[Elecraft] KXPD2 Keyer
I just received my KXPD2 Keyer. First impressions are that it is very nice. I say that only because the KXPD1 that I got for my KX1 was a booger to adjust. My question is about the extra parts that arrived with the KXPD2, came with a loose spring and two Allen screws. Additionally the photos I have seen of the KXPD2 appear to show locking set screws that I assume lock in the adjustment screws, and on mine those holes are tapped for screws but no screws are there. The instructions mention that there is a compound on the adjustment screws the prevent the adjustment screws from walking out. Are the loose screws and spring spares? Or are they something that I can install? 73 K2CG Chuck G __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] Elecraft KX1 remains keyed with straight
My KX1 remains keyed when I use a straight key, but works fine when I change settings and use a paddle. Any recommendations? __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] KX1 Straight Key issue
My KX1 works fine with a paddle. When set to "hand" for a straight key, when I press the key the KX1 stays keyed until I unplug the key __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
RE: [Elecraft] (no subject)
Steve, The KX1 uses the existing LED. Tom has some great directions, follow the link. http://www.n0ss.net/k6xx_cw_tun_ind_smd_v2_assy-align_kx1_ver.pdf 73 K2CG Chuck Gehring -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of STEPHEN W BANKS Sent: Saturday, April 26, 2008 10:31 AM To: Elecraft Subject: [Elecraft] (no subject) Hello Everyone, Recently I purchased two of the LED CW Indicator kits through the Eastern PA QRP Club. I THINK - - but now I'm not sure - - that the kit is designed to install in either/both my K2 and in my KX1 rigs. In looking over the kit and my KX1, I can't see which button the LED installs in, or if it's intended to be situated elsewhere. Is the idea is to pick one of the three buttons and drill it? The K2 is no problem as I received a drilled new button for it, but the KX1 has me guessing. Tom Hammond's website has a couple of photos of the completed indicator in place just prior to buttoning up the KX1, but nowhere is the finished installation shown that I can see. Maybe I misunderstood the intent of the kit. If it is designed to be used in the KX1, can anyone steer me to where the indicator LED installs? Does it peek out of a newly drilled chassis hole someplace? If so, where? Any help would sure be appreciated. Thanks es 73... Steve Banks K0PQ ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] KX-1 cover
Bob, The Pelican Micro 1060 is a nice fit for the KX1 73 Chuck G. K2CG ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
RE: [Elecraft] Key Paddle Kits
American Morse has several nice key kits, nicely engineering very sturdy solid keys. http://www.americanmorse.com/index.htm 73 Chuck -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Doug Person Sent: Thursday, January 24, 2008 9:56 PM To: Elecraft Discussion List Subject: [Elecraft] Key Paddle Kits Thanks for everyone's comments. The Black Widow seems like a great deal so I ordered one. I have collection of keys none of which I'm very happy with. Most are on ebay right now and not getting much attention. I hope to end up with a nice, light compact key with good action and heavy one that stays put. If the Black Widow doesn't give me the feel I want then I'm going to try a Kent or an Elecraft HexKey. I hate to invest that much since I don't work that much cw anymore. I'm finding it hard to make good contacts at my leisurely 15 wpm. And what is up with these ops sending code with about a millisecond between their dots and dashes? Is that a kind of I'll work you if you can copy me attitude? I don't get these highly stylized sending patterns. Is it meant to intentionally make it hard to copy? 73, Doug -- K0DXV ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] Polar Bear QRP Event
The Polar Bear Moonlight Madness Event will be taking place tomorrow 19 January, 2008. QRP operating frequencies 20, 30, 40 and 80 meters between 1700-2300 UTC. Our fingers may be a little cold so “BEAR” with us if our replies are a little slow. Several Polar Bear QRP Operators will be taking to the field under the frosty full moon to capture a few QSO’s. We polar bears just love operating in the great outdoors. All PBMMEs are held close to full moons during the months of October, November, December, January, February and March. That's right - when it's cold! As a small incentive for folks to make QSO’s with the Polar Bears, A limited edition Polar Bear Backpacking Alcohol Stove, wind screen and fuel bottle will be given away to the operator who makes the most QSO’s with the Polar Bears. A look at the stove and a list of a few of the operators is on the web page. http://www.polarbearqrp.org/PBMME01-08.html To apply for the prize you must send in a copy of your log. (NOTE: Logs should reflect: Time of QSO in UTC, Freq, and Polar Bear Number) Send a copy of your log via email in ASCII format to K2CG (at sign) arrl.net All logs must be received by 25 January 2008. This is not meant to be a contest so please avoid the hit and run QSO’s. If you tag us on 30 meters then the hope is that you will chat for a little before moving on. Polar Bears should be identifying themselves by calling “CQ CQ PBMM DE...” Thanks and 72 K2CG Chuck G. Polar Bear #16 ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
RE: [Elecraft] KPA100 first test question
Werner, I believe that the modification that Bill is referring to is found on the following web pages http://www.kk7p.com/k2kpa100.html#KAT100 And not in the Elecraft manuals 73 K2CG Chuck G. -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Dr. Werner Furlan Sent: Monday, November 12, 2007 4:55 PM To: Bill Coleman N2BC Cc: elecraft@mailman.qth.net Subject: Re: [Elecraft] KPA100 first test question Bill, and all who replied, I followed your unisono recommendation and did the tests with the K2. Everything worked like it should. :-)) Bill Coleman N2BC schrieb am 12 Nov 2007 um 13:23: There is a minor modification needed to the KIO2 AUX bus connector anyway (increasing the size of the RFC on the AUX connector board to handle the additional current). hm... did not realize this until now. Do you know by chance where this topic is covered in the manual? Asking questions on this list gave me not only answers but other valuble input I had not thought of otherwise. tnx a lot. 73! de Werner OE9FWV -- If you were going to shoot a mime, would you use a silencer? Email powered by Pegasus Mail free at http://www.pmail.com Homepage: http://www.qsl.net/oe9fwv/ Fone +43 5522 75013 Fax +43 820 555 85 2621 Mobile +43 664 6340014 Elecraft K2 #5203 ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
RE: [Elecraft] lousy audio ?
