Hi Guy,
I had the same problem compiling the latest kernel on my PII-450.
I notised that I had compiled it for a PIII and changed this ?!
Booted perfectly after that !
//Patrik
Guy Plunkett wrote:
>
> on 15/11/2000 11:56, Garst R. Reese at [EMAIL PROTECTED] typed:
>
> >
> >
> > Guy Plunkett wrote:
> >>
> >> on 15/11/2000 08:32, Garst R. Reese at [EMAIL PROTECTED] typed:
> >>
> >>>
> >>>
> >>> Jonathan Hudson wrote:
> >>>>
> >>>> In article <[EMAIL PROTECTED]>,
> >>>> Guy Plunkett <[EMAIL PROTECTED]> writes:
> >>>> GP>
> >>>> GP> Thanks for the information....
> >>>> GP>
> >>>> GP> I'm downloading linux-2.4.0-test10.tar.gz kernel source..
> >>>> GP>
> >>>> GP> Can you point me in the direction of any and all patches that I
> >>> should apply
> >>>> GP> to get the IRDA working?
> >>>>
> >>>> I find test11-pre4 (the latest pre test 11) works just fine; modulo
> >>>> any compilation problems listed here for hardware I don't have :)
> >>>>
> >>>> _______________________________________________
> >>>> Linux-IrDA mailing list - [EMAIL PROTECTED]
> >>>> http://www.pasta.cs.UiT.No/mailman/listinfo/linux-irda
> >>> After much discussion the IrDA patches went into test11-pre3 and bugs
> >>> were fixed
> >>> in test11-pre4. Nothing earlier works.
> >>> The patches are in kernel/testing.
> >>> Garst
> >>> _______________________________________________
> >>> Linux-IrDA mailing list - [EMAIL PROTECTED]
> >>> http://www.pasta.cs.UiT.No/mailman/listinfo/linux-irda
> >>>
> >>
> >> Ok here's the story so far.....
> >>
> >> I've downloaded linux-2.4.0-test10.tgz
> >> I've extracted and patched with test11-pre3.gz all works ok... no errors
> > :-)
> >>
> >> I run make xconfig:
> >> Code maturity level: Yes
> >> Realtek TRL-8139 PCI fast ethernet Adapter Support: Yes
> >> IRDA subsystem support: M
> >> IRLan Protocol: N
> >> IRNet Protocol: N
> >> IRComm Protocol: M
> >> Ultra: N
> >> IRDA Protocol options: N
> >> Irtty: M
> >> IrPort: M
> >>
> >> Everything else as defaults
> >>
> >> make dep
> >> make bzImage
> >> make modules
> >> make modules_install
> >> - have to edit makefile so that -F is -m for the system.map
> >>
> >> I then copy the Sytem.map file to /boot/System.map-2.4.0-test11
> >>
> >> I configure lilo using linuxconf...
> >> all goes well..I've done this a few times now and previously works
> > fine
> >>
> >> However with this kernel...
> >>
> >> I select it at the boot prompt. and it loads the kernel and then
> > freezes...
> >>
> >> Any ideas????
> >>
> >> please all I want to do is be able to ir link my palm the hotsync
> >>
> >> Thanks
> > test11-pre3 isn't all the way working.
> > try pre5. You have to back-out pre3 before applying pre5.
> > But, pre4 and pre5 screwed up my apm with X and some apps running.
> > Garst
> > _______________________________________________
> > Linux-IrDA mailing list - [EMAIL PROTECTED]
> > http://www.pasta.cs.UiT.No/mailman/listinfo/linux-irda
> >
>
> Hello...
>
> just patch for pre5...
>
> configured as before... but I get the same problem
>
> LILO boot: linux-2.4.0
>
> Loading linux-2.4.0....................
> Uncompressing Linux... Ok, booting the kernel.
>
> Then nothing... the computer just sits there...
>
> Any ideas???
>
> Thanks
>
> -- Guy
> ------------------------------------------
> Guy Plunkett Bsc (Hons), CLP ICQ:61446480
> Systems Support Engineer --> Mac, UNIX, PC
> ABC Solutions -> http://www.abcworks.co.uk
> Tel: +441582 461040 -- Fax: +441582 461742
>
> _______________________________________________
> Linux-IrDA mailing list - [EMAIL PROTECTED]
> http://www.pasta.cs.UiT.No/mailman/listinfo/linux-irda
--
------------------------------------------------
Tankebolaget AB
Kungstensgatan 21B II, 113 57 Stockholm
+46-(0)8-442 96 04 / +46-(0)70-810 49 91
------------------------------------------------
"That vulnerability is completely theoretical."
-- Microsoft
------------------------------------------------
S/MIME Cryptographic Signature
