Re: [Elecraft] WSJT-X Disabling TX INHIBIT on K3S
Tom, I was told that. All I can say is that there is no delay from the K3S when I transmit on WSJT-X. I increased the delay to .3 seconds under ADVANCED in WSJT-X settings and the problem is solved. 73, John WA!EAZ > On Nov 13, 2018, at 11:12 PM, Tom wrote: > > Hi, > WSJT-X does not touch TX Inhibit. > The only command that WSJT-X sends is a TX; command to enter transmit mode or > it asserts DTR or RTS. The same is true for Yaesu and Icom transceivers. Now > if the radio does this itself behind the scenes, that is another story. But > 100% for sure WSJT-X does not send the TX inhibit menu command. > 73 Tom > va2fsq.com > > > -Original Message- From: John Stengrevics > Sent: Tuesday, November 13, 2018 2:35 PM > To: Elecraft Reflector > Subject: [Elecraft] WSJT-X Disabling TX INHIBIT on K3S > > I asked this question previously and was told that the WSJT-X would not > effect TX INHIBIT on the K3S. > > In trying to confirm this just now, TX INHIBIT is clearly disabled when I > call CQ on FT8 digital mode. > > Any thoughts? > > John > WA1EAZ > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to tom...@videotron.ca > > --- > This email has been checked for viruses by Avast antivirus software. > https://www.avast.com/antivirus > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] Bluetooth Headphones for CW
Good morning all, Skip to the last paragraph to get the question. I operate almost exclusively on CW with a KX3 and K2 that I built in 2004. I have the audio from two computers and both radios run to a small Xenyx 502 mixer , then to a small stereo amp and a nice pair of speakers. I seldom use the speakers and I run a couple of pairs of corded headphones from the mixer. I often run afoul of the headphone cord. It gets tangled in the arm of my chair, etc... I would love to have wireless, noise cancelling headphones. However, this would involve putting a bluetooth (or other wireless) transmitter on the mixer output, compatible with whichever model of headphones I buy. The big issue (as far as I can understand it) is Latency. The CW sidetone must not be delayed. I have googled latency specs and found some pretty good data for headphones. I found at least one pair of headphones that measures 40ms latency, a number that would probably work. However, that doesn't include the latency induced by the transmitter. Is anyone using a transmitter/headphone combination for CW that works? If so, please share your setup details. Thanks. Dave, K4TO __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] Possible K3s TX failure - distorted audio
Well here we are two weeks later. The radio's been sitting in the repair queue since Nov. 1st and hasn't even been looked at yet according to the phone call I just placed. Still waiting to experience that legendary Elecraft support that everybody here raves about. To have a radio that I went four years into debt to buy fail catastrophically after two years of extremely light use isn't something I signed up for. Sorry for venting, but I basically lost a chance at setting a personal best in CQWW-SSB and now CW seems out of the question too, although thankfully a loaned Flex 6500 has at least kept me on the air. Regards, Peter Dougherty, W2IRT -Original Message- From: elecraft-boun...@mailman.qth.net [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Gary Smith Sent: Sunday, October 28, 2018 8:58 PM To: Elecraft@mailman.qth.net Subject: Re: [Elecraft] Possible K3s TX failure - distorted audio Peter, I had that issue with the K3s, same kind of issue. I'd sent it in maybe 3 months ago for some warranty work & work on the PA I believe it was, but hadn't used the SSB for the same reasons as you. I heard no issue in the headphones listening to Monitor but got many reports of a terrible signal. I bought a HM4 mic thinking that was the issue but the new mic did no better. I ran the backup K3 and got excellent reports with the KM4 mic so knew the issue was in the K3s. It's in California, in Queue right now. Your issue may be different. 