Re: [MBZ] Heat pump question

[Meade Dillon via Mercedes]

Nice score!  I've got a 3 inch 12v fan from an old UPS that I'm going to
re-purpose as a ventilation fan, solar powered, in my sailboat.  It draws
some very small current, I'm thinking it is 25 mA or so.  Planning to put a
50W panel on a controller to both charge the boat's deep cycle battery and
run the fan, with a fan cut-off at 12.5 volts or so.

If I had one of those big fans it would be mo-better, but I'd have to
fabricate a new hatch and install that fan in the hatch, with some type of
weather cover to keep the rain out.
-
Max
Charleston SC


On Wed, Feb 17, 2021 at 1:35 PM Jim Cathey via Mercedes <
mercedes@okiebenz.com> wrote:

> Speaking of fans for wood stoves, I was at the thrift shop yesterday and
> found
> two 8" 12V fans.  I bought them, and they're extremely quiet.  9 blades on
> them,
> they look like submarine propellers.  They draw about 160mA each at 12V,
> and
> blow a nice amount of air.  If these were on our wood stove I doubt we'd
> notice
> them much, if at all.  Rosewill DF2003012SEMN, China.
>
> Direct 12V fans are going to be very much more power-efficient than running
> an inverter off of a battery to drive an AC fan.  One of these Rosewill
> fans on a
> typical 110AH deep-cycle battery would run for two weeks straight without
> taking
> it below 50%.
>
> -- Jim
>
>
> ___
> http://www.okiebenz.com
>
> To search list archives http://www.okiebenz.com/archive/
>
> To Unsubscribe or change delivery options go to:
> http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com
>
>
___
http://www.okiebenz.com

To search list archives http://www.okiebenz.com/archive/

To Unsubscribe or change delivery options go to:
http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com

Re: [MBZ] Heat pump question

[Jim Cathey via Mercedes]

Speaking of fans for wood stoves, I was at the thrift shop yesterday and found
two 8" 12V fans.  I bought them, and they're extremely quiet.  9 blades on them,
they look like submarine propellers.  They draw about 160mA each at 12V, and
blow a nice amount of air.  If these were on our wood stove I doubt we'd notice
them much, if at all.  Rosewill DF2003012SEMN, China.

Direct 12V fans are going to be very much more power-efficient than running
an inverter off of a battery to drive an AC fan.  One of these Rosewill fans on 
a
typical 110AH deep-cycle battery would run for two weeks straight without taking
it below 50%.

-- Jim


___
http://www.okiebenz.com

To search list archives http://www.okiebenz.com/archive/

To Unsubscribe or change delivery options go to:
http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com

Re: [MBZ] Heat pump question

[Curt Raymond via Mercedes]

 That's good news. I know people love the Honda units but I can't bear the 
price for the amount it would get used...
-Curt

On Wednesday, February 17, 2021, 1:15:27 AM EST, Scott Ritchey via Mercedes 
 wrote:  
 
 I bought one of those 2KW inverter units from Harbor Freight a few years back: 
 

https://www.harborfreight.com/engines-generators/gasoline-generators/2000-watt-super-quiet-inverter-generator-62523.html

I got it on sale for $450.  It's fairly quiet and it has a low power mode that 
is even quieter.  It has started reliably so far.  It is portable but I would 
not like to carry it far.  You need to remove a side panel (tools required) to 
check or change oil.  Some of the other maintenance is odd, like a spark plug 
buried deep inside.  Overall, it has served me well but I don't have many hours 
on it.

-Original Message-
From: Mercedes On Behalf Of Curt Raymond via Mercedes
Sent: Tuesday, February 16, 2021 11:59 AM
To: Mercedes Discussion List 
Cc: Curt Raymond 
Subject: Re: [MBZ] Heat pump question

 I've got a 1200w 2 stroke generator that has never been used "in anger". It 
outputs 12v also which can be handy.It would be super useful for you now as it 
would easily run your blower and just sip fuel. Its supposed to run 8 hours at 
half load on 1 gallon of gas.
A Honda 2000w would be better but also would be 5x the cost and considering 
I've never really needed mine I can't justify it.I have considered the Harbor 
Freight copy to have at camp. When we were up there last July it was stiflingly 
hot. Dad wants to get a small air conditioner but the 3000w "Champion" 
generator we have now is quite loud.Google suggests that a 5000BTU aircon needs 
550w/hr so the small "super quiet" generator from Harbor Freight would do the 
job easily. We've got 500 or so sqft. of camp. It wouldn't make ice cubes 
inside but would certainly take the edge off.
-Curt



    On Tuesday, February 16, 2021, 11:49:02 AM EST, Kaleb Striplin via Mercedes 
 wrote:  
 
 Nope it’s all contained in the original brick chimney. I closed the doors on 
it and will see what happens

I really need to look into a generator or some sort. 



Sent from my iPhone

> On Feb 16, 2021, at 10:43 AM, Curt Raymond  wrote:
> 
> 
> The doors will probably make more heat, you're losing it up the chimney 
> because its getting too much air.
> 
> I've got a thermometer on the stove pipe and I'm always interested in the 
> fact that maximum heat is NOT achieved with maximum air. You've got to run a 
> lot of air to get the fire going and to get the stove/chimney warm but then 
> you need to restrict air some to get max heat. I don't completely understand 
> why but its a fact, at least in my stove. Some of the heat has to go into the 
> chimney, otherwise you won't be able to maintain good draft. Outside chimneys 
> might look cool but they suck for actually burning wood.
> 
> Do you have a pipe coming out of yours you can put a magnetic stove 
> thermometer on? Without one you'll produce less heat and burn way more wood 
> since you don't really know whats happening.
> 
> -Curt
> 
> On Tuesday, February 16, 2021, 11:36:05 AM EST, Kaleb Striplin via Mercedes 
>  wrote:
> 
> 
> Got the fire going. Of course it will take a while to start putting off some 
> heat. Without the doors closed and the blower going, it seems like it’s 
> probably operating like a regular fireplace with most of the heat going ok 
> the chimney. 
> 
> Sent from my iPhone
> 
> > On Feb 16, 2021, at 10:07 AM, Curt Raymond  wrote:
> > 
> > 
> > Some of those units do pretty amazing things in the cold these days. 10-15 
> > years ago 20F was the practical minimum but I've read of units that will 
> > still work down to 0F and there are some that probably go colder. I suspect 
> > efficiency takes a dump at those temps though.
> > 
> > The guy I'm training to run the groomer is an HVAC installer and the other 
> > night he was telling me that just about nobody is installing ground source 
> > heat pumps any more due to the huge cost and the availability of low temp 
> > air source units combined with the low cost of natural gas.
> > 
> > I'd considered ground source but the ones I've looked at are $20,000+ while 
> > a new boiler for our house is more like $6,000 and would decrease our oil 
> > use 20-25%. It would take a long long time to pay off that extra cost. 
> > There are incentives but they're decreasing every year.
> > 
> > -Curt
> > 
> > On Tuesday, February 16, 2021, 10:46:10 AM EST, Kaleb Striplin via Mercedes 
> >  wrote:
> > 
> > 
> > I don’t know if size matters but it

Re: [MBZ] Heat pump question

[Scott Ritchey via Mercedes]

I bought one of those 2KW inverter units from Harbor Freight a few years back:  

https://www.harborfreight.com/engines-generators/gasoline-generators/2000-watt-super-quiet-inverter-generator-62523.html

I got it on sale for $450.  It's fairly quiet and it has a low power mode that 
is even quieter.  It has started reliably so far.  It is portable but I would 
not like to carry it far.  You need to remove a side panel (tools required) to 
check or change oil.  Some of the other maintenance is odd, like a spark plug 
buried deep inside.  Overall, it has served me well but I don't have many hours 
on it.

-Original Message-
From: Mercedes On Behalf Of Curt Raymond via Mercedes
Sent: Tuesday, February 16, 2021 11:59 AM
To: Mercedes Discussion List 
Cc: Curt Raymond 
Subject: Re: [MBZ] Heat pump question

 I've got a 1200w 2 stroke generator that has never been used "in anger". It 
outputs 12v also which can be handy.It would be super useful for you now as it 
would easily run your blower and just sip fuel. Its supposed to run 8 hours at 
half load on 1 gallon of gas.
A Honda 2000w would be better but also would be 5x the cost and considering 
I've never really needed mine I can't justify it.I have considered the Harbor 
Freight copy to have at camp. When we were up there last July it was stiflingly 
hot. Dad wants to get a small air conditioner but the 3000w "Champion" 
generator we have now is quite loud.Google suggests that a 5000BTU aircon needs 
550w/hr so the small "super quiet" generator from Harbor Freight would do the 
job easily. We've got 500 or so sqft. of camp. It wouldn't make ice cubes 
inside but would certainly take the edge off.
-Curt



On Tuesday, February 16, 2021, 11:49:02 AM EST, Kaleb Striplin via Mercedes 
 wrote:  
 
 Nope it’s all contained in the original brick chimney. I closed the doors on 
it and will see what happens

I really need to look into a generator or some sort. 



Sent from my iPhone

> On Feb 16, 2021, at 10:43 AM, Curt Raymond  wrote:
> 
> 
> The doors will probably make more heat, you're losing it up the chimney 
> because its getting too much air.
> 
> I've got a thermometer on the stove pipe and I'm always interested in the 
> fact that maximum heat is NOT achieved with maximum air. You've got to run a 
> lot of air to get the fire going and to get the stove/chimney warm but then 
> you need to restrict air some to get max heat. I don't completely understand 
> why but its a fact, at least in my stove. Some of the heat has to go into the 
> chimney, otherwise you won't be able to maintain good draft. Outside chimneys 
> might look cool but they suck for actually burning wood.
> 
> Do you have a pipe coming out of yours you can put a magnetic stove 
> thermometer on? Without one you'll produce less heat and burn way more wood 
> since you don't really know whats happening.
> 
> -Curt
> 
> On Tuesday, February 16, 2021, 11:36:05 AM EST, Kaleb Striplin via Mercedes 
>  wrote:
> 
> 
> Got the fire going. Of course it will take a while to start putting off some 
> heat. Without the doors closed and the blower going, it seems like it’s 
> probably operating like a regular fireplace with most of the heat going ok 
> the chimney. 
> 
> Sent from my iPhone
> 
> > On Feb 16, 2021, at 10:07 AM, Curt Raymond  wrote:
> > 
> > 
> > Some of those units do pretty amazing things in the cold these days. 10-15 
> > years ago 20F was the practical minimum but I've read of units that will 
> > still work down to 0F and there are some that probably go colder. I suspect 
> > efficiency takes a dump at those temps though.
> > 
> > The guy I'm training to run the groomer is an HVAC installer and the other 
> > night he was telling me that just about nobody is installing ground source 
> > heat pumps any more due to the huge cost and the availability of low temp 
> > air source units combined with the low cost of natural gas.
> > 
> > I'd considered ground source but the ones I've looked at are $20,000+ while 
> > a new boiler for our house is more like $6,000 and would decrease our oil 
> > use 20-25%. It would take a long long time to pay off that extra cost. 
> > There are incentives but they're decreasing every year.
> > 
> > -Curt
> > 
> > On Tuesday, February 16, 2021, 10:46:10 AM EST, Kaleb Striplin via Mercedes 
> >  wrote:
> > 
> > 
> > I don’t know if size matters but it’s a 5 ton unit and even when it was in 
> > the single digest I could tell it was putting out heat. I could tell the 
> > difference between when the outside unit was running and when it was shut 
> > down and onl

Re: [MBZ] Heat pump question

[Curt Raymond via Mercedes]

 Oh, there isn't a space between the  end of my link and the next 
word.https://lanternnet.com/product/dietz-10-monarch-hot-blast-lantern/
I'll try two spaces this time. The list serv and Yahoo mail don't really get 
along. The list serv strips out most of my formatting.
Any of those lanterns will probably do the job. Sometimes when its cold here 
and I don't want to run the electric heater I'll fire up an Aladdin or my B&H 
circular wick lamp. They make nice heat.
-Curt

On Tuesday, February 16, 2021, 6:18:50 PM EST, OK Don via Mercedes 
 wrote:  
 
 Like this one? Might keep an 8X8X8 well house above freezing with -10°F
temps? Your like went to a 30W incandescent bulb:
https://lanternnet.com/product/dietz-80-blizzard-cold-blast-lantern/


On Tue, Feb 16, 2021 at 3:04 PM Curt Raymond via Mercedes <
mercedes@okiebenz.com> wrote:

>  A look at Craigslist/yard sales/flea markets will yield loads of these
> tubular lanterns.
>
> Jim's link is a cold blast version, the doodad at the top takes air from
> outside, funnels it down those tubes where it gets to the flame. Cold blast
> lanterns make the most light for fuel volume in the flat wick lantern
> family.
>
> Alternately:
> https://lanternnet.com/product/dietz-10-monarch-hot-blast-lantern/That's
> a hot blast lantern, no doodad at the top, it recaptures a portion of the
> gasses coming from the burner and sends them back to the flame to be burned
> again. A hot blast lantern makes less light but uses less fuel since
> there's a little bit of unburned fuel in the output of the burner. Hot
> blast lanterns tend to burn longer per unit of fuel but put off less light.
> They also tend to make less smell if that's a consideration in your
> situation.
>
> For max light in a silent lamp you want:
> https://lanternnet.com/product/w-t-kirkman-ramona-table-lamp-w-500-aladdin-burner/
> which is a round wick lamp, the wick is a tube. On this one the wick heats
> a mantle for more light output. Probably not all that useful for the well
> house though, and kinda spendy.
> -Curt
>
>    On Tuesday, February 16, 2021, 2:01:37 PM EST, Jim Cathey via Mercedes
>  wrote:
>
>  > I need a kerosene lamp - what/where do I get one? Recommendations
> please.
>
> What about:
> https://www.redhillgeneralstore.com/Oil-Lanterns/Camping-Oil-Lantern.htm?color=red
> <
> https://www.redhillgeneralstore.com/Oil-Lanterns/Camping-Oil-Lantern.htm?color=red
> >
>
> 45 hour burn time.
>
> -- Jim
>
> ___
> http://www.okiebenz.com
>
> To search list archives http://www.okiebenz.com/archive/
>
> To Unsubscribe or change delivery options go to:
> http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com
>
>
> ___
> http://www.okiebenz.com
>
> To search list archives http://www.okiebenz.com/archive/
>
> To Unsubscribe or change delivery options go to:
> http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com
>
>

-- 
OK Don

"Whenever you find yourself on the side of the majority, it is time to
pause and reflect." Mark Twain

“Basic research is what I’m doing when I don’t know what I am doing.”  Wernher
Von Braun
2013 F150, 18 mpg
2017 Subaru Legacy, 30 mpg
1957 C182A, 12 mpg - but at 150 mph!
___
http://www.okiebenz.com

To search list archives http://www.okiebenz.com/archive/

To Unsubscribe or change delivery options go to:
http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com

  
___
http://www.okiebenz.com

To search list archives http://www.okiebenz.com/archive/

To Unsubscribe or change delivery options go to:
http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com

Re: [MBZ] Heat pump question

[OK Don via Mercedes]

Got the hot/cold blasts confused. This one is hot -
https://lanternnet.com/product/dietz-10-monarch-hot-blast-lantern/

On Tue, Feb 16, 2021 at 5:17 PM OK Don  wrote:

> Like this one? Might keep an 8X8X8 well house above freezing with -10°F
> temps? Your like went to a 30W incandescent bulb:
> https://lanternnet.com/product/dietz-80-blizzard-cold-blast-lantern/
>
>
> On Tue, Feb 16, 2021 at 3:04 PM Curt Raymond via Mercedes <
> mercedes@okiebenz.com> wrote:
>
>>  A look at Craigslist/yard sales/flea markets will yield loads of these
>> tubular lanterns.
>>
>> Jim's link is a cold blast version, the doodad at the top takes air from
>> outside, funnels it down those tubes where it gets to the flame. Cold blast
>> lanterns make the most light for fuel volume in the flat wick lantern
>> family.
>>
>> Alternately:
>> https://lanternnet.com/product/dietz-10-monarch-hot-blast-lantern/That's
>> a hot blast lantern, no doodad at the top, it recaptures a portion of the
>> gasses coming from the burner and sends them back to the flame to be burned
>> again. A hot blast lantern makes less light but uses less fuel since
>> there's a little bit of unburned fuel in the output of the burner. Hot
>> blast lanterns tend to burn longer per unit of fuel but put off less light.
>> They also tend to make less smell if that's a consideration in your
>> situation.
>>
>> For max light in a silent lamp you want:
>> https://lanternnet.com/product/w-t-kirkman-ramona-table-lamp-w-500-aladdin-burner/
>> which is a round wick lamp, the wick is a tube. On this one the wick heats
>> a mantle for more light output. Probably not all that useful for the well
>> house though, and kinda spendy.
>> -Curt
>>
>> On Tuesday, February 16, 2021, 2:01:37 PM EST, Jim Cathey via
>> Mercedes  wrote:
>>
>>  > I need a kerosene lamp - what/where do I get one? Recommendations
>> please.
>>
>> What about:
>> https://www.redhillgeneralstore.com/Oil-Lanterns/Camping-Oil-Lantern.htm?color=red
>> <
>> https://www.redhillgeneralstore.com/Oil-Lanterns/Camping-Oil-Lantern.htm?color=red
>> >
>>
>> 45 hour burn time.
>>
>> -- Jim
>>
>> ___
>> http://www.okiebenz.com
>>
>> To search list archives http://www.okiebenz.com/archive/
>>
>> To Unsubscribe or change delivery options go to:
>> http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com
>>
>>
>> ___
>> http://www.okiebenz.com
>>
>> To search list archives http://www.okiebenz.com/archive/
>>
>> To Unsubscribe or change delivery options go to:
>> http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com
>>
>>
>
> --
> OK Don
>
> "Whenever you find yourself on the side of the majority, it is time to
> pause and reflect." Mark Twain
>
> “Basic research is what I’m doing when I don’t know what I am doing.”  Wernher
> Von Braun
> 2013 F150, 18 mpg
> 2017 Subaru Legacy, 30 mpg
> 1957 C182A, 12 mpg - but at 150 mph!
>


-- 
OK Don

"Whenever you find yourself on the side of the majority, it is time to
pause and reflect." Mark Twain

“Basic research is what I’m doing when I don’t know what I am doing.”  Wernher
Von Braun
2013 F150, 18 mpg
2017 Subaru Legacy, 30 mpg
1957 C182A, 12 mpg - but at 150 mph!
___
http://www.okiebenz.com

To search list archives http://www.okiebenz.com/archive/

To Unsubscribe or change delivery options go to:
http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com

Re: [MBZ] Heat pump question

[OK Don via Mercedes]

Like this one? Might keep an 8X8X8 well house above freezing with -10°F
temps? Your like went to a 30W incandescent bulb:
https://lanternnet.com/product/dietz-80-blizzard-cold-blast-lantern/


On Tue, Feb 16, 2021 at 3:04 PM Curt Raymond via Mercedes <
mercedes@okiebenz.com> wrote:

>  A look at Craigslist/yard sales/flea markets will yield loads of these
> tubular lanterns.
>
> Jim's link is a cold blast version, the doodad at the top takes air from
> outside, funnels it down those tubes where it gets to the flame. Cold blast
> lanterns make the most light for fuel volume in the flat wick lantern
> family.
>
> Alternately:
> https://lanternnet.com/product/dietz-10-monarch-hot-blast-lantern/That's
> a hot blast lantern, no doodad at the top, it recaptures a portion of the
> gasses coming from the burner and sends them back to the flame to be burned
> again. A hot blast lantern makes less light but uses less fuel since
> there's a little bit of unburned fuel in the output of the burner. Hot
> blast lanterns tend to burn longer per unit of fuel but put off less light.
> They also tend to make less smell if that's a consideration in your
> situation.
>
> For max light in a silent lamp you want:
> https://lanternnet.com/product/w-t-kirkman-ramona-table-lamp-w-500-aladdin-burner/
> which is a round wick lamp, the wick is a tube. On this one the wick heats
> a mantle for more light output. Probably not all that useful for the well
> house though, and kinda spendy.
> -Curt
>
> On Tuesday, February 16, 2021, 2:01:37 PM EST, Jim Cathey via Mercedes
>  wrote:
>
>  > I need a kerosene lamp - what/where do I get one? Recommendations
> please.
>
> What about:
> https://www.redhillgeneralstore.com/Oil-Lanterns/Camping-Oil-Lantern.htm?color=red
> <
> https://www.redhillgeneralstore.com/Oil-Lanterns/Camping-Oil-Lantern.htm?color=red
> >
>
> 45 hour burn time.
>
> -- Jim
>
> ___
> http://www.okiebenz.com
>
> To search list archives http://www.okiebenz.com/archive/
>
> To Unsubscribe or change delivery options go to:
> http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com
>
>
> ___
> http://www.okiebenz.com
>
> To search list archives http://www.okiebenz.com/archive/
>
> To Unsubscribe or change delivery options go to:
> http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com
>
>

-- 
OK Don

"Whenever you find yourself on the side of the majority, it is time to
pause and reflect." Mark Twain

“Basic research is what I’m doing when I don’t know what I am doing.”  Wernher
Von Braun
2013 F150, 18 mpg
2017 Subaru Legacy, 30 mpg
1957 C182A, 12 mpg - but at 150 mph!
___
http://www.okiebenz.com

To search list archives http://www.okiebenz.com/archive/

To Unsubscribe or change delivery options go to:
http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com

Re: [MBZ] Heat pump question

[Curt Raymond via Mercedes]

 A look at Craigslist/yard sales/flea markets will yield loads of these tubular 
lanterns.

Jim's link is a cold blast version, the doodad at the top takes air from 
outside, funnels it down those tubes where it gets to the flame. Cold blast 
lanterns make the most light for fuel volume in the flat wick lantern family.

Alternately: 
https://lanternnet.com/product/dietz-10-monarch-hot-blast-lantern/That's a hot 
blast lantern, no doodad at the top, it recaptures a portion of the gasses 
coming from the burner and sends them back to the flame to be burned again. A 
hot blast lantern makes less light but uses less fuel since there's a little 
bit of unburned fuel in the output of the burner. Hot blast lanterns tend to 
burn longer per unit of fuel but put off less light. They also tend to make 
less smell if that's a consideration in your situation.

For max light in a silent lamp you want: 
https://lanternnet.com/product/w-t-kirkman-ramona-table-lamp-w-500-aladdin-burner/
 which is a round wick lamp, the wick is a tube. On this one the wick heats a 
mantle for more light output. Probably not all that useful for the well house 
though, and kinda spendy.
-Curt

On Tuesday, February 16, 2021, 2:01:37 PM EST, Jim Cathey via Mercedes 
 wrote:  
 
 > I need a kerosene lamp - what/where do I get one? Recommendations please.

What about: 
https://www.redhillgeneralstore.com/Oil-Lanterns/Camping-Oil-Lantern.htm?color=red
 


45 hour burn time.

