Sorry Dennis, the decimal point got lost in teh line return - that is
0.4" vertical range of motion at the worst case loose chain condition
when rotating the engine.

Tell me this isn't the worst case.

I'll read the Common Service manual as well.

If the tensioner is doing it's job, then there should be a constant
tension on the chain between the cam sprockets at any rotation -
perhaps such as the tight condition on mine that allows 1/8" travel
with a 5lb load normal to the chain.  Is this a correct assumption of
what a good tensioner should provide?

Thanks,

Paul

On Aug 23, 11:18 am, Dennis Hammerl <[email protected]> wrote:
> 4" of vert movement ? Between the cams ? unreal. Worst I've ever heard of.
> The tension is caused by how many valves are being operated which is why the 
> change as it's rotated. Chain replacement is an almost total tear-down. I can 
> make it a bit less of a hassle as I have a method that short-cuts the 
> process. I hate to take more apart than I have to, and I can save you some 
> time. I'll check out the site and get back to you. How talented are you ? 
> It's a great time to degree in the cams. The performance gain is well worth 
> the time spent. When removing parts, be very careful to return them to the 
> exact locations. Do not switch anything around because they are "all the 
> same" After all the miles, they have worn to fit each other. It's a kindness 
> to to restore all to original locations. Followers, adjusters, etc. The OEM 
> manual assumes you are familiar with procedures. Have you read the Common 
> Service Manual ? It's available on-line, free. A good read for all.
> The problem as found on first issue 650's was an update not a recall (there 
> is a difference) and repair was to be "as needed" Honda paid for repair of 
> defective parts for up to one year beyond warranty on a "good will" basis. 
>
> --- On Sun, 8/23/09, oldschoolgwin <[email protected]> wrote:
>
> From: oldschoolgwin <[email protected]>
> Subject: [Nighthawk Lovers] Re: NH650 - Automatic cam chain tensioner 
> inspection findings.
> To: "Nighthawk Motorcycle Lovers!" <[email protected]>
> Date: Sunday, August 23, 2009, 1:39 PM
>
> Dennis,
>
> Yes i do have the OEM manual.
>
> That's exactly right - i turned the engine a few revolutions and the
> chain is taught then loose (it must be from the different states of
> torque on the cams shafts).  In the slack state the chain has about .
> 4" of vertical movement.
>
> Ok - I'm going to fix this.  I'll just follow the Honda OEM manual to
> take the cams shafts out and replace the parts.
>
> I suspect if i don't find damage on the chain guides, and the chain
> has not strethed beyond spec, then i just need to purchase #3 in the
> link below which is P/N "Bracket, Tensioner 14500-ME5-030 (it includes
> the spring, the lower link the spring attaches to, and the spring
> tube).  Does this sound right?  It's $79.
>
> http://www.rosevillecyclecenter.com/fiche_section_detail.asp?section=...
>
> Was there a factory recall to change these tensioners originally?
> Perhaps mine was never changed. Seems that a lot of 650's have this
> problem..
>
> Thanks,
>
> Paul
>
> On Aug 22, 9:33 pm, Dennis Hammerl <[email protected]> wrote:
>
>
>
> > If you do really understand how it works, then go ahead and turn the 
> > crankshaft (by hand, slowly) and watch what happens. There will be a place 
> > in rotation (do it many times) where the cam chain will be quite slack. The 
> > tension on it changes during rotation. Rotating the crankshaft backwards 
> > may show the slack spot more easily.  There was an update tensioner for 
> > '83  models. All new parts supersede to the update. I would replace with 
> > the new part and not attempt a repair of the original. It's a bear of a job 
> > but can be done without making a real mess of the motor. Leave the cylinder 
> > head on. Unless, of course you're replacing the cam chain too. You have the 
> > OEM manual ?  Good instructions for removal. The tensioner must be unloaded 
> > to be removed. The manual does not address the dynamic of changing tensions 
> > during running. The failed tensioner is not controlling the chain during a 
> > lightly loaded situation. The spring isn't strong enough to work
> >  properly. All these things are cured with the update.
>
> > --- On Sat, 8/22/09, oldschoolgwin <[email protected]> wrote:
>
> > From: oldschoolgwin <[email protected]>
> > Subject: [Nighthawk Lovers] NH650 - Automatic cam chain tensioner 
> > inspection findings.
> > To: "Nighthawk Motorcycle Lovers!" <[email protected]>
> > Date: Saturday, August 22, 2009, 8:35 PM
>
> > Hi All,
>
> > Well my 83 650 with 43K miles is rattling like a paint can at 2800 to
> > 3300 rpm so it's time to deal with the automatic cam chain tensioner
> > (or lack there of).
>
> > I've studied all that the Honda OEM manual has to offer on this
> > mechanism - so I know the pricipals by which it works but not any
> > inspection criteria.
>
> > I pulled the valve cover and this what i find:
>
> > 1) No marks on the valve cover chain guard.
> > 2) The cam chain was taught between the cam gears - I could push it
> > 1/8" (total range of motion) when applying ~ 5 lbs downward and upward
> > to the chain in between the gears, and the chain would retain whatever
> > tension it had.
> > 3) I pushed on the chain (same as in (3) above) with about 20 lbs and
> > then it went slack with about 1/4" total range of motion up and down.
> > I turned the engine 1/4 crank or so with the back wheel and the chain
> > went back to the original tension as in (2)
> > 4) The spring is connected to the mechanism (taught)
>
> > That's about all I've observed at this stage.
>
> > My question is: I
> > Is there a definate way to diagnose the health of the tensioning
> > system?
> > Would the chain behaviour in (2) and (3) above be expected for a
> > tensioner in good shape?
> > Is there anything else i should inspect now before removal of the
> > cams)
> > How should a healthy tensioner behave during inspection?
>
> > I was actually hoping I would find the tensioner arm magically
> > "unstick" if i wiggled it but that may be a bit of a optimistic dream
> > - right!
>
> > Thanks for any suggestions you have.
>
> > Paul- Hide quoted text -
>
> - Show quoted text -
--~--~---------~--~----~------------~-------~--~----~
You received this message because you are subscribed to the Google Groups 
"Nighthawk Motorcycle Lovers!" group.
To post to this group, send email to [email protected]
To unsubscribe from this group, send email to 
[email protected]
For more options, visit this group at 
http://groups.google.com/group/nighthawk_lovers?hl=en
-~----------~----~----~----~------~----~------~--~---

Reply via email to