I built my external speaker using Tom Hammond's excellent instructions and amp. http://k2qrp.com/Radio%20Projects.htm I have since improved the basic speaker amp combination with the New England QRP NESCAF audio filter http://newenglandqrp.org/nescaf I am very pleased with the results 73, Chuck K2CG -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of F5vjc Sent: Saturday, August 25, 2007 3:05 AM To: Elecraft Subject: [Elecraft] lousy audio ? So, how about someone comming up with a good communications quality amplified speaker and enclosure design, RFI proof of course! I would build one...I believe there was/is an Elecraft design but it looked overly complex... Anyone care to suggest a suitable audio chip, speaker and enclosure? -- 73, Deni F5VJC ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] K3 Options and accesories
Does Elecraft have any plans to make available some EC3, EC2, or EC1 Enclosures available in the K3 paint color? As nice as the K3 may be I can't imagine that very many of us Elecrafter's will remain idle with a stock radio for very long before we decide that we need some type of custom external accessory and it of course will have to be built in a matching Elecraft enclosure. 73, K2CG Chuck G. ...and still K2CG because K3CG is already taken ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] N Connectors on KPA100 and KAT100
I am considering changing out all of my antenna connectors over from PL-259/ S0-239, and converting them to N Connectors/ UG-58B/U. Are there any issues that I should be concerned with on my KAT100 and KPA100? 73 K2CG Chuck Gehring ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] K1 160 meter modification
I am looking for instructions to build or modify a KFL1-2 filter board for 160 meter operations. 73 K2CG Chuck G. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] K2 KIO2 Problem.
K2 KIO2 Problem. A few days ago we had a power fluctuation in our neighborhood. The surge protector and Battery Backup UPS did not help. The Power surge took out my computer hard drive, serial interface card and it would appear had some affect on my KIO2. The KIO2 still works with my KAT-100 and KPA 100 Change Bands and Tune, but I cannot make any connection with the computer serial interface card. I have run the Serial interface Test several times. Of course I replaced the serial card and hard drive, I even switched computers, NO JOY. I have checked all of the voltages on the KIO2 interface. The voltages on the J2, Q1, U2 all match the manual. The diodes (D1, D2 and D3) seem okay but I don't get an exact match with the manual. The voltages on the U1 and J1 don't match the trouble shooting instructions; U1-113.6 VDC U1-20 VDC U1-30 VDC U1-40 VDC U1-50VDC U1-60VDC U1-70VDC U1-89VDC U1-90VDC U1-10 0VDC U1-11 4.9 VDC U1-12 5 VDC U1-13 4.9 VDC U1-14 0VDC U1-15 5 VDC U1-16 5VDC J1-1 0VDC J1-2 -6 VDC J1-3 0VDC J1-4 OVDC J1-5 0VDC J1-6 5.5 VDC J1-7 0VDC J1-8 14VDC J1-9 8VDC Comments, suggestions would be appreciated 73 K2CG Chuck Gehring P.S. I really feel so lucky to have an Elecraft K2. A friend of mine has a IC-756PROIII, He got hit with a voltage spike last month and after several hundred dollars for replacement boards he still has to send his entire rig back the service center. I am very close to talking him in to buying a K2. At least that way he will have a Back-up rig for his K2 when the Icom gets back. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] Wireless Router Recommendations
I am getting ready to add a wireless router to my QTH computer set-up, the XYL wants to be able to move room to room with her Notebook computer. I would like to solicit recommendations for routers. I have heard some reports about QRM from various routers. I only have one radio, my K2 and it will be about 2 feet from the computer and the router antenna about 2-3 feet. I am currently considering the Linksys Wireless-N WRT300N. Recommendations and replies off-line would be appreciated. 73 K2CG Chuck Gehring ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
RE: [Elecraft] K2 Audio Output
Steve Kercel AA4AK wrote: Does the K2 produce sufficient audio power to drive a set of Bose Quiet Comfort 2 noise cancelling headphones? Has anyone on the list tried Bose Quiet Comfort 2 noise cancelling headphones with a K2? Steve, I use the Bose QuietComfort 2 noise cancelling headphones all the time with my K2. They work great. 73 K2CG Chuck Gehring ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] HFProp is not FREE!