-- Jim

___
http://www.okiebenz.com

To search list archives http://www.okiebenz.com/archive/

To Unsubscribe or change delivery options go to:
http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com

  
___
http://www.okiebenz.com

To search list archives http://www.okiebenz.com/archive/

To Unsubscribe or change delivery options go to:
http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com

Re: [MBZ] Heat pump question

[Floyd Thursby via Mercedes]

Well you don't need to worry about food in the fridge going bad, just 
put it in boxes outside or on the porch.


Get one of those little 2 stroke generators from HF, they are like $90 
and will run your blowers fine.  They are quite handy too to keep in the 
truck to run a tool or air pump or something, you just need to run them 
every week or two or they get hard to start.


But a bigger generator would be good to have, you probably have to worry 
about tornadoes there that can knock out power for some extended time.


--FT

On 2/16/21 11:48 AM, Kaleb Striplin via Mercedes wrote:

I really need to look into a generator or some sort.


--
--FT

___
http://www.okiebenz.com

To search list archives http://www.okiebenz.com/archive/

To Unsubscribe or change delivery options go to:
http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com

Re: [MBZ] Heat pump question

[Jim Cathey via Mercedes]

> I need a kerosene lamp - what/where do I get one? Recommendations please.

What about: 
https://www.redhillgeneralstore.com/Oil-Lanterns/Camping-Oil-Lantern.htm?color=red
 


45 hour burn time.

-- Jim

___
http://www.okiebenz.com

To search list archives http://www.okiebenz.com/archive/

To Unsubscribe or change delivery options go to:
http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com

Re: [MBZ] Heat pump question

[Allan Streib via Mercedes]

Jim Cathey via Mercedes  writes:

>> I worry most about the well house freezing up - lots of pipe and two large
>> water filters in there. We keep it above freezing with those 500W IR heat
>> lamps, two for backup, but when there's no power ...
>
> Kerosene lamp.

Or even candles, assuming you can place them where they won't set
anything else on fire.

Allan

___
http://www.okiebenz.com

To search list archives http://www.okiebenz.com/archive/

To Unsubscribe or change delivery options go to:
http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com

Re: [MBZ] Heat pump question

[Jim Cathey via Mercedes]

> I worry most about the well house freezing up - lots of pipe and two large
> water filters in there. We keep it above freezing with those 500W IR heat
> lamps, two for backup, but when there's no power ...

Kerosene lamp.

-- Jim


___
http://www.okiebenz.com

To search list archives http://www.okiebenz.com/archive/

To Unsubscribe or change delivery options go to:
http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com

Re: [MBZ] Heat pump question

[Kaleb Striplin via Mercedes]

I was just thinking about that. I have a clamp on inverter around here 
somewhere. 

Sent from my iPhone

> On Feb 16, 2021, at 12:03 PM, OK Don via Mercedes  
> wrote:
> 
> Is the blower 120V? If so, use an inverter and a car battery to run it. If
> not 120V, use a 12V computer fan like Jim said. Zip tie it in front of the
> intake for the blower.
> 
> Our power was off for an hour this morning, since it was almost exactly an
> hour I assume it was a rolling blackout. It came back on in 3 spurts, but
> has stayed on now for over 3 hours.
> 
> I worry most about the well house freezing up - lots of pipe and two large
> water filters in there. We keep it above freezing with those 500W IR heat
> lamps, two for backup, but when there's no power ...
> 
>> On Tue, Feb 16, 2021 at 11:40 AM Kaleb Striplin via Mercedes <
>> mercedes@okiebenz.com> wrote:
>> 
>> It’s good and hot now. Fire going good, top of it is hot but unfortunately
>> without the blower it does not push much heat into the room. It’s now down
>> to 58 in here  by the maybe it’s putting off enough heat to keep it from
>> dropping faster than without it.
>> 
>> Sent from my iPhone
>> 
 On Feb 16, 2021, at 11:02 AM, Curt Raymond  wrote:
>>> 
>>> 
>>> Every year I go through a period of relearning how to get maximum output
>> from the stove. There are a couple rules but its really more an art than a
>> science. The quality of the wood makes a big difference as does outside
>> temps and, to a lesser degree, even wind speed and direction.
>>> 
>>> -Curt
>>> 
>>> On Tuesday, February 16, 2021, 11:54:32 AM EST, Kaleb Striplin via
>> Mercedes  wrote:
>>> 
>>> 
>>> It’s got an air control on each side, I can’t remember if they are
>> pushed in or pulled out to open are flow into it. They were pushed in and
>> it seemed like the fire was dying down with the doors closed so I pulled
>> them out. As I said it’s been a while since I have used this thing.
>>> 
>>> 
>>> 
>>> Sent from my iPhone
>>> 
 On Feb 16, 2021, at 10:49 AM, Kaleb Striplin 
>> wrote:
 
 Nope it’s all contained in the original brick chimney. I closed the
>> doors on it and will see what happens
 
 I really need to look into a generator or some sort.
 
 
>>> 
 
 
 Sent from my iPhone
 
>> On Feb 16, 2021, at 10:43 AM, Curt Raymond 
>> wrote:
>> 
> 
> The doors will probably make more heat, you're losing it up the
>> chimney because its getting too much air.
> 
> I've got a thermometer on the stove pipe and I'm always interested in
>> the fact that maximum heat is NOT achieved with maximum air. You've got to
>> run a lot of air to get the fire going and to get the stove/chimney warm
>> but then you need to restrict air some to get max heat. I don't completely
>> understand why but its a fact, at least in my stove. Some of the heat has
>> to go into the chimney, otherwise you won't be able to maintain good draft.
>> Outside chimneys might look cool but they suck for actually burning wood.
> 
> Do you have a pipe coming out of yours you can put a magnetic stove
>> thermometer on? Without one you'll produce less heat and burn way more wood
>> since you don't really know whats happening.
> 
> -Curt
> 
> On Tuesday, February 16, 2021, 11:36:05 AM EST, Kaleb Striplin via
>> Mercedes  wrote:
> 
> 
> Got the fire going. Of course it will take a while to start putting
>> off some heat. Without the doors closed and the blower going, it seems like
>> it’s probably operating like a regular fireplace with most of the heat
>> going ok the chimney.
> 
> Sent from my iPhone
> 
>> On Feb 16, 2021, at 10:07 AM, Curt Raymond 
>> wrote:
>> 
>> 
>> Some of those units do pretty amazing things in the cold these
>> days. 10-15 years ago 20F was the practical minimum but I've read of units
>> that will still work down to 0F and there are some that probably go colder.
>> I suspect efficiency takes a dump at those temps though.
>> 
>> The guy I'm training to run the groomer is an HVAC installer and
>> the other night he was telling me that just about nobody is installing
>> ground source heat pumps any more due to the huge cost and the availability
>> of low temp air source units combined with the low cost of natural gas.
>> 
>> I'd considered ground source but the ones I've looked at are
>> $20,000+ while a new boiler for our house is more like $6,000 and would
>> decrease our oil use 20-25%. It would take a long long time to pay off that
>> extra cost. There are incentives but they're decreasing every year.
>> 
>> -Curt
>> 
>> On Tuesday, February 16, 2021, 10:46:10 AM EST, Kaleb Striplin via
>> Mercedes  wrote:
>> 
>> 
>> I don’t know if size matters but it’s a 5 ton unit and even when it
>> was in the single digest I could tell it was putting out heat. I could tell
>> the difference between when the outside unit was running and when 

Re: [MBZ] Heat pump question

[OK Don via Mercedes]

Is the blower 120V? If so, use an inverter and a car battery to run it. If
not 120V, use a 12V computer fan like Jim said. Zip tie it in front of the
intake for the blower.

Our power was off for an hour this morning, since it was almost exactly an
hour I assume it was a rolling blackout. It came back on in 3 spurts, but
has stayed on now for over 3 hours.

I worry most about the well house freezing up - lots of pipe and two large
water filters in there. We keep it above freezing with those 500W IR heat
lamps, two for backup, but when there's no power ...

On Tue, Feb 16, 2021 at 11:40 AM Kaleb Striplin via Mercedes <
mercedes@okiebenz.com> wrote:

> It’s good and hot now. Fire going good, top of it is hot but unfortunately
> without the blower it does not push much heat into the room. It’s now down
> to 58 in here  by the maybe it’s putting off enough heat to keep it from
> dropping faster than without it.
>
> Sent from my iPhone
>
> > On Feb 16, 2021, at 11:02 AM, Curt Raymond  wrote:
> >
> > 
> > Every year I go through a period of relearning how to get maximum output
> from the stove. There are a couple rules but its really more an art than a
> science. The quality of the wood makes a big difference as does outside
> temps and, to a lesser degree, even wind speed and direction.
> >
> > -Curt
> >
> > On Tuesday, February 16, 2021, 11:54:32 AM EST, Kaleb Striplin via
> Mercedes  wrote:
> >
> >
> > It’s got an air control on each side, I can’t remember if they are
> pushed in or pulled out to open are flow into it. They were pushed in and
> it seemed like the fire was dying down with the doors closed so I pulled
> them out. As I said it’s been a while since I have used this thing.
> >
> >
> >
> > Sent from my iPhone
> >
> > > On Feb 16, 2021, at 10:49 AM, Kaleb Striplin 
> wrote:
> > >
> > > Nope it’s all contained in the original brick chimney. I closed the
> doors on it and will see what happens
> > >
> > > I really need to look into a generator or some sort.
> > >
> > > 
> >
> > >
> > >
> > > Sent from my iPhone
> > >
> > >>> On Feb 16, 2021, at 10:43 AM, Curt Raymond 
> wrote:
> > >>>
> > >> 
> > >> The doors will probably make more heat, you're losing it up the
> chimney because its getting too much air.
> > >>
> > >> I've got a thermometer on the stove pipe and I'm always interested in
> the fact that maximum heat is NOT achieved with maximum air. You've got to
> run a lot of air to get the fire going and to get the stove/chimney warm
> but then you need to restrict air some to get max heat. I don't completely
> understand why but its a fact, at least in my stove. Some of the heat has
> to go into the chimney, otherwise you won't be able to maintain good draft.
> Outside chimneys might look cool but they suck for actually burning wood.
> > >>
> > >> Do you have a pipe coming out of yours you can put a magnetic stove
> thermometer on? Without one you'll produce less heat and burn way more wood
> since you don't really know whats happening.
> > >>
> > >> -Curt
> > >>
> > >> On Tuesday, February 16, 2021, 11:36:05 AM EST, Kaleb Striplin via
> Mercedes  wrote:
> > >>
> > >>
> > >> Got the fire going. Of course it will take a while to start putting
> off some heat. Without the doors closed and the blower going, it seems like
> it’s probably operating like a regular fireplace with most of the heat
> going ok the chimney.
> > >>
> > >> Sent from my iPhone
> > >>
> > >> > On Feb 16, 2021, at 10:07 AM, Curt Raymond 
> wrote:
> > >> >
> > >> > 
> > >> > Some of those units do pretty amazing things in the cold these
> days. 10-15 years ago 20F was the practical minimum but I've read of units
> that will still work down to 0F and there are some that probably go colder.
> I suspect efficiency takes a dump at those temps though.
> > >> >
> > >> > The guy I'm training to run the groomer is an HVAC installer and
> the other night he was telling me that just about nobody is installing
> ground source heat pumps any more due to the huge cost and the availability
> of low temp air source units combined with the low cost of natural gas.
> > >> >
> > >> > I'd considered ground source but the ones I've looked at are
> $20,000+ while a new boiler for our house is more like $6,000 and would
> decrease our oil use 20-25%. It would take a long long time to pay off that
> extra cost. There are incentives but they're decreasing every year.
> > >> >
> > >> > -Curt
> > >> >
> > >> > On Tuesday, February 16, 2021, 10:46:10 AM EST, Kaleb Striplin via
> Mercedes  wrote:
> > >> >
> > >> >
> > >> > I don’t know if size matters but it’s a 5 ton unit and even when it
> was in the single digest I could tell it was putting out heat. I could tell
> the difference between when the outside unit was running and when it was
> shut down and only using the aux heat.
> > >> >
> > >> > Sent from my iPhone
> > >> >
> > >> > > On Feb 16, 2021, at 9:44 AM, Floyd Thursby via Mercedes <
> mercedes@okiebenz.com> wrote:
> > >> > >
> > >> > > There'

Re: [MBZ] Heat pump question

[Kaleb Striplin via Mercedes]

I think for now I at least need to get some sort of portable generator. Worse 
case I could have run an extension cord into the house to run the thing. 

Sent from my iPhone

> On Feb 16, 2021, at 11:52 AM, Jim Cathey  wrote:
> 
> 
>> 
>> an insert with a blower but I guess it will still out out some heat without 
>> the blower.
> 
> No, not much.  Better than nothing, but not by much.  Add a 12V computer fan 
> and a car
> battery to the mix and you'd actually get some heat out of it.  The heating 
> units designed
> for forced air just don't do much by natural convection.  They can keep their 
> own fires
> going, but most of the heat just doesn't get out into the room.
> 
> -- Jim
> 


___
http://www.okiebenz.com

To search list archives http://www.okiebenz.com/archive/

To Unsubscribe or change delivery options go to:
http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com

Re: [MBZ] Heat pump question

[Kaleb Striplin via Mercedes]

Power just came back on, for now. Plugged the blower in and she is throwing out 
a lot of heat. Also the heat pump kicked back on, outside unit and all. It’s 
now up to 6 outside and those instructions said when it got above 5 the lockout 
should end so I guess it was just doing what it was supposed to do. 

Since I have this fire going I’m probably going to keep feeding it. In fact 
this pile of wood I have out back is probably about 5 years old. Maybe I should 
just go ahead and use it all up this year and get fresh wood next year. I don’t 
want it to completely rot and go to waste. 
I also have lots from a a huge tree that blew down at the other house I cut up. 
Just need to split it. 

Sent from my iPhone

> On Feb 16, 2021, at 11:44 AM, Curt Raymond  wrote:
> 
> 
> It takes awhile for the stove and chimney to heat up to the point you really 
> radiate heat.
> The stove we have at camp (An "All Nighter" which is a copy of a Fisher) has 
> around 100# of firebrick inside. The first hour its lit from cold you're just 
> heating the stove, after that you start to heat the room. The stove stays hot 
> for hours after it goes out though. It's annoying when you first get to camp 
> and the place is freezing cold and the stove isn't helping. We've got a Big 
> Buddy propane heater on hand just for those sort of times. By the time its 
> burned through 2x 1# propane cans the stove is starting to radiate heat.
> 
> -Curt
> 
> On Tuesday, February 16, 2021, 12:40:35 PM EST, Kaleb Striplin via Mercedes 
>  wrote:
> 
> 
> It’s good and hot now. Fire going good, top of it is hot but unfortunately 
> without the blower it does not push much heat into the room. It’s now down to 
> 58 in here  by the maybe it’s putting off enough heat to keep it from 
> dropping faster than without it. 
> 
> Sent from my iPhone
> 
> > On Feb 16, 2021, at 11:02 AM, Curt Raymond  wrote:
> > 
> > 
> > Every year I go through a period of relearning how to get maximum output 
> > from the stove. There are a couple rules but its really more an art than a 
> > science. The quality of the wood makes a big difference as does outside 
> > temps and, to a lesser degree, even wind speed and direction.
> > 
> > -Curt
> > 
> > On Tuesday, February 16, 2021, 11:54:32 AM EST, Kaleb Striplin via Mercedes 
> >  wrote:
> > 
> > 
> > It’s got an air control on each side, I can’t remember if they are pushed 
> > in or pulled out to open are flow into it. They were pushed in and it 
> > seemed like the fire was dying down with the doors closed so I pulled them 
> > out. As I said it’s been a while since I have used this thing. 
> > 
> > 
> > 
> > Sent from my iPhone
> > 
> > > On Feb 16, 2021, at 10:49 AM, Kaleb Striplin  wrote:
> > > 
> > > Nope it’s all contained in the original brick chimney. I closed the 
> > > doors on it and will see what happens
> > > 
> > > I really need to look into a generator or some sort. 
> > > 
> > > 
> > 
> > > 
> > > 
> > > Sent from my iPhone
> > > 
> > >>> On Feb 16, 2021, at 10:43 AM, Curt Raymond  wrote:
> > >>> 
> > >> 
> > >> The doors will probably make more heat, you're losing it up the chimney 
> > >> because its getting too much air.
> > >> 
> > >> I've got a thermometer on the stove pipe and I'm always interested in 
> > >> the fact that maximum heat is NOT achieved with maximum air. You've got 
> > >> to run a lot of air to get the fire going and to get the stove/chimney 
> > >> warm but then you need to restrict air some to get max heat. I don't 
> > >> completely understand why but its a fact, at least in my stove. Some of 
> > >> the heat has to go into the chimney, otherwise you won't be able to 
> > >> maintain good draft. Outside chimneys might look cool but they suck for 
> > >> actually burning wood.
> > >> 
> > >> Do you have a pipe coming out of yours you can put a magnetic stove 
> > >> thermometer on? Without one you'll produce less heat and burn way more 
> > >> wood since you don't really know whats happening.
> > >> 
> > >> -Curt
> > >> 
> > >> On Tuesday, February 16, 2021, 11:36:05 AM EST, Kaleb Striplin via 
> > >> Mercedes  wrote:
> > >> 
> > >> 
> > >> Got the fire going. Of course it will take a while to start putting off 
> > >> some heat. Without the doors closed and the blower going, it seems like 
> > >> it’s probably operating like a regular fireplace with most of the heat 
> > >> going ok the chimney. 
> > >> 
> > >> Sent from my iPhone
> > >> 
> > >> > On Feb 16, 2021, at 10:07 AM, Curt Raymond  
> > >> > wrote:
> > >> > 
> > >> > 
> > >> > Some of those units do pretty amazing things in the cold these days. 
> > >> > 10-15 years ago 20F was the practical minimum but I've read of units 
> > >> > that will still work down to 0F and there are some that probably go 
> > >> > colder. I suspect efficiency takes a dump at those temps though.
> > >> > 
> > >> > The guy I'm training to run the groomer is an HVAC installer and the 
> > >> > other night he was telling me that just about no

Re: [MBZ] Heat pump question

[Jim Cathey via Mercedes]

> an insert with a blower but I guess it will still out out some heat without 
> the blower.

No, not much.  Better than nothing, but not by much.  Add a 12V computer fan 
and a car
battery to the mix and you'd actually get some heat out of it.  The heating 
units designed
for forced air just don't do much by natural convection.  They can keep their 
own fires
going, but most of the heat just doesn't get out into the room.

-- Jim


___
http://www.okiebenz.com

To search list archives http://www.okiebenz.com/archive/

To Unsubscribe or change delivery options go to:
http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com

Re: [MBZ] Heat pump question

[Curt Raymond via Mercedes]

 It takes awhile for the stove and chimney to heat up to the point you really 
radiate heat.The stove we have at camp (An "All Nighter" which is a copy of a 
Fisher) has around 100# of firebrick inside. The first hour its lit from cold 
you're just heating the stove, after that you start to heat the room. The stove 
stays hot for hours after it goes out though. It's annoying when you first get 
to camp and the place is freezing cold and the stove isn't helping. We've got a 
Big Buddy propane heater on hand just for those sort of times. By the time its 
burned through 2x 1# propane cans the stove is starting to radiate heat.

-Curt

On Tuesday, February 16, 2021, 12:40:35 PM EST, Kaleb Striplin via Mercedes 
 wrote:  
 
 It’s good and hot now. Fire going good, top of it is hot but unfortunately 
without the blower it does not push much heat into the room. It’s now down to 
58 in here  by the maybe it’s putting off enough heat to keep it from dropping 
faster than without it. 

Sent from my iPhone

> On Feb 16, 2021, at 11:02 AM, Curt Raymond  wrote:
> 
> 
> Every year I go through a period of relearning how to get maximum output from 
> the stove. There are a couple rules but its really more an art than a 
> science. The quality of the wood makes a big difference as does outside temps 
> and, to a lesser degree, even wind speed and direction.
> 
> -Curt
> 
> On Tuesday, February 16, 2021, 11:54:32 AM EST, Kaleb Striplin via Mercedes 
>  wrote:
> 
> 
> It’s got an air control on each side, I can’t remember if they are pushed in 
> or pulled out to open are flow into it. They were pushed in and it seemed 
> like the fire was dying down with the doors closed so I pulled them out. As I 
> said it’s been a while since I have used this thing. 
> 
> 
> 
> Sent from my iPhone
> 
> > On Feb 16, 2021, at 10:49 AM, Kaleb Striplin  wrote:
> > 
> > Nope it’s all contained in the original brick chimney. I closed the doors 
> > on it and will see what happens
> > 
> > I really need to look into a generator or some sort. 
> > 
> > 
> 
> > 
> > 
> > Sent from my iPhone
> > 
> >>> On Feb 16, 2021, at 10:43 AM, Curt Raymond  wrote:
> >>> 
> >> 
> >> The doors will probably make more heat, you're losing it up the chimney 
> >> because its getting too much air.
> >> 
> >> I've got a thermometer on the stove pipe and I'm always interested in the 
> >> fact that maximum heat is NOT achieved with maximum air. You've got to run 
> >> a lot of air to get the fire going and to get the stove/chimney warm but 
> >> then you need to restrict air some to get max heat. I don't completely 
> >> understand why but its a fact, at least in my stove. Some of the heat has 
> >> to go into the chimney, otherwise you won't be able to maintain good 
> >> draft. Outside chimneys might look cool but they suck for actually burning 
> >> wood.
> >> 
> >> Do you have a pipe coming out of yours you can put a magnetic stove 
> >> thermometer on? Without one you'll produce less heat and burn way more 
> >> wood since you don't really know whats happening.
> >> 
> >> -Curt
> >> 
> >> On Tuesday, February 16, 2021, 11:36:05 AM EST, Kaleb Striplin via 
> >> Mercedes  wrote:
> >> 
> >> 
> >> Got the fire going. Of course it will take a while to start putting off 
> >> some heat. Without the doors closed and the blower going, it seems like 
> >> it’s probably operating like a regular fireplace with most of the heat 
> >> going ok the chimney. 
> >> 
> >> Sent from my iPhone
> >> 
> >> > On Feb 16, 2021, at 10:07 AM, Curt Raymond  wrote:
> >> > 
> >> > 
> >> > Some of those units do pretty amazing things in the cold these days. 
> >> > 10-15 years ago 20F was the practical minimum but I've read of units 
> >> > that will still work down to 0F and there are some that probably go 
> >> > colder. I suspect efficiency takes a dump at those temps though.
> >> > 
> >> > The guy I'm training to run the groomer is an HVAC installer and the 
> >> > other night he was telling me that just about nobody is installing 
> >> > ground source heat pumps any more due to the huge cost and the 
> >> > availability of low temp air source units combined with the low cost of 
> >> > natural gas.
> >> > 
> >> > I'd considered ground source but the ones I've looked at are $20,000+ 
> >> > while a new boiler for our house is more like $6,000 and would decrease 
> >> > our oil use 20-25%. It would take a long long time to pay off that extra 
> >> > cost. There are incentives but they're decreasing every year.
> >> > 
> >> > -Curt
> >> > 
> >> > On Tuesday, February 16, 2021, 10:46:10 AM EST, Kaleb Striplin via 
> >> > Mercedes  wrote:
> >> > 
> >> > 
> >> > I don’t know if size matters but it’s a 5 ton unit and even when it was 
> >> > in the single digest I could tell it was putting out heat. I could tell 
> >> > the difference between when the outside unit was running and when it was 
> >> > shut down and only using the aux heat.
> >> > 
> >> > Sent from my iPhone
> >> > 
> >>

Re: [MBZ] Heat pump question

[Curt Raymond via Mercedes]

 Well that's weird. I don't think I've ever seen a carb fail while the engine 
was running.My little generator has a real actual carb bowl. I was surprised 
when I found that, I figured it'd be more like a Tillotson or Walbro carb on a 
snowmobile or chainsaw that has just a small space that acts like a bowl.
A real bowl is way better, it accumulates water and crud that you can dump out 
later rather than trying to suck it through the jet immediately.
-Curt

On Tuesday, February 16, 2021, 12:03:32 PM EST, Mitch Haley via Mercedes 
 wrote:  
 
 On 2021-02-16 10:58, Curt Raymond via Mercedes wrote:
> I've got a 1200w 2 stroke generator that has never been used "in
> anger". It outputs 12v also which can be handy.It would be super
> useful for you now as it would easily run your blower and just sip
> fuel. Its supposed to run 8 hours at half load on 1 gallon of gas.

