[speedtouch] Re: Installing Speedtouch 330 USB modem for portugal SAPO at Ubuntu Edgy Eft
Hi! I had a speedtouch working with ubuntu edgy (and in Portugal too) until recently, when I got a Sagem 1200 router off ebay. The speedtouch works fine, even though the sagem seems to allow faster throughput. What I did was basically what you have on the howtos you linked, you might want to try executing the instructions in the script by hand first just to check if it might be a timing problem. On Fri, 19 Jan 2007 16:41:35 +, Joao S. Carvalho wrote Hi there! I runned the command as Gilles suggested ( grep CONFIG_ATM_BR2684 /boot/config* ) and this is what i got: CONFIG_ATM_BR2684=m # CONFIG_ATMBR2684_IPFILTER is not set What does it means? What do you suggest me to do now? I also considered the problem might me that i have an AMD64 processor and not an intel but i installed the ubuntu 6.10 for intel anyway. But all the systems seems to be working properly so i think that shouldn't be interfering.. right? Installing a modem with LAN type of plug would be much easier than a USB type, right? But for that i would have to change ISP.. or just quiting starting linux OS :( Appreciating your help, hoping you can help me to set up my internet in the ubuntu with Speedtouch 330, J.C. On 1/18/07, Joao S. Carvalho [EMAIL PROTECTED] wrote: Hi! I am sorry for delay, but i am working all day and only have a few time at night to linux.. Here it is the syslog and also the messages files so that you can take a look. Hope you figure out what's wrong. Actually, in my first mail i said i followed the steps in the link http://www.guiaubuntupt.org /wiki/index.php?title=SpeedTouch_330http://www.guiaubuntupt.org/wiki/index.php?title=SpeedTouch_330 but that link is wrong, i meant http://bits.webhs.org/bitaites/?p=1786page=2. It's in portuguese, but anyway you can understand it, because no matter the portuguese text the commands are there and i followed the order top down. In a couple of ours i'll run grep CONFIG_ATM_BR2684 /boot/config* and i'll send the output to you. Thanks for help guys, João Carvalho On 1/17/07, Duncan Sands [EMAIL PROTECTED] wrote: Hi J.C., could you please send all of /var/log/syslog. Thanks, Duncan. PS: in http://www.guiaubuntupt.org/wiki/index.php?title=SpeedTouch_330, the host www.guiaubuntupt.org doesn't seem to exist... Liste de diffusion modem ALCATEL SpeedTouch USB Pour se désinscrire : mailto:[EMAIL PROTECTED] ?subject=unsubscribe Liste de diffusion modem ALCATEL SpeedTouch USB Pour se désinscrire : mailto:[EMAIL PROTECTED] -- Jose Bernardo B R Silva | Source Mage GNU/Linux Section Guru [EMAIL PROTECTED]| http://www.sourcemage.org http://counter.li.org #245602 http://cosmos.oninetspeed.pt/jose.bernardo [EMAIL PROTECTED] Liste de diffusion modem ALCATEL SpeedTouch USB Pour se désinscrire : mailto:[EMAIL PROTECTED]
[speedtouch] Re: speedtouch-start doesn't connect
On Fri, 11 Mar 2005 10:24:55 +, Andrew Benton wrote Tonino del Rio wrote: Hello, i have a 2.4 kernel on gentoo and i have installed speedtouch from the portage and I've configured VCI (8) and VPI (32) for Terra Networks ISP in Spain and i only can get this response: Does anyone know what could be wrong here? (kernel config, speedtouch config...) Can the user space tools set up a bridged, PPPoE over ATM connection? I've only been able to do that with the in-kernel tools. Strange, I only got PPPoE over ATM working with the user space drivers. There was a tool to use with the kernel space drivers that I never got to build with kernel 2.6.x (but I think was patched later by another portuguese guy). -- Jose Bernardo B R Silva | Source Mage GNU/Linux Section Guru [EMAIL PROTECTED]| http://www.sourcemage.org http://counter.li.org #245602 http://cosmos.oninetspeed.pt/jose.bernardo [EMAIL PROTECTED] Liste de diffusion modem ALCATEL SpeedTouch USB Pour se désinscrire : mailto:[EMAIL PROTECTED]
[speedtouch] Re: kernel 2.6.5
