MichelinoK wrote: > Big-Cut :) > > >> Both outputs look sane - could you please post the output of these two >> commands as well: >> 2. ./boot_linux -F -d eth0 -i openwrt-etrax-jffs2-64k-fimage -p > > The output is this: > > [EMAIL PROTECTED] Desktop]# ./boot_linux -F -d eth0 -i > kamikaze/trunk/bin/openwrt-etrax-jffs2-64k-fimage -p > Command: > ./etrax100boot --device eth0 --setreg b0000000 000095a6 --setreg b0000004 > 00000104 --setreg b000000c 1a200040 --setreg b0000008 00005611 --setreg > b0000030 00001c00 --setreg b0000038 000000ff --file > kamikaze/trunk/bin/openwrt-etrax-jffs2-64k-fimage c0004000 --flash c0004000 > 0 800000 --jump 0 > [EMAIL PROTECTED] Desktop]# > >
Mine looks like this: $ boot_linux -d eth1 -F -i fimage -p Command: etrax100boot --device eth1 --setreg b0000000 000093f8 --setreg b0000004 00000204 --setreg b000000c 09603636 --setreg b0000008 8000c002 --pause 20000 --setreg b0000008 8000c602 --setreg b0000008 8000c002 --setreg +0 7 --label label1 --setreg b0000008 8000c402 --setreg b0000008 8000c002 --loop +0 label1 --setreg b0000008 8030c202 --setreg b0000008 8000c002 --setreg b0000008 80008002 --setreg b0000030 00000b00 --setreg b0000038 0000fed3 --file fimage c0004000 --flash c0004000 0 400000 --jump 0 Judging from the output my flash command is a bit longer, now I haven't looked at the commands switches in detail, but you might missing bits on your hardware to see if it helps. > (2 commands? I can see only one command :) Just one, my bad ;) > Found 1 x CFI at 0x80000000 > No single x16 at 0x84000000 > No interleaved x16 at 0x84000000 > 0x80000000: No need to write > 0x80010000: No need to write > 0x80020000: No need to write > 0x80030000: No need to write > 0x80040000: No need to write > > Cut > > 0x807f6000: No need to write > 0x807f8000: No need to write > 0x807fa000: No need to write > 0x807fc000: No need to write > 0x807fe000: No need to write > 0x80000000: Verifying...OK > JUMP > 0x00000000 > END > Exiting with code 0 > [EMAIL PROTECTED] Desktop]# > > Now that is strange - I always experienced the replacement of flash content when using different images. You might get some more help from acme or axis mailing lists in this case. > > Please, can you try a simple image created with kamikaze? Just to know if it > works on other hardware. I'll give it a try. Regards, Hinko -- ČETRTA POT, d.o.o., Kranj Planina 3 4000 Kranj Slovenia, Europe Tel. +386 (0) 4 280 66 03 E-mail: [EMAIL PROTECTED] Http: www.cetrtapot.si _______________________________________________ openwrt-devel mailing list openwrt-devel@lists.openwrt.org http://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
