RE: X Problems with newly added user
On Fri, 13 Apr 2001, Warren Melnick wrote: > is she running on the console or is she a remote user? Console. She's running as a second user on my laptop. > -Original Message----- > From: Stephen E. Hargrove [mailto:[EMAIL PROTECTED]] > Sent: Friday, April 13, 2001 12:10 PM > To: [EMAIL PROTECTED] > Subject: X Problems with newly added user > > > > I've just added a new user to my system (RH6.1), and she can't fire up X. > When she enters startx, it creates .Xauthority, and then craps out with > > _IceTransSocketCreateListener: failed to bind listener > _IceTransSocketUNIXCreateListener: ...SocketCreateListener() failed > _IceTransMakeAllCOTServerListeners: failed to create listener for local > > ** WARNING ** Cannot establish any listening sockets > > I've read through several posts by searching goole.com and several man > pages on xauth, Xsecurity, xhost, etc., but can't seem to get anywhere. > (As a side note, her DISPLAY environment variable isn't getting set > either.) > > I need to get her up rather quickly, so any advice or pointers (or better > yet, solutions :) will be most welcome. > > -- steve * Linux: http://exitwound.org Mozart: http://mozart.sourceforge.net Buck: http://www.BuckOwensFan.com * ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
X Problems with newly added user
I've just added a new user to my system (RH6.1), and she can't fire up X. When she enters startx, it creates .Xauthority, and then craps out with _IceTransSocketCreateListener: failed to bind listener _IceTransSocketUNIXCreateListener: ...SocketCreateListener() failed _IceTransMakeAllCOTServerListeners: failed to create listener for local ** WARNING ** Cannot establish any listening sockets I've read through several posts by searching goole.com and several man pages on xauth, Xsecurity, xhost, etc., but can't seem to get anywhere. (As a side note, her DISPLAY environment variable isn't getting set either.) I need to get her up rather quickly, so any advice or pointers (or better yet, solutions :) will be most welcome. -- steve * Linux: http://exitwound.org Mozart: http://mozart.sourceforge.net Buck: http://www.BuckOwensFan.com * ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
Re: rmmod
Ed Lazor wrote: > >It is being run as a cron job to remove unused modules. Take a look at > >/etc/cron.d/kmod to see how it is being run. If you don't want it to run, > >then you will have to manualy take care of removing unneeded modules. > > But... - dumb question here - ... aren't the necessary ones loaded at > boot time and that's all there is to it? > yes, they're also loaded as their needed. for example, i have floppy support compiled as a module. when i mount the floppy drive, the module loads. rmmod ensures that it's unloaded later, when i'm not using it. it doesn't hurt to leave it as a cronjob. -- steve ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
Can't open /dev/modem
everything was working fine, then i opened a webpage that was apparently quite a resource hog (i watched it eat /all/ of my available ram). my system hung, and i was forced to power off. now, when i fire up gnome-ppp, pppd dies with the following message in my log file: Nov 6 21:11:26 calypso pppd[1084]: Failed to open /dev/modem: Permission denied here's the ls on /dev/modem and /dev/ttyS2: lrwxrwxrwx 1 root root 10 Nov 6 21:04 /dev/modem -> /dev/ttyS2 crwSr-Sr-- 1 root tty4, 66 Nov 6 21:12 /dev/ttyS2 what do i need to do to allow me to again gain access to /dev/modem without su root? thanks! -- steve ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
Re: Samba problems - can't mount
Glen Lee Edwards wrote: > I'm trying to mount linux box "a" to linux box "b" or vice versa. Both > are running samba-2.0.7-4.i386.rpm, samba-client-2.0.7-4.i386, and > samba-common-2.0.7-4.i386. I have the following in /etc/fstab: i could be wrong about this, but if you're connecting two linux boxes, shouldn't you be using nfs instead of samba? -- steve ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
Re: Find IP for DSL
John Aldrich wrote: > On Fri, 03 Nov 2000, Gordon Messmer wrote: > > On Fri, 3 Nov 2000, John Aldrich wrote: > > > > > Hmm...ever think of tracerouting to your ISP's router and getting > > > YOUR address? :-) > > > > traceroute doesn't do that for me on any machine I've got :) > > > > My DSL modem doesn't even alter the TTL, so it doesn't show up in the > > traceroute. > > > Hmm...you know...that *could* be a problem...maybe there's > an interface on the DSL modem (telnet or web???) that'll > show that info. I know my Netgear ISDN router will tell me > that info if I go to the right menu option when telnetted > in. my cayman dsl modem has this same feature, which is accessible through a browser. i wrote a short perl job to fetch the page, pull the ip addy, compare it to the previous ip addy, and email me if and when it changes. i guess it all depends on the type of modem you're using. -- steve ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
USB WebCams
Hey all. I'm in the market for a new webcam, preferably USB. I've checked out the Linux-USB site, and they have several webcams which seem to work, but the list seems mixed between quality and useability. Does anyone have any recommendations as to which camera (1) is good quality as to video/audio performance and (2) works with Linux? Thanks! -- Steve ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
Re: Kernel config file
"Christopher W. Aiken" wrote: > When I run make xconfig to set up a new kernel, > one of the "option buttons" is to "load config file". > > My question is how can I make a "config" file > from my current running kernel? I would like this > config file as a starting point for when I build > a new kernel. cd /usr/src/linux make oldconfig it may not be exact, so you'll need to check it over before relying on it. -- Steve ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
Re: will linux recognise extra controller and harddisks
[EMAIL PROTECTED] wrote: > > I am thinking of adding 2 hard disks and control to access them > The controller is a Promise Ultra 66 and couple of 30 GB hard > disks > > What is good controller for Linux at a fair price if this one won't do the job ? > The Promise Ultra 66 will work. See http://www.ibiblio.org/mdw/HOWTO/mini/Ultra-DMA.html for more information and how to make it work. -- Steve ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
Re: SIIG UltraATA 66 PCI Controller CN2468
Robert James Steele wrote: > > I followed the Instructions and typed in > ide2=0xefa8,0xefe0 ide3=0xeff0,0xfe4 > > and it found hde and hdf > but when I go do a fdisk /dev/hde > i get "Unable to open /dev/hde" > > any ideas? I had this same problem. It was solved by executing /sbin/insmod ide-disk Of course, I had compiled ide support as a module. YMMV. -- Steve ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
Re: Need help setting up a stand-alone HP network printer
Jonathan Wilson wrote: > Howdy, > > In our office we have a network laser printer, the kind with it's own ethernet card. >It's an HP. I'm pretty sure we can set up Linux to print to it, but I can't figure >out how - I tried printtool, but I'm not sure if it's an SMB printer or what. > > Any ideas? I'm running an HP 2100TN. I *think* I set it up as a SMB/Win95. Following is the config from printtool: Name: lp0|hp2|hp2000tn Spool Directory: /var/spool/lpd/lp File Limit in KB: 0 Remote Host: hp2000tn Remote Queue: RAW Input Filter: *auto* - PostScript Then I added the following line to my /etc/hosts file: 192.168.2.50hp2000tn Hope this helps! -- Steve ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
Re: SIIG UltraATA 66 PCI Controller CN2468
Robert James Steele wrote: > Hi All > > I have a SIIG UltraATA 66 PCI IDE Controller Model CN2468 > (http://www.siig.com/ide/ultraata_66_pci.html) Info > (http://www.siig.com/ide/ultraata_66_pci_specs.html) Specifications > and am wondering if there are linux Drivers > for this hardware. What kernel version are you running? I just finished this battle. The HOWTO at http://www.ibiblio.org/mdw/HOWTO/mini/Ultra-DMA.html should walk you through it (for the most part). -- Steve ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
Re: starting apache
Bob Hartung wrote: > > Hi, > I am making progress. Apache, postgresql installed. Now > trying to make apache autostart on boot. I could place a > line in rc.local something like: > >/usr/local/apache/bin/apachectl start > > but is there a way to place a file in init.d and then link > to it from rc5.d? > Hi Bob. Just place the statement in your /etc/rc.d/rc.local file. That should do the trick. -- Steve ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
Re: make apache with php4
Bob Hartung wrote: > Jeff, > Yesss I did. - several times. My confusion arises as to whether the > file libphp3.a is proper since I am using php4. This is probably just an > example of my "newbie-ishness" but why would I want to call a php3 file when > installing php4 unless apache simply is using php3 as an alias for any verison > of php? the INSTALL file that came with my php4 distribution says to do this: cd apache_1.3.x ./configure --prefix=//apache \ --activate-module=src/modules/php4/libphp4.a make make install -- Steve ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
Re: cdrom
Jimmie Brandon wrote: > I am runnug rh6.1. I mounted my cdrom. > My question is how do I read the files on the cdrom > and > how do I run or execute a file from the cdrom? where did you mount the cdrom? mine mounts at /mnt/cdrom, so to see the files, ls /mnt/cdrom to execute a file, /mnt/cdrom/program_to_execute if you're not sure where the cdrom mounts at, look at /etc/fstab for an entry that looks something like this: /dev/cdrom /mnt/cdrom iso9660 noauto,owner,ro 0 0 the second colum (/mnt/cdrom) is the directory where it's mounted. -- Steve ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
Re: POP3
Okay, I've gotten past the denial problem. I modified my hosts.allow, and the system is now letting me in. However, it doesn't recognize my password. I'm running RH6.2, and I've configured gnu-pop3d with PAM. However, when I try to retrieve my mail, the system responds with: Could not log in to the mail server. The server responded: Bad login Please enter new password So, apparently I've not configured gnu-pop3d correctly as it's not correctly locating my password. Does anyone have any experience with this? The documentation for gnu-pop3d is fairly sparse. Thanks! -- Steve ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
Re: POP Mail