On Sun, 6 Jun 2004 02:04:22 +0100, Sergio Freire wrote Hi everybody, im using Fedora Core 1 and i have successfuly installed and configure Speedtouch 330 usb modem with kernels 2.4.xx and with some 2.6 versions which were compiled from source. I think until 2.6.3 the user land driver worked, with some but minor problems. On newer 2.6 kernels it just doesn't work, it keeps giving an error after loading firmware : something like usb urb - received signal..., i don't remember now but we can find it on the net very easily after a google search. I have already tried to patch the usbcore.c as someone on the net advised but netiher that way the problem was solved. I also changed a value on modem_run source to a value -1 or 1 (im not sure now) but that also did not solve the problem. To summarize: - what is the problem with the newer 2.6 kernels? - is there any correct solution available or planned? - why, if the connection comes down, im never again able to reconnect? on 2.4 kernels and some 2.6 versions the only way i had to get into a clean state was by removing the usbcore, usb_hci, modules and modprobing them again... this sometimes hangs the kernel any ideas why? maybe its not a speedtouch issue but a kernel one... - why does the kernel module speedtch does not work? i was unable to get it working but there many other guys who face the same problem Sorry if im reposting questions but i was unable to find answers on these subjects and im not the only one. Sergio, I can only add my observations. I was unable to get the kernelspace driver to work because I was unable to compile br2684ctl. But I have the userspace driver working properly with kernel 2.6.5. Kernel 2.6.6 has some serious usb problems here (besides not booting on a sis730 laptop), so I gave up on that one for now. As for getting the connection back up again, the only way I can do that is to kill pppoe3, pppd, modem_run, then unload usbcore and ohci_hcd, then loading those again. The speedtouch.sh script will do the unloading/loading of the modules if you tell it to (/etc/speedtouch.cfg), and in my howto you can see where I added the killall instructions. Regards, --- Jose Bernardo B R Silva | Source Mage GNU/Linux Section Guru [EMAIL PROTECTED]| http://www.sourcemage.org http://counter.li.org #245602 http://cosmos.oninetspeed.pt/jose.bernardo [EMAIL PROTECTED] Liste de diffusion modem ALCATEL SpeedTouch USB Pour se désinscrire : mailto:[EMAIL PROTECTED]
[speedtouch] Re: Problem with Speedtouch 330 Silver modem rev 4
On Sun, 30 May 2004 02:13:25 +0100 (WEST), Sergio Marques wrote Nop, i've tried to follow your howto but it haven't worked. Sorry. Thanks anyway. It seems like the modem it's syncronized (when i do modem_run ... the modem blinks trying to sinc). But when i do with the flag -b (suport for pppoe) ./speedtouch-doctor.sh the return is: You are using linux kernel version 2.4.26 Support for USB is OK Preliminary USB device filesystem is OK OHCI support is OK /dev/ppp is OK HDLC support is OK HDLC support is OK (no bug) pppd version 2.4.2 You are using pppd version (untested) No existing PPP connection... trying to make one (please wait) using channel 21 Failed to set PPP kernel option flags: Inappropriate ioctl for device Using interface ppp0 Connect: ppp0 -- /dev/pts/1 Script /usr/local/sbin/pppoa3 -m 1 -b - c -v 2 -vpi 0 -vci 35 finished (pid 882), status = 0x0 Modem hangup Connection terminated. PPP: very bad ... usermode driver just crashed Ok, so it looks like it is a problem with modem_run and the v4 modem. Are you using the latest version of modem_run? I'm not sure if only the CVS version will work with the silver modem. Try (besides all the other ugly hacks) changing VERBOSE to 1 and DEBUG to 1 in speedtouch.sh, and see what shows in the log when it loads modem_run, if it is able to load the firmware at all. You can even try VERBOSE=2, if VERBOSE=1 does not give enough hints. --- Jose Bernardo B R Silva | Source Mage GNU/Linux Section Guru [EMAIL PROTECTED]| http://www.sourcemage.org http://counter.li.org #245602 http://cosmos.oninetspeed.pt/jose.bernardo [EMAIL PROTECTED] Liste de diffusion modem ALCATEL SpeedTouch USB Pour se désinscrire : mailto:[EMAIL PROTECTED]
