The waves stuff does have some RTAS  plugs as well, however they
aren't very accessible atleast with out mapping the control to a
control surface  from what i have read on here. However From what i
understand the Izotope stuff should be VO friendly  and Izotope said
that do do some basic VO testing with all their Plugs now and welcome
feedback. Nectar is their vocal channel strip, alloy is there general
purpose channel strip, and ozone is their mastering oriented channel
strip. I believe there should be free demos on the www.izotope.com
site to check out. Been meaning to check these out and post my
experiences myself, but working on  mastering editing with PT before i
get back into mixing again so haven't gotten around to it yet. Post
your experiences please if you try them before i do.

On 10/16/11, Gordon Kent <[email protected]> wrote:
> Are there any good channel strip plugs that will work with VO and PT.  It
> seems that most of the waves stuff is for native setups, but maybe I have
> that wrong.  I would just like to get something better than the stock eq's
> and compressor.  The factory plug-ins have been around since pt6 and maybe
> earlier than that.  The bomb factory compressor is a bit better, but it
> would be nice to have a strip with comp/eq/tube distortion etc.
> Gord
>
> -----Original Message-----
> From: Slau Halatyn
> Sent: Sunday, October 16, 2011 11:20 AM
> To: [email protected]
> Subject: Re: Master Tracks?
>
> No worries, I didn't take it that way at all. It's definitely an aspect of
> using the master track that one should consider. At this point, I think the
> issue of pre versus post fader compression is beyond the question when
> someone is just trying to get their head around Pro Tools in general,
> that'sl all.
>
> Cheers,
>
> Slau
>
> On Oct 16, 2011, at 11:03 AM, Stephen Martin wrote:
>
>> I do agree with you, and i do apologize if i came off as trying to correct
>>
>> you or saying you shouldn't put a compressor on the master track. It was
>> intended more as a suggestion or tip that i came across  in my own journey
>>
>> in learning more about PT, and figured i'd would share another way of
>> doing it with the list.
>> On Oct 16, 2011, at 10:49 AM, Slau Halatyn wrote:
>>
>>> As with most things, there's more than one way to accomplish a task and
>>> this is one of them. Some people put compressors on the master track,
>>> some don't. I'm simply illustrating one of its uses.
>>>
>>> Slau
>>>
>>> On Oct 16, 2011, at 10:02 AM, Stephen Martin wrote:
>>>
>>>> I have read in a few  places where they don't always recommend putting a
>>>>
>>>> master compressor on the master track, since the master track unlike all
>>>>
>>>> the other tracks in pro tools has the fader before the inserts and
>>>> sends, which means if u put a compressor on the master track, set it up
>>>> how u like, then later adjust the master fader, it will pretty much
>>>> cause you to have to go redo the compressor settings. A work around is
>>>> to create a sub mimix aux track and send all your tracks to that, add
>>>> all your master effects on that track and output that to the master
>>>> track.
>>>>
>>>> On Oct 16, 2011, at 9:54 AM, Slau Halatyn wrote:
>>>>
>>>>> Christopher,
>>>>>
>>>>> Master tracks control the output level being fed to an output bus. Most
>>>>>
>>>>> often, a master track will control the main left and right outputs for
>>>>> a stereo mix. It's not necessary to necessarily use a master track for
>>>>> a regular mix but it certainly does help to create a master track to
>>>>> see the combined level of all of the individual tracks on the master
>>>>> track's level meter. Further, when putting bus compression over an
>>>>> entire mix, it would normally be done with a compressor plug-in on a
>>>>> master track. Finally, master tracks are used when creating stems for
>>>>> surround mixes, alternate mixes, instrumental versions, etc. Again,
>>>>> most people just use a single master track for overall mix purposes.
>>>>>
>>>>> HTH,
>>>>>
>>>>> Slau
>>>>>
>>>>>
>>>>
>>>
>>
>

Reply via email to