HFProp by Julian Moss is not FREE, It is shareware, sure you can down load it and use it as an Unregistered, but I ma shure that Julian would appreciate the donation. HFProp is a very fine tool, so support shareware 73 KI4DGH Chuck Gehring -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of Sam Morgan Sent: Saturday, June 17, 2006 10:45 AM To: elecraft - qth.net Subject: [Elecraft] hfprop was Solar condx plugin for Firefox? Another (free) hf propagation software I like to use is hfprop by G4ILO go to: http://www.g4ilo.com/ select 'software' then 'hfprop' quote There are many propagation programs already in existence. However, most of them are written with the main aim of forecasting propagation over a specific path. I wanted a program that would give the big picture of what propagation should be like worldwide, and I wanted one that ran fast enough that you could quickly change band or time, and see how propagation changed. /quote Julian Moss G4ILO Not OT, he runs Elecraft twins http://www.g4ilo.com/aboutme.html :-) -- GB 73's KA5OAI Sam Morgan ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] High end paddles
Has anyone on the reflector tried one of David Saylors Paddles? He offers a 30 day money back guarantee and he may be close enough to you QTH so that you can try them out. The pictures and descriptions on his web site look great. His price is a little out of my range for the moment, but maybe by the time I am copying and sending 35-40 wpm I will be ready to let my Elecraft Hex Key retire. http://saylorsmachine.com/wk4ds.html [EMAIL PROTECTED] 73 KI4DGH Chuck Gehring ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
RE: [Elecraft] KPA100 oscillation during IARU Reg 1 Field Day
Darwin wrote: And a related question. At what power level does the fan come on? -Original Message- It always bothers me when the fan comes on even though I realize that it is normal and desirable behavior. IMHO It is my understanding the the Power transistors in the KPA-100 (2SC2879) are rated for 100W SSB PEP for each, and with that HUGE heat sink I would expect the KPA-100 to loaf along fine at 100 watts CW, 30 wpm for two minutes. I have seen a few posts where folks have added additional fans. The fan is temperature controlled it will turn on high when the heat sink temp goes above 40 degrees C and turn off two minutes after the temp goes below 37 degrees C. For me, I like it when the fan turns on, it is letting me know that my KPA-100 is functioning as it was designed. 73 KI4DGH Chuck G. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
RE: [Elecraft] Re: T1 tuner from elephant-craft
It's perfect!!! The Peanut sized Tuner with an Elephant sized performance and memory to stomp on the competition. 73 KI4DGH Chuck Gehring -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of wayne burdick Sent: Friday, May 26, 2006 3:49 PM To: Alexandra Carter Cc: Elecraft Reflector Subject: [Elecraft] Re: T1 tuner from elephant-craft Alex, I'd just as soon *not* imagine the Elephants. The E is for elegant :) I'll busy forgetting this for the rest of the day Wayne On May 26, 2006, at 1:30 PM, Alexandra Carter wrote: Yerg, but Eham's still down. I'll write an even better one when the site's back up, it'll be the bestest review in the whole wide world! Or something. I have to admit, when I first heard the name Elecraft, I imagined a cartoon of a bunch of elephants sitting around a table building stuff. ought to draw it someday. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] FS Palm K2 Controller and logging package
For Sale: Palm Vx. Logging and Radio Controller package with charging/sync cradle, Wall Wart power supply, Hard carrying case, Palm folding keyboard, Travel charging/sync cable, Gender Changer, NK0E Serial CW Sender Interface, and Triple-pen-pencil-stylus pen. Pre-loaded with NK0E GoLog (version 1.2.5 loaded and tested) K2 Logger, (works with Elecraft K2 to control rig and logging) Mini-Log, QSO-73, Band Plan, HF Log, and ARS Spartan Sprint, Complete Palm software on disk and documentation. $65 shipped within CONUS Pictures on request of complete package Contact Offline [EMAIL PROTECTED] 73 KI4DGH Chuck Gehring ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] Free KXB30 Module
I would also like to offer a free KXB30 Module. The Module worked perfect when it was removed from my KX1 to install the KXB3080. I will be coming to Dayton this weekend so I can hand deliver or you can send me the cost of postage. Reply to me offline and I will even provide digital pictures. 73 KI4DGH Chuck Gehring ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
RE: [Elecraft] KX1 Tricks