[speedtouch] Re: Problem with Speedtouch 330 Silver modem rev 4
On Sat, 29 May 2004 21:31:27 +0100 (WEST), Sergio Marques wrote Citando . [EMAIL PROTECTED]: Aqui nesta linha tenta usar a opção -b para pppoe /usr/local/sbin/pppoa3 -m 1 -c -v 2 -vpi 0 -vci 35, assim está para pppoa... usa usr/bin/pppoa3 -vpi 0 -vci 35 -b -e 1 -m 1 -c, para pppoe Boa sorte Hi, i've trying what you said (/usr/local/sbin/pppoa3 -m 1 -b -e 1 -c -v 2 -vpi 0 -vci 35) with and whithout the flag -e 1 and it has return this: Well, I just got the user mode drivers to work following my own howto (http://cosmos.oninetspeed.pt/jose.bernardo) on a 2.6.x kernel. I was unable to get the kernel mode driver to work, but that might have been because br2864ctl fails to compile with a 2.6 kernel. The main difference now was that I wasn't using MNF, so I just used tap0 as the interface, and called adsl-setup to fill up the *secrets files, etc. Would you like to try my howto, and see if it solves it for you? --- Jose Bernardo B R Silva | Source Mage GNU/Linux Section Guru [EMAIL PROTECTED]| http://www.sourcemage.org http://counter.li.org #245602 http://cosmos.oninetspeed.pt/jose.bernardo [EMAIL PROTECTED] Liste de diffusion modem ALCATEL SpeedTouch USB Pour se désinscrire : mailto:[EMAIL PROTECTED]
[speedtouch] br2684ctl on kernel 2.6.x
On Fri, 9 Jan 2004 10:09:30 +0100, Gilles Espinasse wrote This is because you do not follow the how-to http://www.linux-usb.org/SpeedTouch/docs/howto.html Patching was necessary with old kernel. You don't need anymore to patch the kernel since 2.4.19 For PPPoE you will need these options: a.. Networking Options a.. RFC 1483/2684 Bridged protocols [Y] b.. Network Device Support a.. PPP Over Ethernet (EXPERIMENTAL) [Y] dont forget br2684ctl http://home.sch.bme.hu/%7Ecell/br2684/dist/010402/brctl-010226.c to be compilated with cc -o br2684ctl brctl-010226.c -latm Hi! I am now trying to compile br2684ctl, on a machine with kernel 2.6.6. I get the following: # cc -o br2684ctl brctl-010226.c -latm brctl-010226.c:8:17: atm.h: No such file or directory In file included from /usr/include/linux/atmdev.h:11, from brctl-010226.c:9: /usr/include/linux/atm.h:208: error: parse error before uint32_t /usr/include/linux/atm.h:210: error: parse error before '}' token /usr/include/linux/atm.h:214: error: parameter `addr' has incomplete type brctl-010226.c: In function `assign_vcc': brctl-010226.c:91: error: `T2A_PVC' undeclared (first use in this function) brctl-010226.c:91: error: (Each undeclared identifier is reported only once brctl-010226.c:91: error: for each function it appears in.) Any ideas? It would seem that brctl won't compile on a kernel 2.6.x, is that right? The parse error is fixable by adding #include stdint.h, but the T2A_PVC error I can't fix (yet). --- Jose Bernardo B R Silva | Source Mage GNU/Linux Section Guru [EMAIL PROTECTED]| http://www.sourcemage.org http://counter.li.org #245602 http://cosmos.oninetspeed.pt/jose.bernardo [EMAIL PROTECTED] Liste de diffusion modem ALCATEL SpeedTouch USB Pour se désinscrire : mailto:[EMAIL PROTECTED]
[speedtouch] Re: Line monitoring
On Fri, 23 Apr 2004 09:53:11 +0200, Duncan Sands wrote This is very interesting, so there are problems with the uhci code in 2.6 kernels up to now? Are these general problems or something specific to Speedtouch and line syncing? Not up to now: just that kernel. Some major changes went into the uhci code in the last release (I think), and one change was buggy. Of course this may have nothing to do with your problem. Do you see the same thing with other 2.6 kernels? Just a followup on Duncan's comment, if the kernel you're speaking about is 2.6.5, lots of problems have been reported with bluetooth adapters, usbnet, etc. so it is very definitively the uhci code. The bluez mailing lists has a few recent messages on the usb problems. --- Jose Bernardo B R Silva | Source Mage GNU/Linux Section Guru [EMAIL PROTECTED]| http://www.sourcemage.org http://counter.li.org #245602 http://cosmos.oninetspeed.pt/jose.bernardo [EMAIL PROTECTED] Liste de diffusion modem ALCATEL SpeedTouch USB Pour se désinscrire : mailto:[EMAIL PROTECTED]