I ran a 850W (1000 peak) unattended overnight last spring with a freezer 
hooked up to it.
One morning I found it dead in a greasy spot on the concrete, started to 
refuel it and saw the premix leaking out of the carb at an alarming 
rate. Need to pull the float bowl off and see what failed.

___
http://www.okiebenz.com

To search list archives http://www.okiebenz.com/archive/

To Unsubscribe or change delivery options go to:
http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com

  
___
http://www.okiebenz.com

To search list archives http://www.okiebenz.com/archive/

To Unsubscribe or change delivery options go to:
http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com

Re: [MBZ] Heat pump question

[Kaleb Striplin via Mercedes]

It’s good and hot now. Fire going good, top of it is hot but unfortunately 
without the blower it does not push much heat into the room. It’s now down to 
58 in here  by the maybe it’s putting off enough heat to keep it from dropping 
faster than without it. 

Sent from my iPhone

> On Feb 16, 2021, at 11:02 AM, Curt Raymond  wrote:
> 
> 
> Every year I go through a period of relearning how to get maximum output from 
> the stove. There are a couple rules but its really more an art than a 
> science. The quality of the wood makes a big difference as does outside temps 
> and, to a lesser degree, even wind speed and direction.
> 
> -Curt
> 
> On Tuesday, February 16, 2021, 11:54:32 AM EST, Kaleb Striplin via Mercedes 
>  wrote:
> 
> 
> It’s got an air control on each side, I can’t remember if they are pushed in 
> or pulled out to open are flow into it. They were pushed in and it seemed 
> like the fire was dying down with the doors closed so I pulled them out. As I 
> said it’s been a while since I have used this thing. 
> 
> 
> 
> Sent from my iPhone
> 
> > On Feb 16, 2021, at 10:49 AM, Kaleb Striplin  wrote:
> > 
> > Nope it’s all contained in the original brick chimney. I closed the doors 
> > on it and will see what happens
> > 
> > I really need to look into a generator or some sort. 
> > 
> > 
> 
> > 
> > 
> > Sent from my iPhone
> > 
> >>> On Feb 16, 2021, at 10:43 AM, Curt Raymond  wrote:
> >>> 
> >> 
> >> The doors will probably make more heat, you're losing it up the chimney 
> >> because its getting too much air.
> >> 
> >> I've got a thermometer on the stove pipe and I'm always interested in the 
> >> fact that maximum heat is NOT achieved with maximum air. You've got to run 
> >> a lot of air to get the fire going and to get the stove/chimney warm but 
> >> then you need to restrict air some to get max heat. I don't completely 
> >> understand why but its a fact, at least in my stove. Some of the heat has 
> >> to go into the chimney, otherwise you won't be able to maintain good 
> >> draft. Outside chimneys might look cool but they suck for actually burning 
> >> wood.
> >> 
> >> Do you have a pipe coming out of yours you can put a magnetic stove 
> >> thermometer on? Without one you'll produce less heat and burn way more 
> >> wood since you don't really know whats happening.
> >> 
> >> -Curt
> >> 
> >> On Tuesday, February 16, 2021, 11:36:05 AM EST, Kaleb Striplin via 
> >> Mercedes  wrote:
> >> 
> >> 
> >> Got the fire going. Of course it will take a while to start putting off 
> >> some heat. Without the doors closed and the blower going, it seems like 
> >> it’s probably operating like a regular fireplace with most of the heat 
> >> going ok the chimney. 
> >> 
> >> Sent from my iPhone
> >> 
> >> > On Feb 16, 2021, at 10:07 AM, Curt Raymond  wrote:
> >> > 
> >> > 
> >> > Some of those units do pretty amazing things in the cold these days. 
> >> > 10-15 years ago 20F was the practical minimum but I've read of units 
> >> > that will still work down to 0F and there are some that probably go 
> >> > colder. I suspect efficiency takes a dump at those temps though.
> >> > 
> >> > The guy I'm training to run the groomer is an HVAC installer and the 
> >> > other night he was telling me that just about nobody is installing 
> >> > ground source heat pumps any more due to the huge cost and the 
> >> > availability of low temp air source units combined with the low cost of 
> >> > natural gas.
> >> > 
> >> > I'd considered ground source but the ones I've looked at are $20,000+ 
> >> > while a new boiler for our house is more like $6,000 and would decrease 
> >> > our oil use 20-25%. It would take a long long time to pay off that extra 
> >> > cost. There are incentives but they're decreasing every year.
> >> > 
> >> > -Curt
> >> > 
> >> > On Tuesday, February 16, 2021, 10:46:10 AM EST, Kaleb Striplin via 
> >> > Mercedes  wrote:
> >> > 
> >> > 
> >> > I don’t know if size matters but it’s a 5 ton unit and even when it was 
> >> > in the single digest I could tell it was putting out heat. I could tell 
> >> > the difference between when the outside unit was running and when it was 
> >> > shut down and only using the aux heat.
> >> > 
> >> > Sent from my iPhone
> >> > 
> >> > > On Feb 16, 2021, at 9:44 AM, Floyd Thursby via Mercedes 
> >> > >  wrote:
> >> > > 
> >> > > There's no point in it running if it can't extract any heat from the 
> >> > > air.  It's a wonder it was running and putting out much when it got 
> >> > > down below 20F or so.
> >> > > 
> >> > > --FT
> >> > > 
> >> > >> On 2/16/21 10:36 AM, Kaleb Striplin via Mercedes wrote:
> >> > >> Power just came back on a few minutes ago.  Outside unit still not 
> >> > >> running.  I did find the installation manual online though. Here is 
> >> > >> some info about the defrost and lockouts.  Sounds like it may simply 
> >> > >> be locking out because the temp is too low.
> >> > >> 
> >> > >> Heating Mode:The compressor and fan motor wi

Re: [MBZ] Heat pump question

[Mitch Haley via Mercedes]

On 2021-02-16 10:58, Curt Raymond via Mercedes wrote:

I've got a 1200w 2 stroke generator that has never been used "in
anger". It outputs 12v also which can be handy.It would be super
useful for you now as it would easily run your blower and just sip
fuel. Its supposed to run 8 hours at half load on 1 gallon of gas.


I ran a 850W (1000 peak) unattended overnight last spring with a freezer 
hooked up to it.
One morning I found it dead in a greasy spot on the concrete, started to 
refuel it and saw the premix leaking out of the carb at an alarming 
rate. Need to pull the float bowl off and see what failed.


___
http://www.okiebenz.com

To search list archives http://www.okiebenz.com/archive/

To Unsubscribe or change delivery options go to:
http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com

Re: [MBZ] Heat pump question

[Curt Raymond via Mercedes]

 Every year I go through a period of relearning how to get maximum output from 
the stove. There are a couple rules but its really more an art than a science. 
The quality of the wood makes a big difference as does outside temps and, to a 
lesser degree, even wind speed and direction.
-Curt

On Tuesday, February 16, 2021, 11:54:32 AM EST, Kaleb Striplin via Mercedes 
 wrote:  
 
 It’s got an air control on each side, I can’t remember if they are pushed in 
or pulled out to open are flow into it. They were pushed in and it seemed like 
the fire was dying down with the doors closed so I pulled them out. As I said 
it’s been a while since I have used this thing. 



Sent from my iPhone

> On Feb 16, 2021, at 10:49 AM, Kaleb Striplin  wrote:
> 
> Nope it’s all contained in the original brick chimney. I closed the doors on 
> it and will see what happens
> 
> I really need to look into a generator or some sort. 
> 
> 
> 
> 
> Sent from my iPhone
> 
>>> On Feb 16, 2021, at 10:43 AM, Curt Raymond  wrote:
>>> 
>> 
>> The doors will probably make more heat, you're losing it up the chimney 
>> because its getting too much air.
>> 
>> I've got a thermometer on the stove pipe and I'm always interested in the 
>> fact that maximum heat is NOT achieved with maximum air. You've got to run a 
>> lot of air to get the fire going and to get the stove/chimney warm but then 
>> you need to restrict air some to get max heat. I don't completely understand 
>> why but its a fact, at least in my stove. Some of the heat has to go into 
>> the chimney, otherwise you won't be able to maintain good draft. Outside 
>> chimneys might look cool but they suck for actually burning wood.
>> 
>> Do you have a pipe coming out of yours you can put a magnetic stove 
>> thermometer on? Without one you'll produce less heat and burn way more wood 
>> since you don't really know whats happening.
>> 
>> -Curt
>> 
>> On Tuesday, February 16, 2021, 11:36:05 AM EST, Kaleb Striplin via Mercedes 
>>  wrote:
>> 
>> 
>> Got the fire going. Of course it will take a while to start putting off some 
>> heat. Without the doors closed and the blower going, it seems like it’s 
>> probably operating like a regular fireplace with most of the heat going ok 
>> the chimney. 
>> 
>> Sent from my iPhone
>> 
>> > On Feb 16, 2021, at 10:07 AM, Curt Raymond  wrote:
>> > 
>> > 
>> > Some of those units do pretty amazing things in the cold these days. 10-15 
>> > years ago 20F was the practical minimum but I've read of units that will 
>> > still work down to 0F and there are some that probably go colder. I 
>> > suspect efficiency takes a dump at those temps though.
>> > 
>> > The guy I'm training to run the groomer is an HVAC installer and the other 
>> > night he was telling me that just about nobody is installing ground source 
>> > heat pumps any more due to the huge cost and the availability of low temp 
>> > air source units combined with the low cost of natural gas.
>> > 
>> > I'd considered ground source but the ones I've looked at are $20,000+ 
>> > while a new boiler for our house is more like $6,000 and would decrease 
>> > our oil use 20-25%. It would take a long long time to pay off that extra 
>> > cost. There are incentives but they're decreasing every year.
>> > 
>> > -Curt
>> > 
>> > On Tuesday, February 16, 2021, 10:46:10 AM EST, Kaleb Striplin via 
>> > Mercedes  wrote:
>> > 
>> > 
>> > I don’t know if size matters but it’s a 5 ton unit and even when it was in 
>> > the single digest I could tell it was putting out heat. I could tell the 
>> > difference between when the outside unit was running and when it was shut 
>> > down and only using the aux heat.
>> > 
>> > Sent from my iPhone
>> > 
>> > > On Feb 16, 2021, at 9:44 AM, Floyd Thursby via Mercedes 
>> > >  wrote:
>> > > 
>> > > There's no point in it running if it can't extract any heat from the 
>> > > air.  It's a wonder it was running and putting out much when it got down 
>> > > below 20F or so.
>> > > 
>> > > --FT
>> > > 
>> > >> On 2/16/21 10:36 AM, Kaleb Striplin via Mercedes wrote:
>> > >> Power just came back on a few minutes ago.  Outside unit still not 
>> > >> running.  I did find the installation manual online though. Here is 
>> > >> some info about the defrost and lockouts.  Sounds like it may simply be 
>> > >> locking out because the temp is too low.
>> > >> 
>> > >> Heating Mode:The compressor and fan motor will stop when the low 
>> > >> pressure control opens and will start again when the low side pressure 
>> > >> rises to approximately 40 psig when the low pressure automatically 
>> > >> resets�If the low pressure switch trips 3 times within 120 minutes of 
>> > >> operation during a particular call for heating operation, the defrost 
>> > >> control will lock out compressor and outdoor fan operation�If the lock 
>> > >> out due to low pressure occurs at an outdoor ambient temperature below 
>> > >> 5°F, the defrost control will automatically exit the lockout mode wh

Re: [MBZ] Heat pump question

[Curt Raymond via Mercedes]

 I've got a 1200w 2 stroke generator that has never been used "in anger". It 
outputs 12v also which can be handy.It would be super useful for you now as it 
would easily run your blower and just sip fuel. Its supposed to run 8 hours at 
half load on 1 gallon of gas.
A Honda 2000w would be better but also would be 5x the cost and considering 
I've never really needed mine I can't justify it.I have considered the Harbor 
Freight copy to have at camp. When we were up there last July it was stiflingly 
hot. Dad wants to get a small air conditioner but the 3000w "Champion" 
generator we have now is quite loud.Google suggests that a 5000BTU aircon needs 
550w/hr so the small "super quiet" generator from Harbor Freight would do the 
job easily. We've got 500 or so sqft. of camp. It wouldn't make ice cubes 
inside but would certainly take the edge off.
-Curt



On Tuesday, February 16, 2021, 11:49:02 AM EST, Kaleb Striplin via Mercedes 
 wrote:  
 
 Nope it’s all contained in the original brick chimney. I closed the doors on 
it and will see what happens

I really need to look into a generator or some sort. 



Sent from my iPhone

> On Feb 16, 2021, at 10:43 AM, Curt Raymond  wrote:
> 
> 
> The doors will probably make more heat, you're losing it up the chimney 
> because its getting too much air.
> 
> I've got a thermometer on the stove pipe and I'm always interested in the 
> fact that maximum heat is NOT achieved with maximum air. You've got to run a 
> lot of air to get the fire going and to get the stove/chimney warm but then 
> you need to restrict air some to get max heat. I don't completely understand 
> why but its a fact, at least in my stove. Some of the heat has to go into the 
> chimney, otherwise you won't be able to maintain good draft. Outside chimneys 
> might look cool but they suck for actually burning wood.
> 
> Do you have a pipe coming out of yours you can put a magnetic stove 
> thermometer on? Without one you'll produce less heat and burn way more wood 
> since you don't really know whats happening.
> 
> -Curt
> 
> On Tuesday, February 16, 2021, 11:36:05 AM EST, Kaleb Striplin via Mercedes 
>  wrote:
> 
> 
> Got the fire going. Of course it will take a while to start putting off some 
> heat. Without the doors closed and the blower going, it seems like it’s 
> probably operating like a regular fireplace with most of the heat going ok 
> the chimney. 
> 
> Sent from my iPhone
> 
> > On Feb 16, 2021, at 10:07 AM, Curt Raymond  wrote:
> > 
> > 
> > Some of those units do pretty amazing things in the cold these days. 10-15 
> > years ago 20F was the practical minimum but I've read of units that will 
> > still work down to 0F and there are some that probably go colder. I suspect 
> > efficiency takes a dump at those temps though.
> > 
> > The guy I'm training to run the groomer is an HVAC installer and the other 
> > night he was telling me that just about nobody is installing ground source 
> > heat pumps any more due to the huge cost and the availability of low temp 
> > air source units combined with the low cost of natural gas.
> > 
> > I'd considered ground source but the ones I've looked at are $20,000+ while 
> > a new boiler for our house is more like $6,000 and would decrease our oil 
> > use 20-25%. It would take a long long time to pay off that extra cost. 
> > There are incentives but they're decreasing every year.
> > 
> > -Curt
> > 
> > On Tuesday, February 16, 2021, 10:46:10 AM EST, Kaleb Striplin via Mercedes 
> >  wrote:
> > 
> > 
> > I don’t know if size matters but it’s a 5 ton unit and even when it was in 
> > the single digest I could tell it was putting out heat. I could tell the 
> > difference between when the outside unit was running and when it was shut 
> > down and only using the aux heat.
> > 
> > Sent from my iPhone
> > 
> > > On Feb 16, 2021, at 9:44 AM, Floyd Thursby via Mercedes 
> > >  wrote:
> > > 
> > > There's no point in it running if it can't extract any heat from the 
> > > air.  It's a wonder it was running and putting out much when it got down 
> > > below 20F or so.
> > > 
> > > --FT
> > > 
> > >> On 2/16/21 10:36 AM, Kaleb Striplin via Mercedes wrote:
> > >> Power just came back on a few minutes ago.  Outside unit still not 
> > >> running.  I did find the installation manual online though. Here is some 
> > >> info about the defrost and lockouts.  Sounds like it may simply be 
> > >> locking out because the temp is too low.
> > >> 
> > >> Heating Mode:The compressor and fan motor will stop when the low 
> > >> pressure control opens and will start again when the low side pressure 
> > >> rises to approximately 40 psig when the low pressure automatically 
> > >> resets�If the low pressure switch trips 3 times within 120 minutes of 
> > >> operation during a particular call for heating operation, the defrost 
> > >> control will lock out compressor and outdoor fan operation�If the lock 
> > >> out due to low pressure occurs at an outdoor ambie

Re: [MBZ] Heat pump question

[Kaleb Striplin via Mercedes]

It’s got an air control on each side, I can’t remember if they are pushed in or 
pulled out to open are flow into it. They were pushed in and it seemed like the 
fire was dying down with the doors closed so I pulled them out. As I said it’s 
been a while since I have used this thing. 



Sent from my iPhone

> On Feb 16, 2021, at 10:49 AM, Kaleb Striplin  wrote:
> 
> Nope it’s all contained in the original brick chimney. I closed the doors on 
> it and will see what happens
> 
> I really need to look into a generator or some sort. 
> 
> 
> 
> 
> Sent from my iPhone
> 
>>> On Feb 16, 2021, at 10:43 AM, Curt Raymond  wrote:
>>> 
>> 
>> The doors will probably make more heat, you're losing it up the chimney 
>> because its getting too much air.
>> 
>> I've got a thermometer on the stove pipe and I'm always interested in the 
>> fact that maximum heat is NOT achieved with maximum air. You've got to run a 
>> lot of air to get the fire going and to get the stove/chimney warm but then 
>> you need to restrict air some to get max heat. I don't completely understand 
>> why but its a fact, at least in my stove. Some of the heat has to go into 
>> the chimney, otherwise you won't be able to maintain good draft. Outside 
>> chimneys might look cool but they suck for actually burning wood.
>> 
>> Do you have a pipe coming out of yours you can put a magnetic stove 
>> thermometer on? Without one you'll produce less heat and burn way more wood 
>> since you don't really know whats happening.
>> 
>> -Curt
>> 
>> On Tuesday, February 16, 2021, 11:36:05 AM EST, Kaleb Striplin via Mercedes 
>>  wrote:
>> 
>> 
>> Got the fire going. Of course it will take a while to start putting off some 
>> heat. Without the doors closed and the blower going, it seems like it’s 
>> probably operating like a regular fireplace with most of the heat going ok 
>> the chimney. 
>> 
>> Sent from my iPhone
>> 
>> > On Feb 16, 2021, at 10:07 AM, Curt Raymond  wrote:
>> > 
>> > 
>> > Some of those units do pretty amazing things in the cold these days. 10-15 
>> > years ago 20F was the practical minimum but I've read of units that will 
>> > still work down to 0F and there are some that probably go colder. I 
>> > suspect efficiency takes a dump at those temps though.
>> > 
>> > The guy I'm training to run the groomer is an HVAC installer and the other 
>> > night he was telling me that just about nobody is installing ground source 
>> > heat pumps any more due to the huge cost and the availability of low temp 
>> > air source units combined with the low cost of natural gas.
>> > 
>> > I'd considered ground source but the ones I've looked at are $20,000+ 
>> > while a new boiler for our house is more like $6,000 and would decrease 
>> > our oil use 20-25%. It would take a long long time to pay off that extra 
>> > cost. There are incentives but they're decreasing every year.
>> > 
>> > -Curt
>> > 
>> > On Tuesday, February 16, 2021, 10:46:10 AM EST, Kaleb Striplin via 
>> > Mercedes  wrote:
>> > 
>> > 
>> > I don’t know if size matters but it’s a 5 ton unit and even when it was in 
>> > the single digest I could tell it was putting out heat. I could tell the 
>> > difference between when the outside unit was running and when it was shut 
>> > down and only using the aux heat.
>> > 
>> > Sent from my iPhone
>> > 
>> > > On Feb 16, 2021, at 9:44 AM, Floyd Thursby via Mercedes 
>> > >  wrote:
>> > > 
>> > > There's no point in it running if it can't extract any heat from the 
>> > > air.  It's a wonder it was running and putting out much when it got down 
>> > > below 20F or so.
>> > > 
>> > > --FT
>> > > 
>> > >> On 2/16/21 10:36 AM, Kaleb Striplin via Mercedes wrote:
>> > >> Power just came back on a few minutes ago.  Outside unit still not 
>> > >> running.  I did find the installation manual online though. Here is 
>> > >> some info about the defrost and lockouts.  Sounds like it may simply be 
>> > >> locking out because the temp is too low.
>> > >> 
>> > >> Heating Mode:The compressor and fan motor will stop when the low 
>> > >> pressure control opens and will start again when the low side pressure 
>> > >> rises to approximately 40 psig when the low pressure automatically 
>> > >> resets�If the low pressure switch trips 3 times within 120 minutes of 
>> > >> operation during a particular call for heating operation, the defrost 
>> > >> control will lock out compressor and outdoor fan operation�If the lock 
>> > >> out due to low pressure occurs at an outdoor ambient temperature below 
>> > >> 5°F, the defrost control will automatically exit the lockout mode when 
>> > >> the outdoor ambient temperature rises 5°F�This feature is necessary 
>> > >> since the low pressure control could possibly have opened due to the 
>> > >> outdoor ambient being very low rather than an actual system fault�
>> > >> 
>> > >> 
>> > >> Of course with the power being out I figure that would have caused the 
>> > >> lockout to reset at least for a while.  Will se

Re: [MBZ] Heat pump question

[Kaleb Striplin via Mercedes]

Nope it’s all contained in the original brick chimney. I closed the doors on it 
and will see what happens

I really need to look into a generator or some sort. 