Drew, Setting up a vertical in Tent City can be a real pain because the radials and keeping the troops from tripping over everything. My recommendation would be to setup a large fiberglass pole like the 31' Jackite between the tents (between the tents were they have the A/C units setup) and use a doublet antenna like KQ6XA Bonnie Crystal's Mini-Bac as an Inverted Vee to the tops of the tents, or get two Jackite poles and set it up as a Doublet. I would use Gorilla tape around the sections of the fiberglass poles for a more permanent installation. Finally get an Plano Jumbo Airliner Case to carry and ship the wires and fiberglass poles. With the Plano case you don't have to worry about them putting your stuff on a pallet when you return CONUS, or when you check it as luggage on the airlines. http://tinyurl.com/7587g Bonnie Crystal KQ6XA Mini Bac http://tinyurl.com/phh9m Jackite poles http://tinyurl.com/nx3yv Gorilla Tape http://tinyurl.com/mm4wa Plano Jumbo Airliner Case 73, KI4DGH Chuck Gehring -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of [EMAIL PROTECTED] Sent: Monday, May 08, 2006 5:14 PM To: elecraft@mailman.qth.net Subject: [Elecraft] KX1 Tricks Greetings, I'm one of the lurkers who follow this list, but haven't had anything to contribute. I am currently 1/2 way through my one year deployment to Kuwait and put together a KX1 here in my billeting to try to make a DXpedition out of the rest of my time here. I have a big plastic tote to use as my footlocker and spread a towel on it to make a work surface. The kit went together fine: my challenges have been elsewhere. I've got plenty of wire with which to make an antenna, but the tents are only 12' at the peak, there are no trees. Vertical support is an obstacle. I found a PAC 12 vertical second-hand on one of the trader pages. For a guy that enjoys stringing wire, a store-bought antenna is a bitter pill to swallow. I do like the design, though. I'm eager to transmit through it. Reciprocal licensing is a challenge, too. The ministry only accepts the form filled in Arabic, and it has to be hand-carried. I am submitting the application tomorrow, so hopefully that will go smoothly. I am taking 2 weeks of leave soon. My wife and I will meet in Scotland. I am looking forward to operating there where I don't have the licensing hoops to jump through. For people looking for a wallet in which to carry your KX1: a military accessory company called Spec.-Ops. makes a Mini Cargo Pocket Organizer that fits the KX1 like a glove. It is a heavy-duty nylon that is very durable. You do have to take the paddle off the radio, though. The organizer is found at: http://www.specopsbrand.com/main.html 73s CPT Drew Neve Battle Captain S3 ASG-Kuwait Eager to Assist ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
RE: [Elecraft] CW signal raspy, underwater, motorboating
http://tinyurl.com/kr5nf Try this URL 73 KI4DGH Chuck G ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] KAF2 or KDSP2 for K2
FWIW, I operate CW only and have the KAF2 and the KDSP2 installed in my K2. For the most part I find that I only need the XFIL set to FL2 at 500Hz. However there are times when the bands are crowded or noisy and I am trying to work a weak signal. Then I find that the KDSP2 with the Denoiser and CW Filter Gain adjusted for 12db gain to be very helpful in picking up the weak stations. I really like being able to tweak and adjust the KDSP2 filters with its very large selection of settings and adjustments. 73, KI4DGH Chuck Gehring ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] S meter Settings on the KX1
Are the range for the High and Low S-meter on the KX1 with Firmware Rev. 1.02, now Low 40-99, and High 2-7 ? The manual says Low 30-99, High 2-6. I was just triple checking all of my previous settings on my KX1 since I installed the new firmware and my S-meter settings are now slightly different. Previously L-68, H-4, now they are L-70, H-3. Of course I used my XG-2 for my S9 signal source. 73, KI4DGH Chuck Gehring ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] WA3WSJ: Check out the Jackite 31' Pole to support your Antennas
Edward R. Breneiser [EMAIL PROTECTED] wrote: Hello all! Just did an evaluation on the Jackite 31' Kite Pole. Ed that is great news. That is exactly the same Fiberglass Pole that I bought for my hopefully newly constructed DK9SQ Antenna. Ebay lists them for $45.00. At the time they listed Black 31' Jackite poles. It was delivered to my door in four days direct from Jackiite. http://tinyurl.com/l8okb 73 KI4DGH Chuck Gehring ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] T1 ATU Battery storage tip
This last weekend I finished construction on my T1 auto-tuner. The manual recommends that for transport that you reverse the battery in the storage compartment. I tried that and was not real comfortable with hearing the battery flop around as I walked around with the T1 in my fanny pack. I have inserted a small strip 1 of magnetic tape with an adhesive backing into the battery compartment. So far it does not seem to have any adverse effect on the T1's performance. The magnetic tape is the type you can find in small rolls at any hobby or craft shop. For what it is worth I figured I would pass on the tip. 73, KI4DGH Chuck Gehring ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] KXB3080 HELP KX1 will not turn on
I have just finished Part I Modify the KX1 PCB section and now I am attempting the steps for Alignment and Test -Part II for receiver alignment to confirm that the modifications have been correctly installed. Obviously I messed something up. Nothing happens during power up. I get power up to the power switch but when I turn on the switch nothing happens, no LED no relays clicking nothing. I had a KXB30 installed and completely removed the KXB30 board and all wires. I would really appreciate some help troubleshooting this problem. 73 KI4DGH Chuck Gehring ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
RE: [Elecraft] KXB3080 HELP KX1 will not turn on