73, Gary KA1J > Hi all. > Early into CQWW this weekend I was getting reports of extremely > distorted audio from my K3s. Being mostly a CW (and 6m FT8) operator I > wasn't sure what was going on. I figured it was RF, but it was > happening at all power levels, from QRP to 100W, and QRO with my > KPA-1500. Same (bad) audio, just stronger/weaker signals. All bands > were equally bad. > > I ended up going from the radio directly to the tower, physically > bypassing the amp and tuner, and only running low power, with the same > result. It sounded more like distorted audio than RF ingress. > > Some troubleshooting by Dave, WO2X, who is a Flex owner: He remoted in > to his Flex a few miles away and noticed my garbled signal was > absolutely dirty and wide, despite low mic gain and little or no > compression. The audio sounded clean through the monitor, so it wasn't > the audio chain. He's speculating I may have a blown FET in the PA > stage. > > We put in a Flex 6500 temporarily and it seems to be running fine. > Wondering if anybody here has had experience with this, and if so, > what are my next steps? > > Thanks in advance. > > - > 73 and Good DX > Peter, W2IRT > > K3s S/N 10023 > > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to g...@ka1j.com > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to li...@w2irt.net __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] Possible K3s TX failure - distorted audio
I think it is possible that those who are happy with Elecraft legendary support are the same people that have realistic expectations. Marv KG7V -Original Message- From: elecraft-boun...@mailman.qth.net On Behalf Of Peter Dougherty (W2IRT) Sent: Wednesday, November 14, 2018 2:14 PM To: g...@ka1j.com; Elecraft@mailman.qth.net Subject: Re: [Elecraft] Possible K3s TX failure - distorted audio Well here we are two weeks later. The radio's been sitting in the repair queue since Nov. 1st and hasn't even been looked at yet according to the phone call I just placed. Still waiting to experience that legendary Elecraft support that everybody here raves about. To have a radio that I went four years into debt to buy fail catastrophically after two years of extremely light use isn't something I signed up for. Sorry for venting, but I basically lost a chance at setting a personal best in CQWW-SSB and now CW seems out of the question too, although thankfully a loaned Flex 6500 has at least kept me on the air. Regards, Peter Dougherty, W2IRT -Original Message- From: elecraft-boun...@mailman.qth.net [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Gary Smith Sent: Sunday, October 28, 2018 8:58 PM To: Elecraft@mailman.qth.net Subject: Re: [Elecraft] Possible K3s TX failure - distorted audio Peter, I had that issue with the K3s, same kind of issue. I'd sent it in maybe 3 months ago for some warranty work & work on the PA I believe it was, but hadn't used the SSB for the same reasons as you. I heard no issue in the headphones listening to Monitor but got many reports of a terrible signal. I bought a HM4 mic thinking that was the issue but the new mic did no better. I ran the backup K3 and got excellent reports with the KM4 mic so knew the issue was in the K3s. It's in California, in Queue right now. Your issue may be different. 73, Gary KA1J > Hi all. > Early into CQWW this weekend I was getting reports of extremely > distorted audio from my K3s. Being mostly a CW (and 6m FT8) operator I > wasn't sure what was going on. I figured it was RF, but it was > happening at all power levels, from QRP to 100W, and QRO with my > KPA-1500. Same (bad) audio, just stronger/weaker signals. All bands > were equally bad. > > I ended up going from the radio directly to the tower, physically > bypassing the amp and tuner, and only running low power, with the same > result. It sounded more like distorted audio than RF ingress. > > Some troubleshooting by Dave, WO2X, who is a Flex owner: He remoted in > to his Flex a few miles away and noticed my garbled signal was > absolutely dirty and wide, despite low mic gain and little or no > compression. The audio sounded clean through the monitor, so it wasn't > the audio chain. He's speculating I may have a blown FET in the PA > stage. > > We put in a Flex 6500 temporarily and it seems to be running fine. > Wondering if anybody here has had experience with this, and if so, > what are my next steps? > > Thanks in advance. > > - > 73 and Good DX > Peter, W2IRT > > K3s S/N 10023 > > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net Please help support this email > list: http://www.qsl.net/donate.html Message delivered to > g...@ka1j.com > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to li...@w2irt.net __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to marvwhee...@nwlink.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] Possible K3s TX failure - distorted audio