[speedtouch] Re: Patch for pppoa3 to support PPPoE bridge under FreeBSD
May I add some info? I use linux (mandrake MNF), but I managed to get a working connection with the 330. Our ISPs in portugal all use PPPOE, PPPOA doesn't work at all. Looking at my howto, I call pppoa3 differently, but I don't know if that is because I am using linux and not FreeBSD; anyway, here is my pppoa3 command line: /usr/bin/pppoa3 -vpi 0 -vci 35 -b -e 1 -m 1 -c Slightly different from the one both my countrymen posted here; I can't check right now what does every switch (I'm at work, no linux here, unfortunately), but I hope this helps. --- Jose Bernardo B R Silva | Source Mage GNU/Linux Section Guru [EMAIL PROTECTED]| http://www.sourcemage.org http://counter.li.org #245602 http://cosmos.oninetspeed.pt/jose.bernardo [EMAIL PROTECTED] -- Original Message --- From: Francois Rogler [EMAIL PROTECTED] To: [EMAIL PROTECTED] Sent: Mon, 14 Jul 2003 06:17:14 +0200 Subject: [speedtouch] Re: Patch for pppoa3 to support PPPoE bridge under FreeBSD On Sun, Jul 13, 2003 at 07:36:19PM +, Nuno Ricardo Gomes Antunes wrote: Hi, I'm experiencing the same dificulties as Nuno Teixeira. I believe we use the same internet provider: sapo. Internet access is still no go :( Anyway, this is what I've done so far: 1 - Added the following to /etc/usbd.conf so that the firmware gets uploaded to the modem as soon as the modem is hotplugged: # Alcatel Speedtouch USB device Alcatel SpeedTouch USB devname ugen[0-9]+ vendor 0x06b9 product 0x4061 attach /usr/local/sbin/modem_run -f /usr/local/libdata/mgmt.o 2 - Added if_tap_load=yes to /boot/loader.conf so that the module gets loaded at startup 3 - Pulled the latest sources from cvs, applied Francois Rogler's 2nd patch for pppoa3, compiled and installed it 4 - Configured /etc/ppp/ppp.conf to include the following: [...] Well thanks for all this feedback, your configuration seems good. I would like to know a few things: Does your provider requires you to connect in pppoe or can you use pppoa ? If your provider allow pppoa, did you first manage to use pppoa3 in normal mode (ie pppoa) ? I don't really know what's the status of freebsd threads, and maybe you would have to use the linux compatibity threads as described in a previous mail by someone else but seems to be a pain in the ass. So to avoid that, I started to backport most of pppoe code in pppoa2 (fork version). I hope to have a version to test later in the week. I'll send it to you. keep going, -- Francois Rogler Liste de diffusion modem ALCATEL SpeedTouch USB Pour se désinscrire : mailto:[EMAIL PROTECTED] --- End of Original Message --- Liste de diffusion modem ALCATEL SpeedTouch USB Pour se désinscrire : mailto:[EMAIL PROTECTED]
[speedtouch] Re: pppoe
And if you find I did something wrong on the howto, or need some clarification, please tell me, I'm following the mailing list and welcome all sugestions. --- Jose Bernardo B R Silva | Source Mage GNU/Linux Developer [EMAIL PROTECTED] | http://www.sourcemage.org http://counter.li.org #245602 http://cosmos.oninetspeed.pt/jose.bernardo [EMAIL PROTECTED] -- Original Message --- From: gilles.espinasse [EMAIL PROTECTED] To: [EMAIL PROTECTED] Sent: Tue, 18 Mar 2003 08:16:05 +0100 Subject: [speedtouch] Re: pppoe Look at http://cosmos.oninetspeed.pt/jose.bernardo/speedtouch.html - Original Message - From: Ryan N. [EMAIL PROTECTED] To: [EMAIL PROTECTED] Sent: Tuesday, March 18, 