Dennis,

Yes i do have the OEM manual.

That's exactly right - i turned the engine a few revolutions and the
chain is taught then loose (it must be from the different states of
torque on the cams shafts).  In the slack state the chain has about .
4" of vertical movement.

Ok - I'm going to fix this.  I'll just follow the Honda OEM manual to
take the cams shafts out and replace the parts.

I suspect if i don't find damage on the chain guides, and the chain
has not strethed beyond spec, then i just need to purchase #3 in the
link below which is P/N "Bracket, Tensioner 14500-ME5-030 (it includes
the spring, the lower link the spring attaches to, and the spring
tube).  Does this sound right?  It's $79.

http://www.rosevillecyclecenter.com/fiche_section_detail.asp?section=123812&category=MOTORCYCLES&make=HONDA&year=1983&fveh=2958

Was there a factory recall to change these tensioners originally?
Perhaps mine was never changed. Seems that a lot of 650's have this
problem..

Thanks,

Paul

On Aug 22, 9:33 pm, Dennis Hammerl <[email protected]> wrote:
> If you do really understand how it works, then go ahead and turn the 
> crankshaft (by hand, slowly) and watch what happens. There will be a place in 
> rotation (do it many times) where the cam chain will be quite slack. The 
> tension on it changes during rotation. Rotating the crankshaft backwards may 
> show the slack spot more easily.  There was an update tensioner for '83  
> models. All new parts supersede to the update. I would replace with the new 
> part and not attempt a repair of the original. It's a bear of a job but can 
> be done without making a real mess of the motor. Leave the cylinder head on. 
> Unless, of course you're replacing the cam chain too. You have the OEM manual 
> ?  Good instructions for removal. The tensioner must be unloaded to be 
> removed. The manual does not address the dynamic of changing tensions during 
> running. The failed tensioner is not controlling the chain during a lightly 
> loaded situation. The spring isn't strong enough to work
>  properly. All these things are cured with the update.
>
> --- On Sat, 8/22/09, oldschoolgwin <[email protected]> wrote:
>
> From: oldschoolgwin <[email protected]>
> Subject: [Nighthawk Lovers] NH650 - Automatic cam chain tensioner inspection 
> findings.
> To: "Nighthawk Motorcycle Lovers!" <[email protected]>
> Date: Saturday, August 22, 2009, 8:35 PM
>
> Hi All,
>
> Well my 83 650 with 43K miles is rattling like a paint can at 2800 to
> 3300 rpm so it's time to deal with the automatic cam chain tensioner
> (or lack there of).
>
> I've studied all that the Honda OEM manual has to offer on this
> mechanism - so I know the pricipals by which it works but not any
> inspection criteria.
>
> I pulled the valve cover and this what i find:
>
> 1) No marks on the valve cover chain guard.
> 2) The cam chain was taught between the cam gears - I could push it
> 1/8" (total range of motion) when applying ~ 5 lbs downward and upward
> to the chain in between the gears, and the chain would retain whatever
> tension it had.
> 3) I pushed on the chain (same as in (3) above) with about 20 lbs and
> then it went slack with about 1/4" total range of motion up and down.
> I turned the engine 1/4 crank or so with the back wheel and the chain
> went back to the original tension as in (2)
> 4) The spring is connected to the mechanism (taught)
>
> That's about all I've observed at this stage.
>
> My question is: I
> Is there a definate way to diagnose the health of the tensioning
> system?
> Would the chain behaviour in (2) and (3) above be expected for a
> tensioner in good shape?
> Is there anything else i should inspect now before removal of the
> cams)
> How should a healthy tensioner behave during inspection?
>
> I was actually hoping I would find the tensioner arm magically
> "unstick" if i wiggled it but that may be a bit of a optimistic dream
> - right!
>
> Thanks for any suggestions you have.
>
> Paul
--~--~---------~--~----~------------~-------~--~----~
You received this message because you are subscribed to the Google Groups 
"Nighthawk Motorcycle Lovers!" group.
To post to this group, send email to [email protected]
To unsubscribe from this group, send email to 
[email protected]
For more options, visit this group at 
http://groups.google.com/group/nighthawk_lovers?hl=en
-~----------~----~----~----~------~----~------~--~---

Reply via email to