Ron, Thanks, That is exactly what I did. I put the screw in there to hold the nylon shoulder in place while I worked on everything. I removed the screw and power came on. Its nice to know that I am in good company. BTW I noticed that if I had gone to the KX1 Manual for trouble shooting that the manual would have told me what I did and could have spared myself the public humiliation. Thanks again 73 KI4DGH Chuck Gehring -Original Message- From: Ron D'Eau Claire [mailto:[EMAIL PROTECTED] Sent: Saturday, March 25, 2006 7:05 PM To: 'Chuck Gehring'; elecraft@mailman.qth.net Subject: RE: [Elecraft] KXB3080 HELP KX1 will not turn on Chuck, KI4DGH asked: I have just finished Part I Modify the KX1 PCB section and now I am attempting the steps for Alignment and Test -Part II for receiver alignment to confirm that the modifications have been correctly installed. Obviously I messed something up. Nothing happens during power up. I get power up to the power switch but when I turn on the switch nothing happens, no LED no relays clicking nothing. I had a KXB30 installed and completely removed the KXB30 board and all wires. I would really appreciate some help troubleshooting this problem. - Do you have a metal screw holding the final amplifier mounting hardware together, Chuck? If you put a metal screw in the final amp without the heat sink, you're shorting the B+ to ground! Right off hand that's all I can think of at this point. All you've done is remove the KXB30 module and reconfigure the receiver input circuit. That doesn't involve any direct connections to the B+ circuitry. If it's not the 'screw in the final amplifier' bit (which probably half of the KX1 owners have done with the unit open, including me!) I'd look very closely for a solder bridge somewhere around the components you just replaced or the transformer you added. Ron AC7AC ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] Elecraft KX1 KXB3080 module
Is there any word on when the KX1 30 and 80 meter module will be available? 73 KI4DGH Chuck ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] FS FT-100 Tuning Knob and Code Quick CW training program
FT-100 tuning knob $12 Code Quick CW Training program $10 I have an Yaesu FT-100 tuning knob that I used on my K2. It looked good and worked great, however I longed for the stock Elecraft look so I installed the Finger Dimple on my K2 knob and I am very pleased with the results. So if someone has been looking for a very nice tuning knob for their K2 the FT-100 knob is available for $12 including shipping in the US. I also have a complete set of Code Quick tapes (including the manual and cards). Code Quick may not be the preferred training method to some, but it made learning code fun and got me up and on the air so I would like to see them in continued service. Code Quick tapes $10 in the US. 73, KI4DGH Chuck Gehring ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] FS FT-100 Tuning Knob and Code Quick has been sold
The response was very quick. The FT-100 Tuning knob and Code Quick Programs have already been spoken for. 73 KI4DGH Chuck Gehring ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] OT Kent Two Staright Key and Paddle combo
For the benefit of those on the Elecraft reflector that ordered a Kent Two Combo. It appears there was more than just a couple of us. Well my Kent Two, key and paddle combo that I ordered on 9 December arrived in the mail today. Looks great but Santa snatched it up and put it back under the tree, Bah humbug! http://tinyurl.com/awrdb 72 KI4DGH Chuck Gehring ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
RE: [Elecraft] Connecting Kent Straight Key and Paddle
Jeff, I have mine already configured and ready to go. I used a Radio Shack Stereo Y cable RS 42-2463. Connected the paddle to one side of the Y cable with a RS 274-284. From the straight key I used a RS 274-274 in line stereo jack that I modified in accordance with the K2 manual page 95 figure 8-1 and a short pice of 1/8 stereo cable (about 6) RS42-2387. I plugged the straight key into the modified stereo jack and the 6 extension with the stereo plug into the other Y cable connection. With this set up I can use either may paddle or straight key all the time any time? I hope this helps Chuck Gehring -Original Message- Subject: [Elecraft] Connecting Kent Straight Key and Paddle For instance what kind of plug (for each wire) and how soldered to the plug. Just to take my best guess I've already bought RS Part 274-284 1/8 stereo phone plug, and wonder if these will work. If so how to solder? Sorry to be such a dope- TIa, Jeff KG6ZVT ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] K2 Anomaly
K2 Anomaly I have experienced an anomaly; at least I think it is an anomaly on my K2. When I am rotating the VFO knob the frequency display will disappear very briefly and be replaced by my power output setting, then change back just a quickly to the frequency display. I have not been able to duplicate it with any degree of regularity; it just happens and goes back to normal. The rate of change on the VFO knob does not seem to determine when this occurs. It does not seem to have any effect on performance. Has anyone else experienced this, can anyone offer an explanation? 73, KI4DGH Chuck Gehring ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
RE: [Elecraft] Accurate QRP Wattmeters?