2003 6:43 AM Subject: [speedtouch] pppoe Hello, I'm currently trying to install a speedtouch usb modem under Sarge Debian but I'm a little unclear on the pppoe instructions. I was wondering if anyone was working on a howto for pppoe and the 1.2 driver, or if there's going to be an update do the standard docs soon. Ryan N. Liste de diffusion modem ALCATEL SpeedTouch USB Pour se désinscrire : mailto:[EMAIL PROTECTED] Liste de diffusion modem ALCATEL SpeedTouch USB Pour se désinscrire : mailto:[EMAIL PROTECTED] --- End of Original Message --- Liste de diffusion modem ALCATEL SpeedTouch USB Pour se désinscrire : mailto:[EMAIL PROTECTED]
[speedtouch] Re: How do I set up my Speedtouch
Also, add to those questions, - Does his isp use pppoe instead of pppoa? - Are his vic/vpi set correctly? --- Jose Bernardo B R Silva | Source Mage GNU/Linux Developer [EMAIL PROTECTED] | http://www.sourcemage.org http://counter.li.org #245602 http://cosmos.oninetspeed.pt/jose.bernardo [EMAIL PROTECTED] -- Original Message --- From: Ok Overbeek (mz) [EMAIL PROTECTED] To: [EMAIL PROTECTED] Sent: Thu, 13 Mar 2003 20:02:40 +0100 Subject: [speedtouch] Re: How do I set up my Speedtouch Hi Martin! This smells terribly of the same little (ahem) problem WE struggled with a few weeks ago The questions that pose themselves are: Did Paul use the beta1 version? Did he check the contents of: - /etc/ppp/peers/adsl - /etc/ppp/pap-secrets chap-secrets etcetera, I would like to add... Ok Paul Hudson wrote: Hi Martin, the return from the ifconfig ppp0 is shown below, ppp0 Link encap:Point-to-Point Protocol POINTOPOINT NOARP MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:3 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) as no inet address is shown I'm assuming something is wrong in my setup. How do I get a syslog output ? I presume the above is not this. Paul Liste de diffusion modem ALCATEL SpeedTouch USB Pour se désinscrire : mailto:[EMAIL PROTECTED] --- End of Original Message --- Liste de diffusion modem ALCATEL SpeedTouch USB Pour se désinscrire : mailto:[EMAIL PROTECTED]
[speedtouch] Re: alcatel speedtouch usb openbsd3.2 generic no answer back
Well, I have a speedtouch 330 working here in Portugal with oninet, so you might want to take a look at what I did at http://cosmos.oninetspeed.pt/jose.bernardo/speedtouch.html, even though it is specific to my firewall's distribution, Mandrake's MNF. But I had to use pppoa3 instead of pppoa2, and pppoe over that to get things working, so that might be the solution. --- Jose Bernardo B R Silva | Source Mage GNU/Linux Developer [EMAIL PROTECTED] | http://www.sourcemage.org http://counter.li.org #245602 [EMAIL PROTECTED] http://cosmos.oninetspeed.pt/jose.bernardo/ -- Original Message --- From: Nuno Morgadinho [EMAIL PROTECTED] To: [EMAIL PROTECTED] Sent: Sat, 8 Mar 2003 15:54:43 + Subject: [speedtouch] alcatel speedtouch usb openbsd3.2 generic no answer back When I try to get ADSL working using Alcatel Speedtouch USB Modem on OpenBSD 3.2 GENERIC I get the following log (in short, there's no answer back). http://neei.uevora.pt/~gotcha/ppp.log2 Here's my /etc/ppp/ppp.conf (the -vpi and -vci values should be ok, iam in portugal):: default: ident user-ppp VERSION (built COMPILATIONDATE) set log Phase Chat IPCP CCP tun command adsl: set authname [EMAIL PROTECTED] set authkey mypassword set device !/usr/local/sbin/pppoa2 -vpi 0 -vci 35 -v 1 accept chap set speed sync set timeout 0 enable lqr set lqrperiod 5 set redial 15 1 set dial set ifaddr 10.0.0.1/0 10.0.0.2/0 255.255.255.0 0.0.0.0 add default HISADDR enable dns Any help would be greatly appreciated, many thanks. Liste de diffusion modem ALCATEL SpeedTouch USB Pour se désinscrire : mailto:[EMAIL PROTECTED] --- End of Original Message --- Liste de diffusion modem ALCATEL SpeedTouch USB Pour se désinscrire : mailto:[EMAIL PROTECTED]
[speedtouch] Re: is someone using the driver with pppoe under gentoo?