I just checked my log files and saw the following: Oct 15 12:31:46 pappy gnu-pop3d[12161]: refused connect from 208-192-8-114.apex2000.net which seems to indicate that the pop3 request is making it through my firewall, but that the daemon is refusing to accept it. Do I need to add something to my hosts.allow file to allow the connection, and if so, what? Thanks! -- Steve ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
Re: POP Mail
Mike Burger wrote: > Default installations don't seem to include a POP3 daemon. You just need > to install one. I've used cucipop, and gnu-pop3d...both with good results. Anthony E. Greene wrote: > Generally, the error messages given by GUI mail client are not specific > enough to troubleshoot these problems. Use telnet from a machine outside the > firewll and post the exact error message given: > > telnet servername 110 > Okay, I've installed gnu-pop3d and modified my inetd.conf as follows (and no, I don't know what I'm doing ;) : # Pop and imap mail services et al # pop-2 stream tcp nowait root/usr/sbin/tcpd ipop2d pop-3 stream tcp nowait root/usr/sbin/tcpd gnu-pop3d gnu-pop3d is locate in /usr/local/sbin/ and I've create a symlink in /usr/sbin to point to it (just to ensure that it would be found when needed). Following is the applicable portion of my netstat -ap: Active Internet connections (servers and established) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp0 0 *:pop-3 *:* LISTEN 12052/inetd tcp0 0 *:pop-2 *:* LISTEN 12052/inetd So, it appears that the system is listening for the pop3 connection, right? I've got telnet pretty much locked down so that only I can get in through ssh. When I try to telnet to port 110, the system closes the connection with the following message: warning: Authentication failed. Disconnected; connection lost (Connection closed by remote host.). When I try it with the normal telnet (/usr/bin/telnet) to port 110, I get the following: Trying 63.101.116.77... Connected to www.eesquire.com. Escape character is '^]'. Connection closed by foreign host. I get the exact same response when I open standard telnet services in inetd.conf and restart inet. Clearly, I don't know what I'm doing. If anyone has suggestions as to how I should proceed, I'm all eyes. Thanks! -- Steve ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
Re: RH 6.2 and Ultra 66 problem
Michael McLeod wrote: > I tried the Kernel RPM route but I just could not get it right. So I decided > to go the patch route but the PATCH program does not recognize my kernel as a > real file. My kernel is at: /usr/src/linux-2.2.14 (patch would like to find > it at /usr/src/linux) I can't get patch to apply the patch. Can anyone help > me. Michael, if I'm understanding your problem correctly, you need to create a symbolic link. From /usr/src, enter this: ln -s linux-2.2.14 linux That'll make /usr/src/linux equivalent (or point) to /usr/src/linux-2.2.14. -- Steve ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
POP Mail
Hey all. I've set up my system to receive email, and according to /var/log/maillog and my local 'mail' (from the command prompt), it's receiving it just find. However, when I try to access my server remotely, my mail program says that there was a POP3 error and that I should contact my system admin. My server is behind a firewall, and I've opened ports 109 (pop2 - both TCP and UDP) and 110 (pop3 - both TCP and UDP) to point to 192.168.1.10, which is assigned to the network card receiving outside connections (i.e., http, etc.). I've also uncommented the appropriate lines in my /etc/inetd.conf and restarted inet. However, netstat -apn | grep 109 returns tcp0 0 0.0.0.0:109 0.0.0.0:* LISTEN 8879/inetd and netstat -apn | grep 110 returns tcp0 0 0.0.0.0:110 0.0.0.0:* LISTEN 8879/inetd and this would seem to indicate that although it's listening to the correct port, it's not looking to the correct IP address. Right? If so, how do I get it to listen to 192.168.1.10? I've looked through various log files, but I can't find anything which would indicate what the POP3 error might be (which would be correct since it's looking to 0.0.0.0:109 and 0.0.0.0:110 rather than 192.168.1.10). Can anyone point me to where I should be looking to get this bound to the correct IP address? Thanks! -- Steve ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
Re: rm and rmdir directives
Bob Hartung wrote: > rm -dR apache_1.3.12 > > and rmdir --ignore-fail-on-non-empty apache_1.3.12 try rm -rf apache_1.3.12 and it that doesn't work, try it as root. -- Steve ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
Log Message
Can anyone tell me why the following message keeps appearing in my log file? Oct 13 18:03:52 pappy modprobe: can't locate module char-major-5 It's been happening consistenly everytime I telnet into the machine. It's not a bother, but I'd really like to know how to make it go away. Thanks! -- Steve ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
Ultra66 Performance
Now that I have my disk online and working, I ran a few diagnostics. Unfortunately, I'm an idiot and don't really know if these numbers are good or bad, so I'm hoping someone here can shed some light on this. Here's the information on the disk. # hdparm -i /dev/hde Model=WDC WD450AA-00BAA0, FwRev=10.09K11, SerialNo=WD-WMA2E1419330 Config={ HardSect NotMFM HdSw>15uSec SpinMotCtl Fixed DTR>5Mbs FmtGapReq } RawCHS=16383/16/63, TrkSize=57600, SectSize=600, ECCbytes=40 BuffType=3(DualPortCache), BuffSize=2048kB, MaxMultSect=16, MultSect=off DblWordIO=no, maxPIO=2(fast), DMA=yes, maxDMA=0(slow) CurCHS=16383/16/63, CurSects=-66060037, LBA=yes LBA CHS=1023/256/63 Remapping, LBA=yes, LBAsects=87930864 tDMA={min:120,rec:120}, DMA modes: mword0 mword1 mword2 IORDY=on/off, tPIO={min:120,w/IORDY:120}, PIO modes: mode3 mode4 UDMA modes: mode0 mode1 mode2 According to the promotional material, the specs of the disk are as follows: Western Digital Caviar 45.0GB EIDE Ultra ATA/66 3.5LP 5400RPM 9.5MS Here's the disk performance: # hdparm -Tt /dev/hde /dev/hde: Timing buffer-cache reads: 128 MB in 2.75 seconds =46.55 MB/sec Timing buffered disk reads: 64 MB in 5.00 seconds =12.80 MB/sec And here's the current settings of the disk: # hdparm /dev/hde /dev/hde: multcount= 0 (off) I/O support = 0 (default 16-bit) unmaskirq= 0 (off) using_dma= 1 (on) keepsettings = 0 (off) nowerr = 0 (off) readonly = 0 (off) readahead= 8 (on) geometry = 5473/255/63, sectors = 87930864, start = 0 Here's the info on the /proc/ide/pdc202xx. Although the promotional materials state that the disk its ATA/66 and the PCI board is 66MHz, it appears to me that it's running at 33MHz. But, again, you've got to consider the idiot factor. # cat pdc202xx PDC20262 Chipset. --- General Status - Burst Mode : enabled Host Mode: Normal Bus Clocking : 33 PCI Internal IO pad select: 4 mA Status Polling Period: 14 Interrupt Check Status Polling Delay : 1 --- Primary Channel Secondary Channel - enabled enabled 66 Clocking enabled disabled Mode MASTER Mode MASTER FIFO Empty FIFO Empty --- drive0 - drive1 drive0 -- drive1 -- DMA enabled:yes no nono DMA Mode: UDMA 4 NOTSET NOTSET NOTSET PIO Mode: PIO 4NOTSET NOTSET NOTSET Here's the info in /proc/ide/ide2/hde/settings. I have no idea how or if I should affect these values: namevalue min max mode - --- --- bios_cyl54730 65535 rw bios_head 255 0 255 rw bios_sect 63 0 63 rw breada_readahead4 0 127 rw bswap 0 0 1 r current_speed 0 0 69 rw file_readahead 124 0 2097151 rw ide_scsi0 0 1 rw init_speed 0 0 69 rw io_32bit0 0 3 rw keepsettings0 0 1 rw lun 0 0 7 rw max_kb_per_request 64 1 127 rw multcount 0 0 8 rw nice1 1 0 1 rw nowerr 0 0 1 rw number 0 0 3 rw pio_modewrite-only 0 255 w slow0 0 1 rw unmaskirq 0 0 1 rw using_dma 1 0 1 rw Did I leave anything out? Can anyone tell me if the disk is performing up to snuff? And if not, what should I do to improve the performance? Thanks! -- Steve ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
Re: Promise Ultra66 SOLVED
Matt & Kristina Navarro-Haffner wrote: > > This is probably a really stupid suggestion at this point after all the > work you've done with it, but does /dev/hde really exist? And if so are > the major, minor numbers correct for ide2 (33,0 I believe)? > This got me to thinking, so I did a little poking around. /dev/hde exists, so I tried hdparm and it replied that the device wasn't configured. After giving it a little more thought, I tried insmod ide-disk, and everything fell into place. Oh what a difference a .o makes. Thanks to everyone for your patience and assistance! -- Steve ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
Re: Promise Ultra66
Michael McLeod wrote: > Stephen, > I tried the same thing from the mini and it didn't then I found instructions > at this web site: > http://www.linux.ucla.edu/pipermail/linux/2000-May/003326.html > Yes it is the numbers in [ ] which you add the 2 to. The mini is either > dead wrong or just very confusing. Well, I've done three things, one or a combination of which got me past the boot problem. (1) I made the changes to /etc/lilo.conf as you suggested. (2) I removed the initrd reference in /etc/lilo.conf as mentioned in my most recent post. (3) I compiled aic7xxx support into the kernel as opposed to loading it as a module. My reasoning, convoluted and poluted as it may be was that ATA-DMA support didn't have a module option and was being compiled directly into the kernel, so maybe the SCSI driver should be, too. I don't think this was necessarily sound reasoning, but after chasing this shadow for almost a week, I'd grown desperate in my attempts to catch it. So now, I'm past the kernel panic. Still, although dmesg indicates that /dev/hde exists, fdisk says it can't open /dev/hde. I'll be danged if I know why, either. All I can say at this point is that the speed improvement over ISA had damned well better be worth it . . . ;) -- Steve cat suggestions | grep solution > /dev/try_like_hell_to_make_it_work ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
Re: ppp changes hostname
fk wrote: > > Though ppp works fine, when I'm connected, it changes my local machine's > > hostname, i.e., when ppp isn't running the "hostname" command returns the > > correct hostname, but once ppp is running the "hostname" command returns > > the name of host I'm connected to. When I exit from ppp, the "hostname" > > command goes back to returning the correct name. > > linuxconf has an option to keep this from happening. I can't remember exactly where, but if you click through the screens, you're bound to find it. Hope this helps. -- Steve ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
Re: Promise Ultra66 FIXED (well, sort of . . .)