Sent from my iPhone

> On Feb 16, 2021, at 10:43 AM, Curt Raymond  wrote:
> 
> 
> The doors will probably make more heat, you're losing it up the chimney 
> because its getting too much air.
> 
> I've got a thermometer on the stove pipe and I'm always interested in the 
> fact that maximum heat is NOT achieved with maximum air. You've got to run a 
> lot of air to get the fire going and to get the stove/chimney warm but then 
> you need to restrict air some to get max heat. I don't completely understand 
> why but its a fact, at least in my stove. Some of the heat has to go into the 
> chimney, otherwise you won't be able to maintain good draft. Outside chimneys 
> might look cool but they suck for actually burning wood.
> 
> Do you have a pipe coming out of yours you can put a magnetic stove 
> thermometer on? Without one you'll produce less heat and burn way more wood 
> since you don't really know whats happening.
> 
> -Curt
> 
> On Tuesday, February 16, 2021, 11:36:05 AM EST, Kaleb Striplin via Mercedes 
>  wrote:
> 
> 
> Got the fire going. Of course it will take a while to start putting off some 
> heat. Without the doors closed and the blower going, it seems like it’s 
> probably operating like a regular fireplace with most of the heat going ok 
> the chimney. 
> 
> Sent from my iPhone
> 
> > On Feb 16, 2021, at 10:07 AM, Curt Raymond  wrote:
> > 
> > 
> > Some of those units do pretty amazing things in the cold these days. 10-15 
> > years ago 20F was the practical minimum but I've read of units that will 
> > still work down to 0F and there are some that probably go colder. I suspect 
> > efficiency takes a dump at those temps though.
> > 
> > The guy I'm training to run the groomer is an HVAC installer and the other 
> > night he was telling me that just about nobody is installing ground source 
> > heat pumps any more due to the huge cost and the availability of low temp 
> > air source units combined with the low cost of natural gas.
> > 
> > I'd considered ground source but the ones I've looked at are $20,000+ while 
> > a new boiler for our house is more like $6,000 and would decrease our oil 
> > use 20-25%. It would take a long long time to pay off that extra cost. 
> > There are incentives but they're decreasing every year.
> > 
> > -Curt
> > 
> > On Tuesday, February 16, 2021, 10:46:10 AM EST, Kaleb Striplin via Mercedes 
> >  wrote:
> > 
> > 
> > I don’t know if size matters but it’s a 5 ton unit and even when it was in 
> > the single digest I could tell it was putting out heat. I could tell the 
> > difference between when the outside unit was running and when it was shut 
> > down and only using the aux heat.
> > 
> > Sent from my iPhone
> > 
> > > On Feb 16, 2021, at 9:44 AM, Floyd Thursby via Mercedes 
> > >  wrote:
> > > 
> > > There's no point in it running if it can't extract any heat from the 
> > > air.  It's a wonder it was running and putting out much when it got down 
> > > below 20F or so.
> > > 
> > > --FT
> > > 
> > >> On 2/16/21 10:36 AM, Kaleb Striplin via Mercedes wrote:
> > >> Power just came back on a few minutes ago.  Outside unit still not 
> > >> running.  I did find the installation manual online though. Here is some 
> > >> info about the defrost and lockouts.  Sounds like it may simply be 
> > >> locking out because the temp is too low.
> > >> 
> > >> Heating Mode:The compressor and fan motor will stop when the low 
> > >> pressure control opens and will start again when the low side pressure 
> > >> rises to approximately 40 psig when the low pressure automatically 
> > >> resets�If the low pressure switch trips 3 times within 120 minutes of 
> > >> operation during a particular call for heating operation, the defrost 
> > >> control will lock out compressor and outdoor fan operation�If the lock 
> > >> out due to low pressure occurs at an outdoor ambient temperature below 
> > >> 5°F, the defrost control will automatically exit the lockout mode when 
> > >> the outdoor ambient temperature rises 5°F�This feature is necessary 
> > >> since the low pressure control could possibly have opened due to the 
> > >> outdoor ambient being very low rather than an actual system fault�
> > >> 
> > >> 
> > >> Of course with the power being out I figure that would have caused the 
> > >> lockout to reset at least for a while.  Will see what happens when it 
> > >> gets over 5 this afternoon.
> > > 
> > > ___
> > > http://www.okiebenz.com
> > > 
> > > To search list archives http://www.okiebenz.com/archive/
> > > 
> > > To Unsubscribe or change delivery options go to:
> > > http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com
> > 
> > > 
> > 
> > 
> > ___
> > http://www.okiebenz.com
> > 
> > To search list archives http://www.ok

Re: [MBZ] Heat pump question

[Curt Raymond via Mercedes]

 Closed, always with the doors closed. That's what allows you to control the 
air going in, otherwise all your warmed room air is going up the chimney.

-Curt

On Tuesday, February 16, 2021, 11:39:46 AM EST, Kaleb Striplin via Mercedes 
 wrote:  
 
 So got questions about these inserts. I have ran it before with the blower 
going and the doors closed and it will heat the house nicely. With no power 
should I run it with the doors open or closed? It’s burning pretty good now but 
seems like there is very little head coming off of it yet. 

Sent from my iPhone

> On Feb 16, 2021, at 10:36 AM, Kaleb Striplin  wrote:
> 
> Got the fire going. Of course it will take a while to start putting off some 
> heat. Without the doors closed and the blower going, it seems like it’s 
> probably operating like a regular fireplace with most of the heat going ok 
> the chimney. 
> 
> Sent from my iPhone
> 
>>> On Feb 16, 2021, at 10:07 AM, Curt Raymond  wrote:
>>> 
>> 
>> Some of those units do pretty amazing things in the cold these days. 10-15 
>> years ago 20F was the practical minimum but I've read of units that will 
>> still work down to 0F and there are some that probably go colder. I suspect 
>> efficiency takes a dump at those temps though.
>> 
>> The guy I'm training to run the groomer is an HVAC installer and the other 
>> night he was telling me that just about nobody is installing ground source 
>> heat pumps any more due to the huge cost and the availability of low temp 
>> air source units combined with the low cost of natural gas.
>> 
>> I'd considered ground source but the ones I've looked at are $20,000+ while 
>> a new boiler for our house is more like $6,000 and would decrease our oil 
>> use 20-25%. It would take a long long time to pay off that extra cost. There 
>> are incentives but they're decreasing every year.
>> 
>> -Curt
>> 
>> On Tuesday, February 16, 2021, 10:46:10 AM EST, Kaleb Striplin via Mercedes 
>>  wrote:
>> 
>> 
>> I don’t know if size matters but it’s a 5 ton unit and even when it was in 
>> the single digest I could tell it was putting out heat. I could tell the 
>> difference between when the outside unit was running and when it was shut 
>> down and only using the aux heat. 
>> 
>> Sent from my iPhone
>> 
>> > On Feb 16, 2021, at 9:44 AM, Floyd Thursby via Mercedes 
>> >  wrote:
>> > 
>> > There's no point in it running if it can't extract any heat from the air. 
>> >  It's a wonder it was running and putting out much when it got down below 
>> > 20F or so.
>> > 
>> > --FT
>> > 
>> >> On 2/16/21 10:36 AM, Kaleb Striplin via Mercedes wrote:
>> >> Power just came back on a few minutes ago.  Outside unit still not 
>> >> running.  I did find the installation manual online though. Here is some 
>> >> info about the defrost and lockouts.  Sounds like it may simply be 
>> >> locking out because the temp is too low.
>> >> 
>> >> Heating Mode:The compressor and fan motor will stop when the low pressure 
>> >> control opens and will start again when the low side pressure rises to 
>> >> approximately 40 psig when the low pressure automatically resets�If the 
>> >> low pressure switch trips 3 times within 120 minutes of operation during 
>> >> a particular call for heating operation, the defrost control will lock 
>> >> out compressor and outdoor fan operation�If the lock out due to low 
>> >> pressure occurs at an outdoor ambient temperature below 5°F, the defrost 
>> >> control will automatically exit the lockout mode when the outdoor ambient 
>> >> temperature rises 5°F�This feature is necessary since the low pressure 
>> >> control could possibly have opened due to the outdoor ambient being very 
>> >> low rather than an actual system fault�
>> >> 
>> >> 
>> >> Of course with the power being out I figure that would have caused the 
>> >> lockout to reset at least for a while.  Will see what happens when it 
>> >> gets over 5 this afternoon.
>> > 
>> > ___
>> > http://www.okiebenz.com
>> > 
>> > To search list archives http://www.okiebenz.com/archive/
>> > 
>> > To Unsubscribe or change delivery options go to:
>> > http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com
>> 
>> > 
>> 
>> 
>> ___
>> http://www.okiebenz.com
>> 
>> To search list archives http://www.okiebenz.com/archive/
>> 
>> To Unsubscribe or change delivery options go to:
>> http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com
>> 
___
http://www.okiebenz.com

To search list archives http://www.okiebenz.com/archive/

To Unsubscribe or change delivery options go to:
http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com

  
___
http://www.okiebenz.com

To search list archives http://www.okiebenz.com/archive/

To Unsubscribe or change delivery options go to:
http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com

Re: [MBZ] Heat pump question

[Curt Raymond via Mercedes]

 The doors will probably make more heat, you're losing it up the chimney 
because its getting too much air.
I've got a thermometer on the stove pipe and I'm always interested in the fact 
that maximum heat is NOT achieved with maximum air. You've got to run a lot of 
air to get the fire going and to get the stove/chimney warm but then you need 
to restrict air some to get max heat. I don't completely understand why but its 
a fact, at least in my stove. Some of the heat has to go into the chimney, 
otherwise you won't be able to maintain good draft. Outside chimneys might look 
cool but they suck for actually burning wood.

Do you have a pipe coming out of yours you can put a magnetic stove thermometer 
on? Without one you'll produce less heat and burn way more wood since you don't 
really know whats happening.
-Curt

On Tuesday, February 16, 2021, 11:36:05 AM EST, Kaleb Striplin via Mercedes 
 wrote:  
 
 Got the fire going. Of course it will take a while to start putting off some 
heat. Without the doors closed and the blower going, it seems like it’s 
probably operating like a regular fireplace with most of the heat going ok the 
chimney. 

Sent from my iPhone

> On Feb 16, 2021, at 10:07 AM, Curt Raymond  wrote:
> 
> 
> Some of those units do pretty amazing things in the cold these days. 10-15 
> years ago 20F was the practical minimum but I've read of units that will 
> still work down to 0F and there are some that probably go colder. I suspect 
> efficiency takes a dump at those temps though.
> 
> The guy I'm training to run the groomer is an HVAC installer and the other 
> night he was telling me that just about nobody is installing ground source 
> heat pumps any more due to the huge cost and the availability of low temp air 
> source units combined with the low cost of natural gas.
> 
> I'd considered ground source but the ones I've looked at are $20,000+ while a 
> new boiler for our house is more like $6,000 and would decrease our oil use 
> 20-25%. It would take a long long time to pay off that extra cost. There are 
> incentives but they're decreasing every year.
> 
> -Curt
> 
> On Tuesday, February 16, 2021, 10:46:10 AM EST, Kaleb Striplin via Mercedes 
>  wrote:
> 
> 
> I don’t know if size matters but it’s a 5 ton unit and even when it was in 
> the single digest I could tell it was putting out heat. I could tell the 
> difference between when the outside unit was running and when it was shut 
> down and only using the aux heat.
> 
> Sent from my iPhone
> 
> > On Feb 16, 2021, at 9:44 AM, Floyd Thursby via Mercedes 
> >  wrote:
> > 
> > There's no point in it running if it can't extract any heat from the air.  
> > It's a wonder it was running and putting out much when it got down below 
> > 20F or so.
> > 
> > --FT
> > 
> >> On 2/16/21 10:36 AM, Kaleb Striplin via Mercedes wrote:
> >> Power just came back on a few minutes ago.  Outside unit still not 
> >> running.  I did find the installation manual online though. Here is some 
> >> info about the defrost and lockouts.  Sounds like it may simply be locking 
> >> out because the temp is too low.
> >> 
> >> Heating Mode:The compressor and fan motor will stop when the low pressure 
> >> control opens and will start again when the low side pressure rises to 
> >> approximately 40 psig when the low pressure automatically resets�If the 
> >> low pressure switch trips 3 times within 120 minutes of operation during a 
> >> particular call for heating operation, the defrost control will lock out 
> >> compressor and outdoor fan operation�If the lock out due to low pressure 
> >> occurs at an outdoor ambient temperature below 5°F, the defrost control 
> >> will automatically exit the lockout mode when the outdoor ambient 
> >> temperature rises 5°F�This feature is necessary since the low pressure 
> >> control could possibly have opened due to the outdoor ambient being very 
> >> low rather than an actual system fault�
> >> 
> >> 
> >> Of course with the power being out I figure that would have caused the 
> >> lockout to reset at least for a while.  Will see what happens when it gets 
> >> over 5 this afternoon.
> > 
> > ___
> > http://www.okiebenz.com
> > 
> > To search list archives http://www.okiebenz.com/archive/
> > 
> > To Unsubscribe or change delivery options go to:
> > http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com
> 
> > 
> 
> 
> ___
> http://www.okiebenz.com
> 
> To search list archives http://www.okiebenz.com/archive/
> 
> To Unsubscribe or change delivery options go to:
> http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com
> 
___
http://www.okiebenz.com

To search list archives http://www.okiebenz.com/archive/

To Unsubscribe or change delivery options go to:
http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com

  
___
http://www.okiebenz.com

To s

Re: [MBZ] Heat pump question

[Kaleb Striplin via Mercedes]

So got questions about these inserts. I have ran it before with the blower 
going and the doors closed and it will heat the house nicely. With no power 
should I run it with the doors open or closed? It’s burning pretty good now but 
seems like there is very little head coming off of it yet. 

Sent from my iPhone

> On Feb 16, 2021, at 10:36 AM, Kaleb Striplin  wrote:
> 
> Got the fire going. Of course it will take a while to start putting off some 
> heat. Without the doors closed and the blower going, it seems like it’s 
> probably operating like a regular fireplace with most of the heat going ok 
> the chimney. 
> 
> Sent from my iPhone
> 
>>> On Feb 16, 2021, at 10:07 AM, Curt Raymond  wrote:
>>> 
>> 
>> Some of those units do pretty amazing things in the cold these days. 10-15 
>> years ago 20F was the practical minimum but I've read of units that will 
>> still work down to 0F and there are some that probably go colder. I suspect 
>> efficiency takes a dump at those temps though.
>> 
>> The guy I'm training to run the groomer is an HVAC installer and the other 
>> night he was telling me that just about nobody is installing ground source 
>> heat pumps any more due to the huge cost and the availability of low temp 
>> air source units combined with the low cost of natural gas.
>> 
>> I'd considered ground source but the ones I've looked at are $20,000+ while 
>> a new boiler for our house is more like $6,000 and would decrease our oil 
>> use 20-25%. It would take a long long time to pay off that extra cost. There 
>> are incentives but they're decreasing every year.
>> 
>> -Curt
>> 
>> On Tuesday, February 16, 2021, 10:46:10 AM EST, Kaleb Striplin via Mercedes 
>>  wrote:
>> 
>> 
>> I don’t know if size matters but it’s a 5 ton unit and even when it was in 
>> the single digest I could tell it was putting out heat. I could tell the 
>> difference between when the outside unit was running and when it was shut 
>> down and only using the aux heat. 
>> 
>> Sent from my iPhone
>> 
>> > On Feb 16, 2021, at 9:44 AM, Floyd Thursby via Mercedes 
>> >  wrote:
>> > 
>> > There's no point in it running if it can't extract any heat from the air. 
>> >  It's a wonder it was running and putting out much when it got down below 
>> > 20F or so.
>> > 
>> > --FT
>> > 
>> >> On 2/16/21 10:36 AM, Kaleb Striplin via Mercedes wrote:
>> >> Power just came back on a few minutes ago.  Outside unit still not 
>> >> running.  I did find the installation manual online though. Here is some 
>> >> info about the defrost and lockouts.  Sounds like it may simply be 
>> >> locking out because the temp is too low.
>> >> 
>> >> Heating Mode:The compressor and fan motor will stop when the low pressure 
>> >> control opens and will start again when the low side pressure rises to 
>> >> approximately 40 psig when the low pressure automatically resets�If the 
>> >> low pressure switch trips 3 times within 120 minutes of operation during 
>> >> a particular call for heating operation, the defrost control will lock 
>> >> out compressor and outdoor fan operation�If the lock out due to low 
>> >> pressure occurs at an outdoor ambient temperature below 5°F, the defrost 
>> >> control will automatically exit the lockout mode when the outdoor ambient 
>> >> temperature rises 5°F�This feature is necessary since the low pressure 
>> >> control could possibly have opened due to the outdoor ambient being very 
>> >> low rather than an actual system fault�
>> >> 
>> >> 
>> >> Of course with the power being out I figure that would have caused the 
>> >> lockout to reset at least for a while.  Will see what happens when it 
>> >> gets over 5 this afternoon.
>> > 
>> > ___
>> > http://www.okiebenz.com
>> > 
>> > To search list archives http://www.okiebenz.com/archive/
>> > 
>> > To Unsubscribe or change delivery options go to:
>> > http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com
>> 
>> > 
>> 
>> 
>> ___
>> http://www.okiebenz.com
>> 
>> To search list archives http://www.okiebenz.com/archive/
>> 
>> To Unsubscribe or change delivery options go to:
>> http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com
>> 
___
http://www.okiebenz.com

To search list archives http://www.okiebenz.com/archive/

To Unsubscribe or change delivery options go to:
http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com

Re: [MBZ] Heat pump question

[Kaleb Striplin via Mercedes]

Got the fire going. Of course it will take a while to start putting off some 
heat. Without the doors closed and the blower going, it seems like it’s 
probably operating like a regular fireplace with most of the heat going ok the 
chimney. 

Sent from my iPhone

> On Feb 16, 2021, at 10:07 AM, Curt Raymond  wrote:
> 
> 
> Some of those units do pretty amazing things in the cold these days. 10-15 
> years ago 20F was the practical minimum but I've read of units that will 
> still work down to 0F and there are some that probably go colder. I suspect 
> efficiency takes a dump at those temps though.
> 
> The guy I'm training to run the groomer is an HVAC installer and the other 
> night he was telling me that just about nobody is installing ground source 
> heat pumps any more due to the huge cost and the availability of low temp air 
> source units combined with the low cost of natural gas.
> 
> I'd considered ground source but the ones I've looked at are $20,000+ while a 
> new boiler for our house is more like $6,000 and would decrease our oil use 
> 20-25%. It would take a long long time to pay off that extra cost. There are 
> incentives but they're decreasing every year.
> 
> -Curt
> 
> On Tuesday, February 16, 2021, 10:46:10 AM EST, Kaleb Striplin via Mercedes 
>  wrote:
> 
> 
> I don’t know if size matters but it’s a 5 ton unit and even when it was in 
> the single digest I could tell it was putting out heat. I could tell the 
> difference between when the outside unit was running and when it was shut 
> down and only using the aux heat.
> 
> Sent from my iPhone
> 
> > On Feb 16, 2021, at 9:44 AM, Floyd Thursby via Mercedes 
> >  wrote:
> > 
> > There's no point in it running if it can't extract any heat from the air.  
> > It's a wonder it was running and putting out much when it got down below 
> > 20F or so.
> > 
> > --FT
> > 
> >> On 2/16/21 10:36 AM, Kaleb Striplin via Mercedes wrote:
> >> Power just came back on a few minutes ago.  Outside unit still not 
> >> running.  I did find the installation manual online though. Here is some 
> >> info about the defrost and lockouts.  Sounds like it may simply be locking 
> >> out because the temp is too low.
> >> 
> >> Heating Mode:The compressor and fan motor will stop when the low pressure 
> >> control opens and will start again when the low side pressure rises to 
> >> approximately 40 psig when the low pressure automatically resets�If the 
> >> low pressure switch trips 3 times within 120 minutes of operation during a 
> >> particular call for heating operation, the defrost control will lock out 
> >> compressor and outdoor fan operation�If the lock out due to low pressure 
> >> occurs at an outdoor ambient temperature below 5°F, the defrost control 
> >> will automatically exit the lockout mode when the outdoor ambient 
> >> temperature rises 5°F�This feature is necessary since the low pressure 
> >> control could possibly have opened due to the outdoor ambient being very 
> >> low rather than an actual system fault�
> >> 
> >> 
> >> Of course with the power being out I figure that would have caused the 
> >> lockout to reset at least for a while.  Will see what happens when it gets 
> >> over 5 this afternoon.
> > 
> > ___
> > http://www.okiebenz.com
> > 
> > To search list archives http://www.okiebenz.com/archive/
> > 
> > To Unsubscribe or change delivery options go to:
> > http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com
> 
> > 
> 
> 
> ___
> http://www.okiebenz.com
> 
> To search list archives http://www.okiebenz.com/archive/
> 
> To Unsubscribe or change delivery options go to:
> http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com
> 
___
http://www.okiebenz.com

To search list archives http://www.okiebenz.com/archive/

To Unsubscribe or change delivery options go to:
http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com

Re: [MBZ] Heat pump question

[Curt Raymond via Mercedes]

 Some of those units do pretty amazing things in the cold these days. 10-15 
years ago 20F was the practical minimum but I've read of units that will still 
work down to 0F and there are some that probably go colder. I suspect 
efficiency takes a dump at those temps though.
The guy I'm training to run the groomer is an HVAC installer and the other 
night he was telling me that just about nobody is installing ground source heat 
pumps any more due to the huge cost and the availability of low temp air source 
units combined with the low cost of natural gas.
I'd considered ground source but the ones I've looked at are $20,000+ while a 
new boiler for our house is more like $6,000 and would decrease our oil use 
20-25%. It would take a long long time to pay off that extra cost. There are 
incentives but they're decreasing every year.
-Curt

On Tuesday, February 16, 2021, 10:46:10 AM EST, Kaleb Striplin via Mercedes 
 wrote:  
 
 I don’t know if size matters but it’s a 5 ton unit and even when it was in the 
single digest I could tell it was putting out heat. I could tell the difference 
between when the outside unit was running and when it was shut down and only 
using the aux heat. 

Sent from my iPhone

> On Feb 16, 2021, at 9:44 AM, Floyd Thursby via Mercedes 
>  wrote:
> 
> There's no point in it running if it can't extract any heat from the air.  
> It's a wonder it was running and putting out much when it got down below 20F 
> or so.
> 
> --FT
> 
>> On 2/16/21 10:36 AM, Kaleb Striplin via Mercedes wrote:
>> Power just came back on a few minutes ago.  Outside unit still not running.  
>> I did find the installation manual online though. Here is some info about 
>> the defrost and lockouts.  Sounds like it may simply be locking out because 
>> the temp is too low.
>> 
>> Heating Mode:The compressor and fan motor will stop when the low pressure 
>> control opens and will start again when the low side pressure rises to 
>> approximately 40 psig when the low pressure automatically resets�If the low 
>> pressure switch trips 3 times within 120 minutes of operation during a 
>> particular call for heating operation, the defrost control will lock out 
>> compressor and outdoor fan operation�If the lock out due to low pressure 
>> occurs at an outdoor ambient temperature below 5°F, the defrost control will 
>> automatically exit the lockout mode when the outdoor ambient temperature 
>> rises 5°F�This feature is necessary since the low pressure control could 
>> possibly have opened due to the outdoor ambient being very low rather than 
>> an actual system fault�
>> 
>> 
>> Of course with the power being out I figure that would have caused the 
>> lockout to reset at least for a while.  Will see what happens when it gets 
>> over 5 this afternoon.
> 
> ___
> http://www.okiebenz.com
> 
> To search list archives http://www.okiebenz.com/archive/
> 
> To Unsubscribe or change delivery options go to:
> http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com
> 


___
http://www.okiebenz.com

To search list archives http://www.okiebenz.com/archive/

To Unsubscribe or change delivery options go to:
http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com

  
___
http://www.okiebenz.com

To search list archives http://www.okiebenz.com/archive/

To Unsubscribe or change delivery options go to:
http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com

Re: [MBZ] Heat pump question

[Kaleb Striplin via Mercedes]

I don’t know if size matters but it’s a 5 ton unit and even when it was in the 
single digest I could tell it was putting out heat. I could tell the difference 
between when the outside unit was running and when it was shut down and only 
using the aux heat. 