The Elecraft Mini-Module DL1 Dummy Load has test points that allow you to use a DMM to measure out put. I can't imagine anything in that price range being more accurate 73, KI4DGH Chuck Gehring -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of J. Coote Sent: Sunday, July 03, 2005 12:46 PM To: elecraft@mailman.qth.net Subject: [Elecraft] Accurate QRP Wattmeters? Hello List, I've posted my question on QRP-L and here as well- since I will be building a KX-1. I am looking for good ways to measure power output from my KX-1 while I am building it. What first came to mind was to set up my Tek 492 analyzer on a 2 dB scale and then use a 30 or 40 watt (high power) attenuator to measure CW power. I have several Bird 43's but have never seen Bird slugs for QRP LF, MF or HF. I think a competing company may have a through wattmeter with HF but I forget the lowest scale of that one. I have read the E-Ham reviews for the Oak Hills QRP wattmeter- 300 Khz to 54 MHz and 100mW, 1W and 10W scales- still thinking over the reviews. Comments on the accuracy of using the Tek 492 method, and on other accurate wattmeter options? 73 Jay W6CJ AAR9QM ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] KAT 100 Resistance Checks
I am building the KAT 100, the Resistance checks look fine except for U2 Pin 12 shows some resistance and then a short to ground. I have gone back and checked for solder bridges. I have checked the reflector for previous posts. I don't have U1 installed and the schematic shows pin 12 connecting to Pin 12 of U3, U4 and RYLoad. Any recommendations Chuck Gehring ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] DUH on the KAT 100 Resistance Checks
Please accept my apologies for wasting the bandwidth. I was suffering from a case of Cranial Rectal Inversion I was not counting the pins on U2 correctly. Resistance checks okay. KAT 100 passed initial tests. Chuck Gehring I am building the KAT 100, the Resistance checks look fine except for U2 Pin 12 shows some resistance and then a short to ground. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] K9YA Telegraph
The Robert F. Heytow Memorial Radio Club publishes a fantastic monthly newsletter. This month is a series of articles on QRP. If you haven't seen or heard about the publication, it is FREE and Online. http://www.k9ya.org http://mailman.qth.net/mailman/listinfo/k9ya_telegraph Spread the word... Tell your friends about the K9YA Telegraph! 73 KI4DGH Chuck Gehring ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
RE: [Elecraft] RS-232 interface question
Please DONT Reply offline. I don't think I am the only one that would like to hear some more discussion on this subject Thanks 73 KI4DGH Chuck Gehring -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of [EMAIL PROTECTED] Sent: Tuesday, March 29, 2005 6:28 AM To: elecraft@mailman.qth.net Subject: [Elecraft] RS-232 interface question Hi folks. I'm planning on building the 100W kit for my K2, and the 100W ATU, both together in a remote enclosure. Do I, or do I not, need the KIO2 RS-232 Interface kit, given that both the amp and the ATU are remote? Offline replies OK, as this is probably an old question!! Ted WB3AVD ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] External Battery for KX1
I have a pair of Radio Shack NiCad RC model car batteries 7.2 vdc 2000 mAh. I have but them in series and get 16vdc when fully charged. In the past I have put a 12 volt fan on the batteries until the charged was reduced to 13.5 vdc and then used them as an external power supply for my KX1. However there has to be a better way. Can anyone offer a simple circuit that I might put together that would provide a regulated 14vdc? 73 KI4DGH Chuck G. KX1 # 641 K2 # 4467 ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] Extended Side Panels on the K2
I have seen a previous posting about the extended side panels for the K2. Are they still available? Does nayone have an e-mail address for Randy Hagenrader K3QO formerly K4QO formerly WJ4P 73 KI4DGH Chuck G. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] KPA 100 Resistance Checks
I am building the KPA 100. I have just tried the resistance measurements on page 41 of the Alignment and Installation. The resistance measurements for the Q1 and Q2 collectors will flash 11 or 12K ohms then jump down to -6.5K ohms and then count up to -3.5K and then stabilize. When I first checked the J3 red terminal it responded normally in about 20 seconds showing greater than 10 K ohms. Now even that is giving me inconsistent readings. The remainder of the readings in that table for the KPA 100 test points are okay. I saw a similar post in the archives from Dec 2004 but the thread ended without a response. Comments Recommendations would be appreciated 73, KI4DGH Chuck Gehring ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] K2 4467 on the Air
Well we made it, K2 #4467 is finally on the air. Our first CQ was answered by K4THL with his K1, now that was sweet. The rig is working fine on all bands, I haven't completed a full shake down but so far so good. I still have some questions, but nothing that I can't live with for now. I never did get a perfect match between the BFO and the VFO following N6KR Wayne's instructions for calibrating the 4 MHz Master Oscillator. The best I could manage was 220 Hz difference measuring between TP1 and TP2. But I only ran the procedure once and may try it again later. I hope I didn't overheat the crystal applying the ground to the case. During the Final Alignment I used the Elecraft N-Gen as a signal source. It was difficult to find a peak during the Receiver Pre-Alignment on 3750 adjusting L3 and L4. There was a peak but very flat and wide. Finding the Peak on 17 meters during the Pre-Alignment, never happened using C32 and C34. I finally left them at the mid range and got a peak during the Transmitter Alignment. I also have the QSK Thump on the speaker and headset that I have read about on the Archives. It is a little different from my Ten Tec rig but I'll manage. I really want to extend my whole hearted Thanks to the entire crew at Elecraft, super rig and great instructions. All of my parts were there, Thanks Christine and Kim, Super Job. My Thanks to Gary for dealing with all the questions. Finally thanks to you guys on the Elecraft Reflector for the recommendations and reassurance that I was not the only one who did something stupid, by installing a diode in backwards. Your secret is safe with me guys. 73, KI4DGH Chuck Gehring ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] 40 Meter Transmitter Alignment, Inconsistent Readings