The current stated turnaround time for Elecraft repairs is 3 to 4 weeks. Given the staff techs with experience, that is the best that they can do. Oh, yes, "hire more techs" can be said, but that takes time away from those techs now working on repairs for training of new people, so initially the backlog increases until the new techs come on board. Not an easy problem to solve for a small company. 73, Don W3FPR On 11/14/2018 7:26 PM, marvwhee...@nwlink.com wrote: I think it is possible that those who are happy with Elecraft legendary support are the same people that have realistic expectations. Marv KG7V -Original Message- From: elecraft-boun...@mailman.qth.net On Behalf Of Peter Dougherty (W2IRT) Sent: Wednesday, November 14, 2018 2:14 PM To: g...@ka1j.com; Elecraft@mailman.qth.net Subject: Re: [Elecraft] Possible K3s TX failure - distorted audio Well here we are two weeks later. The radio's been sitting in the repair queue since Nov. 1st and hasn't even been looked at yet according to the phone call I just placed. Still waiting to experience that legendary Elecraft support that everybody here raves about. To have a radio that I went four years into debt to buy fail catastrophically after two years of extremely light use isn't something I signed up for. Sorry for venting, but I basically lost a chance at setting a personal best in CQWW-SSB and now CW seems out of the question too, although thankfully a loaned Flex 6500 has at least kept me on the air. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] K3 Parts for Sale
Please contact me direct with an offer if you are interested in any of these K3 parts. 2.7k Filter -- KXV3-2 Rev A board The next three go together: -- KIO3 REMOTE I/O REV B KIO3 AUDIO IO MODULE REV XD KIO3 MAIN REV A --- KSYN3 REV A SUB RCV --- KSYN3 REV A MAIN RCV --- KANT3 ANTENNA INPUT MODULE (this is the card needed when you do not have the auto tuner) Rich K3RWN __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] Possible K3s TX failure - distorted audio
Pete et al: I purchased my K3S 100-F in August of 2015. I experienced a failure in the form of distorted SSB audio in April 2018. Working with the techs at Elecraft they suggested and supplied a new KPA3A. That unit was received and installed and failed within a week. They then suggested the radio be returned for repair. It was shipped to Elecraft on May 8, 2018 and received at Elecraft on May 10, 2018. I shipped by USPS Priority Mail. It was repaired, updated and completely aligned and shipped to me on May 31, 2018. At the time I obtained my RA, the repair time was given as 15 to 20 working days. The radio was received by me on June 7, 2018 as it was shipped via UPS Ground. That overall project covers a span of 30 days or so. All seemed reasonable to me considering repair time and shipping time both ways. 73 Bob, K4TAX On 11/14/2018 4:13 PM, Peter Dougherty (W2IRT) wrote: Well here we are two weeks later. The radio's been sitting in the repair queue since Nov. 1st and hasn't even been looked at yet according to the phone call I just placed. Still waiting to experience that legendary Elecraft support that everybody here raves about. To have a radio that I went four years into debt to buy fail catastrophically after two years of extremely light use isn't something I signed up for. Sorry for venting, but I basically lost a chance at setting a personal best in CQWW-SSB and now CW seems out of the question too, although thankfully a loaned Flex 6500 has at least kept me on the air. Regards, Peter Dougherty, W2IRT __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] Possible K3s TX failure - distorted audio