Sent from my iPhone

> On Feb 16, 2021, at 9:44 AM, Floyd Thursby via Mercedes 
>  wrote:
> 
> There's no point in it running if it can't extract any heat from the air.  
> It's a wonder it was running and putting out much when it got down below 20F 
> or so.
> 
> --FT
> 
>> On 2/16/21 10:36 AM, Kaleb Striplin via Mercedes wrote:
>> Power just came back on a few minutes ago.  Outside unit still not running.  
>> I did find the installation manual online though. Here is some info about 
>> the defrost and lockouts.  Sounds like it may simply be locking out because 
>> the temp is too low.
>> 
>> Heating Mode:The compressor and fan motor will stop when the low pressure 
>> control opens and will start again when the low side pressure rises to 
>> approximately 40 psig when the low pressure automatically resets�If the low 
>> pressure switch trips 3 times within 120 minutes of operation during a 
>> particular call for heating operation, the defrost control will lock out 
>> compressor and outdoor fan operation�If the lock out due to low pressure 
>> occurs at an outdoor ambient temperature below 5°F, the defrost control will 
>> automatically exit the lockout mode when the outdoor ambient temperature 
>> rises 5°F�This feature is necessary since the low pressure control could 
>> possibly have opened due to the outdoor ambient being very low rather than 
>> an actual system fault�
>> 
>> 
>> Of course with the power being out I figure that would have caused the 
>> lockout to reset at least for a while.  Will see what happens when it gets 
>> over 5 this afternoon.
> 
> ___
> http://www.okiebenz.com
> 
> To search list archives http://www.okiebenz.com/archive/
> 
> To Unsubscribe or change delivery options go to:
> http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com
> 


___
http://www.okiebenz.com

To search list archives http://www.okiebenz.com/archive/

To Unsubscribe or change delivery options go to:
http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com

Re: [MBZ] Heat pump question

[Kaleb Striplin via Mercedes]

Power just went out again. Going to head out and haul in some firewood and see 
if I can get this fireplace going. It’s actually an insert with a blower but I 
guess it will still out out some heat without the blower. 

Sent from my iPhone

> On Feb 16, 2021, at 9:37 AM, Kaleb Striplin  wrote:
> 
> 
> Power just came back on a few minutes ago.  Outside unit still not running.  
> I did find the installation manual online though.  Here is some info about 
> the defrost and lockouts.  Sounds like it may simply be locking out because 
> the temp is too low.
> 
> Heating Mode: The compressor and fan motor will stop when the low pressure 
> control opens and will start again when the low side pressure rises to 
> approximately 40 psig when the low pressure automatically resets� If the low 
> pressure switch trips 3 times within 120 minutes of operation during a 
> particular call for heating operation, the defrost control will lock out 
> compressor and outdoor fan operation� If the lock out due to low pressure 
> occurs at an outdoor ambient temperature below 5°F, the defrost control will 
> automatically exit the lockout mode when the outdoor ambient temperature 
> rises 5°F� This feature is necessary since the low pressure control could 
> possibly have opened due to the outdoor ambient being very low rather than an 
> actual system fault�
> 
> 
> 
> Of course with the power being out I figure that would have caused the 
> lockout to reset at least for a while.  Will see what happens when it gets 
> over 5 this afternoon.
> 
> On 2/16/2021 9:19 AM, Curt Raymond wrote:
>> Wrong attitude, it takes time for the stove to get warm, it takes time to 
>> warm up the house. The time to start the fire is immediately after the power 
>> goes out. If it comes back on quickly then fine, let the fire go out. If you 
>> wait until you're cold you're going to be very cold before the fire gets 
>> things warmed back up.
>> 
>> -Curt
>> 
>> On Tuesday, February 16, 2021, 9:23:26 AM EST, Kaleb Striplin via Mercedes 
>>  wrote:
>> 
>> 
>> Good idea, I will see if I can find one. At the current moment it is 
>> irrelevant anyway as the power has been off for an hour. Supposedly will be 
>> restored by 9am. If it comes back in then, fine. If it goes past that I will 
>> have to fire up the fireplace. 
>> 
>> Sent from my iPhone
>> 
>> > On Feb 15, 2021, at 11:06 PM, Scott Ritchey via Mercedes 
>> >  wrote:
>> > 
>> > When all else fails, read the instructions?  The basic setup is the same 
>> > for most heat pump systems except for details like TXV vs piston/orifice.  
>> > But the control electronics (typically on a defrost control board) can do 
>> > anything, like totally shut down below some temp.  Might be worth 
>> > downloading and browsing the owners' manual (or might not; some are much 
>> > worse than others).
>> > 
>> > -Original Message-
>> > From: Mercedes On Behalf Of Kaleb Striplin via Mercedes
>> > Sent: Monday, February 15, 2021 11:52 PM
>> > To: Kaleb Striplin via Mercedes 
>> > Cc: Kaleb Striplin 
>> > Subject: Re: [MBZ] Heat pump question
>> > 
>> > Sounds like the unit just kicked back on. Guess we shall see how the night 
>> > goes. 
>> > 
>> > Sent from my iPhone
>> > 
>> >> On Feb 15, 2021, at 10:44 PM, Kaleb Striplin via Mercedes 
>> >>  wrote:
>> >> 
>> >> I will be damned if it isn’t shut off again. Can say for sure about last 
>> >> time but this time code is for low pressure switch open, not the same low 
>> >> pressure lockout as before. Don’t see any loose or damaged wires to any 
>> >> pressure switches. Jumping the pins didn’t reset it either. Guess it will 
>> >> be expensive aux heat tonight. 
>> >> 
>> >> Sent from my iPhone
>> >> 
>> >>>> On Feb 15, 2021, at 10:23 PM, Kaleb Striplin  wrote:
>> >>> 
>> >>> Just noticed outside unit was shut off again. Coils had no frost on 
>> >>> them at all but it was in low pressure lockout. Reset it and forced a 
>> >>> defrost away way. It’s down to -4 at the moment. I wonder if it’s just 
>> >>> too damn cold for it and pressure is dropping, or if it really is low on 
>> >>> charge. If so, can these things even be charged in the winter? Or do 
>> >>> they have to be done during the warmer months? Btw supposed to get down 
>> >>> to -14 tonight. 
>> >>> 
>

Re: [MBZ] Heat pump question

[Floyd Thursby via Mercedes]

There's no point in it running if it can't extract any heat from the 
air.  It's a wonder it was running and putting out much when it got down 
below 20F or so.


--FT

On 2/16/21 10:36 AM, Kaleb Striplin via Mercedes wrote:
Power just came back on a few minutes ago.  Outside unit still not 
running.  I did find the installation manual online though. Here is 
some info about the defrost and lockouts.  Sounds like it may simply 
be locking out because the temp is too low.


Heating Mode:The compressor and fan motor will stop when the low 
pressure control opens and will start again when the low side pressure 
rises to approximately 40 psig when the low pressure automatically 
resets�If the low pressure switch trips 3 times within 120 minutes of 
operation during a particular call for heating operation, the defrost 
control will lock out compressor and outdoor fan operation�If the lock 
out due to low pressure occurs at an outdoor ambient temperature below 
5°F, the defrost control will automatically exit the lockout mode when 
the outdoor ambient temperature rises 5°F�This feature is necessary 
since the low pressure control could possibly have opened due to the 
outdoor ambient being very low rather than an actual system fault�



Of course with the power being out I figure that would have caused the 
lockout to reset at least for a while.  Will see what happens when it 
gets over 5 this afternoon.


___
http://www.okiebenz.com

To search list archives http://www.okiebenz.com/archive/

To Unsubscribe or change delivery options go to:
http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com

Re: [MBZ] Heat pump question

[Kaleb Striplin via Mercedes]

Power just came back on a few minutes ago.  Outside unit still not 
running.  I did find the installation manual online though. Here is some 
info about the defrost and lockouts.  Sounds like it may simply be 
locking out because the temp is too low.


Heating Mode:The compressor and fan motor will stop when the low 
pressure control opens and will start again when the low side pressure 
rises to approximately 40 psig when the low pressure automatically 
resets�If the low pressure switch trips 3 times within 120 minutes of 
operation during a particular call for heating operation, the defrost 
control will lock out compressor and outdoor fan operation�If the lock 
out due to low pressure occurs at an outdoor ambient temperature below 
5°F, the defrost control will automatically exit the lockout mode when 
the outdoor ambient temperature rises 5°F�This feature is necessary 
since the low pressure control could possibly have opened due to the 
outdoor ambient being very low rather than an actual system fault�



Of course with the power being out I figure that would have caused the 
lockout to reset at least for a while.  Will see what happens when it 
gets over 5 this afternoon.


On 2/16/2021 9:19 AM, Curt Raymond wrote:
Wrong attitude, it takes time for the stove to get warm, it takes time 
to warm up the house. The time to start the fire is immediately after 
the power goes out. If it comes back on quickly then fine, let the 
fire go out. If you wait until you're cold you're going to be very 
cold before the fire gets things warmed back up.


-Curt

On Tuesday, February 16, 2021, 9:23:26 AM EST, Kaleb Striplin via 
Mercedes  wrote:



Good idea, I will see if I can find one. At the current moment it is 
irrelevant anyway as the power has been off for an hour. Supposedly 
will be restored by 9am. If it comes back in then, fine. If it goes 
past that I will have to fire up the fireplace.


Sent from my iPhone

> On Feb 15, 2021, at 11:06 PM, Scott Ritchey via Mercedes 
mailto:mercedes@okiebenz.com>> wrote:

>
> When all else fails, read the instructions?  The basic setup is the 
same for most heat pump systems except for details like TXV vs 
piston/orifice.  But the control electronics (typically on a defrost 
control board) can do anything, like totally shut down below some 
temp.  Might be worth downloading and browsing the owners' manual (or 
might not; some are much worse than others).

>
> -Original Message-
> From: Mercedes On Behalf Of Kaleb Striplin via Mercedes
> Sent: Monday, February 15, 2021 11:52 PM
> To: Kaleb Striplin via Mercedes <mailto:mercedes@okiebenz.com>>

> Cc: Kaleb Striplin mailto:ka...@striplin.net>>
> Subject: Re: [MBZ] Heat pump question
>
> Sounds like the unit just kicked back on. Guess we shall see how the 
night goes.

>
> Sent from my iPhone
>
>> On Feb 15, 2021, at 10:44 PM, Kaleb Striplin via Mercedes 
mailto:mercedes@okiebenz.com>> wrote:

>>
>> I will be damned if it isn’t shut off again. Can say for sure 
about last time but this time code is for low pressure switch open, 
not the same low pressure lockout as before. Don’t see any loose or 
damaged wires to any pressure switches. Jumping the pins didn’t reset 
it either. Guess it will be expensive aux heat tonight.

>>
>> Sent from my iPhone
>>
>>>> On Feb 15, 2021, at 10:23 PM, Kaleb Striplin <mailto:ka...@striplin.net>> wrote:

>>>
>>> Just noticed outside unit was shut off again. Coils had no frost 
on them at all but it was in low pressure lockout. Reset it and forced 
a defrost away way. It’s down to -4 at the moment. I wonder if it’s 
just too damn cold for it and pressure is dropping, or if it really is 
low on charge. If so, can these things even be charged in the winter? 
Or do they have to be done during the warmer months? Btw supposed to 
get down to -14 tonight.

>>>
>>> Sent from my iPhone
>>>
>>>>> On Feb 15, 2021, at 5:23 PM, Kaleb Striplin <mailto:ka...@striplin.net>> wrote:

>>>>
>>>> Checked it a little while ago and the coils are clear.
>>>>
>>>>>> On 2/15/2021 3:22 PM, Kaleb Striplin wrote:
>>>>> It’s been running all day without issue. I can’t say I have 
noticed if it’s ran a defrost cycle or not. I think here shortly I 
will go out and look at the coils and see if they are clear or have 
started frosting up again.

>>>>>
>>>>> Sent from my iPhone
>>>>>
>>>>>>> On Feb 15, 2021, at 2:17 PM, Scott Ritchey via Mercedes 
mailto:mercedes@okiebenz.com>> wrote:

>>>>>>
>>>>>> Probably, given the outside temps and state of charge, the gas 
pressure going into the compressor gets too low if ice prevents the 

Re: [MBZ] Heat pump question

[Curt Raymond via Mercedes]

 Wrong attitude, it takes time for the stove to get warm, it takes time to warm 
up the house. The time to start the fire is immediately after the power goes 
out. If it comes back on quickly then fine, let the fire go out. If you wait 
until you're cold you're going to be very cold before the fire gets things 
warmed back up.
-Curt

On Tuesday, February 16, 2021, 9:23:26 AM EST, Kaleb Striplin via Mercedes 
 wrote:  
 
 Good idea, I will see if I can find one. At the current moment it is 
irrelevant anyway as the power has been off for an hour. Supposedly will be 
restored by 9am. If it comes back in then, fine. If it goes past that I will 
have to fire up the fireplace. 

Sent from my iPhone

> On Feb 15, 2021, at 11:06 PM, Scott Ritchey via Mercedes 
>  wrote:
> 
> When all else fails, read the instructions?  The basic setup is the same for 
> most heat pump systems except for details like TXV vs piston/orifice.  But 
> the control electronics (typically on a defrost control board) can do 
> anything, like totally shut down below some temp.  Might be worth downloading 
> and browsing the owners' manual (or might not; some are much worse than 
> others).
> 
> -Original Message-
> From: Mercedes On Behalf Of Kaleb Striplin via Mercedes
> Sent: Monday, February 15, 2021 11:52 PM
> To: Kaleb Striplin via Mercedes 
> Cc: Kaleb Striplin 
> Subject: Re: [MBZ] Heat pump question
> 
> Sounds like the unit just kicked back on. Guess we shall see how the night 
> goes. 
> 
> Sent from my iPhone
> 
>> On Feb 15, 2021, at 10:44 PM, Kaleb Striplin via Mercedes 
>>  wrote:
>> 
>> I will be damned if it isn’t shut off again. Can say for sure about last 
>> time but this time code is for low pressure switch open, not the same low 
>> pressure lockout as before. Don’t see any loose or damaged wires to any 
>> pressure switches. Jumping the pins didn’t reset it either. Guess it will be 
>> expensive aux heat tonight. 
>> 
>> Sent from my iPhone
>> 
>>>> On Feb 15, 2021, at 10:23 PM, Kaleb Striplin  wrote:
>>> 
>>> Just noticed outside unit was shut off again. Coils had no frost on them 
>>> at all but it was in low pressure lockout. Reset it and forced a defrost 
>>> away way. It’s down to -4 at the moment. I wonder if it’s just too damn 
>>> cold for it and pressure is dropping, or if it really is low on charge. If 
>>> so, can these things even be charged in the winter? Or do they have to be 
>>> done during the warmer months? Btw supposed to get down to -14 tonight. 
>>> 
>>> Sent from my iPhone
>>> 
>>>>> On Feb 15, 2021, at 5:23 PM, Kaleb Striplin  wrote:
>>>> 
>>>> Checked it a little while ago and the coils are clear.
>>>> 
>>>>>> On 2/15/2021 3:22 PM, Kaleb Striplin wrote:
>>>>> It’s been running all day without issue. I can’t say I have noticed if 
>>>>> it’s ran a defrost cycle or not. I think here shortly I will go out and 
>>>>> look at the coils and see if they are clear or have started frosting up 
>>>>> again.
>>>>> 
>>>>> Sent from my iPhone
>>>>> 
>>>>>>> On Feb 15, 2021, at 2:17 PM, Scott Ritchey via Mercedes 
>>>>>>>  wrote:
>>>>>> 
>>>>>> Probably, given the outside temps and state of charge, the gas pressure 
>>>>>> going into the compressor gets too low if ice prevents the coils from 
>>>>>> absorbing enough heat to raise the pressure (from that very cold air).
>>>>>> 
>>>>>> -Original Message-
>>>>>> From: Mercedes On Behalf Of Kaleb Striplin via Mercedes
>>>>>> Sent: Monday, February 15, 2021 10:31 AM
>>>>>> To: mercedes@okiebenz.com
>>>>>> Cc: Kaleb Striplin 
>>>>>> Subject: Re: [MBZ] Heat pump question
>>>>>> 
>>>>>> Well I went out and checked it.  When I looked at in there was no frost 
>>>>>> on the coils that I could see in the center part.  I pulled the cover 
>>>>>> and sure enough it was blinking a low pressure lockout. With the side 
>>>>>> cover off I could see some frost on the outside of the coils, not a 
>>>>>> whole lot though.  I shorted the test pins to reset it and it kicked 
>>>>>> back on.  I shorted them again to force a defrost.  Defrost ran for 
>>>>>> about 5-10 minutes and once frost was clear it kicked back into heat 
>>>>>> mode.
>&

Re: [MBZ] Heat pump question

[Floyd Thursby via Mercedes]

haha I knew that would get a rise.

It was close to 70F here last night when the tstorms rolled through, 
this morning maybe high 50s so far and sunny for the first time in like 
10 days. And of course the dogs have no interest in going outside, the 
last few days in the rain they couldn't wait to go out and were like 
toddlers cooped up inside.  This morning they just want to be layabouts.


--FT

On 2/16/21 9:42 AM, Kaleb Striplin via Mercedes wrote:

You are an asshole.

Sent from my iPhone


On Feb 16, 2021, at 8:36 AM, Dan Penoff via Mercedes  
wrote:

I have the sliding doors open to the lanai and it’s about 70 in the house. No 
fires. Plenty of electricity.

-D


On Feb 16, 2021, at 9:27 AM, Kaleb Striplin via Mercedes 
 wrote:

Well the blackout appears to have rolled our way. It went out around 7 and the 
text notification from PSO says estimated to be back on at 9.

It’s -9 out right now and down to 63 in the house (I normally keep it at 68.

Sent from my iPhone


On Feb 15, 2021, at 11:38 PM, OK Don via Mercedes  wrote:

As Allen said, when there's no heat in the air, it can't pump any, and is
probably smart enough not to try. If the aux heat strips are working, then
it's doing what it's supposed to do. Leave it alone and get some sleep (if
the power stays on).
OG&E is threatening rolling two hour blackouts if demand doesn't go down.
With the temp dropping below -12°F tonight, I don't see that happening.


On Mon, Feb 15, 2021 at 10:44 PM Allan Streib via Mercedes <
mercedes@okiebenz.com> wrote:

I think you're below the temps where a ambient-air heat pump really does
anything at all. But as I said earlier I'm not speaking from experience.

I'd fire up the wood stove if it were me.

Allan


Kaleb Striplin via Mercedes  writes:


Just noticed outside unit was shut off again. Coils had no frost on them

at all but it was in low pressure lockout. Reset it and forced a defrost
away way. It’s down to -4 at the moment. I wonder if it’s just too damn
cold for it and pressure is dropping, or if it really is low on charge. If
so, can these things even be charged in the winter? Or do they have to be
done during the warmer months? Btw supposed to get down to -14 tonight.

Sent from my iPhone


On Feb 15, 2021, at 5:23 PM, Kaleb Striplin  wrote:

Checked it a little while ago and the coils are clear.


On 2/15/2021 3:22 PM, Kaleb Striplin wrote:
It’s been running all day without issue. I can’t say I have noticed if

it’s ran a defrost cycle or not. I think here shortly I will go out and
look at the coils and see if they are clear or have started frosting up
again.

Sent from my iPhone


On Feb 15, 2021, at 2:17 PM, Scott Ritchey via Mercedes <

mercedes@okiebenz.com> wrote:

Probably, given the outside temps and state of charge, the gas

pressure going into the compressor gets too low if ice prevents the coils
from absorbing enough heat to raise the pressure (from that very cold air).

-Original Message-
From: Mercedes On Behalf Of Kaleb Striplin via Mercedes
Sent: Monday, February 15, 2021 10:31 AM
To: mercedes@okiebenz.com
Cc: Kaleb Striplin 
Subject: Re: [MBZ] Heat pump question

Well I went out and checked it.  When I looked at in there was no

frost on the coils that I could see in the center part.  I pulled the cover
and sure enough it was blinking a low pressure lockout. With the side cover
off I could see some frost on the outside of the coils, not a whole lot
though.  I shorted the test pins to reset it and it kicked back on.  I
shorted them again to force a defrost.  Defrost ran for about 5-10 minutes
and once frost was clear it kicked back into heat mode.

Since replacing the defrost board with attached sensor last year, I

have not had a problem sense.  Why the heck did it happen again?  I know it
has a temp sensor for the coils.  Do these work by going into a defrost
cycle on a timed basis if the temp sensor is below a certain temp?  Or do
they sense the coils are freezing up and enter defrost when needed (not on
a timed scheduled).

 From what I recall, some old systems did not have a temp sensor and

just went into defrost every so often.  I think some systems sense when it
needs to be done.  Others I think are still timed but only do it when temp
is below a certain point.  This is a 2008 Rheem running on 410 so I am not
sure.  If mine runs on a timer only when temp gets low maybe it is so cold
that it simply did not reach its run time to defrost soon enough before it
started frosting up, or perhaps it is sucking in blowing snow which caused
it to frost up faster?

On 2/15/2021 9:03 AM, Kaleb Striplin via Mercedes wrote:
It is now -3 outside, not sure how low it got last night. Anyway,

heat

pump has been running pretty much non stop for the last few days with
the aux heat kicking on occasionally. Yesterday afternoon aux heat

was

on quite a bit as it never got over 4 yesterday.  This morning when I
woke up out

Re: [MBZ] Heat pump question

[Kaleb Striplin via Mercedes]

You are an asshole. 