If you'd stayed with sourcemage instead of gentoo... ;) Take a look at the howto I posted for mandrake's mnf, since it was made for portugal (oninet speed) and MNF hasn't got hotplug installed, so I didn't use ifup. To get tap1 working, I edited the speedtouch.sh file to add the lines to launch pppoa3 with the -b option, followed by pppoe. I also edited /etc/ppp/pppoe.conf so that it would use the correct tap device. Getting it to work with hotplug might be nice touch, though. --- Jose Bernardo B R Silva | Source Mage GNU/Linux Developer [EMAIL PROTECTED] | http://www.sourcemage.org http://counter.li.org #245602 [EMAIL PROTECTED] -- Original Message --- From: Hugo Portela [EMAIL PROTECTED] To: [EMAIL PROTECTED] [EMAIL PROTECTED] Sent: Fri, 7 Mar 2003 10:17:51 + Subject: [speedtouch] is someone using the driver with pppoe under gentoo? Hello, speedtouch, My debian is working perfectly with the speedtouch1.2 beta1. I decide to give a try to Gentoo, but i am having dificulties to set up the driver. I don't know how to tell hotplug how to bring the tap device up. (gentoo doesn't use ifup, and me being a newbie ...) Any advice/hints will be welcome Best regards. Hugo Portela [EMAIL PROTECTED] 2003-03-07 Liste de diffusion modem ALCATEL SpeedTouch USB Pour se désinscrire : mailto:[EMAIL PROTECTED] --- End of Original Message --- Liste de diffusion modem ALCATEL SpeedTouch USB Pour se désinscrire : mailto:[EMAIL PROTECTED]
[speedtouch] Re: is someone using the driver with pppoe under gentoo?
-- Original Message --- From: Hugo Portela [EMAIL PROTECTED] To: [EMAIL PROTECTED] [EMAIL PROTECTED] Sent: Fri, 7 Mar 2003 10:52:20 + Subject: [speedtouch] Re: is someone using the driver with pppoe under gentoo? Hello, Jose Bernardo Silva, If you'd stayed with sourcemage instead of gentoo... ;) I haven't been able to install it, some months ago :-) I have checked the SM site b4 trying gentoo, but gentoo has better documentation... We are almost ready for a interim release by the end of the month, should be much easier to install. Maybe you'll try it again then? :) Take a look at the howto I posted for mandrake's mnf, since it was made for portugal (oninet speed) and MNF hasn't got hotplug installed, so I didn't use ifup. To get tap1 working, I edited the speedtouch.sh file to add the lines to launch pppoa3 with the -b option, followed by pppoe. I also edited /etc/ppp/pppoe.conf so that it would use the correct tap device. Getting it to work with hotplug might be nice touch, though. what brings up your tap device? In my debian, if i understand correctly the concepts, when something try to use the /dev/net/tun device, hotplug calls ifup tap0 to bring the device up. (look at the following lines from my syslog, the idented line) and make it available. I think (I'm not sure, will have to check at home) that the tap1 device in mnf is created by pppoa3, but failing that... I don't remember seing a line saying anything about the tap interface on syslog, as I only found that tap0 already existed by chance. I'll check. --- Jose Bernardo B R Silva | Source Mage GNU/Linux Developer [EMAIL PROTECTED] | http://www.sourcemage.org http://counter.li.org #245602 [EMAIL PROTECTED] Liste de diffusion modem ALCATEL SpeedTouch USB Pour se désinscrire : mailto:[EMAIL PROTECTED]
[speedtouch] Re: Unable to get speedtouch 330 to work