The biggest repair queue delay we get this time of year is when we receive an unexpected block of lightning damaged radios. That usually adds a couple of weeks to the repair queue. (We can easily determine where the lightning activity is around the country from the return addresses..) Don't forget to disconnect ALL cables from your radios, amps etc when lightning is near. We frequently see damage when the cables between the radio and computer are left connected. Nearby lightning strikes have a way of finding ground via almost any odd path. 73, Eric /elecraft.com/ On 11/14/2018 4:38 PM, Don Wilhelm wrote: The current stated turnaround time for Elecraft repairs is 3 to 4 weeks. Given the staff techs with experience, that is the best that they can do. Oh, yes, "hire more techs" can be said, but that takes time away from those techs now working on repairs for training of new people, so initially the backlog increases until the new techs come on board. Not an easy problem to solve for a small company. 73, Don W3FPR On 11/14/2018 7:26 PM, marvwhee...@nwlink.com wrote: I think it is possible that those who are happy with Elecraft legendary support are the same people that have realistic expectations. Marv KG7V -Original Message- From: elecraft-boun...@mailman.qth.net On Behalf Of Peter Dougherty (W2IRT) Sent: Wednesday, November 14, 2018 2:14 PM To: g...@ka1j.com; Elecraft@mailman.qth.net Subject: Re: [Elecraft] Possible K3s TX failure - distorted audio Well here we are two weeks later. The radio's been sitting in the repair queue since Nov. 1st and hasn't even been looked at yet according to the phone call I just placed. Still waiting to experience that legendary Elecraft support that everybody here raves about. To have a radio that I went four years into debt to buy fail catastrophically after two years of extremely light use isn't something I signed up for. Sorry for venting, but I basically lost a chance at setting a personal best in CQWW-SSB and now CW seems out of the question too, although thankfully a loaned Flex 6500 has at least kept me on the air. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to eric.swa...@elecraft.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] Possible K3s TX failure - distorted audio
I don't remember any brand doing it much better... Chuck KE9UW c-haw...@illinois.edu Sent from my iPad > On Nov 14, 2018, at 6:39 PM, Don Wilhelm wrote: > > The current stated turnaround time for Elecraft repairs is 3 to 4 weeks. > Given the staff techs with experience, that is the best that they can do. > Oh, yes, "hire more techs" can be said, but that takes time away from those > techs now working on repairs for training of new people, so initially the > backlog increases until the new techs come on board. > Not an easy problem to solve for a small company. > > 73, > Don W3FPR > >> On 11/14/2018 7:26 PM, marvwhee...@nwlink.com wrote: >> I think it is possible that those who are happy with Elecraft legendary >> support are the same people that have realistic expectations. >> Marv >> KG7V >> -Original Message- >> From: elecraft-boun...@mailman.qth.net On >> Behalf Of Peter Dougherty (W2IRT) >> Sent: Wednesday, November 14, 2018 2:14 PM >> To: g...@ka1j.com; Elecraft@mailman.qth.net >> Subject: Re: [Elecraft] Possible K3s TX failure - distorted audio >> Well here we are two weeks later. The radio's been sitting in the repair >> queue since Nov. 1st and hasn't even been looked at yet according to the >> phone call I just placed. Still waiting to experience that legendary >> Elecraft support that everybody here raves about. To have a radio that I >> went four years into debt to buy fail catastrophically after two years of >> extremely light use isn't something I signed up for. Sorry for venting, but >> I basically lost a chance at setting a personal best in CQWW-SSB and now CW >> seems out of the question too, although thankfully a loaned Flex 6500 has at >> least kept me on the air. > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to c-haw...@illinois.edu __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] Possible K3s TX failure - distorted audio