Okay, it finally occurred to me that my lilo.conf was wrong. Note: image=/boot/bzImage-ultra label=ultra initrd=/boot/initrd-2.2.17.img read-only root=/dev/sda1 append="pci=reverse ide2=0x78d0,0x78d3 ide3=0x78c4,0x78c7" This wasn't working because I was using the old initrd. By removing that line completely, the system came right up. Now I have yet another problem. dmesg contains the following regarding the drive: # dmesg | grep hd ide2: BM-DMA at 0x7880-0x7887, BIOS settings: hde:pio, hdf:pio ide4: BM-DMA at 0x7888-0x788f, BIOS settings: hdi:pio, hdj:pio hde: probing with STATUS(0x50) instead of ALTSTATUS(0x01) hde: WDC WD450AA-00BAA0, ATA DISK drive hdf: probing with STATUS(0x00) instead of ALTSTATUS(0x01) SCSI device sda: hdwr sector= 512 bytes. Sectors= 8388315 [4095 MB] [4.1 GB] SCSI device sdb: hdwr sector= 512 bytes. Sectors= 8515173 [4157 MB] [4.2 GB] hde: bad special flag: 0x03 So, /dev/hde is my new device. I don't know what the last line is referencing. But, # /sbin/fdisk /dev/hde Unable to open /dev/hde So, there's definitely something amiss. Following is all of what I believe to be the pertinent information. If I need to provide anything more, just say the word. My /proc/ide contains the following: # ls -al total 0 dr-xr-xr-x 3 root root0 Oct 10 16:46 . dr-xr-xr-x 52 root root0 Oct 10 11:30 .. -r--r--r-- 1 root root0 Oct 10 17:06 drivers lrwxrwxrwx 1 root root0 Oct 10 17:06 hde -> ide2/hde dr-xr-xr-x 3 root root0 Oct 10 17:06 ide2 -r--r--r-- 1 root root0 Oct 10 17:06 pdc202xx drivers is an empty file. pdc202xx contains: # cat pdc202xx PDC20262 Chipset. --- General Status - Burst Mode : enabled Host Mode: Normal Bus Clocking : 33 PCI Internal IO pad select: 4 mA Status Polling Period: 14 Interrupt Check Status Polling Delay : 1 --- Primary Channel Secondary Channel - enabled enabled 66 Clocking disabled disabled Mode MASTER Mode MASTER FIFO Empty FIFO Empty --- drive0 - drive1 drive0 -- drive1 -- DMA enabled:no no nono DMA Mode: UDMA 4 NOTSET NOTSET NOTSET PIO Mode: PIO 4NOTSET NOTSET NOTSET /proc/ide/ide2/hde contains the following information: # ls -al total 0 dr-xr-xr-x 2 root root0 Oct 10 17:08 . dr-xr-xr-x 3 root root0 Oct 10 17:08 .. -r--r--r-- 1 root root0 Oct 10 17:09 driver -r 1 root root0 Oct 10 17:09 identify -r--r--r-- 1 root root0 Oct 10 17:09 media -r--r--r-- 1 root root0 Oct 10 17:09 model -rw--- 1 root root0 Oct 10 17:09 settings The file media contains: disk The file model contains: WDC WD450AA-00BAA0, which is the correct identity of the drive connected to the board. Anybody have any ideas as to what I've screwed up now? Thanks! -- Steve ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
Re: Promise Ultra66
Michael McLeod wrote: > >I have just been working with an Ultra 66 and an upgrade of 6.0 to 6.2 and >based on what I have been doing your ide2=. and ide3=. are wrong. I >think they should be " ide2=0x78d0, 0x78d3 ide3=0x78c4, 0x78c7. Maybe >this will help. I don't understand this. According to the Ultra DMA HowTo, the formula is: RAID bus interface: Promise Technology Unknown device (rev 1). Vendor id=105a. Device id=4d33. Medium devsel. IRQ 12. Master Capable. Latency=32. I/O at 0xe000. (a) I/O at 0xd804. (b) I/O at 0xd400. (c) I/O at 0xd004. (d) I/O at 0xc800. (e) and pass "ide2=a,b+2 ide3=c,d+2" as a command line parameter to the kernel. My table is: Bus 0, device 10, function 0: Unknown mass storage controller: Promise Technology Unknown device (rev 1). Vendor id=105a. Device id=4d38. Medium devsel. IRQ 14. Master Capable. Latency=64. I/O at 0x78d0 [0x78d1]. I/O at 0x78c4 [0x78c5]. I/O at 0x78c8 [0x78c9]. I/O at 0x78c0 [0x78c1]. I/O at 0x7880 [0x7881]. Non-prefetchable 32 bit memory at 0xfebc [0xfebc]. So, following the formula: a = 0x78d0 b = 0x78c4 + 2 = 0x78c6 c = 0x78c8 d = 0x78c0 + 2 = 0x78c2 It appears to me that you've considered the bracketed numbers [0x78d1] as b and [0x78c5] as d. Don't misunderstand me. I'm not arguing and I'm certainly going to give your suggestion a go. I'm just trying to understand where I got it wrong. -- Steve ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
Re: Promise Ultra66
Jamin Collins wrote: > >Does the system have USB ports? If so, are they enabled/disabled? Also, >what video card are you using? I notice that the SCSI controller is >attempting to use 11. However, I've never really had much success with >using this IRQ as my systems have had other devices that wanted this IRQ >(video and USB normally). You might be getting away with using 11 because >14 and 15 are dormant under the other kernel (I'm speculating here). No USB ports. Video runs on IRQ 4 (which oddly enough doesn't show in /proc/interrupts). The SCSI device has never complained about being on IRQ 11, but just for kicks, I moved it to IRQ 3 with the same results I've been seeing for almost a week now. /proc/interrupts doesn't show it (because the only working kernel I have doesn't know about the Promise board so therefore doesn't see it), but IRQ 14 is where the Promise resides. /proc/pci shows it to be such. *sigh* -- Steve ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
Re: Promise Ultra66
Jamin Collins wrote: > > I know this has most likely been covered already. But, if you boot without > the IDE, what are the IO and IRQ address of the SCSI controller? The > behavior that you have listed is very similar to some conflicts I've seen > with Advansys cards and IO/IRQ problems. > /proc/interrupts: CPU0 CPU1 0: 569608 744300IO-APIC-edge timer 1: 1 1IO-APIC-edge keyboard 2: 0 0 XT-PIC cascade 8: 0 1IO-APIC-edge rtc 9: 27697 27605 IO-APIC-level DC21143 (eth0) 10: 21600 21925 IO-APIC-level eth1 11: 22779 24652 IO-APIC-level aic7xxx 13: 1 0 XT-PIC fpu NMI: 0 ERR: 0 /proc/ioports: -001f: dma1 0020-003f: pic1 0040-005f: timer 0060-006f: keyboard 0070-007f: rtc 0080-008f: dma page reg 00a0-00bf: pic2 00c0-00df: dma2 00f0-00ff: fpu 03c0-03df: vga+ 03f8-03ff: serial(auto) 7000-70ff: eth1 7400-74fe: aic7xxx 7800-787f: DC21143 (eth0) > -Original Message- > From: Stephen E. Hargrove [mailto:[EMAIL PROTECTED]] > Sent: Monday, October 09, 2000 10:44 AM > To: redhat-list > Subject: Promise Ultra66 > > Well, the fun just never ends with this new controller. This is a > somewhat lengthy email, so if you're not interested, just delete it now > and move on to brighter and shinier things. ;-) > > I've read and re-read the HOWTO on this, but I /cannot/ keep the system > from crashing. It doesn't seem to like the co-existence of my PCI SCSI > (from which I boot) and the Ultra66. Here's the applicable section of > my /proc/pci: > > Bus 0, device 10, function 0: > Unknown mass storage controller: Promise Technology Unknown device > (rev 1). > Vendor id=105a. Device id=4d38. > Medium devsel. IRQ 14. Master Capable. Latency=64. > I/O at 0x78d0 [0x78d1]. > I/O at 0x78c4 [0x78c5]. > I/O at 0x78c8 [0x78c9]. > I/O at 0x78c0 [0x78c1]. > I/O at 0x7880 [0x7881]. > Non-prefetchable 32 bit memory at 0xfebc [0xfebc]. > > Based on this information, following is my /etc/lilo.conf. The > label=linux kernel knows nothing about the Ultra66, and therefore boots > perfectly. The label=ultra is the problem child. The append statement > was added (pursuant to the HOWTO) based on the information in /proc/pci. > > boot=/dev/sda > map=/boot/map > install=/boot/boot.b > prompt > timeout=50 > default=linux > > image=/boot/bzImage > label=linux > initrd=/boot/initrd-2.2.17.img > read-only > root=/dev/sda1 > > image=/boot/bzImage-ultra > label=ultra > initrd=/boot/initrd-2.2.17.img > read-only > root=/dev/sda1 > append="ide2=0x78d0,0x78c6 ide3=0x78c8,0x78c2" > > I've tried pci=reverse. I've tried pci=nobios. I've tried hde=noprobe. > They all result in the following scenario. Much of what follows is a > recap of my prior post, as I want to be as complete as possible. And > just to be perfectly clear, the system BIOS is configured to boot from > the PCI SCSI controller. > > I'm running v2.2.17, and I've applied the proper patch from > http://www.kernel.org/pub/linux/kernel/people/hedrick/ide-2.2.17/ and > enabled the following in the config: > > Use DMA by default when available > ATA Work(s) In Progress > Promise PDC20246/PDC20262 support > Special UDMA Feature > Special Mode Feature > > (I don't know that I needed the ATA Work(s) option, but since there > wasn't any documentation available for it, I threw it in for good > measure.) The documentation for the Promise support option stated that > I /must/ have the first option (Use DMA by default . . .). > > Also, just for good measure, I've flashed the BIOS on the Ultra card to > the latest and greatest version. > > When I boot to the new kernel, everything SCSI goes south. Following > are some excerpts of the boot process. I've edited out some stuff that > is repeated multiple times, but if I cut something important, just let > me know and I'll send it: > > Uniform Multi-Platform E-IDE driver Revision: 6.30 > ide: Assuming 33MHz system bus speed for PIO modes; override with > idebus=xx > PDC2062: IDE controller on PCI bus 00 dev 50 > PDC2062: chipset revision 1 > PDC2062: not 100% native mode: will probe irqs later > PDC2062: (U)DMA Burst Bit ENABLED Primary PCI Mode Secondary PCI Mode. > PDC2062: FORCING PRIMARY MODE BIT 0x00 -> 0x01 MASTER > PDC2062: FORCING SECONDARY MODE BIT 0x00 -> 0x01 MASTER >ide2: BM-DMA at 0x78