I've just sent this howto to mandrake's firewall mailing list, now I'm posting it here too, as it might help others like me that are trying to use a speedtouch 330 with your drivers and a Mandrake MNF 8.2 firewall; it might also help with other linux distributions: To recap, for Portugal we have to use pppoe, and vpi is 0 and vci is 35. Now, here are the steps to get the speedtouch 330 to work with MNF: 1 - Get the speedtouch-1.2.1.src.rpm (or later) package from cooker 2 - Do a rpm --rebuild speedtouch-1.2.1.src.rpm at a mdk 8.2 or 9 box (the 9.1 or cooker use glibc 2.3.1, so they don't work in MNF); 3 - install the generated speedtouch binary rpm on mnf 4 - get the alcaudsl.sys file from alcatel/thompson's windows drivers, and copy it to /usr/share/speedtouch as mgmt.o (or edit /etc/speedtouch.conf to point to alcaudsl.sys); 5 - If you don't have it already, do a mkdir /dev/net, then do a mknod c 10 220 /dev/net/tun; 6 - check your /etc/modules.conf for the following entries, if missing add them: alias char-major-108 ppp_generic alias /dev/ppp ppp_generic alias tty-ldisc-3 ppp_async alias tty-ldisc-13 n_hdlc alias tty-ldisc-14 ppp_synctty alias ppp-compress-21 bsd_comp alias ppp-compress-24 ppp_deflate alias ppp-compress-26 ppp_deflate alias char-major-10-200 tun 7 - Configure mnf using the web interface to use pppoa; you won't get connected, but pap-secrets and chap-secrets will get filled up correctly; 8 - edit /etc/ppp/pppoe.conf, and replace the entry 'ETH=' with 'ETH=tap1' - that was what stumbled me for more time, it seems mnf had configured a tap0 entry for my DMZ card, a 3com 3c59x, so when I had that as tap0 it wouldn't work; if you have a entry in /etc/modules.conf as alias tap0 ethertap, you'll need to use tap1 too; 9 - edit /usr/share/speedtouch/speedtouch.sh; in the function connect_ppp(), where you see $PPP call $PEER /dev/null 21, comment that line, and add these 2: /usr/bin/pppoa3 -vpi 0 -vci 35 -b -e 1 -m 1 -c adsl-start 10 - On the same file (/usr/share/speedtouch/speedtouch.sh), find the stop) entry, and add a line with adsl-stop just before the kill_process pppd, and another with killall pppoa3 immediately after 11 - do a /etc/init.d/adsl restart, and your Speedtouch 330 should connect now (check syslog to make sure it doesn't do anymore the RCP connect timeouts, but instead negociates pap or chap; if you get many usb devfs errors with modem_run, do a /etc/init.d/adsl stop, disconnect the modem, reconnect, and try again). 12 - use the web interface to define your zones setup (inside firewall rules), so your wan interface is now the ppp+ interface; 13 - if needed, edit /etc/ez-ipupdate.conf, so the line INTERFACE=ppp0 instead of INTERFACE=eth1, and restart ez-ipupdate - I don't know why, but MNF didn't update this one. As soon as I get a web page up on my new isp, I'm thinking of posting this howto, might help others. Jose Bernardo Silva | Source Mage GNU/Linux Developer [EMAIL PROTECTED] | http://www.sourcemage.org http://counter.li.org #245602 [EMAIL PROTECTED] Liste de diffusion modem ALCATEL SpeedTouch USB Pour se désinscrire : mailto:[EMAIL PROTECTED]
[speedtouch] Re: CRC error in an AAL5 frame
Frans, That fixed it. 50Kbps+! Thanks a lot! It is even faster than the cable I had previously, and that one was supposed to be 640 while ADSL is 512... Changing ISP sure helped... :) --- Jose Bernardo B R Silva | Source Mage GNU/Linux Developer [EMAIL PROTECTED] | http://www.sourcemage.org http://counter.li.org #245602 [EMAIL PROTECTED] -- Original Message --- From: Frans J King [EMAIL PROTECTED] To: [EMAIL PROTECTED] Sent: Sun, 23 Feb 2003 15:48:28 - Subject: [speedtouch] Re: CRC error in an AAL5 frame Try using mgmt.o downloaded from the Alcatel website instead of the windows file. This caused loads of CRC errors for me. Regards, Frans Liste de diffusion modem ALCATEL SpeedTouch USB Pour se désinscrire : mailto:[EMAIL PROTECTED]
[speedtouch] Re: Unable to get speedtouch 330 to work
