Thanks Harry, I get it.
I just wasn't complete in expressing my thought... I meant 'try importing the PCB file', as I did read that the schematic file does not directly convert. I just grabbed the .s01 file and opened it with notepad to show what version of the program it was created with... Now I realize that there really isn't a correlation between the PCB program and the Schematic program like in the newer Protel versions because the two programs evolved separately. So establishing the version that way was pointless. It may be quicker to just 'bite the bullet' and redo the schematic in Protel. I realize the netlist will probably import into Protel PCB without any trouble... the netlist formats look identical. Thanks, Bill Brooks - KG6VVP PCB Design Engineer, C.I.D.+, C.I.I. Tel: (760)597-1500 Ext 3772 Fax: (760)597-1510 Datron World Communications, Inc. _______________________________________ San Diego Chapter of the IPC Designers Council Communications Officer, Web Manager http://dcchapters.ipc.org/SanDiego/ http://pcbwizards.com -----Original Message----- From: Harry Selfridge [mailto:[EMAIL PROTECTED] Sent: Friday, September 23, 2005 9:52 AM To: Protel EDA Discussion List Subject: RE: [PEDA] Conversion from TANGO SCHEMATIC to PROTEL??? Bill, I think you misunderstood what everyone has been saying. You can't import the Tango schematic with any Protel tool. You can import the PCB with Protel 2.8, then save it in ASCII format and import it into any of the newer Protel versions. You can directly import the Tango netlist into any newer Protel version without pre-processing. Been there... tried all of that. Regards - Harry At 08:56 AM 9/23/05, you wrote: >The first few lines in the schematic ASCII file read > >;Tango-Schematic 1.50 Series II >TANGO_SCHEMATIC 1 1 A >SHEET 0 0 17000 11000 2 >SIZE 344 317 14959 9433 344 317 >JUNC 7875 5225 >JUNC 7975 3225 >JUNC 4675 4475 >JUNC 3400 4000 > > >I have not tried PCAD because I don't have a copy of PCAD here to experiment >with... I do have Protel 2.8 though and we might try importing with that... > > >Bill Brooks - KG6VVP >PCB Design Engineer, C.I.D.+, C.I.I. >Tel: (760)597-1500 Ext 3772 Fax: (760)597-1510 >Datron World Communications, Inc. >_______________________________________ >San Diego Chapter of the IPC Designers Council >Communications Officer, Web Manager >http://dcchapters.ipc.org/SanDiego/ >http://pcbwizards.com >-----Original Message----- >From: PCB Designs [mailto:[EMAIL PROTECTED] >Sent: Friday, September 23, 2005 4:29 AM >To: Protel EDA Discussion List >Subject: Re: [PEDA] Conversion from TANGO SCHEMATIC to PROTEL??? > >Abd ulRahman, > > > >>Anyone know how to import a schematic from TANGO SCH to Protel? > >>Also, how about from TANGO PCB to Protel? > > I know of no way to convert Tango SCH. We can do Tango design if > > necessary. I think. It has been quite a while. > > Tango PCB can be imported into Protel using Protel 2.8. I did it quite a > > few times. > >I think Bill also has PCad 2K, so there is a possibility here. >PCad2K also imports Tango PCBs, even better than Protel 2.8 (on polygons). >PCad2K also imports Tango ASCII schematics, the trick here is to have the >complete Tango schematic library, then you have to use Library Executive to >import the Tango Library to the PCad format, setup the library in the PCad >schematic program, and then import the Tango schematic. >Hope this helps. > >Best Regards, >Paulo Egon > > > > >____________________________________________________________ >You are subscribed to the PEDA discussion forum > >To Post messages: >mailto:[email protected] > >Unsubscribe and Other Options: >http://techservinc.com/mailman/listinfo/peda_techservinc.com > >Browse or Search Old Archives (2001-2004): >http://www.mail-archive.com/[email protected] > >Browse or Search Current Archives (2004-Current): >http://www.mail-archive.com/[email protected] > > >____________________________________________________________ >You are subscribed to the PEDA discussion forum > >To Post messages: >mailto:[email protected] > >Unsubscribe and Other Options: >http://techservinc.com/mailman/listinfo/peda_techservinc.com > >Browse or Search Old Archives (2001-2004): >http://www.mail-archive.com/[email protected] > >Browse or Search Current Archives (2004-Current): >http://www.mail-archive.com/[email protected] ____________________________________________________________ You are subscribed to the PEDA discussion forum To Post messages: mailto:[email protected] Unsubscribe and Other Options: http://techservinc.com/mailman/listinfo/peda_techservinc.com Browse or Search Old Archives (2001-2004): http://www.mail-archive.com/[email protected] Browse or Search Current Archives (2004-Current): http://www.mail-archive.com/[email protected] ____________________________________________________________ You are subscribed to the PEDA discussion forum To Post messages: mailto:[email protected] Unsubscribe and Other Options: http://techservinc.com/mailman/listinfo/peda_techservinc.com Browse or Search Old Archives (2001-2004): http://www.mail-archive.com/[email protected] Browse or Search Current Archives (2004-Current): http://www.mail-archive.com/[email protected]