Promise Ultra66
Well, the fun just never ends with this new controller. This is a somewhat lengthy email, so if you're not interested, just delete it now and move on to brighter and shinier things. ;-) I've read and re-read the HOWTO on this, but I /cannot/ keep the system from crashing. It doesn't seem to like the co-existence of my PCI SCSI (from which I boot) and the Ultra66. Here's the applicable section of my /proc/pci: Bus 0, device 10, function 0: Unknown mass storage controller: Promise Technology Unknown device (rev 1). Vendor id=105a. Device id=4d38. Medium devsel. IRQ 14. Master Capable. Latency=64. I/O at 0x78d0 [0x78d1]. I/O at 0x78c4 [0x78c5]. I/O at 0x78c8 [0x78c9]. I/O at 0x78c0 [0x78c1]. I/O at 0x7880 [0x7881]. Non-prefetchable 32 bit memory at 0xfebc [0xfebc]. Based on this information, following is my /etc/lilo.conf. The label=linux kernel knows nothing about the Ultra66, and therefore boots perfectly. The label=ultra is the problem child. The append statement was added (pursuant to the HOWTO) based on the information in /proc/pci. boot=/dev/sda map=/boot/map install=/boot/boot.b prompt timeout=50 default=linux image=/boot/bzImage label=linux initrd=/boot/initrd-2.2.17.img read-only root=/dev/sda1 image=/boot/bzImage-ultra label=ultra initrd=/boot/initrd-2.2.17.img read-only root=/dev/sda1 append="ide2=0x78d0,0x78c6 ide3=0x78c8,0x78c2" I've tried pci=reverse. I've tried pci=nobios. I've tried hde=noprobe. They all result in the following scenario. Much of what follows is a recap of my prior post, as I want to be as complete as possible. And just to be perfectly clear, the system BIOS is configured to boot from the PCI SCSI controller. I'm running v2.2.17, and I've applied the proper patch from http://www.kernel.org/pub/linux/kernel/people/hedrick/ide-2.2.17/ and enabled the following in the config: Use DMA by default when available ATA Work(s) In Progress Promise PDC20246/PDC20262 support Special UDMA Feature Special Mode Feature (I don't know that I needed the ATA Work(s) option, but since there wasn't any documentation available for it, I threw it in for good measure.) The documentation for the Promise support option stated that I /must/ have the first option (Use DMA by default . . .). Also, just for good measure, I've flashed the BIOS on the Ultra card to the latest and greatest version. When I boot to the new kernel, everything SCSI goes south. Following are some excerpts of the boot process. I've edited out some stuff that is repeated multiple times, but if I cut something important, just let me know and I'll send it: Uniform Multi-Platform E-IDE driver Revision: 6.30 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx PDC2062: IDE controller on PCI bus 00 dev 50 PDC2062: chipset revision 1 PDC2062: not 100% native mode: will probe irqs later PDC2062: (U)DMA Burst Bit ENABLED Primary PCI Mode Secondary PCI Mode. PDC2062: FORCING PRIMARY MODE BIT 0x00 -> 0x01 MASTER PDC2062: FORCING SECONDARY MODE BIT 0x00 -> 0x01 MASTER ide2: BM-DMA at 0x7880 - 0x7887, BIOS settings: hde: pio, hdf: pio ide3: BM-DMA at 0x7880 - 0x7887, BIOS settings: hde: pio, hdf: pio hde: WDC WD450AA-00BAA0, ATA Disk Drive ide2 at 0x78d0 - 0x78d7, 0x78c6 on irq 14 Then, it begins id'ing my SCSI devices. However, it identifies each device twice, such as: Detected SCSI disk sdb @ scsi0, channel 0, id 1, lun 0 Detected SCSI disk sdb @ scsi0, channel 0, id 2, lun 0 And then, when it hits my Plextor CD-RW, it goes nuts: Detected SCSI disk sdb @ scsi0, channel 0, id 3, lun 0 Detected SCSI disk sdb @ scsi0, channel 0, id 4, lun 0 Detected SCSI disk sdb @ scsi0, channel 0, id 5, lun 0 Detected SCSI disk sdb @ scsi0, channel 0, id 6, lun 0 Detected SCSI disk sdb @ scsi0, channel 0, id 7, lun 0 <*snip*> Detected SCSI disk sdb @ scsi0, channel 0, id 15, lun 0 sr1: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray sr2: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray sr3: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray sr4: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray sr5: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray sr6: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray sr7: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray sr8: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray sr9: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray sr10: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray <*snip*> SCSI disk error: host 0 channel 0 id 0 lun 0 return code=1802 sd08:01: old sense key None <*snip*> Non-extended sense class 0 code 0x0 scsidisk I/O error: dev 08:01, sector 190242 EXT2-FS error (device sd(8,1)): ext2_read_inode: unable to read inode block - inode=22617, block 90121 Kernel panic: no init found. Try passing init = option to kernel. I'm at
smbmount
Can anyone tell me what's wrong with the following command? # smbmount //peacedog/c /mnt/stephen -d 777 This command results in the following error message: mount error: Invalid argument Please look at smbmount's manual page for possible reasons I've looked at the man page for both smbmount and smbmnt and I can't see what I'm doing wrong. peacedog is a machine on my network, and c is a shared resource. I've verified this by (1) smbclient -L //peacedog and (2) connecting to the resource from Win9x machines. Thanks! -- Steve ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
Re: Fun with Ultra-DMA
Paul Anderson wrote: > This is strictly a guess...But when I have had this type of problem before > it was becuase both the IDE and the SCSI were trying to be the primary boot > device at the same time. In my case I was forced to let the IDE be the > primary boot device and shut the boot capcbility off on the SCSI device. I > was still able to "boot" from the SCSI devices using LILO. Hi Paul. Thanks for the response. What parameter should I pass to LILO in order to force the SCSI boot? (I'm away from my primary computer right now, and therefore without my bookmarks and normal resources.) Thanks! -- Steve ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
Fun with Ultra-DMA
Well, I'm just having a blast trying to get my Promise Ultra66 operational. (Translation: #$&%!!#&*^%!!) Here's the setup: I have an embedded PCI SCSI, which works perfectly. The BIOS is set up to boot off this device. I've added a Promise Ultra66 in one of the PCI slots, and the system BIOS properly recognizes it and the hard drive attached to it. I've downloaded the patch at http://www.kernel.org/pub/linux/kernel/people/hedrick/ide-2.2.17/ (since I'm running version 2.2.17), patched the kernel and enabled the following in the config: Use DMA by default when available ATA Work(s) In Progress Promise PDC20246/PDC20262 support Special UDMA Feature Special Mode Feature (I don't know that I needed the ATA Work(s) option, but since there wasn't any documentation available for it, I threw it in for good measure.) The documentation for the Promise support option stated that I /must/ have the first option (Use DMA by default . . .). Also, just for good measure, I've flashed the BIOS on the Ultra card to the latest and greatest version. When I boot to the new kernel, everything SCSI goes south. Following are some excerpts of the boot process. I've edited out some stuff that is repeated multiple times, but if I cut something important, just let me know and I'll send it: Uniform Multi-Platform E-IDE driver Revision: 6.30 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx PDC2062: IDE controller on PCI bus 00 dev 50 PDC2062: chipset revision 1 PDC2062: not 100% native mode: will probe irqs later PDC2062: (U)DMA Burst Bit ENABLED Primary PCI Mode Secondary PCI Mode. PDC2062: FORCING PRIMARY MODE BIT 0x00 -> 0x01 MASTER PDC2062: FORCING SECONDARY MODE BIT 0x00 -> 0x01 MASTER ide2: BM-DMA at 0x7880 - 0x7887, BIOS settings: hde: pio, hdf: pio ide3: BM-DMA at 0x7880 - 0x7887, BIOS settings: hde: pio, hdf: pio hde: WDC WD450AA-00BAA0, ATA Disk Drive ide2 at 0x78d0 - 0x78d7, 0x78c6 on irq 14 Then, it begins id'ing my SCSI devices. However, it identifies each device twice, such as: Detected SCSI disk sdb @ scsi0, channel 0, id 1, lun 0 Detected SCSI disk sdb @ scsi0, channel 0, id 2, lun 0 And then, when it hits my Plextor CD-RW, it goes nuts: Detected SCSI disk sdb @ scsi0, channel 0, id 3, lun 0 Detected SCSI disk sdb @ scsi0, channel 0, id 4, lun 0 Detected SCSI disk sdb @ scsi0, channel 0, id 5, lun 0 Detected SCSI disk sdb @ scsi0, channel 0, id 6, lun 0 Detected SCSI disk sdb @ scsi0, channel 0, id 7, lun 0 <*snip*> Detected SCSI disk sdb @ scsi0, channel 0, id 15, lun 0 sr1: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray sr2: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray sr3: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray sr4: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray sr5: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray sr6: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray sr7: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray sr8: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray sr9: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray sr10: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray <*snip*> SCSI disk error: host 0 channel 0 id 0 lun 0 return code=1802 sd08:01: old sense key None <*snip*> Non-extended sense class 0 code 0x0 scsidisk I/O error: dev 08:01, sector 190242 EXT2-FS error (device sd(8,1)): ext2_read_inode: unable to read inode block - inode=22617, block 90121 Kernel panic: no init found. Try passing init = option to kernel. There's /got/ to be some conflict between the Ultra-patched drivers and the SCSI devices. When I boot with the older kernel, the SCSI drives work fine. /etc/lilo.conf is set up to boot from /dev/sda1. Anybody have any thoughts as to where I should begin looking or what I may have screwed up? Thanks! -- Steve ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
Re: unsubscribe -can someone at least bother to reply 4 the first time
[EMAIL PROTECTED] said: > sod (sd) Chiefly British > n. > 1. >a.A sodomite. # man sod No manual entry for sod hrm . . . according to Linux, this definition can't be correct. ;-) -- Steve ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
Conferencing?
What's everyone using for Internet conferencing? I've got several machines masqueraded and behind a firewall. Boss man wants to use NetMeeting, but from my reading of Section 6 of the IP Masq HOWTO, H.323 programs (such as NetMeeting) are currently out of the question. Basically, I need video, audio and filesharing capabilities, and I need to get it set up pretty quick. Any suggestions? Thanks! -- Steve ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
Re: PCI Problems
"Mikkel L. Ellertson" wrote: > Steve, > I cann't help with this problem, but I thought I should warn you > about one problem you will probably run into when you get this working. > If you are going to keep booting from the SCSI drives, then you are going > to have to add a couple of lines to /etc/lilo.conf so LILO know what > drive is the first drive your BIOS sees. > > disk=/dev/sda > bios=0x80 thanks for the info, mikkel, but the system is booting from the scsi drives with no problem (right now). once i get the system to recognize the pci board though, this could become an issue. i'll keep an eye on it. thanks again. -- Steve ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
PCI Problems
I just installed a new PCI IDE board in my machine. It's a PCI ATA/IDE 66. The machine is completely SCSI, so this is the first IDE drive to be installed in the box. At bootup, the BIOS recognizes it as a PCI board and spits out the correct messages identifying the harddrive that is attached to it. Linux is having problems correctly identifying the board, though. The first time through, kudzu identified it as a RAID device. I modified /etc/sysconfig/hwconfig and removed the entry. On the next boot, kudzu again identified it as a RAID device, so I told it to ignore it and not add it to the hardware configuration. My /proc/pci contains the following entry, which I believe pertains to the card as I've never seen it before: Bus 0, device 10, function 0: RAID storage controller: CMD Unknown device (rev 1). Vendor id=1095. Device id=648 Medium devsel. Fast back-to-back capable. IRQ 9. Master Capable. Latency=64. Min Gnt=2.Max Lat=4. I/O at 0x7c20 [0x7c21]. I/O at 0x7c14 [0x7c15]. I/O at 0x7c18 [0x7c19]. I/O at 0x7c10 [0x7c11]. My /proc/interrupts also has a weird entry. Here's the last few lines: 14: 4218 4130IO-APIC-level aic7xxx NMI: 0 ERR: 0 I've never noticed the ERR: line before (although it could be normal, just that I've never noticed it before). I've compiled the kernel with PCI disk support as a module, and the insmod command works fine. However, when I attempt to access /dev/hda1, I get the following: mount: the kernel does not recognize /dev/hda1 as a block device (maybe 'insmod driver'?) Naturally, /dev/hda1 isn't being recognized because the system isn't seeing my IDE card correctly. Does anyone have any advice on how I should proceed from here? If I need to provide further info, just say the word. Thanks! -- Steve ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
Re: Kernel Panic FIXED
thanks for everyone's assistance. it was indeed the system map and initrd image. thanks again! -- Steve ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
Re: Kernel Panic
Statux wrote: > aic.. is that something to do with SCSI? if so.. block-major-8 is the SCSI > disk devices ("ls -l /dev | grep 8,"). don't have support for the SCSI > stuff.. you aren't going to be able to mount anything. Do you have the > initrd (initial ramdisk) support enabled? I understand that SCSI systems > need it so the related modules get installed correctly... yeah, aic7xxx.o is the module for my scsi board. like i said, if i boot to the old kernel (2.2.12-20), it works fine. it's booting to the new kernel that's giving me fits. for some reason, the system seeks to be trying to load the old aic7xxx.o (i.e., 2.2.12-20) rather than the one compiled with 2.2.17. > do you have the option about setting version info on all modules (near the > beginning of the config) enabled? (NOTE: in kernel 2.4.x, if you use ppp > and want it to be compiled into the kernel, you cannot use the version > info thingie.. dunno why they did that tho) yes, i do. -- Stephen E. Hargrove Attorney at Law http://www.StephenHargrove.com * Mozart: http://mozart.sourceforge.net Texas Criminal Law: http://www.virtual-attorney.com/criminal Linux & The Law Office: http://www.virtual-attorney.com/linux BuckOwensFan.com: http://www.BuckOwensFan.com * ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
Kernel Panic
I'm testing v2.2.17, and have run into a problem. While the kernel is booting, I get the following error: Loading aic7xxx module /lib/aic7xxx.o: Kernel-module version mismatch /lib/aic7xxx.o was compiled for kernel version 2.2.12-20smp while this kernel is version 2.2.17. kmod: failed to exec /sbin/modprobe -s -k block-major-8, errno=2 VFS: cannot open root device 08:01 Kernel panic: VFS: unable to mount root fs on 08:01 Obviously, I'm upgrading from 2.2.12. Following are the steps I took: tar xfvz linux-2.2.17 cd linux make config make dep make clean make bzImage make modules make modules_install Everything /seems/ to have gone off without a hitch. All of the modules installed in /lib/modules/2.2.17 correctly. The following directories now exists in /lib/modules: 2.2.12-20 2.2.12-20smp 2.2.17 For whatever reason, aix7xxx doesn't seem to be recompiling or the incorrect version is being installed. I always assumed that when booting a kernel (such as 2.2.17), it would look to the 2.2.17 modules library. But for some reason (again, I'm assuming here - dangerous stuff), the system seems to be trying to pull the aic7xxx from the 2.2.12-20smp modules directory. Does anyone have an idea as to where I need to go from here? What am I missing? Thanks! -- Steve ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
Re: make dep problems