Sent from my iPhone

> On Feb 16, 2021, at 8:36 AM, Dan Penoff via Mercedes  
> wrote:
> 
> I have the sliding doors open to the lanai and it’s about 70 in the house. 
> No fires. Plenty of electricity.
> 
> -D
> 
>> On Feb 16, 2021, at 9:27 AM, Kaleb Striplin via Mercedes 
>>  wrote:
>> 
>> Well the blackout appears to have rolled our way. It went out around 7 and 
>> the text notification from PSO says estimated to be back on at 9. 
>> 
>> It’s -9 out right now and down to 63 in the house (I normally keep it at 68. 
>> 
>> Sent from my iPhone
>> 
>>>> On Feb 15, 2021, at 11:38 PM, OK Don via Mercedes  
>>>> wrote:
>>> 
>>> As Allen said, when there's no heat in the air, it can't pump any, and is
>>> probably smart enough not to try. If the aux heat strips are working, then
>>> it's doing what it's supposed to do. Leave it alone and get some sleep (if
>>> the power stays on).
>>> OG&E is threatening rolling two hour blackouts if demand doesn't go down.
>>> With the temp dropping below -12°F tonight, I don't see that happening.
>>> 
>>>> On Mon, Feb 15, 2021 at 10:44 PM Allan Streib via Mercedes <
>>>> mercedes@okiebenz.com> wrote:
>>>> 
>>>> I think you're below the temps where a ambient-air heat pump really does
>>>> anything at all. But as I said earlier I'm not speaking from experience.
>>>> 
>>>> I'd fire up the wood stove if it were me.
>>>> 
>>>> Allan
>>>> 
>>>> 
>>>> Kaleb Striplin via Mercedes  writes:
>>>> 
>>>>> Just noticed outside unit was shut off again. Coils had no frost on them
>>>> at all but it was in low pressure lockout. Reset it and forced a defrost
>>>> away way. It’s down to -4 at the moment. I wonder if it’s just too damn
>>>> cold for it and pressure is dropping, or if it really is low on charge. If
>>>> so, can these things even be charged in the winter? Or do they have to be
>>>> done during the warmer months? Btw supposed to get down to -14 tonight.
>>>>> 
>>>>> Sent from my iPhone
>>>>> 
>>>>>> On Feb 15, 2021, at 5:23 PM, Kaleb Striplin  wrote:
>>>>>> 
>>>>>> Checked it a little while ago and the coils are clear.
>>>>>> 
>>>>>>> On 2/15/2021 3:22 PM, Kaleb Striplin wrote:
>>>>>>> It’s been running all day without issue. I can’t say I have noticed if
>>>> it’s ran a defrost cycle or not. I think here shortly I will go out and
>>>> look at the coils and see if they are clear or have started frosting up
>>>> again.
>>>>>>> 
>>>>>>> Sent from my iPhone
>>>>>>> 
>>>>>>>>> On Feb 15, 2021, at 2:17 PM, Scott Ritchey via Mercedes <
>>>> mercedes@okiebenz.com> wrote:
>>>>>>>> 
>>>>>>>> Probably, given the outside temps and state of charge, the gas
>>>> pressure going into the compressor gets too low if ice prevents the coils
>>>> from absorbing enough heat to raise the pressure (from that very cold air).
>>>>>>>> 
>>>>>>>> -Original Message-
>>>>>>>> From: Mercedes On Behalf Of Kaleb Striplin via Mercedes
>>>>>>>> Sent: Monday, February 15, 2021 10:31 AM
>>>>>>>> To: mercedes@okiebenz.com
>>>>>>>> Cc: Kaleb Striplin 
>>>>>>>> Subject: Re: [MBZ] Heat pump question
>>>>>>>> 
>>>>>>>> Well I went out and checked it.  When I looked at in there was no
>>>> frost on the coils that I could see in the center part.  I pulled the cover
>>>> and sure enough it was blinking a low pressure lockout. With the side cover
>>>> off I could see some frost on the outside of the coils, not a whole lot
>>>> though.  I shorted the test pins to reset it and it kicked back on.  I
>>>> shorted them again to force a defrost.  Defrost ran for about 5-10 minutes
>>>> and once frost was clear it kicked back into heat mode.
>>>>>>>> 
>>>>>>>> Since replacing the defrost board with attached sensor last year, I
>>>> have not had a problem sense.  Why the heck did it happen again?  I know it
>>>> has a 

Re: [MBZ] Heat pump question

[Dan Penoff via Mercedes]

I have the sliding doors open to the lanai and it’s about 70 in the house. No 
fires. Plenty of electricity.

-D

> On Feb 16, 2021, at 9:27 AM, Kaleb Striplin via Mercedes 
>  wrote:
> 
> Well the blackout appears to have rolled our way. It went out around 7 and 
> the text notification from PSO says estimated to be back on at 9. 
> 
> It’s -9 out right now and down to 63 in the house (I normally keep it at 68. 
> 
> Sent from my iPhone
> 
>> On Feb 15, 2021, at 11:38 PM, OK Don via Mercedes  
>> wrote:
>> 
>> As Allen said, when there's no heat in the air, it can't pump any, and is
>> probably smart enough not to try. If the aux heat strips are working, then
>> it's doing what it's supposed to do. Leave it alone and get some sleep (if
>> the power stays on).
>> OG&E is threatening rolling two hour blackouts if demand doesn't go down.
>> With the temp dropping below -12°F tonight, I don't see that happening.
>> 
>>> On Mon, Feb 15, 2021 at 10:44 PM Allan Streib via Mercedes <
>>> mercedes@okiebenz.com> wrote:
>>> 
>>> I think you're below the temps where a ambient-air heat pump really does
>>> anything at all. But as I said earlier I'm not speaking from experience.
>>> 
>>> I'd fire up the wood stove if it were me.
>>> 
>>> Allan
>>> 
>>> 
>>> Kaleb Striplin via Mercedes  writes:
>>> 
>>>> Just noticed outside unit was shut off again. Coils had no frost on them
>>> at all but it was in low pressure lockout. Reset it and forced a defrost
>>> away way. It’s down to -4 at the moment. I wonder if it’s just too damn
>>> cold for it and pressure is dropping, or if it really is low on charge. If
>>> so, can these things even be charged in the winter? Or do they have to be
>>> done during the warmer months? Btw supposed to get down to -14 tonight.
>>>> 
>>>> Sent from my iPhone
>>>> 
>>>>> On Feb 15, 2021, at 5:23 PM, Kaleb Striplin  wrote:
>>>>> 
>>>>> Checked it a little while ago and the coils are clear.
>>>>> 
>>>>>> On 2/15/2021 3:22 PM, Kaleb Striplin wrote:
>>>>>> It’s been running all day without issue. I can’t say I have noticed if
>>> it’s ran a defrost cycle or not. I think here shortly I will go out and
>>> look at the coils and see if they are clear or have started frosting up
>>> again.
>>>>>> 
>>>>>> Sent from my iPhone
>>>>>> 
>>>>>>>> On Feb 15, 2021, at 2:17 PM, Scott Ritchey via Mercedes <
>>> mercedes@okiebenz.com> wrote:
>>>>>>> 
>>>>>>> Probably, given the outside temps and state of charge, the gas
>>> pressure going into the compressor gets too low if ice prevents the coils
>>> from absorbing enough heat to raise the pressure (from that very cold air).
>>>>>>> 
>>>>>>> -Original Message-
>>>>>>> From: Mercedes On Behalf Of Kaleb Striplin via Mercedes
>>>>>>> Sent: Monday, February 15, 2021 10:31 AM
>>>>>>> To: mercedes@okiebenz.com
>>>>>>> Cc: Kaleb Striplin 
>>>>>>> Subject: Re: [MBZ] Heat pump question
>>>>>>> 
>>>>>>> Well I went out and checked it.  When I looked at in there was no
>>> frost on the coils that I could see in the center part.  I pulled the cover
>>> and sure enough it was blinking a low pressure lockout. With the side cover
>>> off I could see some frost on the outside of the coils, not a whole lot
>>> though.  I shorted the test pins to reset it and it kicked back on.  I
>>> shorted them again to force a defrost.  Defrost ran for about 5-10 minutes
>>> and once frost was clear it kicked back into heat mode.
>>>>>>> 
>>>>>>> Since replacing the defrost board with attached sensor last year, I
>>> have not had a problem sense.  Why the heck did it happen again?  I know it
>>> has a temp sensor for the coils.  Do these work by going into a defrost
>>> cycle on a timed basis if the temp sensor is below a certain temp?  Or do
>>> they sense the coils are freezing up and enter defrost when needed (not on
>>> a timed scheduled).
>>>>>>> 
>>>>>>> From what I recall, some old systems did not have a temp sensor and
>>> just went into defrost every so often.  I think some syste

Re: [MBZ] Heat pump question

[Kaleb Striplin via Mercedes]

Well the blackout appears to have rolled our way. It went out around 7 and the 
text notification from PSO says estimated to be back on at 9. 

It’s -9 out right now and down to 63 in the house (I normally keep it at 68. 

Sent from my iPhone

> On Feb 15, 2021, at 11:38 PM, OK Don via Mercedes  
> wrote:
> 
> As Allen said, when there's no heat in the air, it can't pump any, and is
> probably smart enough not to try. If the aux heat strips are working, then
> it's doing what it's supposed to do. Leave it alone and get some sleep (if
> the power stays on).
> OG&E is threatening rolling two hour blackouts if demand doesn't go down.
> With the temp dropping below -12°F tonight, I don't see that happening.
> 
>> On Mon, Feb 15, 2021 at 10:44 PM Allan Streib via Mercedes <
>> mercedes@okiebenz.com> wrote:
>> 
>> I think you're below the temps where a ambient-air heat pump really does
>> anything at all. But as I said earlier I'm not speaking from experience.
>> 
>> I'd fire up the wood stove if it were me.
>> 
>> Allan
>> 
>> 
>> Kaleb Striplin via Mercedes  writes:
>> 
>>> Just noticed outside unit was shut off again. Coils had no frost on them
>> at all but it was in low pressure lockout. Reset it and forced a defrost
>> away way. It’s down to -4 at the moment. I wonder if it’s just too damn
>> cold for it and pressure is dropping, or if it really is low on charge. If
>> so, can these things even be charged in the winter? Or do they have to be
>> done during the warmer months? Btw supposed to get down to -14 tonight.
>>> 
>>> Sent from my iPhone
>>> 
>>>> On Feb 15, 2021, at 5:23 PM, Kaleb Striplin  wrote:
>>>> 
>>>> Checked it a little while ago and the coils are clear.
>>>> 
>>>>> On 2/15/2021 3:22 PM, Kaleb Striplin wrote:
>>>>> It’s been running all day without issue. I can’t say I have noticed if
>> it’s ran a defrost cycle or not. I think here shortly I will go out and
>> look at the coils and see if they are clear or have started frosting up
>> again.
>>>>> 
>>>>> Sent from my iPhone
>>>>> 
>>>>>>> On Feb 15, 2021, at 2:17 PM, Scott Ritchey via Mercedes <
>> mercedes@okiebenz.com> wrote:
>>>>>> 
>>>>>> Probably, given the outside temps and state of charge, the gas
>> pressure going into the compressor gets too low if ice prevents the coils
>> from absorbing enough heat to raise the pressure (from that very cold air).
>>>>>> 
>>>>>> -Original Message-
>>>>>> From: Mercedes On Behalf Of Kaleb Striplin via Mercedes
>>>>>> Sent: Monday, February 15, 2021 10:31 AM
>>>>>> To: mercedes@okiebenz.com
>>>>>> Cc: Kaleb Striplin 
>>>>>> Subject: Re: [MBZ] Heat pump question
>>>>>> 
>>>>>> Well I went out and checked it.  When I looked at in there was no
>> frost on the coils that I could see in the center part.  I pulled the cover
>> and sure enough it was blinking a low pressure lockout. With the side cover
>> off I could see some frost on the outside of the coils, not a whole lot
>> though.  I shorted the test pins to reset it and it kicked back on.  I
>> shorted them again to force a defrost.  Defrost ran for about 5-10 minutes
>> and once frost was clear it kicked back into heat mode.
>>>>>> 
>>>>>> Since replacing the defrost board with attached sensor last year, I
>> have not had a problem sense.  Why the heck did it happen again?  I know it
>> has a temp sensor for the coils.  Do these work by going into a defrost
>> cycle on a timed basis if the temp sensor is below a certain temp?  Or do
>> they sense the coils are freezing up and enter defrost when needed (not on
>> a timed scheduled).
>>>>>> 
>>>>>> From what I recall, some old systems did not have a temp sensor and
>> just went into defrost every so often.  I think some systems sense when it
>> needs to be done.  Others I think are still timed but only do it when temp
>> is below a certain point.  This is a 2008 Rheem running on 410 so I am not
>> sure.  If mine runs on a timer only when temp gets low maybe it is so cold
>> that it simply did not reach its run time to defrost soon enough before it
>> started frosting up, or perhaps it is sucking in blowing snow which caused
>> it to frost up faster?
>>>>>> 
>>>>>>> On 2/15/

Re: [MBZ] Heat pump question

[Kaleb Striplin via Mercedes]

Good idea, I will see if I can find one. At the current moment it is irrelevant 
anyway as the power has been off for an hour. Supposedly will be restored by 
9am. If it comes back in then, fine. If it goes past that I will have to fire 
up the fireplace. 

Sent from my iPhone

> On Feb 15, 2021, at 11:06 PM, Scott Ritchey via Mercedes 
>  wrote:
> 
> When all else fails, read the instructions?  The basic setup is the same for 
> most heat pump systems except for details like TXV vs piston/orifice.  But 
> the control electronics (typically on a defrost control board) can do 
> anything, like totally shut down below some temp.  Might be worth downloading 
> and browsing the owners' manual (or might not; some are much worse than 
> others).
> 
> -Original Message-
> From: Mercedes On Behalf Of Kaleb Striplin via Mercedes
> Sent: Monday, February 15, 2021 11:52 PM
> To: Kaleb Striplin via Mercedes 
> Cc: Kaleb Striplin 
> Subject: Re: [MBZ] Heat pump question
> 
> Sounds like the unit just kicked back on. Guess we shall see how the night 
> goes. 
> 
> Sent from my iPhone
> 
>> On Feb 15, 2021, at 10:44 PM, Kaleb Striplin via Mercedes 
>>  wrote:
>> 
>> I will be damned if it isn’t shut off again. Can say for sure about last 
>> time but this time code is for low pressure switch open, not the same low 
>> pressure lockout as before. Don’t see any loose or damaged wires to any 
>> pressure switches. Jumping the pins didn’t reset it either. Guess it will be 
>> expensive aux heat tonight. 
>> 
>> Sent from my iPhone
>> 
>>>> On Feb 15, 2021, at 10:23 PM, Kaleb Striplin  wrote:
>>> 
>>> Just noticed outside unit was shut off again. Coils had no frost on them 
>>> at all but it was in low pressure lockout. Reset it and forced a defrost 
>>> away way. It’s down to -4 at the moment. I wonder if it’s just too damn 
>>> cold for it and pressure is dropping, or if it really is low on charge. If 
>>> so, can these things even be charged in the winter? Or do they have to be 
>>> done during the warmer months? Btw supposed to get down to -14 tonight. 
>>> 
>>> Sent from my iPhone
>>> 
>>>>> On Feb 15, 2021, at 5:23 PM, Kaleb Striplin  wrote:
>>>> 
>>>> Checked it a little while ago and the coils are clear.
>>>> 
>>>>>> On 2/15/2021 3:22 PM, Kaleb Striplin wrote:
>>>>> It’s been running all day without issue. I can’t say I have noticed if 
>>>>> it’s ran a defrost cycle or not. I think here shortly I will go out and 
>>>>> look at the coils and see if they are clear or have started frosting up 
>>>>> again.
>>>>> 
>>>>> Sent from my iPhone
>>>>> 
>>>>>>> On Feb 15, 2021, at 2:17 PM, Scott Ritchey via Mercedes 
>>>>>>>  wrote:
>>>>>> 
>>>>>> Probably, given the outside temps and state of charge, the gas pressure 
>>>>>> going into the compressor gets too low if ice prevents the coils from 
>>>>>> absorbing enough heat to raise the pressure (from that very cold air).
>>>>>> 
>>>>>> -Original Message-
>>>>>> From: Mercedes On Behalf Of Kaleb Striplin via Mercedes
>>>>>> Sent: Monday, February 15, 2021 10:31 AM
>>>>>> To: mercedes@okiebenz.com
>>>>>> Cc: Kaleb Striplin 
>>>>>> Subject: Re: [MBZ] Heat pump question
>>>>>> 
>>>>>> Well I went out and checked it.  When I looked at in there was no frost 
>>>>>> on the coils that I could see in the center part.  I pulled the cover 
>>>>>> and sure enough it was blinking a low pressure lockout. With the side 
>>>>>> cover off I could see some frost on the outside of the coils, not a 
>>>>>> whole lot though.  I shorted the test pins to reset it and it kicked 
>>>>>> back on.  I shorted them again to force a defrost.  Defrost ran for 
>>>>>> about 5-10 minutes and once frost was clear it kicked back into heat 
>>>>>> mode.
>>>>>> 
>>>>>> Since replacing the defrost board with attached sensor last year, I have 
>>>>>> not had a problem sense.  Why the heck did it happen again?  I know it 
>>>>>> has a temp sensor for the coils.  Do these work by going into a defrost 
>>>>>> cycle on a timed basis if the temp sensor is below a certain temp?  Or 
>>>>>> do

Re: [MBZ] Heat pump question

[Max Dillon via Mercedes]

That's what I'd be doing, light the fire and throw an extra blanket on the bed.

Feb 15, 2021 11:44:21 PM Allan Streib via Mercedes :

> I think you're below the temps where a ambient-air heat pump really does
> anything at all. But as I said earlier I'm not speaking from experience.
>
> I'd fire up the wood stove if it were me.
>
> Allan
>

Max Dillon
Charleston SC


___
http://www.okiebenz.com

To search list archives http://www.okiebenz.com/archive/

To Unsubscribe or change delivery options go to:
http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com

Re: [MBZ] Heat pump question

[OK Don via Mercedes]

As Allen said, when there's no heat in the air, it can't pump any, and is
probably smart enough not to try. If the aux heat strips are working, then
it's doing what it's supposed to do. Leave it alone and get some sleep (if
the power stays on).
OG&E is threatening rolling two hour blackouts if demand doesn't go down.
With the temp dropping below -12°F tonight, I don't see that happening.

On Mon, Feb 15, 2021 at 10:44 PM Allan Streib via Mercedes <
mercedes@okiebenz.com> wrote:

> I think you're below the temps where a ambient-air heat pump really does
> anything at all. But as I said earlier I'm not speaking from experience.
>
> I'd fire up the wood stove if it were me.
>
> Allan
>
>
> Kaleb Striplin via Mercedes  writes:
>
> > Just noticed outside unit was shut off again. Coils had no frost on them
> at all but it was in low pressure lockout. Reset it and forced a defrost
> away way. It’s down to -4 at the moment. I wonder if it’s just too damn
> cold for it and pressure is dropping, or if it really is low on charge. If
> so, can these things even be charged in the winter? Or do they have to be
> done during the warmer months? Btw supposed to get down to -14 tonight.
> >
> > Sent from my iPhone
> >
> >> On Feb 15, 2021, at 5:23 PM, Kaleb Striplin  wrote:
> >>
> >> Checked it a little while ago and the coils are clear.
> >>
> >>> On 2/15/2021 3:22 PM, Kaleb Striplin wrote:
> >>> It’s been running all day without issue. I can’t say I have noticed if
> it’s ran a defrost cycle or not. I think here shortly I will go out and
> look at the coils and see if they are clear or have started frosting up
> again.
> >>>
> >>> Sent from my iPhone
> >>>
> >>>>> On Feb 15, 2021, at 2:17 PM, Scott Ritchey via Mercedes <
> mercedes@okiebenz.com> wrote:
> >>>>
> >>>> Probably, given the outside temps and state of charge, the gas
> pressure going into the compressor gets too low if ice prevents the coils
> from absorbing enough heat to raise the pressure (from that very cold air).
> >>>>
> >>>> -Original Message-
> >>>> From: Mercedes On Behalf Of Kaleb Striplin via Mercedes
> >>>> Sent: Monday, February 15, 2021 10:31 AM
> >>>> To: mercedes@okiebenz.com
> >>>> Cc: Kaleb Striplin 
> >>>> Subject: Re: [MBZ] Heat pump question
> >>>>
> >>>> Well I went out and checked it.  When I looked at in there was no
> frost on the coils that I could see in the center part.  I pulled the cover
> and sure enough it was blinking a low pressure lockout. With the side cover
> off I could see some frost on the outside of the coils, not a whole lot
> though.  I shorted the test pins to reset it and it kicked back on.  I
> shorted them again to force a defrost.  Defrost ran for about 5-10 minutes
> and once frost was clear it kicked back into heat mode.
> >>>>
> >>>> Since replacing the defrost board with attached sensor last year, I
> have not had a problem sense.  Why the heck did it happen again?  I know it
> has a temp sensor for the coils.  Do these work by going into a defrost
> cycle on a timed basis if the temp sensor is below a certain temp?  Or do
> they sense the coils are freezing up and enter defrost when needed (not on
> a timed scheduled).
> >>>>
> >>>> From what I recall, some old systems did not have a temp sensor and
> just went into defrost every so often.  I think some systems sense when it
> needs to be done.  Others I think are still timed but only do it when temp
> is below a certain point.  This is a 2008 Rheem running on 410 so I am not
> sure.  If mine runs on a timer only when temp gets low maybe it is so cold
> that it simply did not reach its run time to defrost soon enough before it
> started frosting up, or perhaps it is sucking in blowing snow which caused
> it to frost up faster?
> >>>>
> >>>>> On 2/15/2021 9:03 AM, Kaleb Striplin via Mercedes wrote:
> >>>>> It is now -3 outside, not sure how low it got last night. Anyway,
> heat
> >>>>> pump has been running pretty much non stop for the last few days with
> >>>>> the aux heat kicking on occasionally. Yesterday afternoon aux heat
> was
> >>>>> on quite a bit as it never got over 4 yesterday.  This morning when I
> >>>>> woke up outside unit was running as normal.  A little while later I
> >>>>> happen to look out and it is shut down. Normally when it goes into
> >>&

Re: [MBZ] Heat pump question

[Scott Ritchey via Mercedes]

When all else fails, read the instructions?  The basic setup is the same for 
most heat pump systems except for details like TXV vs piston/orifice.  But the 
control electronics (typically on a defrost control board) can do anything, 
like totally shut down below some temp.  Might be worth downloading and 
browsing the owners' manual (or might not; some are much worse than others).

-Original Message-
From: Mercedes On Behalf Of Kaleb Striplin via Mercedes
Sent: Monday, February 15, 2021 11:52 PM
To: Kaleb Striplin via Mercedes 
Cc: Kaleb Striplin 
Subject: Re: [MBZ] Heat pump question

Sounds like the unit just kicked back on. Guess we shall see how the night 
goes. 