Seems about right. My K3 arrived in Watsonville on Oct 1, and was shipped back exactly 30 days later. That said, it was the first time my nearly 10-year-old K3 had been back to the factory and the first actual problem of any kind I’d had with it. At the same time, they installed the front panel board gold pins (which may have been the actual cause of the problem I was having), put a mod in the KPA3, added a bracket, aligned it, and checked it. I’d been sitting on a set of those gold pins for quite a while in my “when I get a Round To-It” box of parts, and it’s probably too bad I hadn’t taken the time to put them in before some oxidation caused a problem. At least it’s done now, and I know my radio still meets or exceeds specs. 30 days was a small price to pay … even though it was a lonely time :-) Grant NQ5T K3 #2091 KX3 #8342 >> >> >> >> The current stated turnaround time for Elecraft repairs is 3 to 4 weeks. >> 73, >> Don W3FPR __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] Possible K3s TX failure - distorted audio
Good techs don’t come cheap, either, which increases overhead and inflates prices. Patience works to everyone’s benefit. Kent K9ZTV > On Nov 14, 2018, at 7:38 PM, Don Wilhelm wrote: > > The current stated turnaround time for Elecraft repairs is 3 to 4 weeks. > Given the staff techs with experience, that is the best that they can do. > Oh, yes, "hire more techs" can be said, but that takes time away from those > techs now working on repairs for training of new people, so initially the > backlog increases until the new techs come on board. > Not an easy problem to solve for a small company. > > 73, > Don W3FPR > >> >> Well here we are two weeks later. The radio's been sitting in the repair >> queue since Nov. 1st and hasn't even been looked at yet according to the >> phone call I just placed. Still waiting to experience that legendary >> Elecraft support that everybody here raves about. To have a radio that I >> went four years into debt to buy fail catastrophically after two years of >> extremely light use isn't something I signed up for. Sorry for venting, but >> I basically lost a chance at setting a personal best in CQWW-SSB and now CW >> seems out of the question too, although thankfully a loaned Flex 6500 has at >> least kept me on the air. > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to k9...@socket.net > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] Set up Problems on WSJT/FT8 with Elecraft K3/0 Mini using RRC 1258 MKII
This set up has been working without problems for several weeks. Then CAT connection problems began. Audio is received and decoded, the K3/0 can control the radio, however When WSJT is started, the familiar ³Rig Control error² dialog box appears. In the Settings Menu under Radio, It does NOT pass the CAT Test. I¹ve checked the ports and the port we are using is assigned to the RRC unit. Settings are COM6, Baud rate: 38400; Data Bits: Eight; Stop Bits: one; Handshake: None; PTT Method; CAT; Port; USB (this seems to be my only choice in the dip down menu); Mode; USB; Split operation: Fake it. I played around with a number of these also trying other ports. Software Version 1.9.1; Does anyone have suggestions. 73 Dave K1KA Dave Mackey k...@comcast.net __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] Just a thought...
Norm, there’s lots of us out here with a K1 and KX1 that still use them!! N7EDK Sent from my iPad > On Nov 13, 2018, at 10:14 PM, Norm Lee wrote: > > Reading through all the posts on this list, it just occurred to me - am I the > last person on earth to be running a K1? > Norm vk5gi > McLaren Vale > South Australia > > Sent from my iPad __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] FT8 + AX1 in the field?
I've been meaning to try pairing the KX2 and AX1 with a notebook computer to try FT8 from the field. But hiking is all but out of the question right now in northern California due to the fires. Anyone try FT8 on their AX1 whip yet? 73, Wayne N6KR __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] FT8 + AX1 in the field?
On 11/14/18 20:28 PM, Wayne Burdick wrote: > Anyone try FT8 on their AX1 whip yet? No FT8 yet, but I did try WSPR as one of the first uses of my AX-1. On 10/25/18 10:36 AM, Steve Sergeant wrote: > I received my AX-1 yesterday. > > This morning, I took a 30 min. break at a local park with my KX2, > laptop, and the AX-1 with provided counterpoise. > > Seated at a steel picnic table in a nearby city park, with the AX-1 > connected to the radio through a BNC elbow, I caught and made, among > others, the following WSPR spots: > > HEARD: > WB3DZC: FM07ux at 3800km > KE7A: EM12kx at 2295km > > HEARD-BY: > AI6VN/KH6: BL10rx at 3798km > VE3OWV: FN15vk at 3857km > ND1C: EL99jl at 3844km __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com