"Stephen E. Hargrove" wrote: > > i'm trying to recompile my kernel (2.2.16). I've been running > 2.2.12smp, which was installed by default by RH during my 6.1 > installation. I've make several recompiles in the past on 2.2.12, but > I've just run into a problem I've never encountered. Nevermind. I figured it out. I'm an idiot. Thanks. -- Steve ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
make dep problems
i'm trying to recompile my kernel (2.2.16). I've been running 2.2.12smp, which was installed by default by RH during my 6.1 installation. I've make several recompiles in the past on 2.2.12, but I've just run into a problem I've never encountered. When testing the 2.2.16 kernel, it died on a kernel panic. After tweaking with the .config for a while, I decided to do a fresh install of 2.2.16. So, I did the following: tar xfvz linux-2.2.16.tar.gz mv linux linux-2.2.16 ln -s linux-2.2.16 linux I then copied my old .config into the new tree and did a make xconfig. After deciding everything looked okay, I entered make dep with the following results: make[1]: Entering directory `/usr/src/linux-2.2.16/arch/i386/boot' make[1]: Nothing to be done for `dep'. make[1]: Leaving directory `/usr/src/linux-2.2.16/arch/i386/boot' scripts/mkdep init/*.c > .depend scripts/mkdep `find /usr/src/linux-2.2.16/include/asm /usr/src/linux-2.2.16/include/linux /usr/src/linux-2.2.16/include/scsi /usr/src/linux-2.2.16/include/net -follow -name \*.h ! -name modversions.h -print` > .hdepend find: /usr/src/linux-2.2.16/include/asm: No such file or directory make _sfdep_kernel _sfdep_drivers _sfdep_mm _sfdep_fs _sfdep_net _sfdep_ipc _sfdep_lib _sfdep_arch/i386/kernel _sfdep_arch/i386/mm _sfdep_arch/i386/lib _sfdep_arch/i386/math-emu _FASTDEP_ALL_SUB_DIRS="kernel drivers mm fs net ipc lib arch/i386/kernel arch/i386/mm arch/i386/lib arch/i386/math-emu" make[1]: Entering directory `/usr/src/linux-2.2.16' make -C kernel fastdep make[2]: Entering directory `/usr/src/linux-2.2.16/kernel' make[2]: *** No rule to make target `/usr/src/linux-2.2.16/include/linux/autoconf.h', needed by `/usr/src/linux-2.2.16/include/linux/modules/signal.ver'. Stop. make[2]: Leaving directory `/usr/src/linux-2.2.16/kernel' make[1]: *** [_sfdep_kernel] Error 2 make[1]: Leaving directory `/usr/src/linux-2.2.16' make: *** [dep-files] Error 2 --- I checked, and sure enough, autoconf.h doesn't exist. What's up with that? Any advice would be greatly appreciated, as I need to get this machine operational withe new kernel PDQ. Thanks! -- Steve ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
Partitions
I'm preparing to install an IDE 45gb hard drive on a RH6.1 system. It's not a primary drive, and will mainly be used for extra storage of documents. I have a few elementary questions: 1) Other than making sure IDE support is compiled into the kernel, what steps do I need to take to prepare for installing this device? 2) What steps are necessary to get it properly formatted for Linux? 3) Would it be okay to devote the entire 45gb to one partition, or will it be necessary to divide it into numerous partitions? If I need to create more than one partition, how big should they be? 4) Also, I have a 4.5gb SCSI drive which currently mounts as /data on /dev/sdb1. Once I get the 45gb drive installed, all of the data on /data will be moved to the new drive, leaving /dev/sdb1 unoccupied. How do I go about (a) deleting the partition and (b) redefining it as /www? Basically, I'm wanting to move all webserver-related files to this one drive. Thanks! -- Steve ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
Re: kernel configuration
Erik de Groot wrote: > > Quick little question. > > I am running RH 6.1 and seem to have changed my kernel config file and can't find >the config > for my current kernel. > > Is there a way to get the configuration from the current running kernel? cd /usr/src/linux make oldconfig -- Steve ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
Securing FTP/Telnet
I've turned off FTP and Telnet access to my linux server by commenting out the following lines in inetd.conf: # ftp stream tcp nowait root/usr/sbin/tcpd in.ftpd -l -a # ftp stream tcp nowait root/usr/bin/ftpd -L -a # telnetstream tcp nowait root/usr/sbin/tcpd in.telnetd Also, I've set up my box to only allow certain IP addresses to telnet or FTP by adding the following to my hosts.allow: in.telnetd:192.168.2.2, 192.168.2.3, 192.168.2.6 and hosts.deny: in.telnetd:ALL So, the way the system is currently set up, only 3 machines on the internal network can telnet or FTP to the server. Telnet and FTP have been disabled, but ssh connections are currently working. I now have external users who need to access FTP and telnet services on the server (i.e., people from various locations with dynamic IP addresses). I need to ensure that both telnet and FTP are done only through ssh2. Is there a document that will walk me through implementing this, or can anyone give me a quick run through of what I need to do? Thanks! -- Steve ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
Re: Port Forwarding Maybe? SOLVED
That's the ticket! Thank Michael. I modified httpd.conf to listen to 192.168.1.10:80 and pointed the pinhole on the DSL router to 192.168.1.10 and now is working perfectly. Thanks again! -- Steve ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
Re: Port Forwarding Maybe?
Sorry for the confusing info in my original post. Let my try to clarify based on the questions received. "Michael R. Jinks" wrote: > > Does the DSL modem have two associated IP's as well -- 192.168.1.254 and > also the 66.x.x.x address you mention below? 192.168.1.254 is the internal IP address of the DSL modem. 66.x.x.x is the IP address assigned to the connection between my ISP and the DSL modem. > Are the "internal network" and "connects to DSL" addresses above both residing > on one system? (that's what I assume but you don't say explicitly) Yes. > So in English, you're forwarding 66.x.x.x:80 on the Cayman to either > 192.168.2.1:80 or 192.168.1.10:80 on your internal system? Yes. > About the internal system -- does it pass those packets on to some other > machine, or does it house the web daemon itself? At this point I'm a little > confused about your network topology. The machine has two NICs: 192.168.1.10 connects to the DSL modem. 192.168.2.1 connects to the internal network. This machine houses the the web daemon. > The "outside network" in this sentence is The Internet? Or a DMZ between > your "home" network and the outside? Yes. Any connection made from outside my internal network, i.e., someone trying to access Apache from the Internet. > How are 192.168.1.0 and 192.168.2.0 connected? I don't understand this question. > > > I'm specifically requesting > > http://66.xxx.xxx.xxx/index.html, which does exist. > > > > - If I configure Apache to listen to 192.168.1.10:80, the system responds > > that the website is unreachable. > > Which system? That's the response received when trying to access the webserver from the Internet (i.e., from outside the internal network - from home, another office, etc.). > > I'm using IP Masquerade to mask all traffic on the internal network out > > through 192.168.1.10 and the router. > > _and_ the router? Please explain what that means. Internal requests for external resources route out 192.168.1.10, which is connected to the DSL router, which is connected to the Internet. > Which network -- 192.168.2.0 or 192.168.1.0 -- do you mean by the "internal" > network? 192.168.2.0 is the internal network. 192.168.1.0 houses the NIC connecting to the DSL router (192.168.1.10) and the DSL router (192.168.1.254). > I think what would help me the most is if you could describe your network > layout a little more -- specifically, where does the web server live, how many > machines are actually involved, and which network addresses reside where? 192.168.2.1 is a NIC on the server. 192.168.2.2 is a workstation. 192.168.2.6 is a workstation. etc. 192.168.1.10 is a NIC on the same server previously mentioned. 192.168.1.254 is the DSL router. The router connects to 192.168.1.10 and the Internet. 192.168.2.2---|---||--| 192.168.2.6---|Server |192.168.1.10| DSL router | 66.x.x.x 192.168.2.8---|192.168.2.1|eth1| 192.168.1.254|- Internet 192.168.2.9---|___eth0||__| I hope this helps. If I can provide further info, please let me know. -- Steve ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
Port Forwarding Maybe?
