Bill,
I think you misunderstood what everyone has been saying. You can't import
the Tango schematic with any Protel tool. You can import the PCB with
Protel 2.8, then save it in ASCII format and import it into any of the
newer Protel versions. You can directly import the Tango netlist into any
newer Protel version without pre-processing.
Been there... tried all of that.
Regards - Harry
At 08:56 AM 9/23/05, you wrote:
The first few lines in the schematic ASCII file read
;Tango-Schematic 1.50 Series II
TANGO_SCHEMATIC 1 1 A
SHEET 0 0 17000 11000 2
SIZE 344 317 14959 9433 344 317
JUNC 7875 5225
JUNC 7975 3225
JUNC 4675 4475
JUNC 3400 4000
I have not tried PCAD because I don't have a copy of PCAD here to experiment
with... I do have Protel 2.8 though and we might try importing with that...
Bill Brooks - KG6VVP
PCB Design Engineer, C.I.D.+, C.I.I.
Tel: (760)597-1500 Ext 3772 Fax: (760)597-1510
Datron World Communications, Inc.
_______________________________________
San Diego Chapter of the IPC Designers Council
Communications Officer, Web Manager
http://dcchapters.ipc.org/SanDiego/
http://pcbwizards.com
-----Original Message-----
From: PCB Designs [mailto:[EMAIL PROTECTED]
Sent: Friday, September 23, 2005 4:29 AM
To: Protel EDA Discussion List
Subject: Re: [PEDA] Conversion from TANGO SCHEMATIC to PROTEL???
Abd ulRahman,
>>Anyone know how to import a schematic from TANGO SCH to Protel?
>>Also, how about from TANGO PCB to Protel?
> I know of no way to convert Tango SCH. We can do Tango design if
> necessary. I think. It has been quite a while.
> Tango PCB can be imported into Protel using Protel 2.8. I did it quite a
> few times.
I think Bill also has PCad 2K, so there is a possibility here.
PCad2K also imports Tango PCBs, even better than Protel 2.8 (on polygons).
PCad2K also imports Tango ASCII schematics, the trick here is to have the
complete Tango schematic library, then you have to use Library Executive to
import the Tango Library to the PCad format, setup the library in the PCad
schematic program, and then import the Tango schematic.
Hope this helps.
Best Regards,
Paulo Egon
____________________________________________________________
You are subscribed to the PEDA discussion forum
To Post messages:
mailto:[email protected]
Unsubscribe and Other Options:
http://techservinc.com/mailman/listinfo/peda_techservinc.com
Browse or Search Old Archives (2001-2004):
http://www.mail-archive.com/[email protected]
Browse or Search Current Archives (2004-Current):
http://www.mail-archive.com/[email protected]
____________________________________________________________
You are subscribed to the PEDA discussion forum
To Post messages:
mailto:[email protected]
Unsubscribe and Other Options:
http://techservinc.com/mailman/listinfo/peda_techservinc.com
Browse or Search Old Archives (2001-2004):
http://www.mail-archive.com/[email protected]
Browse or Search Current Archives (2004-Current):
http://www.mail-archive.com/[email protected]
____________________________________________________________
You are subscribed to the PEDA discussion forum
To Post messages:
mailto:[email protected]
Unsubscribe and Other Options:
http://techservinc.com/mailman/listinfo/peda_techservinc.com
Browse or Search Old Archives (2001-2004):
http://www.mail-archive.com/[email protected]
Browse or Search Current Archives (2004-Current):
http://www.mail-archive.com/[email protected]