Sent from my iPhone

> On Feb 15, 2021, at 10:44 PM, Kaleb Striplin via Mercedes 
>  wrote:
> 
> I will be damned if it isn’t shut off again. Can say for sure about last 
> time but this time code is for low pressure switch open, not the same low 
> pressure lockout as before. Don’t see any loose or damaged wires to any 
> pressure switches. Jumping the pins didn’t reset it either. Guess it will be 
> expensive aux heat tonight. 
> 
> Sent from my iPhone
> 
>> On Feb 15, 2021, at 10:23 PM, Kaleb Striplin  wrote:
>> 
>> Just noticed outside unit was shut off again. Coils had no frost on them at 
>> all but it was in low pressure lockout. Reset it and forced a defrost away 
>> way. It’s down to -4 at the moment. I wonder if it’s just too damn cold for 
>> it and pressure is dropping, or if it really is low on charge. If so, can 
>> these things even be charged in the winter? Or do they have to be done 
>> during the warmer months? Btw supposed to get down to -14 tonight. 
>> 
>> Sent from my iPhone
>> 
>>>> On Feb 15, 2021, at 5:23 PM, Kaleb Striplin  wrote:
>>> 
>>> Checked it a little while ago and the coils are clear.
>>> 
>>>>> On 2/15/2021 3:22 PM, Kaleb Striplin wrote:
>>>> It’s been running all day without issue. I can’t say I have noticed if 
>>>> it’s ran a defrost cycle or not. I think here shortly I will go out and 
>>>> look at the coils and see if they are clear or have started frosting up 
>>>> again.
>>>> 
>>>> Sent from my iPhone
>>>> 
>>>>>> On Feb 15, 2021, at 2:17 PM, Scott Ritchey via Mercedes 
>>>>>>  wrote:
>>>>> 
>>>>> Probably, given the outside temps and state of charge, the gas pressure 
>>>>> going into the compressor gets too low if ice prevents the coils from 
>>>>> absorbing enough heat to raise the pressure (from that very cold air).
>>>>> 
>>>>> -Original Message-
>>>>> From: Mercedes On Behalf Of Kaleb Striplin via Mercedes
>>>>> Sent: Monday, February 15, 2021 10:31 AM
>>>>> To: mercedes@okiebenz.com
>>>>> Cc: Kaleb Striplin 
>>>>> Subject: Re: [MBZ] Heat pump question
>>>>> 
>>>>> Well I went out and checked it.  When I looked at in there was no frost 
>>>>> on the coils that I could see in the center part.  I pulled the cover and 
>>>>> sure enough it was blinking a low pressure lockout. With the side cover 
>>>>> off I could see some frost on the outside of the coils, not a whole lot 
>>>>> though.  I shorted the test pins to reset it and it kicked back on.  I 
>>>>> shorted them again to force a defrost.  Defrost ran for about 5-10 
>>>>> minutes and once frost was clear it kicked back into heat mode.
>>>>> 
>>>>> Since replacing the defrost board with attached sensor last year, I have 
>>>>> not had a problem sense.  Why the heck did it happen again?  I know it 
>>>>> has a temp sensor for the coils.  Do these work by going into a defrost 
>>>>> cycle on a timed basis if the temp sensor is below a certain temp?  Or do 
>>>>> they sense the coils are freezing up and enter defrost when needed (not 
>>>>> on a timed scheduled).
>>>>> 
>>>>> From what I recall, some old systems did not have a temp sensor and just 
>>>>> went into defrost every so often.  I think some systems sense when it 
>>>>> needs to be done.  Others I think are still timed but only do it when 
>>>>> temp is below a certain point.  This is a 2008 Rheem running on 410 so I 
>>>>> am not sure.  If mine runs on a timer only when temp gets low maybe it is 
>>>>> so cold that it simply did not reach its run time to defrost soon enough 
>>>>> before

Re: [MBZ] Heat pump question

[Buggered Benzmail via Mercedes]

Yeah a heat pump doesn’t have much to work with at those temps

--FT
Sent from iPhone

> On Feb 15, 2021, at 11:44 PM, Allan Streib via Mercedes 
>  wrote:
> 
> I think you're below the temps where a ambient-air heat pump really does
> anything at all. But as I said earlier I'm not speaking from experience.
> 
> I'd fire up the wood stove if it were me.
> 
> Allan
> 
> 
> Kaleb Striplin via Mercedes  writes:
> 
>> Just noticed outside unit was shut off again. Coils had no frost on them at 
>> all but it was in low pressure lockout. Reset it and forced a defrost away 
>> way. It’s down to -4 at the moment. I wonder if it’s just too damn cold for 
>> it and pressure is dropping, or if it really is low on charge. If so, can 
>> these things even be charged in the winter? Or do they have to be done 
>> during the warmer months? Btw supposed to get down to -14 tonight. 
>> 
>> Sent from my iPhone
>> 
>>>> On Feb 15, 2021, at 5:23 PM, Kaleb Striplin  wrote:
>>> 
>>> Checked it a little while ago and the coils are clear.
>>> 
>>>> On 2/15/2021 3:22 PM, Kaleb Striplin wrote:
>>>> It’s been running all day without issue. I can’t say I have noticed if 
>>>> it’s ran a defrost cycle or not. I think here shortly I will go out and 
>>>> look at the coils and see if they are clear or have started frosting up 
>>>> again.
>>>> 
>>>> Sent from my iPhone
>>>> 
>>>>>> On Feb 15, 2021, at 2:17 PM, Scott Ritchey via Mercedes 
>>>>>>  wrote:
>>>>> 
>>>>> Probably, given the outside temps and state of charge, the gas pressure 
>>>>> going into the compressor gets too low if ice prevents the coils from 
>>>>> absorbing enough heat to raise the pressure (from that very cold air).
>>>>> 
>>>>> -Original Message-
>>>>> From: Mercedes On Behalf Of Kaleb Striplin via Mercedes
>>>>> Sent: Monday, February 15, 2021 10:31 AM
>>>>> To: mercedes@okiebenz.com
>>>>> Cc: Kaleb Striplin 
>>>>> Subject: Re: [MBZ] Heat pump question
>>>>> 
>>>>> Well I went out and checked it.  When I looked at in there was no frost 
>>>>> on the coils that I could see in the center part.  I pulled the cover and 
>>>>> sure enough it was blinking a low pressure lockout. With the side cover 
>>>>> off I could see some frost on the outside of the coils, not a whole lot 
>>>>> though.  I shorted the test pins to reset it and it kicked back on.  I 
>>>>> shorted them again to force a defrost.  Defrost ran for about 5-10 
>>>>> minutes and once frost was clear it kicked back into heat mode.
>>>>> 
>>>>> Since replacing the defrost board with attached sensor last year, I have 
>>>>> not had a problem sense.  Why the heck did it happen again?  I know it 
>>>>> has a temp sensor for the coils.  Do these work by going into a defrost 
>>>>> cycle on a timed basis if the temp sensor is below a certain temp?  Or do 
>>>>> they sense the coils are freezing up and enter defrost when needed (not 
>>>>> on a timed scheduled).
>>>>> 
>>>>> From what I recall, some old systems did not have a temp sensor and just 
>>>>> went into defrost every so often.  I think some systems sense when it 
>>>>> needs to be done.  Others I think are still timed but only do it when 
>>>>> temp is below a certain point.  This is a 2008 Rheem running on 410 so I 
>>>>> am not sure.  If mine runs on a timer only when temp gets low maybe it is 
>>>>> so cold that it simply did not reach its run time to defrost soon enough 
>>>>> before it started frosting up, or perhaps it is sucking in blowing snow 
>>>>> which caused it to frost up faster?
>>>>> 
>>>>>> On 2/15/2021 9:03 AM, Kaleb Striplin via Mercedes wrote:
>>>>>> It is now -3 outside, not sure how low it got last night. Anyway, heat
>>>>>> pump has been running pretty much non stop for the last few days with
>>>>>> the aux heat kicking on occasionally. Yesterday afternoon aux heat was
>>>>>> on quite a bit as it never got over 4 yesterday.  This morning when I
>>>>>> woke up outside unit was running as normal.  A little while later I
>>>>>> happen to look out and it is shut down. Normally when it goes into
&

Re: [MBZ] Heat pump question

[Kaleb Striplin via Mercedes]

Sounds like the unit just kicked back on. Guess we shall see how the night 
goes. 

Sent from my iPhone

> On Feb 15, 2021, at 10:44 PM, Kaleb Striplin via Mercedes 
>  wrote:
> 
> I will be damned if it isn’t shut off again. Can say for sure about last 
> time but this time code is for low pressure switch open, not the same low 
> pressure lockout as before. Don’t see any loose or damaged wires to any 
> pressure switches. Jumping the pins didn’t reset it either. Guess it will be 
> expensive aux heat tonight. 
> 
> Sent from my iPhone
> 
>> On Feb 15, 2021, at 10:23 PM, Kaleb Striplin  wrote:
>> 
>> Just noticed outside unit was shut off again. Coils had no frost on them at 
>> all but it was in low pressure lockout. Reset it and forced a defrost away 
>> way. It’s down to -4 at the moment. I wonder if it’s just too damn cold for 
>> it and pressure is dropping, or if it really is low on charge. If so, can 
>> these things even be charged in the winter? Or do they have to be done 
>> during the warmer months? Btw supposed to get down to -14 tonight. 
>> 
>> Sent from my iPhone
>> 
>>>> On Feb 15, 2021, at 5:23 PM, Kaleb Striplin  wrote:
>>> 
>>> Checked it a little while ago and the coils are clear.
>>> 
>>>>> On 2/15/2021 3:22 PM, Kaleb Striplin wrote:
>>>> It’s been running all day without issue. I can’t say I have noticed if 
>>>> it’s ran a defrost cycle or not. I think here shortly I will go out and 
>>>> look at the coils and see if they are clear or have started frosting up 
>>>> again.
>>>> 
>>>> Sent from my iPhone
>>>> 
>>>>>> On Feb 15, 2021, at 2:17 PM, Scott Ritchey via Mercedes 
>>>>>>  wrote:
>>>>> 
>>>>> Probably, given the outside temps and state of charge, the gas pressure 
>>>>> going into the compressor gets too low if ice prevents the coils from 
>>>>> absorbing enough heat to raise the pressure (from that very cold air).
>>>>> 
>>>>> -Original Message-
>>>>> From: Mercedes On Behalf Of Kaleb Striplin via Mercedes
>>>>> Sent: Monday, February 15, 2021 10:31 AM
>>>>> To: mercedes@okiebenz.com
>>>>> Cc: Kaleb Striplin 
>>>>> Subject: Re: [MBZ] Heat pump question
>>>>> 
>>>>> Well I went out and checked it.  When I looked at in there was no frost 
>>>>> on the coils that I could see in the center part.  I pulled the cover and 
>>>>> sure enough it was blinking a low pressure lockout. With the side cover 
>>>>> off I could see some frost on the outside of the coils, not a whole lot 
>>>>> though.  I shorted the test pins to reset it and it kicked back on.  I 
>>>>> shorted them again to force a defrost.  Defrost ran for about 5-10 
>>>>> minutes and once frost was clear it kicked back into heat mode.
>>>>> 
>>>>> Since replacing the defrost board with attached sensor last year, I have 
>>>>> not had a problem sense.  Why the heck did it happen again?  I know it 
>>>>> has a temp sensor for the coils.  Do these work by going into a defrost 
>>>>> cycle on a timed basis if the temp sensor is below a certain temp?  Or do 
>>>>> they sense the coils are freezing up and enter defrost when needed (not 
>>>>> on a timed scheduled).
>>>>> 
>>>>> From what I recall, some old systems did not have a temp sensor and just 
>>>>> went into defrost every so often.  I think some systems sense when it 
>>>>> needs to be done.  Others I think are still timed but only do it when 
>>>>> temp is below a certain point.  This is a 2008 Rheem running on 410 so I 
>>>>> am not sure.  If mine runs on a timer only when temp gets low maybe it is 
>>>>> so cold that it simply did not reach its run time to defrost soon enough 
>>>>> before it started frosting up, or perhaps it is sucking in blowing snow 
>>>>> which caused it to frost up faster?
>>>>> 
>>>>>> On 2/15/2021 9:03 AM, Kaleb Striplin via Mercedes wrote:
>>>>>> It is now -3 outside, not sure how low it got last night. Anyway, heat
>>>>>> pump has been running pretty much non stop for the last few days with
>>>>>> the aux heat kicking on occasionally. Yesterday afternoon aux heat was
>>>>>> on quite a bit as it never got over 4 yesterday.  This morning when 

Re: [MBZ] Heat pump question

[Allan Streib via Mercedes]

I think you're below the temps where a ambient-air heat pump really does
anything at all. But as I said earlier I'm not speaking from experience.

I'd fire up the wood stove if it were me.

Allan


Kaleb Striplin via Mercedes  writes:

> Just noticed outside unit was shut off again. Coils had no frost on them at 
> all but it was in low pressure lockout. Reset it and forced a defrost away 
> way. It’s down to -4 at the moment. I wonder if it’s just too damn cold for 
> it and pressure is dropping, or if it really is low on charge. If so, can 
> these things even be charged in the winter? Or do they have to be done during 
> the warmer months? Btw supposed to get down to -14 tonight. 
>
> Sent from my iPhone
>
>> On Feb 15, 2021, at 5:23 PM, Kaleb Striplin  wrote:
>> 
>> Checked it a little while ago and the coils are clear.
>> 
>>> On 2/15/2021 3:22 PM, Kaleb Striplin wrote:
>>> It’s been running all day without issue. I can’t say I have noticed if it’s 
>>> ran a defrost cycle or not. I think here shortly I will go out and look at 
>>> the coils and see if they are clear or have started frosting up again.
>>> 
>>> Sent from my iPhone
>>> 
>>>>> On Feb 15, 2021, at 2:17 PM, Scott Ritchey via Mercedes 
>>>>>  wrote:
>>>> 
>>>> Probably, given the outside temps and state of charge, the gas pressure 
>>>> going into the compressor gets too low if ice prevents the coils from 
>>>> absorbing enough heat to raise the pressure (from that very cold air).
>>>> 
>>>> -Original Message-
>>>> From: Mercedes On Behalf Of Kaleb Striplin via Mercedes
>>>> Sent: Monday, February 15, 2021 10:31 AM
>>>> To: mercedes@okiebenz.com
>>>> Cc: Kaleb Striplin 
>>>> Subject: Re: [MBZ] Heat pump question
>>>> 
>>>> Well I went out and checked it.  When I looked at in there was no frost on 
>>>> the coils that I could see in the center part.  I pulled the cover and 
>>>> sure enough it was blinking a low pressure lockout. With the side cover 
>>>> off I could see some frost on the outside of the coils, not a whole lot 
>>>> though.  I shorted the test pins to reset it and it kicked back on.  I 
>>>> shorted them again to force a defrost.  Defrost ran for about 5-10 minutes 
>>>> and once frost was clear it kicked back into heat mode.
>>>> 
>>>> Since replacing the defrost board with attached sensor last year, I have 
>>>> not had a problem sense.  Why the heck did it happen again?  I know it has 
>>>> a temp sensor for the coils.  Do these work by going into a defrost cycle 
>>>> on a timed basis if the temp sensor is below a certain temp?  Or do they 
>>>> sense the coils are freezing up and enter defrost when needed (not on a 
>>>> timed scheduled).
>>>> 
>>>> From what I recall, some old systems did not have a temp sensor and just 
>>>> went into defrost every so often.  I think some systems sense when it 
>>>> needs to be done.  Others I think are still timed but only do it when temp 
>>>> is below a certain point.  This is a 2008 Rheem running on 410 so I am not 
>>>> sure.  If mine runs on a timer only when temp gets low maybe it is so cold 
>>>> that it simply did not reach its run time to defrost soon enough before it 
>>>> started frosting up, or perhaps it is sucking in blowing snow which caused 
>>>> it to frost up faster?
>>>> 
>>>>> On 2/15/2021 9:03 AM, Kaleb Striplin via Mercedes wrote:
>>>>> It is now -3 outside, not sure how low it got last night. Anyway, heat
>>>>> pump has been running pretty much non stop for the last few days with
>>>>> the aux heat kicking on occasionally. Yesterday afternoon aux heat was
>>>>> on quite a bit as it never got over 4 yesterday.  This morning when I
>>>>> woke up outside unit was running as normal.  A little while later I
>>>>> happen to look out and it is shut down. Normally when it goes into
>>>>> defrost it will shut down for a moment then fire back up pretty quick.
>>>>> It did not appear to be in a defrost cycle.  I had issues before where
>>>>> the temp sensor on the coils was evidentially bad because when it got
>>>>> below freezing it would seemingly randomly never enter defrost cycle
>>>>> and would frost over, which would then put it in a low pressure
>>>>> lockout. I would have to jum

Re: [MBZ] Heat pump question

[Kaleb Striplin via Mercedes]

I will be damned if it isn’t shut off again. Can say for sure about last time 
but this time code is for low pressure switch open, not the same low pressure 
lockout as before. Don’t see any loose or damaged wires to any pressure 
switches. Jumping the pins didn’t reset it either. Guess it will be expensive 
aux heat tonight. 

Sent from my iPhone

> On Feb 15, 2021, at 10:23 PM, Kaleb Striplin  wrote:
> 
> Just noticed outside unit was shut off again. Coils had no frost on them at 
> all but it was in low pressure lockout. Reset it and forced a defrost away 
> way. It’s down to -4 at the moment. I wonder if it’s just too damn cold for 
> it and pressure is dropping, or if it really is low on charge. If so, can 
> these things even be charged in the winter? Or do they have to be done during 
> the warmer months? Btw supposed to get down to -14 tonight. 
> 
> Sent from my iPhone
> 
>> On Feb 15, 2021, at 5:23 PM, Kaleb Striplin  wrote:
>> 
>> Checked it a little while ago and the coils are clear.
>> 
>>>> On 2/15/2021 3:22 PM, Kaleb Striplin wrote:
>>> It’s been running all day without issue. I can’t say I have noticed if it’s 
>>> ran a defrost cycle or not. I think here shortly I will go out and look at 
>>> the coils and see if they are clear or have started frosting up again.
>>> 
>>> Sent from my iPhone
>>> 
>>>>> On Feb 15, 2021, at 2:17 PM, Scott Ritchey via Mercedes 
>>>>>  wrote:
>>>> 
>>>> Probably, given the outside temps and state of charge, the gas pressure 
>>>> going into the compressor gets too low if ice prevents the coils from 
>>>> absorbing enough heat to raise the pressure (from that very cold air).
>>>> 
>>>> -Original Message-
>>>> From: Mercedes On Behalf Of Kaleb Striplin via Mercedes
>>>> Sent: Monday, February 15, 2021 10:31 AM
>>>> To: mercedes@okiebenz.com
>>>> Cc: Kaleb Striplin 
>>>> Subject: Re: [MBZ] Heat pump question
>>>> 
>>>> Well I went out and checked it.  When I looked at in there was no frost on 
>>>> the coils that I could see in the center part.  I pulled the cover and 
>>>> sure enough it was blinking a low pressure lockout. With the side cover 
>>>> off I could see some frost on the outside of the coils, not a whole lot 
>>>> though.  I shorted the test pins to reset it and it kicked back on.  I 
>>>> shorted them again to force a defrost.  Defrost ran for about 5-10 minutes 
>>>> and once frost was clear it kicked back into heat mode.
>>>> 
>>>> Since replacing the defrost board with attached sensor last year, I have 
>>>> not had a problem sense.  Why the heck did it happen again?  I know it has 
>>>> a temp sensor for the coils.  Do these work by going into a defrost cycle 
>>>> on a timed basis if the temp sensor is below a certain temp?  Or do they 
>>>> sense the coils are freezing up and enter defrost when needed (not on a 
>>>> timed scheduled).
>>>> 
>>>> From what I recall, some old systems did not have a temp sensor and just 
>>>> went into defrost every so often.  I think some systems sense when it 
>>>> needs to be done.  Others I think are still timed but only do it when temp 
>>>> is below a certain point.  This is a 2008 Rheem running on 410 so I am not 
>>>> sure.  If mine runs on a timer only when temp gets low maybe it is so cold 
>>>> that it simply did not reach its run time to defrost soon enough before it 
>>>> started frosting up, or perhaps it is sucking in blowing snow which caused 
>>>> it to frost up faster?
>>>> 
>>>>> On 2/15/2021 9:03 AM, Kaleb Striplin via Mercedes wrote:
>>>>> It is now -3 outside, not sure how low it got last night. Anyway, heat
>>>>> pump has been running pretty much non stop for the last few days with
>>>>> the aux heat kicking on occasionally. Yesterday afternoon aux heat was
>>>>> on quite a bit as it never got over 4 yesterday.  This morning when I
>>>>> woke up outside unit was running as normal.  A little while later I
>>>>> happen to look out and it is shut down. Normally when it goes into
>>>>> defrost it will shut down for a moment then fire back up pretty quick.
>>>>> It did not appear to be in a defrost cycle.  I had issues before where
>>>>> the temp sensor on the coils was evidentially bad because when it got
>>>>> below freezing it would seeming

Re: [MBZ] Heat pump question

[Kaleb Striplin via Mercedes]

Just noticed outside unit was shut off again. Coils had no frost on them at all 
but it was in low pressure lockout. Reset it and forced a defrost away way. 
It’s down to -4 at the moment. I wonder if it’s just too damn cold for it and 
pressure is dropping, or if it really is low on charge. If so, can these things 
even be charged in the winter? Or do they have to be done during the warmer 
months? Btw supposed to get down to -14 tonight. 

Sent from my iPhone

> On Feb 15, 2021, at 5:23 PM, Kaleb Striplin  wrote:
> 
> Checked it a little while ago and the coils are clear.
> 
>> On 2/15/2021 3:22 PM, Kaleb Striplin wrote:
>> It’s been running all day without issue. I can’t say I have noticed if it’s 
>> ran a defrost cycle or not. I think here shortly I will go out and look at 
>> the coils and see if they are clear or have started frosting up again.
>> 
>> Sent from my iPhone
>> 
>>>> On Feb 15, 2021, at 2:17 PM, Scott Ritchey via Mercedes 
>>>>  wrote:
>>> 
>>> Probably, given the outside temps and state of charge, the gas pressure 
>>> going into the compressor gets too low if ice prevents the coils from 
>>> absorbing enough heat to raise the pressure (from that very cold air).
>>> 
>>> -Original Message-
>>> From: Mercedes On Behalf Of Kaleb Striplin via Mercedes
>>> Sent: Monday, February 15, 2021 10:31 AM
>>> To: mercedes@okiebenz.com
>>> Cc: Kaleb Striplin 
>>> Subject: Re: [MBZ] Heat pump question
>>> 
>>> Well I went out and checked it.  When I looked at in there was no frost on 
>>> the coils that I could see in the center part.  I pulled the cover and sure 
>>> enough it was blinking a low pressure lockout. With the side cover off I 
>>> could see some frost on the outside of the coils, not a whole lot though.  
>>> I shorted the test pins to reset it and it kicked back on.  I shorted them 
>>> again to force a defrost.  Defrost ran for about 5-10 minutes and once 
>>> frost was clear it kicked back into heat mode.
>>> 
>>> Since replacing the defrost board with attached sensor last year, I have 
>>> not had a problem sense.  Why the heck did it happen again?  I know it has 
>>> a temp sensor for the coils.  Do these work by going into a defrost cycle 
>>> on a timed basis if the temp sensor is below a certain temp?  Or do they 
>>> sense the coils are freezing up and enter defrost when needed (not on a 
>>> timed scheduled).
>>> 
>>> From what I recall, some old systems did not have a temp sensor and just 
>>> went into defrost every so often.  I think some systems sense when it needs 
>>> to be done.  Others I think are still timed but only do it when temp is 
>>> below a certain point.  This is a 2008 Rheem running on 410 so I am not 
>>> sure.  If mine runs on a timer only when temp gets low maybe it is so cold 
>>> that it simply did not reach its run time to defrost soon enough before it 
>>> started frosting up, or perhaps it is sucking in blowing snow which caused 
>>> it to frost up faster?
>>> 
>>>> On 2/15/2021 9:03 AM, Kaleb Striplin via Mercedes wrote:
>>>> It is now -3 outside, not sure how low it got last night. Anyway, heat
>>>> pump has been running pretty much non stop for the last few days with
>>>> the aux heat kicking on occasionally. Yesterday afternoon aux heat was
>>>> on quite a bit as it never got over 4 yesterday.  This morning when I
>>>> woke up outside unit was running as normal.  A little while later I
>>>> happen to look out and it is shut down. Normally when it goes into
>>>> defrost it will shut down for a moment then fire back up pretty quick.
>>>> It did not appear to be in a defrost cycle.  I had issues before where
>>>> the temp sensor on the coils was evidentially bad because when it got
>>>> below freezing it would seemingly randomly never enter defrost cycle
>>>> and would frost over, which would then put it in a low pressure
>>>> lockout. I would have to jump the pins on the board to reset it and
>>>> force a defrost then it would be fine again for a while.  Last year I
>>>> replaced the defrost board which has the temp sensor hard wired on it.
>>>> Never had a problem since.
>>>> 
>>>> Anyway I was about to throw on a coat and go outside and pull the
>>>> cover and see if the board was flashing an error code and it started
>>>> back up.  It is now about an

Re: [MBZ] Heat pump question

[Kaleb Striplin via Mercedes]

Checked it a little while ago and the coils are clear.