I've been chasing a problem now for a few days, and it's driving me nuts. Hopefully someone here can shed some light on my obviously darkened (at best) understanding. Two NICs: 192.168.2.1 - internal network 192.168.1.10 - connects to DSL router 192.168.1.254 - DSL router/Modem I'm trying to let the external world access an internal webserver. On the DSL router (Cayman 3220-H), I've created a pinhole for incoming requests to port 80. Following are the scenarios: - If I point the pinhole to 192.168.2.1, attempting to access my webserver from outside the network results in a timeout. - If I point the pinhold to 192.168.1.10 and use ipmasqadm portfw -a -P tcp -L 192.168.1.10 80 -R 192.168.2.1 80, the system responds that the page contains no data. I'm specifically requesting http://66.xxx.xxx.xxx/index.html, which does exist. - If I configure Apache to listen to 192.168.1.10:80, the system responds that the website is unreachable. I'm using IP Masquerade to mask all traffic on the internal network out through 192.168.1.10 and the router. Can anyone offer me any advice on how to make my internal webserver available to the external world? Thanks in advance, and if you need more information, just say the word! -- Steve ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
just a test
test ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
Mount problems
I'm trying to mount a shared directory on a Win98 system using the following command: smbmount //peacedog/g /mnt/stephen -d 777 The system responds with the following message: SMBFS: need mount version 6 mount error: Invalid argument Please look at smbmount's manual page for possible reasons Does anyone know where I can find mount version 6 (or which package to download)? I've poked around various places and haven't been able to locate it. Thanks! -- Steve ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
Pinholes, Port 80 and other nonsense
The basic problem is that when I try to access my http server, I receive the following message: Network error Unable to request URL from host 63.101.116.77:80: Connection refused The background is a little convoluted, so if I leave anything out, just let me know and I'll be glad to supplement. 192.168.2.1 is my Linux box. It's running httpd on port 80. A netstat -an | grep LISTEN | grep 80 reveals that http is listening to port 80. This machine masquerades at 192.168.2.0, forwarding external requests to 192.168.1.10, which is a network card connected to a Cayman DSL modem/router/firewall defined as 192.168.1.254. Querying the Cayman reveals the following IP information: IP Interfaces: ENET (lan): ( up broadcast default rip-send v1 rip-receive v1 ) inet 192.168.1.254 netmask 255.255.255.0 broadcast 192.168.1.255 physical address 00.00.89.2a.e6.8a mtu 1500 PPP (vcc1): ( up point-to-point address-mapping ) inet 63.101.116.77 netmask 0.0.0.0 peer address 207.18.66.1 physical address 00.00.00.00.00.00 mtu 1500 I'm working on the assumption that 63.101.116.77 is the dynamic IP address assigned by my ISP. On the Cayman, I've defined a "pinhole" as follows: Protocol: TCP External Port: 80 Internal Port: 80 Internal IP Address: 192.168.2.1 According to the documentation, this should pass TCP requests for port 80 to the internal IP address of 192.168.2.1. Judging from the error message, it appears to be working. Internally, if I access http://192.168.2.1, everything works properly. Apache serves up the webpages. However, when I access http://63.101.116.77, I get the error message given above. Does anyone have any idea as to why this connection is being refused? Do I need to give some sort of ipchains command that will allow the request to pass through to 192.168.2.1? If so, what would that be? Again, if I need to provide more information, just say the word. Thanks! -- Steve ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
Re: DSL & Dual NICs
A big "thank you" to everyone who participated in this thread. My network is now functional! -- Steve ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
DSL (SOL/DOA)
Okay, I've taken everyone's recommendations to heart concerning eth0, eth1 and my private network. I can access all machines locally, but IP Masquerade isn't working (i.e., I can't ping outside of 192.168.2.0 UNLESS I'm working from 192.168.2.1, in which case I can access both the private network and the Internet). I've set up the following: eth0: 192.168.2.1 eth1: 192.168.1.10 192.168.2.x is now my private network. 192.168.1.x relates to the outside world. eth1 is set to 192.168.1.10 because it connects to my DSL modem/router which is set to 192.168.1.254. Following is my netstat -rn: Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 192.168.2.1 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 192.168.1.100.0.0.0 255.255.255.255 UH 0 0 0 eth1 192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo 0.0.0.0 192.168.1.254 0.0.0.0 UG 0 0 0 eth1 I execute the following in my rc.local during boot-up (this is necessary because the tulip driver conflicts with the eth0 driver if they're both activated during boot-up): insmod /lib/modules/2.2.12-20/net/tulip.o /etc/sysconfig/network-scripts/ifup eth1 route add default gw 192.168.1.254 eth1 /etc/rc.d/rc.dsl /etc/rc.d/rc.dsl contains my ipchains commands for setting up IP Masquerade. In addition to the normal IP Masq commands (/sbin/depmod -a, /sbin/modprobe ip_masq_ftp, etc.), the following is executed: /sbin/ipchains -P forward DENY /sbin/ipchains -A forward -s 192.168.1.10/24 -j MASQ /proc/sys/net/ipv4/ip_forward is set to 1 /proc/sys/net/ipv4/ip_dynaddr is set to 1 The default gateway on all machines within the 192.168.2.x network is set to 192.168.2.1. For example, here's the netstat on one of the machines: Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 192.168.2.6 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 192.168.2.0 0.0.0.0 255.255.255.0 U0 0 0 eth0 192.168.2.0 0.0.0.0 255.255.255.0 U0 0 0 eth0 127.0.0.0 0.0.0.0 255.0.0.0 U0 0 0 lo 0.0.0.0192.168.2.10.0.0.0 UG 0 0 0 eth0 All Win9x machines point to 192.168.2.1 as well. I've run a traceroute to an external address, and here's the result: # traceroute 208.221.108.11 traceroute to 208.221.108.11 (208.221.108.11), 30 hops max, 38 byte packets 1 pappy (192.168.2.1) 0.588 ms 0.431 ms 0.422 ms 2 * * * 3 * * * 4 * * * etc., etc., etc. It appears that 192.168.2.1 isn't routing the packets to 192.168.1.10. Again, from the machine defined as 192.168.2.1, I can access the private network and the world. But from any other machine, I can only access the 192.168.2.x network. I'm sure the fix is something simple, but right now, it's beyond me. Anyone have any ideas? Thanks. -- Steve ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
DSL & Dual NICs
My server has two NICs, eth0 (192.168.1.1) and eth1 (192.168.1.10). eth0 connects to my private network and eth1 connects to the external DSL modem (Cayman 3220 DSL router). The router acts as a firewall (which I hate but really can't do anything about). The router is defined as 192.168.1.254, and has 4 ethernet connections on the front. If I plug directly into the router, I can access http://192.168.1.254 from my browser and configure it. However, I can't access it from any station on my network (i.e., from 192.168.1.1 or 192.168.1.6, etc.). When I attempt, it responds with the following error: A network error occurred: unable to connect to server (TCP Error: No route to host) The server may be down or unreachable I can't ping it or telnet to it, either. So, I must have something wrong in my routing tables, right? Here's my netstat -rn: Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 192.168.1.1 0.0.0.0 255.255.255.255 UH0 0 0 eth0 192.168.1.100.0.0.0 255.255.255.255 UH0 0 0 eth1 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo 0.0.0.0 192.168.1.254 0.0.0.0 UG0 0 0 eth1 0.0.0.0 192.168.1.254 0.0.0.0 UG0 0 0 eth0 I'm using IPMasquerade, and as far as that goes, everything seems to be working correctly (all PCs can access the 'net, etc.). Does anyone have any ideas on how I can go about accessing 192.168.1.254? I'm stumped. -- Steve ___ Redhat-list mailing list [EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
test
just a test. sorry. -- To unsubscribe: mail [EMAIL PROTECTED] with "unsubscribe" as the Subject.
Route Problem
well, it's more a nuisance than a problem. following is my netstat -rn: Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 192.168.1.1 0.0.0.0 255.255.255.255 UH0 0 0 eth0 192.168.1.100.0.0.0 255.255.255.255 UH0 0 0 eth1 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo 0.0.0.0 192.168.1.254 0.0.0.0 UG0 0 0 eth1 0.0.0.0 192.168.1.100.0.0.0 UG0 0 0 eth0 as you can see, i'm the proud owner of two default gateways. i've tried to delete the 192.168.1.10 gateway, but apparently i'm too dense to properly structure the route del command. the man page isn't very helpful, and all of the books i have only discuss adding to the route table. anybody have an idea? -- Steve http://www.StephenHargrove.com * Mozart: http://www.virtual-attorney.com/mozart Linux & The Law Office: http://www.Virtual-Attorney.com/linux Texas Criminal Law: http://www.Virtual-Attorney.com/criminal BuckOwensFan: http://www.BuckOwensFan.com * -- To unsubscribe: mail [EMAIL PROTECTED] with "unsubscribe" as the Subject.
