Parts are correct. Check for wear on guides /slippers. --- On Sun, 8/23/09, oldschoolgwin <[email protected]> wrote:
From: oldschoolgwin <[email protected]> Subject: [Nighthawk Lovers] Re: NH650 - Automatic cam chain tensioner inspection findings. To: "Nighthawk Motorcycle Lovers!" <[email protected]> Date: Sunday, August 23, 2009, 1:39 PM Dennis, Yes i do have the OEM manual. That's exactly right - i turned the engine a few revolutions and the chain is taught then loose (it must be from the different states of torque on the cams shafts). In the slack state the chain has about . 4" of vertical movement. Ok - I'm going to fix this. I'll just follow the Honda OEM manual to take the cams shafts out and replace the parts. I suspect if i don't find damage on the chain guides, and the chain has not strethed beyond spec, then i just need to purchase #3 in the link below which is P/N "Bracket, Tensioner 14500-ME5-030 (it includes the spring, the lower link the spring attaches to, and the spring tube). Does this sound right? It's $79. http://www.rosevillecyclecenter.com/fiche_section_detail.asp?section=123812&category=MOTORCYCLES&make=HONDA&year=1983&fveh=2958 Was there a factory recall to change these tensioners originally? Perhaps mine was never changed. Seems that a lot of 650's have this problem.. Thanks, Paul On Aug 22, 9:33 pm, Dennis Hammerl <[email protected]> wrote: > If you do really understand how it works, then go ahead and turn the > crankshaft (by hand, slowly) and watch what happens. There will be a place in > rotation (do it many times) where the cam chain will be quite slack. The > tension on it changes during rotation. Rotating the crankshaft backwards may > show the slack spot more easily. There was an update tensioner for '83 > models. All new parts supersede to the update. I would replace with the new > part and not attempt a repair of the original. It's a bear of a job but can > be done without making a real mess of the motor. Leave the cylinder head on. > Unless, of course you're replacing the cam chain too. You have the OEM manual > ? Good instructions for removal. The tensioner must be unloaded to be > removed. The manual does not address the dynamic of changing tensions during > running. The failed tensioner is not controlling the chain during a lightly > loaded situation. The spring isn't strong enough to work > properly. All these things are cured with the update. > > --- On Sat, 8/22/09, oldschoolgwin <[email protected]> wrote: > > From: oldschoolgwin <[email protected]> > Subject: [Nighthawk Lovers] NH650 - Automatic cam chain tensioner inspection > findings. > To: "Nighthawk Motorcycle Lovers!" <[email protected]> > Date: Saturday, August 22, 2009, 8:35 PM > > Hi All, > > Well my 83 650 with 43K miles is rattling like a paint can at 2800 to > 3300 rpm so it's time to deal with the automatic cam chain tensioner > (or lack there of). > > I've studied all that the Honda OEM manual has to offer on this > mechanism - so I know the pricipals by which it works but not any > inspection criteria. > > I pulled the valve cover and this what i find: > > 1) No marks on the valve cover chain guard. > 2) The cam chain was taught between the cam gears - I could push it > 1/8" (total range of motion) when applying ~ 5 lbs downward and upward > to the chain in between the gears, and the chain would retain whatever > tension it had. > 3) I pushed on the chain (same as in (3) above) with about 20 lbs and > then it went slack with about 1/4" total range of motion up and down. > I turned the engine 1/4 crank or so with the back wheel and the chain > went back to the original tension as in (2) > 4) The spring is connected to the mechanism (taught) > > That's about all I've observed at this stage. > > My question is: I > Is there a definate way to diagnose the health of the tensioning > system? > Would the chain behaviour in (2) and (3) above be expected for a > tensioner in good shape? > Is there anything else i should inspect now before removal of the > cams) > How should a healthy tensioner behave during inspection? > > I was actually hoping I would find the tensioner arm magically > "unstick" if i wiggled it but that may be a bit of a optimistic dream > - right! > > Thanks for any suggestions you have. > > Paul --~--~---------~--~----~------------~-------~--~----~ You received this message because you are subscribed to the Google Groups "Nighthawk Motorcycle Lovers!" group. To post to this group, send email to [email protected] To unsubscribe from this group, send email to [email protected] For more options, visit this group at http://groups.google.com/group/nighthawk_lovers?hl=en -~----------~----~----~----~------~----~------~--~---
