, August 18, 2019 at 5:38:02 PM UTC+1, Curt George wrote: Here is the longest pitch with a wave that I have done. Is this like what you want to make? C.A.G. <https://groups.google.com/group/legacy-ornamental-mills/attach/e0b3e7c62df30/long%20wave.JPG?part=0.1&view=1&authuser=0> On Sunday, August 18, 2019, 11:12:04 AM EDT, 'Curt George' via Legacy Ornamental Mills <legacy-orna...@googlegroups. com <mailto:legacy-orna...@googlegroups.%20com> > wrote: Good morning. Richard, What router bit are you using? What Tim and Bill already said are correct. but the type of cut you make also makes the wave look different. depending on the diameter of the work piece and the cutter's size, as well as the depth of your cut will give you different looks. And also will the method of cutting. (Cutting for the top vs cutting form the side of the wood will also change the look.) Here are a few different looks you can get with a long pitch and different cutters. C.A.G. On Sunday, August 18, 2019, 07:53:29 AM EDT, <bulk...@mmnet.com.au <mailto:bulk...@mmnet.com.au> > wrote: If I remember correctly the wave or zigzag the biggest you can achieve as it travels along is around 90 degrees so virtually no degrees to 90. But the pitch how long the waves are governed by the pitch just the same as spirals are so do some waves at different pitches and see, so my guess would be yes 2x would give 4 inch . please report how you go I would be greatly interested to see, if it wasn’t so dam cold here out in the shop I would try a few and report back. Bill From: legacy-orna...@googlegroups <mailto:legacy-orna...@googlegroups> . com <legacy-orna...@googlegroups. com <mailto:legacy-orna...@googlegroups.%20com> > On Behalf Of Richard Ellis Sent: Sunday, 18 August 2019 7:47 PM To: Legacy Ornamental Mills <legacy-orna...@googlegroups. com <mailto:legacy-orna...@googlegroups.%20com> > Subject: TK Reciprocater long curves Hi all you LOM experts I am trying to do a long (approx ) 6 inch flute with the TK at present with the standard index gear I get a 2 inch point to point curve If I change to the 2X gear I think it will only give me a four inch point to point --- I have not tried but it's my guess !! Am I trying to do the impossible??? Richard -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+ unsubscr...@googlegroups.com <mailto:unsubscr...@googlegroups.com> . To view this discussion on the web visit https://groups.google.com/d/ msgid/legacy-ornamental-mills/ e560996b-0be6-44a0-8bf9- abf99146f57c%40googlegroups. com <https://groups.google.com/d/msgid/legacy-ornamental-mills/e560996b-0be6-44a0-8bf9-abf99146f57c%40googlegroups.com?utm_medium=email&utm_source=footer> . <https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient> Virus-free. <https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient> www.avast.com -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+ unsubscr...@googlegroups.com <mailto:unsubscr...@googlegroups.com> . To view this discussion on the web visit https://groups.google.com/d/ msgid/legacy-ornamental-mills/ 000001d555bb%24878d08f0% 2496a71ad0%24%40mmnet.com.au <https://groups.google.com/d/msgid/legacy-ornamental-mills/000001d555bb%24878d08f0%2496a71ad0%24%40mmnet.com.au?utm_medium=email&utm_source=footer> . -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+ unsubscr...@googlegroups.com <mailto:unsubscr...@googlegroups.com> . To view this discussion on the web visit https://groups.google.com/d/ msgid/legacy-ornamental-mills/ 762244031.589832. 1566141100017%40mail.yahoo.com <https://groups.google.com/d/msgid/legacy-ornamental-mills/762244031.589832.1566141100017%40mail.yahoo.com?utm_medium=email&utm_source=footer> . -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+ unsubscr...@googlegroups.com <mailto:unsubscr...@googlegroups.com> . To view this discussion on the web visit https://groups.google.com/d/ msgid/legacy-ornamental-mills/ 02923194-a11a-4804-8ac2- cd41967adfb1%40googlegroups. com <https://groups.google.com/d/msgid/legacy-ornamental-mills/02923194-a11a-4804-8ac2-cd41967adfb1%40googlegroups.com?utm_medium=email&utm_source=footer> . <https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient> Virus-free. <https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient> www.avast.com -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+ unsubscr...@googlegroups.com <mailto:unsubscr...@googlegroups.com> . To view this discussion on the web visit https://groups.google.com/d/ msgid/legacy-ornamental-mills/ 5ed55d80-e6fa-4977-a6bb- 61459f288955%40googlegroups. com <https://groups.google.com/d/msgid/legacy-ornamental-mills/5ed55d80-e6fa-4977-a6bb-61459f288955%40googlegroups.com?utm_medium=email&utm_source=footer> . -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com <mailto:legacy-ornamental-mills+unsubscr...@googlegroups.com> . To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/b5c47ca5-eeb7-48d3-b771-74f25db05abe%40googlegroups.com <https://groups.google.com/d/msgid/legacy-ornamental-mills/b5c47ca5-eeb7-48d3-b771-74f25db05abe%40googlegroups.com?utm_medium=email&utm_source=footer> . -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com <mailto:legacy-ornamental-mills+unsubscr...@googlegroups.com> . To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/1570093383.171695.1566394432033%40mail.yahoo.com <https://groups.google.com/d/msgid/legacy-ornamental-mills/1570093383.171695.1566394432033%40mail.yahoo.com?utm_medium=email&utm_source=footer> . <https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient> Virus-free. <https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient> www.avast.com -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com <mailto:legacy-ornamental-mills+unsubscr...@googlegroups.com> . To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/000501d5584a%241fd080c0%245f718240%24%40mmnet.com.au <https://groups.google.com/d/msgid/legacy-ornamental-mills/000501d5584a%241fd080c0%245f718240%24%40mmnet.com.au?utm_medium=email&utm_source=footer> . -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com <mailto:legacy-ornamental-mills+unsubscr...@googlegroups.com> . To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLFqvBzziLNgjt2xqRY0VCAtmQFSVi%3DZ%3DMTK04auScvP-A%40mail.gmail.com <https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLFqvBzziLNgjt2xqRY0VCAtmQFSVi%3DZ%3DMTK04auScvP-A%40mail.gmail.com?utm_medium=email&utm_source=footer> . -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com <mailto:legacy-ornamental-mills+unsubscr...@googlegroups.com> . To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/861244746.437020.1566448569842%40mail.yahoo.com <https://groups.google.com/d/msgid/legacy-ornamental-mills/861244746.437020.1566448569842%40mail.yahoo.com?utm_medium=email&utm_source=footer> . -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com <mailto:legacy-ornamental-mills+unsubscr...@googlegroups.com> . To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/000001d558a7%24d38fb150%247aaf13f0%24%40mmnet.com.au <https://groups.google.com/d/msgid/legacy-ornamental-mills/000001d558a7%24d38fb150%247aaf13f0%24%40mmnet.com.au?utm_medium=email&utm_source=footer> . --- This email has been checked for viruses by Avast antivirus software. https://www.avast.com/antivirus -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/000701d558af%2473047250%24590d56f0%24%40mmnet.com.au.