>From the Sane umax-scsi documentation at
http://www.Wolfsburg.DE/~rauch/sane/sane-umax-config-doc.html
It shows to use a driver for an NCR5380 SCSI controller. The sample command
they show is
insmod g_NCR5380 ncr_irq=255 ncr_addr=0x280 dtc_3181e=1
You may have to play around with the ncr_addr part. They list a whole bunch
of IO addresses the controller card can use.
> -----Original Message-----
> From: Joao C Agostini [SMTP:[EMAIL PROTECTED]]
> Sent: Wednesday, August 11, 1999 10:55 AM
> To: [EMAIL PROTECTED]
> Subject: Re: [newbie] How do I install my scanner Umax S-6E?
>
> Hi
>
> Thank you for your concern. I had already seen Sane and in its
> documents I read that was necessary that the kernel should have the
> module for a generic scsi board, for that I asked the list if somebody
> knows which is that module and as I do to carry him/it. Who can me that
> to answer he/she would thank.
>
> "Martin, Darin W." ha scritto:
> >
> > Joao,
> > Before spending the money on a new SCSI card, go to the SANE page and
> try
> > their drivers. They list your scanner and the controller it comes with
> as
> > supported.. Their site is at http://www.mostang.com/sane/
> >
> > > -----Original Message-----
> > > From: Joao C Agostini [SMTP:[EMAIL PROTECTED]]
> > > Sent: Monday, August 09, 1999 10:19 PM
> > > To: [EMAIL PROTECTED]
> > > Subject: Re: [newbie] How do I install my scanner Umax S-6E?
> > >
> > > Hello
> > >
> > > Thank you very much for the information and for the attention.
> It is
> > > a
> > > sad news, but I will take your advice because, I find, this will be
> the
> > > only form of doing my scanner to work. But, even so, I would like
> > > something to know on which module for a generic board scsi, do you
> know?
> > > Thank you again.
> > >
> > > Steve Philp ha scritto:
> > > >
> > > > Joao C Agostini wrote:
> > > > >
> > > > > Hello
> > > > >
> > > > > Does by chance anybody have a scanner of the mark Umax
> S-6E? I
> > > saw in
> > > > > the sane that there is the drive for him, but when I made the
> > > > > installation of Mandrake it didn't consist a scsi board for him. I
> > > wrote
> > > > > for to Umax so that they informed me which the type of the scsi
> board
> > > > > that they used for S-6E, but until today I didn't obtain answer.
> Did I
> > > > > Read in the documents of the sane that the kernel should include a
> > > > > module (?) of generic scsi, what module is this? How do I do so
> that
> > > it
> > > > > is carried by the kernel or so that it is included in him? What
> should
> > > > > read to enable my scanner? At once thank you very much.
> > > >
> > > > The SCSI board that ships with the S-6E is a completely worthless
> piece
> > > > of crap and should be tossed into the nearest trash can. Pick up a
> > > > cheap Adaptec and install the kernel drivers for it and you'll be
> fine
> > > > with that scanner. I used to run the same here with an AHA-1524
> card
> > > > (at least, I think that was the number of the card, it's been
> awhile).
> > > >
> > > > --
> > > > Steve Philp
> > > > Network Administrator
> > > > Advance Packaging Corp.
> > > > [EMAIL PROTECTED]
> > >
> > > --
> > > Joăo Carlos <[EMAIL PROTECTED]>
> > > <Brasil - SP> ICQ - 33.965.439
> > > usuário Linux # 106644
>
> --
> Joăo Carlos <[EMAIL PROTECTED]>
> <Brasil - SP> ICQ - 33.965.439
> usuário Linux # 106644