I am trying the 40 Meter Transmitter Alignment procedure. Adjusting the L1 and L2 for a maximum of 2.0 watts did not seem to be a problem. With the VFO set to 7100 and power setting set for 2.0 watts. The initial indication was about 3.0 watts at 1.5 amps. I adjusted the L1 and L2 until I get a reading of 1.9 watts with the power set for 2.0 watts with 1.26 amps indicated. I changed the power setting to 5.0 watts and it indicates 6.9 watts with 1.8 amps. I increased to 10 watts to get a reading of 12 watts with 2.0 amps. Then I decreased the power setting back to 2.0 watts without changing anything except the power setting and press and hold the TUNE button it reads 2.5 watts. Increasing and decreasing the power setting up then down between 2 to 5 Watts I get 1.9 to 2.6 watts with the setting set for 2.0 watts. The power meter on my dummy load pretty much reflects the same power out as indicated on the internal power meter. Am I making a mountain out of a mole hill here or is something wrong. 73 KI4DGH Chuck Gehring ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] KDSP2 Capacitor Installation
I need some recommendations. The KDSP2 instructions state to install C5, C8,C3, and C4 with the capacitor flush to tje PCB with the exposed leads not more than 1/32 (1mm) above the PCB. Could someone please tell me how they accomplished this task. The best I can mamage without cracking the ceramic around the leads is 2/32 Pictures would be great. 73, KI4DGH Chuck Gehring ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] Keying on Power Up
I just finished up Assembly Part II, getting ready to start Alignment and Test Part III. When I turn on my K2 the display shows Elecraft and then flashes between PO 1 and SPD 15. NO INFO messages, the dummy load gets warm. No Smoke so I guess I can count my blessings. I will be searching the reflector archives and double checking for shorts again, but I am afraid that I am overlooking the same spot each time. 73 KI4DGH Chuck Gehring ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
RE: [Elecraft] Noise-reducing cans
It's not pasword protected the link had a typo, it should be a forward slash after roadwarriorcontent try http://www.thetravelinsider.info/roadwarriorcontent/planequietnc6headphones. htm 73 KI4DGH Chuck Gehring -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of William Johnson Sent: Monday, January 03, 2005 8:08 AM To: 'David J Windisch'; Elecraft@mailman.qth.net Subject: RE: [Elecraft] Noise-reducing cans The link is password protected. Bill -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of David J Windisch Sent: Monday, January 03, 2005 7:34 AM To: Elecraft@mailman.qth.net Subject: [Elecraft] Noise-reducing cans Hi, all concerned: I have tinnitus and some hearing loss at age 61, and have found the PlaneQuiet NC-5 cans helpful in the shack and in the mfg shop where I'm a tech. They're light, and they reduce the racket from HVAC, refrigerators, freezers, amp blowers, computer blowers, and so on. http:www.thetravelinsider.info/roadwarriorcontent'planequietnc6headphones.ht m Some plans fell through, and I have 4 NC-5 sets which were new last month, in original boxes, with instructions, warranty cards, carrying pouch, and AA cell. These are the ones over which Bose apparently threatened legal action over patent infringements of some sort. The supplier gets $75 a set singly; if you're interested at $60 a set shipped domestically, pls email me, [EMAIL PROTECTED] off-reflector. TIA, HNY and 73, Dave, N3HE ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] Testing BL1 mini module
I finished assembling a BL1 BALUN Module and decided to test it with my 259 Antenna Analyzer. The testing procedure calls for you to connect a pair of 100 ohm resistors in series between the two 200 ohm terminals, then test the SWR with a jumper connected to the input shield and to three different locations on the resistors. The instructions state that the SWR should be low when the jumper is connected between the input shield and the junction between the two resistors. Then it should show poor SWR when the jumper is connected between the input shield and either one of the BALUN output terminals. My tests showed no difference between any of the three connections. I have double and triple checked my soldering connections on the BL1. It is not a complicated module to assemble. Has anyone else tested the BL1 with a 259? Is the BALUN safe to use or should I just stay away from testing equipment without adult supervision? 73, KI4DGH Chuck Gehring ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] KXer for the KX1
I just received the perfect accessory for my KX1 a new iambic paddle designed and built by Richard Meiss WB8LPU. Now I love my KX1 and the KXPD1 is a nice paddle, but I need to have that tactile feel of a regular paddle. The KXer uses the existing mounting connections connecting directly to the KX-1, or you can use it in the stand-alone mode with a brass tripod base. The paddle itself is the iambic type, with the tension provided by opposed magnets mounted on the inside of the paddle arms. It has the feel of a bigger paddle crisp action, definite stops at the end of the travel, and no drag while the paddle is moving. If you have a KX1 then you really need to check this paddle out. I believe I have the first production model of the KXer, and I could not be happier. The Form, Fit, Function, and Finish are Fantastic. I have no connection to Richard Meiss, other than the fact that I am one very happy and excited customer. Check out the August 2004 Bacon Bits newsletter for more information and pictures. http://www.fpqrp.com/BB0804.pdf or contact Richard at [EMAIL PROTECTED] 73, KI4DGH Chuck Gehring ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] Modify an Astatic D104 Desk Microphone
