Hi Ridgh, In fact it might be best to do this all within Altium Designer, and not go back to 99SE, as certain features may not be fully backwards compatible. Solid polygons, and split plane editing are at least two areas that have changed. Believe some new design rules were added in AD too.
Usually any newer objects will be ignored and/or lost when one goes back to a previous version where those features did not exist. ---Phil Wednesday, June 27, 2007, 3:14:30 PM, you wrote: > Ridgh, > You don't need to convert the files back to Protel. > You can generate the gerbers out of the Altium > Designer PCB file. > If things are messed up, probably the apertures are > wrong or missing. > Mira > --- Ridgh <[EMAIL PROTECTED]> wrote: >> Hello again, >> First, I'd like to thank you very much for your >> response. >> In any case, the only way I found was to convert the >> files to the old >> Protel 99 .PCB format, and then to export them with >> the extensions GBL, GTL, >> GTO, GBO,.. But checking them with the Camtastic, >> all I saw on my monitor >> was a very distorted "draw" - and not the Gerber as >> I knew before. >> In any case I'd like to thank you again, >> Ridgh >> >> >> -----Original Message----- >> From: Mira [mailto:[EMAIL PROTECTED] >> Sent: Wednesday, June 27, 2007 5:06 PM >> To: Protel EDA Discussion List >> Subject: Re: [PEDA] Need help to convert .pcbdoc to >> Gerber files >> >> Ridgh, >> >> If you've managed to generate the gerbers, they are >> probably saved on your >> hard drive. Look for file names as your PCB and >> extensions GBL, GTL, GTO, >> GBO.. >> They are automatically open in Camtastic, which is >> the gerber viewer. >> If you like to save them from there, you have to use >> File/Export gerber (not >> File/Save). >> >> To generate the drill file look for NC Drill files. >> The drill file normally has DRL extension but in >> Altium designer it's TXT. >> >> I'm not sure how the output files are set & >> generated in DXP-2004 version >> but to do this in Altium Designer >> 6.7 you have to create an output job file and run >> the batch from there. >> >> Mira >> >> --- Ridgh <[EMAIL PROTECTED]> wrote: >> >> > Hello, >> > I need very much your help: >> > I am relative newbie in PCB production. >> > At my new workplace is installed Protel DXP 2004. >> > Usually I use to draw 1 >> > layer PCBs and sometimes 2 layers. The output >> files I'm getting are >> > .PcbDoc files. >> > I've been asked to send for production Gerber >> files, so I've tried the >> > option Export->Gerber. It opened another window, >> named "Camtastic" and >> > got a file with the .CAM . >> > The problem is that any PCB manufacturer I've >> asked doesn't know this >> > format, so, as I assume that you are the >> professional ones, I'll be >> > very thankful for your help. >> > How can I convert it to Gerber files? All I need >> is a top, mechanical, >> > solder mask and drilling layers. >> > Thank you in advance, >> > Ridgh >> > >> > >> > >> > ____________________________________________________________ >> > You are subscribed to the PEDA discussion forum >> > >> > To Post messages: >> > mailto:[email protected] >> > >> > Unsubscribe and Other Options: >> > >> > http://techservinc.com/mailman/listinfo/peda_techservinc.com >> > >> > Browse or Search Old Archives (2001-2004): >> > >> > http://www.mail-archive.com/[EMAIL PROTECTED] >> > >> > Browse or Search Current Archives (2004-Current): >> > http://www.mail-archive.com/[email protected] >> > >> > >> >> >> >> >> > ____________________________________________________________________________ >> ________ >> Be a better Heartthrob. Get better relationship >> answers from someone who >> knows. Yahoo! Answers - Check it out. >> > http://answers.yahoo.com/dir/?link=list&sid=396545433 >> >> >> > ____________________________________________________________ >> You are subscribed to the PEDA discussion forum >> >> To Post messages: >> mailto:[email protected] >> >> Unsubscribe and Other Options: >> > http://techservinc.com/mailman/listinfo/peda_techservinc.com >> >> Browse or Search Old Archives (2001-2004): >> > http://www.mail-archive.com/[EMAIL PROTECTED] >> >> Browse or Search Current Archives (2004-Current): >> http://www.mail-archive.com/[email protected] >> >> >> >> >> >> > ____________________________________________________________ >> You are subscribed to the PEDA discussion forum >> >> To Post messages: >> mailto:[email protected] >> >> Unsubscribe and Other Options: >> > http://techservinc.com/mailman/listinfo/peda_techservinc.com >> >> Browse or Search Old Archives (2001-2004): >> > http://www.mail-archive.com/[EMAIL PROTECTED] >> >> Browse or Search Current Archives (2004-Current): >> http://www.mail-archive.com/[email protected] >> >> > > ____________________________________________________________________________________ > Moody friends. Drama queens. Your life? Nope! - their life, your > story. Play Sims Stories at Yahoo! Games. > http://sims.yahoo.com/ > > ____________________________________________________________ > You are subscribed to the PEDA discussion forum > To Post messages: > mailto:[email protected] > Unsubscribe and Other Options: > http://techservinc.com/mailman/listinfo/peda_techservinc.com > Browse or Search Old Archives (2001-2004): > http://www.mail-archive.com/[EMAIL PROTECTED] > > Browse or Search Current Archives (2004-Current): > http://www.mail-archive.com/[email protected] ____________________________________________________________ You are subscribed to the PEDA discussion forum To Post messages: mailto:[email protected] Unsubscribe and Other Options: http://techservinc.com/mailman/listinfo/peda_techservinc.com Browse or Search Old Archives (2001-2004): http://www.mail-archive.com/[EMAIL PROTECTED] Browse or Search Current Archives (2004-Current): http://www.mail-archive.com/[email protected]