Re: ICQ
Ray Parish wrote: > > What ICQ program does this list suggest for Linux? Thanks i use everybuddy (www.everybuddy.com). i don't know about the other programs, but everybuddy lets you chat regardless of whether the other person uses aim, icq, msn or yahoo. -- steve -- To unsubscribe: mail [EMAIL PROTECTED] with "unsubscribe" as the Subject.
Re: Is WP8 for linux free dowload still available?
Lyndon Sundmark wrote: > > Does anyone know whether Corel's Wordperfect for Linux is still > available as a free download and if so where? > > I have gone to the usual sites: Corel, CDROM, and Download.com but to no > avail. ( ie the download links do not work) http://linux.corel.com -- steve -- To unsubscribe: mail [EMAIL PROTECTED] with "unsubscribe" as the Subject.
WP Office 2000
The original press release from Corel stated that Office 2000 would be available for download to currently registered users on March 27. I've looked on their website and can't find anything about a download. The only thing that mentions anything about a download is "WordPerfect Office 2000 for Linux will be available online and on store shelves in early April 2000." Does anyone know anything about what's up? -- Steve -- To unsubscribe: mail [EMAIL PROTECTED] with "unsubscribe" as the Subject.
Re: Tape Drive Woes
Adam Sleight wrote: > have you tried > tar cvfM /dev/st0 /whatever/directory; mt -f /dev/st0 rewoff Here's what I get: [root@linux Stephen]# tar cvfM /dev/st0 /home; mt -f /dev/st0 rewoff tar: Removing leading `/' from archive names home/ home/lost+found/ home/ftp/ home/ftp/bin/ home/ftp/bin/compress tar: WARNING: Cannot close /dev/st0 (3, -1): Input/output error Prepare volume #2 for /dev/st0 and hit return: when I hit ctl-c to break out: /dev/st0: Input/output error > instead of /dev/st0 you may need to use /dev/nst0 /dev/nst0 gives the same input/output error message that /dev/st0 gives. -- steve -- To unsubscribe: mail [EMAIL PROTECTED] with "unsubscribe" as the Subject.
Re: Tape Drive Woes
Bigdog wrote: > > Have you tried some of the simple commands to check that the drive > itself is OK, such as: > > mt -f /dev/st0 status > Here's the feedback I'm getting. It's all the same, and quite immediate. [root@linux Stephen]# mt -f /dev/st0 rewind /dev/st0: Input/output error [root@linux Stephen]# mt -f /dev/st0 retension /dev/st0: Input/output error [root@linux Stephen]# mt -f /dev/st0 erase /dev/st0: Input/output error [root@linux Stephen]# mt -f /dev/st0 tell /dev/st0: Input/output error [root@linux Stephen]# mt -f /dev/st0 load /dev/st0: Input/output error -- steve -- To unsubscribe: mail [EMAIL PROTECTED] with "unsubscribe" as the Subject.
Re: Tape Drive Woes
Hidong Kim wrote: > > Have you tried just regular tar? > > tar cvf /some/directory /dev/st0 /dev/st0 is nonresponsive. The tape whirs during boot-up and dmesg lists the drive as mentioned before. Other than this, nothing. > Also, check the permissions on /dev/st0 to see if your user is allowed > to access it. Good luck, I'm running as root. Here's the ls -al: crw-rw 1 root disk 9, 0 May 5 1998 /dev/st0 -- steve -- To unsubscribe: mail [EMAIL PROTECTED] with "unsubscribe" as the Subject.
Re: OT: ntop
Alan Mead wrote: > > Any port? Are you running it as root? 100 is a privileged port. I would > try something > 1000. But I think you must still be root to run it. i'm running it as root. i've tried various ports (e.g., 1000, 1050, 3000, 1024, etc.) all with the same results: Network error Unable to read URL from host 192.168.1.1: no response from server -- steve -- To unsubscribe: mail [EMAIL PROTECTED] with "unsubscribe" as the Subject.
Re: OT: ntop
Hal Burgiss wrote: > > Mine is: > > [hal@feenix hal]$ ll /sbin/ntop > -rwsr-xr-x 1 root sys255928 May 3 1999 /sbin/ntop* > > I installed via RPM, so this probably whoever did the spec file. Since > it needs to go into promiscuous mode (AFAIK), it may need to be > owned by root also. well, i did a chmod 6755 on it such that it appeared as: -rwsr-sr-x 1 Stephen users 746388 Mar 21 10:17 /usr/local/sbin/ntop and chmod 755 so it is: -rwxr-xr-x 1 Stephen users 746388 Mar 21 10:17 /usr/local/sbin/ntop but the result is still the same. i also get the same results when owner/group is root, so that can't be it either. -- steve -- To unsubscribe: mail [EMAIL PROTECTED] with "unsubscribe" as the Subject.
Re: NeoMagic Chip
Jay Guerette wrote: > Do you have enough memory to support that color depth at that resolution? > > --- > Jay Guerette > Operations Group > Raging Bull, Inc. > 100 Brickstone Square > Andover, MA 01810 > 978-247-5554 I think this is it. At 2mb, and given that everything else looks correct, it's the only explanation. Since there's no other place around the place, this must be the place. Thanks, guys. Now to see about getting this ram upgraded . . . -- Steve -- To unsubscribe: mail [EMAIL PROTECTED] with "unsubscribe" as the Subject.
NeoMagic Chip
I'm running Linux on a Gateway Solo 2500, and I've installed the patch at ftp://ftp.redhat.com/pub/XFCom/XFCom-neomagic-libc5-2.0.0-1.i386.rpm, but I cannot seem to get startx -- -bpp 24 working at 1024x768. Is this possible. Attached is my XF86Config file. Sorry to send attachments to the list, and thanks for any input you guys may have. -- Steve Section "Files" RgbPath "/usr/X11R6/lib/X11/rgb" FontPath "/usr/X11R6/lib/X11/fonts/misc/" FontPath "/usr/X11R6/lib/X11/fonts/75dpi/:unscaled" FontPath "/usr/X11R6/lib/X11/fonts/100dpi/:unscaled" FontPath "/usr/X11R6/lib/X11/fonts/Type1/" FontPath "/usr/X11R6/lib/X11/fonts/Speedo/" FontPath "/usr/X11R6/lib/X11/fonts/75dpi/" FontPath "/usr/X11R6/lib/X11/fonts/100dpi/" #ModulePath "/usr/X11R6/lib/modules" EndSection #Section "Module" #Load "xf86Jstk.so" #EndSection Section "ServerFlags" #NoTrapSignals #DontZap #DontZoom #DisableVidModeExtension #AllowNonLocalXvidtune #DisableModInDev #AllowNonLocalModInDev EndSection Section "Keyboard" Protocol"Standard" AutoRepeat 500 5 #XkbDisable XkbKeymap "xfree86(us)" EndSection Section "Pointer" #Protocol"Microsoft" #Device "/dev/ttyS0" Protocol"PS/2" Device "/dev/psaux" Emulate3Buttons Emulate3Timeout50 EndSection Section "Monitor" Identifier "Generic Multisync" VendorName "Unknown" ModelName "Unknown" HorizSync 30-64 VertRefresh 50-100 # 640x480 @ 60 Hz, 31.5 kHz hsync Modeline "640x480" 25.175 640 664 760 800 480 491 493 525 # 800x600 @ 60 Hz, 37.8 kHz hsync Modeline "800x600" 40 800 840 968 1056 600 601 605 628 +hsync +vsync # 1024x768 @ 60 Hz, 48.4 kHz hsync Modeline "1024x768"651024 1032 1176 1344 768 771 777 806 -hsync -vsync EndSection Section "Device" Identifier "NeoMagic" #Chipset"NM2160" #IOBase 0xfea0 #MemBase0xfd00 #VideoRam 2048 #DacSpeed 90 #Option "linear" #Option "nolinear" #Option "sw_cursor" #Option "hw_cursor" #Option "no_accel" #Option "intern_disp" #Option "extern_disp" #Option "mmio" #Option "no_mmio" #Option "lcd_center" #Option "no_stretch" EndSection Section "Screen" Driver "svga" Device "NeoMagic" Monitor "Generic Multisync" Subsection "Display" Depth 8 Modes "1024x768" "800x600" "640x480" EndSubsection Subsection "Display" Depth 16 Modes "1024x768" "800x600" "640x480" EndSubsection Subsection "Display" Depth 24 Modes "1024x768" "800x600" "640x480" EndSubsection EndSection