I have an old Astatic D104 Desk Microphone that I would like to modify to use with a modern Transceiver. Does anyone have some suggestions? 73, KI4DGH Chuck G. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraftHelp: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
RE: [Elecraft] KX1 Receiver Drain
God I hope not. I know the manual says 35ma in Receive, 40ma max w/ headphones. I was hoping that was just an average, because I have 42.1 with the Freq Readout illuminated and 39 ma when the Freq lights are not illuminated, regardless of wether the headphones are plugged in or not. 73, KI4DGH KX1 #641 Chuck Gehring -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of John von Gonten Sent: Thursday, June 24, 2004 5:40 PM To: elecraft@mailman.qth.net Subject: [Elecraft] KX1 Receiver Drain Ok, now that I have gotten replacement toroids from the Toroid guy (fast service by the way) I am on page 47, receiver drain is 36.7 ma is this in the range of considerable high, or just in the range of average. I do have a fairly high general noise level here :/ Thanks in advance 73 John N5BSD / NNN0OYH ARRL NTS ORS NTX Digital www.n5bsd.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net http://mailman.qth.net/mailman/listinfo/elecraft You must subscribe to post. Subscriber Info (Addr. Change, Unsub etc): http://mailman.qth.net/subscribers.htm Elecraft page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net http://mailman.qth.net/mailman/listinfo/elecraft You must subscribe to post. Subscriber Info (Addr. Change, Unsub etc): http://mailman.qth.net/subscribers.htm Elecraft page: http://www.elecraft.com
RE: [Elecraft] Elecraft KX1 mini-log attaches to back cover
Another Tip you may or may not find useful. Laminate your logs with clear plastic shelving paper. You can then write on it with pencil, transfer your log, erase and use them over. 73, KI4DGH Chuck Gehring -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of wayne burdick Sent: Monday, June 14, 2004 2:01 PM To: Elecraft Reflector; HF Pack; QRP-L Subject: [Elecraft] Elecraft KX1 mini-log attaches to back cover When the KX1 is used hand-held, it's difficult to log, since you need three hands (one each for the KX1, log, and pen). To simplify this, we've created a loose-leaf mini-log that attaches to the back of the radio via the thumbscrews. When operating hand-held, you simply flip the rig over and log the QSO. Even when not operating hand-held, the log sheets can be stored in this location for ready access. They're easy to get off because of the two U-shaped channels for attachment at the thumbscrews. In our tests, the log worked well even with a solder lug attached at one thumb screw (for a trailing ground wire). You'll find a .pdf file for the mini-log, and a photo showing the log sheets in use, at: http://www.elecraft.com/KX1/KX1.htm Feel free to print out as many sheets as you'd like for your own use. We suggest heavy card stock, 65 pound or higher (about the weight of business card paper). Trim out the sheets carefully using an X-acto knife or other sharp tool. You can stack quite a few sheets under the thumb screws -- certainly enough for a typical outing. You could also cut out a piece of transparency stock or Vellum to protect the paper sheets during transport. This top sheet should be moved to the bottom of the stack during operation. We didn't include columns for mode or power output level. This info could be noted in the blank area at the right of the mini-log, since it's likely to be the same for a group of QSOs. Be sure to write small! 73, Wayne, N6KR Eric, WA6HHQ --- http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net http://mailman.qth.net/mailman/listinfo/elecraft You must subscribe to post. Subscriber Info (Addr. Change, Unsub etc): http://mailman.qth.net/subscribers.htm Elecraft page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net http://mailman.qth.net/mailman/listinfo/elecraft You must subscribe to post. Subscriber Info (Addr. Change, Unsub etc): http://mailman.qth.net/subscribers.htm Elecraft page: http://www.elecraft.com
[Elecraft] KX1# 641 Finally on the Air but need help with KXAT1 Alignment and Test Help
KXAT1 Alignment and Test Help I am not sure what I am suppose to see or do in the following steps: Select 40 meters using KX1 BAND Switch (Done, I understand) Connect a 50-ohm Dummy Load (Done, I understand) Set the ATU parameter to CAL using the menu, (I think I am there. Pressed Menu, rotated the VFO knob to ATU, then press and hold MENU, rotate VFO knob to CAL.) I can hear the relays click when I go between CAL and TUN, in the ATU menu when I rotate the VFO knob. Is that how I select or bypass the ATU? I remained in the ATU CAL position while I adjusted the R1 and R2 as per the KXAT1 Manual Errata sheet Rev A-2. (The diagram was helpful, Thanks) Then I exited the ATU menu with the ATU still left in CAL, set up my DMM connected to a KX1 standoff and the REFL test point on the KXAT1 board. I entered the TUNE mode by pressing MENU and BAND at the same time. I then adjusted C9 for a null (0.7vdc) monitoring the DMM using the 2-3 VDC scale. I repeated the process using the DMMs 200-milli vdc scale I went back to the ATU menu and changed it back to TUN to support normal operations. My question really is, should I have left the ATU in the CAL position and exited to enter the TUNE mode? I measured the power out from the KX1 using the DL1 Dummy load test points. It shows a very solid 4 watts. I also installed the KXB30 meter module. During the alignment process I got a very positive peak from the 30A cap, but I really didnt see much of a response from the 30B. Chuck Gehring KI4DGH ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net http://mailman.qth.net/mailman/listinfo/elecraft You must subscribe to post. Subscriber Info (Addr. Change, Unsub etc): http://mailman.qth.net/subscribers.htm Elecraft page: http://www.elecraft.com