On 2/15/2021 3:22 PM, Kaleb Striplin wrote:

It’s been running all day without issue. I can’t say I have noticed if it’s ran 
a defrost cycle or not. I think here shortly I will go out and look at the 
coils and see if they are clear or have started frosting up again.

Sent from my iPhone


On Feb 15, 2021, at 2:17 PM, Scott Ritchey via Mercedes  
wrote:

Probably, given the outside temps and state of charge, the gas pressure going 
into the compressor gets too low if ice prevents the coils from absorbing 
enough heat to raise the pressure (from that very cold air).

-Original Message-
From: Mercedes On Behalf Of Kaleb Striplin via Mercedes
Sent: Monday, February 15, 2021 10:31 AM
To: mercedes@okiebenz.com
Cc: Kaleb Striplin 
Subject: Re: [MBZ] Heat pump question

Well I went out and checked it.  When I looked at in there was no frost on the 
coils that I could see in the center part.  I pulled the cover and sure enough 
it was blinking a low pressure lockout. With the side cover off I could see 
some frost on the outside of the coils, not a whole lot though.  I shorted the 
test pins to reset it and it kicked back on.  I shorted them again to force a 
defrost.  Defrost ran for about 5-10 minutes and once frost was clear it kicked 
back into heat mode.

Since replacing the defrost board with attached sensor last year, I have not 
had a problem sense.  Why the heck did it happen again?  I know it has a temp 
sensor for the coils.  Do these work by going into a defrost cycle on a timed 
basis if the temp sensor is below a certain temp?  Or do they sense the coils 
are freezing up and enter defrost when needed (not on a timed scheduled).

 From what I recall, some old systems did not have a temp sensor and just went 
into defrost every so often.  I think some systems sense when it needs to be 
done.  Others I think are still timed but only do it when temp is below a 
certain point.  This is a 2008 Rheem running on 410 so I am not sure.  If mine 
runs on a timer only when temp gets low maybe it is so cold that it simply did 
not reach its run time to defrost soon enough before it started frosting up, or 
perhaps it is sucking in blowing snow which caused it to frost up faster?


On 2/15/2021 9:03 AM, Kaleb Striplin via Mercedes wrote:
It is now -3 outside, not sure how low it got last night. Anyway, heat
pump has been running pretty much non stop for the last few days with
the aux heat kicking on occasionally. Yesterday afternoon aux heat was
on quite a bit as it never got over 4 yesterday.  This morning when I
woke up outside unit was running as normal.  A little while later I
happen to look out and it is shut down. Normally when it goes into
defrost it will shut down for a moment then fire back up pretty quick.
It did not appear to be in a defrost cycle.  I had issues before where
the temp sensor on the coils was evidentially bad because when it got
below freezing it would seemingly randomly never enter defrost cycle
and would frost over, which would then put it in a low pressure
lockout. I would have to jump the pins on the board to reset it and
force a defrost then it would be fine again for a while.  Last year I
replaced the defrost board which has the temp sensor hard wired on it.
Never had a problem since.

Anyway I was about to throw on a coat and go outside and pull the
cover and see if the board was flashing an error code and it started
back up.  It is now about an hour later and I notice the outside unit
is not running again.  I am not sure how long it has not been running
but I know its probably be at least 10-15 minutes.  Is there some sort
of reason at these low temps that the outside unit would shut itself
down for a period of time then fire back up?  Does the system
determine that it is so cold outside that the outside unit is not
producing any heat anyway and shuts itself down for a while?  I will
wait a little bit longer and see what happens then go out in the
blowing snow to pull the cover and check the board to see if its
blinking any codes.


___
http://www.okiebenz.com

To search list archives http://www.okiebenz.com/archive/

To Unsubscribe or change delivery options go to:
http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com


___
http://www.okiebenz.com

To search list archives http://www.okiebenz.com/archive/

To Unsubscribe or change delivery options go to:
http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com



___
http://www.okiebenz.com

To search list archives http://www.okiebenz.com/archive/

To Unsubscribe or change delivery options go to:
http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com



___
http://www.okiebenz.com

To search list archives http://www.okiebenz.com/archive/

To Unsubscribe or change delivery options go to:
http

Re: [MBZ] Heat pump question

[Kaleb Striplin via Mercedes]

It’s been running all day without issue. I can’t say I have noticed if it’s ran 
a defrost cycle or not. I think here shortly I will go out and look at the 
coils and see if they are clear or have started frosting up again. 

Sent from my iPhone

> On Feb 15, 2021, at 2:17 PM, Scott Ritchey via Mercedes 
>  wrote:
> 
> Probably, given the outside temps and state of charge, the gas pressure 
> going into the compressor gets too low if ice prevents the coils from 
> absorbing enough heat to raise the pressure (from that very cold air).
> 
> -Original Message-
> From: Mercedes On Behalf Of Kaleb Striplin via Mercedes
> Sent: Monday, February 15, 2021 10:31 AM
> To: mercedes@okiebenz.com
> Cc: Kaleb Striplin 
> Subject: Re: [MBZ] Heat pump question
> 
> Well I went out and checked it.  When I looked at in there was no frost on 
> the coils that I could see in the center part.  I pulled the cover and sure 
> enough it was blinking a low pressure lockout. With the side cover off I 
> could see some frost on the outside of the coils, not a whole lot though.  I 
> shorted the test pins to reset it and it kicked back on.  I shorted them 
> again to force a defrost.  Defrost ran for about 5-10 minutes and once frost 
> was clear it kicked back into heat mode.
> 
> Since replacing the defrost board with attached sensor last year, I have not 
> had a problem sense.  Why the heck did it happen again?  I know it has a temp 
> sensor for the coils.  Do these work by going into a defrost cycle on a timed 
> basis if the temp sensor is below a certain temp?  Or do they sense the coils 
> are freezing up and enter defrost when needed (not on a timed scheduled).
> 
> From what I recall, some old systems did not have a temp sensor and just went 
> into defrost every so often.  I think some systems sense when it needs to be 
> done.  Others I think are still timed but only do it when temp is below a 
> certain point.  This is a 2008 Rheem running on 410 so I am not sure.  If 
> mine runs on a timer only when temp gets low maybe it is so cold that it 
> simply did not reach its run time to defrost soon enough before it started 
> frosting up, or perhaps it is sucking in blowing snow which caused it to 
> frost up faster?
> 
>> On 2/15/2021 9:03 AM, Kaleb Striplin via Mercedes wrote:
>> It is now -3 outside, not sure how low it got last night. Anyway, heat 
>> pump has been running pretty much non stop for the last few days with 
>> the aux heat kicking on occasionally. Yesterday afternoon aux heat was 
>> on quite a bit as it never got over 4 yesterday.  This morning when I 
>> woke up outside unit was running as normal.  A little while later I 
>> happen to look out and it is shut down. Normally when it goes into 
>> defrost it will shut down for a moment then fire back up pretty quick.  
>> It did not appear to be in a defrost cycle.  I had issues before where 
>> the temp sensor on the coils was evidentially bad because when it got 
>> below freezing it would seemingly randomly never enter defrost cycle 
>> and would frost over, which would then put it in a low pressure 
>> lockout. I would have to jump the pins on the board to reset it and 
>> force a defrost then it would be fine again for a while.  Last year I 
>> replaced the defrost board which has the temp sensor hard wired on it. 
>> Never had a problem since.
>> 
>> Anyway I was about to throw on a coat and go outside and pull the 
>> cover and see if the board was flashing an error code and it started 
>> back up.  It is now about an hour later and I notice the outside unit 
>> is not running again.  I am not sure how long it has not been running 
>> but I know its probably be at least 10-15 minutes.  Is there some sort 
>> of reason at these low temps that the outside unit would shut itself 
>> down for a period of time then fire back up?  Does the system 
>> determine that it is so cold outside that the outside unit is not 
>> producing any heat anyway and shuts itself down for a while?  I will 
>> wait a little bit longer and see what happens then go out in the 
>> blowing snow to pull the cover and check the board to see if its 
>> blinking any codes.
>> 
>> 
>> ___
>> http://www.okiebenz.com
>> 
>> To search list archives http://www.okiebenz.com/archive/
>> 
>> To Unsubscribe or change delivery options go to:
>> http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com
>> 
> 
> ___
> http://www.okiebenz.com
> 
> To search list archives http://www.okiebenz.com/archive/
> 
> To Unsu

Re: [MBZ] Heat pump question

[Scott Ritchey via Mercedes]

Probably, given the outside temps and state of charge, the gas pressure going 
into the compressor gets too low if ice prevents the coils from absorbing 
enough heat to raise the pressure (from that very cold air).

-Original Message-
From: Mercedes On Behalf Of Kaleb Striplin via Mercedes
Sent: Monday, February 15, 2021 10:31 AM
To: mercedes@okiebenz.com
Cc: Kaleb Striplin 
Subject: Re: [MBZ] Heat pump question

Well I went out and checked it.  When I looked at in there was no frost on the 
coils that I could see in the center part.  I pulled the cover and sure enough 
it was blinking a low pressure lockout. With the side cover off I could see 
some frost on the outside of the coils, not a whole lot though.  I shorted the 
test pins to reset it and it kicked back on.  I shorted them again to force a 
defrost.  Defrost ran for about 5-10 minutes and once frost was clear it kicked 
back into heat mode.

Since replacing the defrost board with attached sensor last year, I have not 
had a problem sense.  Why the heck did it happen again?  I know it has a temp 
sensor for the coils.  Do these work by going into a defrost cycle on a timed 
basis if the temp sensor is below a certain temp?  Or do they sense the coils 
are freezing up and enter defrost when needed (not on a timed scheduled).

 From what I recall, some old systems did not have a temp sensor and just went 
into defrost every so often.  I think some systems sense when it needs to be 
done.  Others I think are still timed but only do it when temp is below a 
certain point.  This is a 2008 Rheem running on 410 so I am not sure.  If mine 
runs on a timer only when temp gets low maybe it is so cold that it simply did 
not reach its run time to defrost soon enough before it started frosting up, or 
perhaps it is sucking in blowing snow which caused it to frost up faster?

On 2/15/2021 9:03 AM, Kaleb Striplin via Mercedes wrote:
> It is now -3 outside, not sure how low it got last night. Anyway, heat 
> pump has been running pretty much non stop for the last few days with 
> the aux heat kicking on occasionally. Yesterday afternoon aux heat was 
> on quite a bit as it never got over 4 yesterday.  This morning when I 
> woke up outside unit was running as normal.  A little while later I 
> happen to look out and it is shut down. Normally when it goes into 
> defrost it will shut down for a moment then fire back up pretty quick.  
> It did not appear to be in a defrost cycle.  I had issues before where 
> the temp sensor on the coils was evidentially bad because when it got 
> below freezing it would seemingly randomly never enter defrost cycle 
> and would frost over, which would then put it in a low pressure 
> lockout. I would have to jump the pins on the board to reset it and 
> force a defrost then it would be fine again for a while.  Last year I 
> replaced the defrost board which has the temp sensor hard wired on it. 
> Never had a problem since.
>
> Anyway I was about to throw on a coat and go outside and pull the 
> cover and see if the board was flashing an error code and it started 
> back up.  It is now about an hour later and I notice the outside unit 
> is not running again.  I am not sure how long it has not been running 
> but I know its probably be at least 10-15 minutes.  Is there some sort 
> of reason at these low temps that the outside unit would shut itself 
> down for a period of time then fire back up?  Does the system 
> determine that it is so cold outside that the outside unit is not 
> producing any heat anyway and shuts itself down for a while?  I will 
> wait a little bit longer and see what happens then go out in the 
> blowing snow to pull the cover and check the board to see if its 
> blinking any codes.
>
>
> ___
> http://www.okiebenz.com
>
> To search list archives http://www.okiebenz.com/archive/
>
> To Unsubscribe or change delivery options go to:
> http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com
>

___
http://www.okiebenz.com

To search list archives http://www.okiebenz.com/archive/

To Unsubscribe or change delivery options go to:
http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com



___
http://www.okiebenz.com

To search list archives http://www.okiebenz.com/archive/

To Unsubscribe or change delivery options go to:
http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com

Re: [MBZ] Heat pump question

[Scott Ritchey via Mercedes]

For recent systems there are two basic defrost schemes: demand defrost and 
time/temp defrost.  

Time/temp is cheaper and most common.  The time can usually be set by jumpers 
or DIP switches.  If time is set to 30 min (for example) the coil temp sensor 
is checked every 30 minutes and a defrost cycle starts if that temp is below 
some threshold, like 30 degrees, and stops when the coil temp sensor reaches 
(for example) cutoff at 60 degrees.  There is usually a maximum defrost cycle 
time limit.  In the defrost mode the heat pump acts like an AC unit except the 
aux/emergency heat strips are on and the outside fan is off.  This scheme will 
cause  unnecessary (but short) defrost cycles when it's near or below freezing 
outside.  Ice buildup is actually worst when the outside temp is near and just 
above 32 degrees and it's humid, not when it's very cold

Demand defrost uses one of several methods to estimate air flow restriction 
through the coils.  It may measure the pressure drop or try to compute it from 
refrigerant pressures or temperatures.  In theory this avoids unnecessary 
defrost cycles and insures the coils really are open.  I don't have experience 
with demand defrost systems.

-Original Message-
From: Mercedes On Behalf Of Kaleb Striplin via Mercedes
Sent: Monday, February 15, 2021 10:31 AM
To: mercedes@okiebenz.com
Cc: Kaleb Striplin 
Subject: Re: [MBZ] Heat pump question

Well I went out and checked it.  When I looked at in there was no frost on the 
coils that I could see in the center part.  I pulled the cover and sure enough 
it was blinking a low pressure lockout. With the side cover off I could see 
some frost on the outside of the coils, not a whole lot though.  I shorted the 
test pins to reset it and it kicked back on.  I shorted them again to force a 
defrost.  Defrost ran for about 5-10 minutes and once frost was clear it kicked 
back into heat mode.

Since replacing the defrost board with attached sensor last year, I have not 
had a problem sense.  Why the heck did it happen again?  I know it has a temp 
sensor for the coils.  Do these work by going into a defrost cycle on a timed 
basis if the temp sensor is below a certain temp?  Or do they sense the coils 
are freezing up and enter defrost when needed (not on a timed scheduled).

 From what I recall, some old systems did not have a temp sensor and just went 
into defrost every so often.  I think some systems sense when it needs to be 
done.  Others I think are still timed but only do it when temp is below a 
certain point.  This is a 2008 Rheem running on 410 so I am not sure.  If mine 
runs on a timer only when temp gets low maybe it is so cold that it simply did 
not reach its run time to defrost soon enough before it started frosting up, or 
perhaps it is sucking in blowing snow which caused it to frost up faster?

On 2/15/2021 9:03 AM, Kaleb Striplin via Mercedes wrote:
> It is now -3 outside, not sure how low it got last night. Anyway, heat 
> pump has been running pretty much non stop for the last few days with 
> the aux heat kicking on occasionally. Yesterday afternoon aux heat was 
> on quite a bit as it never got over 4 yesterday.  This morning when I 
> woke up outside unit was running as normal.  A little while later I 
> happen to look out and it is shut down. Normally when it goes into 
> defrost it will shut down for a moment then fire back up pretty quick.  
> It did not appear to be in a defrost cycle.  I had issues before where 
> the temp sensor on the coils was evidentially bad because when it got 
> below freezing it would seemingly randomly never enter defrost cycle 
> and would frost over, which would then put it in a low pressure 
> lockout. I would have to jump the pins on the board to reset it and 
> force a defrost then it would be fine again for a while.  Last year I 
> replaced the defrost board which has the temp sensor hard wired on it. 
> Never had a problem since.
>
> Anyway I was about to throw on a coat and go outside and pull the 
> cover and see if the board was flashing an error code and it started 
> back up.  It is now about an hour later and I notice the outside unit 
> is not running again.  I am not sure how long it has not been running 
> but I know its probably be at least 10-15 minutes.  Is there some sort 
> of reason at these low temps that the outside unit would shut itself 
> down for a period of time then fire back up?  Does the system 
> determine that it is so cold outside that the outside unit is not 
> producing any heat anyway and shuts itself down for a while?  I will 
> wait a little bit longer and see what happens then go out in the 
> blowing snow to pull the cover and check the board to see if its 
> blinking any codes.
>
>
> ___
> http://www.okiebenz.com
>
> To search list archives http://

Re: [MBZ] Heat pump question

[Allan Streib via Mercedes]

Kaleb Striplin via Mercedes  writes:

> Is there some sort of reason at these low temps that the outside unit
> would shut itself down for a period of time then fire back up?  Does
> the system determine that it is so cold outside that the outside unit
> is not producing any heat anyway and shuts itself down for a while?

I'm talking about something I really have no experience with, but is it
an R22 unit? R22 enthalpy drops to zero at -40F, but in practice a
residential heat pump doesn't really work below zero F. It would not
surprise me if the system had some minimum exterior temperature limit.

Allan

___
http://www.okiebenz.com

To search list archives http://www.okiebenz.com/archive/

To Unsubscribe or change delivery options go to:
http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com

Re: [MBZ] Heat pump question

[Kaleb Striplin via Mercedes]

Well I went out and checked it.  When I looked at in there was no frost 
on the coils that I could see in the center part.  I pulled the cover 
and sure enough it was blinking a low pressure lockout. With the side 
cover off I could see some frost on the outside of the coils, not a 
whole lot though.  I shorted the test pins to reset it and it kicked 
back on.  I shorted them again to force a defrost.  Defrost ran for 
about 5-10 minutes and once frost was clear it kicked back into heat mode.


Since replacing the defrost board with attached sensor last year, I have 
not had a problem sense.  Why the heck did it happen again?  I know it 
has a temp sensor for the coils.  Do these work by going into a defrost 
cycle on a timed basis if the temp sensor is below a certain temp?  Or 
do they sense the coils are freezing up and enter defrost when needed 
(not on a timed scheduled).


From what I recall, some old systems did not have a temp sensor and 
just went into defrost every so often.  I think some systems sense when 
it needs to be done.  Others I think are still timed but only do it when 
temp is below a certain point.  This is a 2008 Rheem running on 410 so I 
am not sure.  If mine runs on a timer only when temp gets low maybe it 
is so cold that it simply did not reach its run time to defrost soon 
enough before it started frosting up, or perhaps it is sucking in 
blowing snow which caused it to frost up faster?


On 2/15/2021 9:03 AM, Kaleb Striplin via Mercedes wrote:
It is now -3 outside, not sure how low it got last night. Anyway, heat 
pump has been running pretty much non stop for the last few days with 
the aux heat kicking on occasionally. Yesterday afternoon aux heat was 
on quite a bit as it never got over 4 yesterday.  This morning when I 
woke up outside unit was running as normal.  A little while later I 
happen to look out and it is shut down. Normally when it goes into 
defrost it will shut down for a moment then fire back up pretty 
quick.  It did not appear to be in a defrost cycle.  I had issues 
before where the temp sensor on the coils was evidentially bad because 
when it got below freezing it would seemingly randomly never enter 
defrost cycle and would frost over, which would then put it in a low 
pressure lockout. I would have to jump the pins on the board to reset 
it and force a defrost then it would be fine again for a while.  Last 
year I replaced the defrost board which has the temp sensor hard wired 
on it. Never had a problem since.


Anyway I was about to throw on a coat and go outside and pull the 
cover and see if the board was flashing an error code and it started 
back up.  It is now about an hour later and I notice the outside unit 
is not running again.  I am not sure how long it has not been running 
but I know its probably be at least 10-15 minutes.  Is there some sort 
of reason at these low temps that the outside unit would shut itself 
down for a period of time then fire back up?  Does the system 
determine that it is so cold outside that the outside unit is not 
producing any heat anyway and shuts itself down for a while?  I will 
wait a little bit longer and see what happens then go out in the 
blowing snow to pull the cover and check the board to see if its 
blinking any codes.



___
http://www.okiebenz.com

To search list archives http://www.okiebenz.com/archive/

To Unsubscribe or change delivery options go to:
http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com



___
http://www.okiebenz.com

To search list archives http://www.okiebenz.com/archive/

To Unsubscribe or change delivery options go to:
http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com

[MBZ] Heat pump question

[Kaleb Striplin via Mercedes]

It is now -3 outside, not sure how low it got last night. Anyway, heat 
pump has been running pretty much non stop for the last few days with 
the aux heat kicking on occasionally. Yesterday afternoon aux heat was 
on quite a bit as it never got over 4 yesterday.  This morning when I 
woke up outside unit was running as normal.  A little while later I 
happen to look out and it is shut down.  Normally when it goes into 
defrost it will shut down for a moment then fire back up pretty quick.  
It did not appear to be in a defrost cycle.  I had issues before where 
the temp sensor on the coils was evidentially bad because when it got 
below freezing it would seemingly randomly never enter defrost cycle and 
would frost over, which would then put it in a low pressure lockout. I 
would have to jump the pins on the board to reset it and force a defrost 
then it would be fine again for a while.  Last year I replaced the 
defrost board which has the temp sensor hard wired on it. Never had a 
problem since.


Anyway I was about to throw on a coat and go outside and pull the cover 
and see if the board was flashing an error code and it started back up.  
It is now about an hour later and I notice the outside unit is not 
running again.  I am not sure how long it has not been running but I 
know its probably be at least 10-15 minutes.  Is there some sort of 
reason at these low temps that the outside unit would shut itself down 
for a period of time then fire back up?  Does the system determine that 
it is so cold outside that the outside unit is not producing any heat 
anyway and shuts itself down for a while?  I will wait a little bit 
longer and see what happens then go out in the blowing snow to pull the 
cover and check the board to see if its blinking any codes.



___
http://www.okiebenz.com

To search list archives http://www.okiebenz.com/archive/

To Unsubscribe or change delivery options go to:
http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com