On Sunday 15 Dec 2002 10:03 pm, Steve Jeppesen wrote: > Anne, > for what it is worth, this is what I did in order to get the .jpg and > .avi files off my Fuji FinePix A303 (early x-mas gift for the family!) > > All I had to load was usb-storage, the same other two you have loaded; > usb-uhci and usbcore were already loaded - I have no idea about usb-scsi > and why it is working for me without it. > > I created /mnt/camera as stated before (although I am not sure if this > was really needed because after a re-boot I had /mnt/removable somehow > also) and then while the camera was turned on and connected to the usb > port I rebooted. > > I ran dmesg just to make sure after the system booted up and it did id > the Fuji camera. >
dmesg seems to see it, it certainly lists enough devices, but doesn't seem to know much about them. The 4-port hub has printer, scanner, LS120 drive and now camera. > Then I mounted the contents of the cameras memory; > mount -t vfat /dev/sda1 /mnt/camera > (even though while browsing /dev I did not see sda1) and all the .jpg's > and 1 .avi file I took with the camera were buried in a couple of > sub-folders inside/mnt/camera Because the LS120 is seen as sda I assume that this has to be sdb. Following notes sent to me by John, I created a node sdb. I rebooted with everything plugged in and switched on, but attempts to mount get [root@anne-linux anne]# mount /dev/sdb /mnt/camera mount: No medium found The out put of dmesg should mean something to someone, so I'm going to quote the part that relates to usb: usb-uhci.c: USB UHCI at I/O 0xd000, IRQ 5 usb-uhci.c: Detected 2 ports usb.c: new USB bus registered, assigned bus number 2 hub.c: USB hub found hub.c: 2 ports detected usb-uhci.c: v1.275:USB Universal Host Controller Interface driver usbdevfs: remount parameter error usb.c: registered new driver usblp printer.c: v0.11: USB Printer Device Class driver EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide2(33,65), internal journal Adding Swap: 530104k swap-space (priority -1) hub.c: USB new device connect on bus2/1, assigned device number 2 Adding Swap: 248968k swap-space (priority -2) hub.c: USB hub found hub.c: 4 ports detected hub.c: USB new device connect on bus2/2, assigned device number 3 hub.c: USB hub found hub.c: 4 ports detected hub.c: USB new device connect on bus2/1/1, assigned device number 4 usb.c: USB device 4 (vend/prod 0x718/0x2) is not claimed by any active driver. hub.c: USB new device connect on bus2/1/2, assigned device number 5 printer.c: usblp0: USB Bidirectional printer dev 5 if 0 alt 0 proto 2 vid 0x03F0 pid 0x3304 hub.c: USB new device connect on bus2/1/3, assigned device number 6 usb.c: USB device 6 (vend/prod 0x4b8/0x110) is not claimed by any active driver. Initializing USB Mass Storage driver... usb.c: registered new driver usb-storage usb-uhci.c: interrupt, status 3, frame# 1650 usb.c: registered new driver usbscanner usb_control/bulk_msg: timeout scsi1 : SCSI emulation for USB Mass Storage devices Vendor: MATSHITA Model: LS-120 VER5 00 Rev: F523 Type: Direct-Access ANSI SCSI revision: 02 Attached scsi removable disk sda at scsi1, channel 0, id 0, lun 0 sda : READ CAPACITY failed. sda : status = 1, message = 00, host = 0, driver = 08 Current sd00:00: sense key Not Ready Additional sense indicates Medium not present sda : block size assumed to be 512 bytes, disk size 1GB. /dev/scsi/host1/bus0/target0/lun0: I/O error: dev 08:00, sector 0 I/O error: dev 08:00, sector 0 unable to read partition table WARNING: USB Mass Storage data integrity not assured USB Mass Storage device found at 4 USB Mass Storage support registered. scanner.c: 0.4.6:USB Scanner Driver Device not ready. Make sure there is a disc in the drive. VFS: Disk change detected on device 08:00 sda : READ CAPACITY failed. sda : status = 1, message = 00, host = 0, driver = 08 Current sd00:00: sense key Not Ready Additional sense indicates Medium not present sda : block size assumed to be 512 bytes, disk size 1GB. /dev/scsi/host1/bus0/target0/lun0: I/O error: dev 08:00, sector 0 I/O error: dev 08:00, sector 0 Device not ready. Make sure there is a disc in the drive. VFS: Disk change detected on device 08:00 sda : READ CAPACITY failed. sda : status = 1, message = 00, host = 0, driver = 08 Current sd00:00: sense key Not Ready Additional sense indicates Medium not present sda : block size assumed to be 512 bytes, disk size 1GB. /dev/scsi/host1/bus0/target0/lun0: I/O error: dev 08:00, sector 0 I/O error: dev 08:00, sector 0 spurious 8259A interrupt: IRQ7. scsi2 : SCSI host adapter emulation for IDE ATAPI devices Vendor: MITSUMI Model: CR-48X9TE Rev: 1.0C Type: CD-ROM ANSI SCSI revision: 02 hda: ATAPI 40X DVD-ROM drive, 512kB Cache, DMA Uniform CD-ROM driver Revision: 3.12 It's clearly not happy about the LS120, which is not working as it should (and did up to 2 weeks ago). There was no disk in the drive at the time of booting. The camera was switched on in play mode - I presume that's right? I wish I understood what's happening here. It's getting depressing. Anne
Want to buy your Pack or Services from MandrakeSoft? Go to http://www.mandrakestore.com