-- Original Message --- From: Hugo Portela [EMAIL PROTECTED] To: [EMAIL PROTECTED] Sent: Sat, 22 Feb 2003 19:54:54 + Subject: [speedtouch] Re: Unable to get speedtouch 330 to work Jose Bernardo Silva wrote: Answering my own questions, I managed to get further ahead thanks to a posting on sourceforge's forum, by Hugo Rodrigues. Following his indications, I edited the /etc/ppp/peers/adsl file, and changed the options of pppoa3 so that it's line would be /usr/sbin/pppoa3 -b -e 1 -m 1 -c -vpi 0 -vci 35 Now I get the following errors in the log: Feb 21 22:42:35 fwall pppd[15137]: pppd 2.4.1 started by root, uid 0 Feb 21 22:42:35 fwall pppd[15137]: using channel 201 Feb 21 22:42:35 fwall pppd[15137]: Using interface ppp0 Feb 21 22:42:35 fwall pppd[15137]: Connect: ppp0 -- /dev/pts/2 Feb 21 22:42:35 fwall pppoa3[15138]: Error opening tun/tap device. Quitting Feb 21 22:42:35 fwall pppd[15137]: Script /usr/bin/pppoa3 -vpi 0 -vci 35 -b -e 1 -m 1 -c finished (pid 15138), status = 0xff00 Feb 21 22:42:35 fwall pppd[15137]: Modem hangup Feb 21 22:42:35 fwall pppd[15137]: Connection terminated. Feb 21 22:42:35 fwall pppd[15137]: using channel 202 Feb 21 22:42:35 fwall pppd[15137]: Using interface ppp0 Feb 21 22:42:35 fwall pppd[15137]: Connect: ppp0 -- /dev/pts/2 Feb 21 22:42:35 fwall pppoa3[15141]: Error opening tun/tap device. Quitting I believe the driver expect to find the tun/tap device under /dev/net. If your device only exists under /dev (search for tap* files) you can (maybe)create a directory net under /dev and then create a symbolic lynk to /dev/tap0 Thanks Hugo. That I've fixed by now, with a mkdir /dev/net, and a mknod c 10 220 /dev/net/tap0. Now the problem is to configure it all, as it still doesn't work, it launches a bunch of pppoa3, and pppoe doesn't seem to appear in the picture at all. Liste de diffusion modem ALCATEL SpeedTouch USB Pour se désinscrire : mailto:[EMAIL PROTECTED]
[speedtouch] Unable to get speedtouch 330 to work
Hi, can anyone help me? I've checked and rechecked, and I can't get my brand new speedtouch 330 to work with mnf 8.2 (Mandrake's 8.2 based firewall). Here's what I did: I've downloaded the src rpm for the 1.2.1 drivers, rebuilt it on a mandrake 8.2 development machine, and installed it on my mnf. Then, I got the mgmt.o file from alcatel's drivers, copyed it to /usr/share/speedtouch. Step three, I configured the adsl connection on the web interface - this created the /etc/ppp/peers/adsl file, etc. I've checked, and it is correctly filled up. Next, I verified pap-secrets and chap-secrets, and the login ids and passwords checked. Why is it then that I can't connect (when I can connect if I use w2k), and when I enable debug for ppp I get what follows on the syslog: Feb 21 21:24:08 fwall kernel: usb_control/bulk_msg: timeout Feb 21 21:24:08 fwall kernel: usbdevfs: USBDEVFS_BULK failed dev 5 ep 0x85 len 512 ret -110 Feb 21 21:24:33 fwall modem_run[20523]: ADSL synchronization has been obtained Feb 21 21:24:33 fwall modem_run[20523]: ADSL line is up (512 kbit/s down | 128 kbit/s up) Feb 21 21:24:34 fwall kernel: HDLC line discipline: version $Revision: 3.3 $, maxframe=4096 Feb 21 21:24:34 fwall kernel: N_HDLC line discipline registered. Feb 21 21:24:34 fwall pppd[20560]: pppd 2.4.1 started by root, uid 0 Feb 21 21:24:34 fwall pppd[20560]: using channel 73 Feb 21 21:24:34 fwall pppoa3[20563]: pppoa3 version 1.2-beta1 started by root (uid 0) Feb 21 21:24:34 fwall pppd[20560]: Using interface ppp0 Feb 21 21:24:34 fwall pppd[20560]: Connect: ppp0 -- /dev/pts/2 Feb 21 21:24:34 fwall pppoa3[20563]: Control thread ready Feb 21 21:24:34 fwall pppoa3[20568]: host -- pppoa3 -- modem stream ready Feb 21 21:24:34 fwall pppoa3[20569]: modem -- pppoa3 -- host stream ready Feb 21 21:24:35 fwall pppd[20560]: sent [LCP ConfReq id=0x1 asyncmap 0x0 magic 0x9a1983e3] Feb 21 21:24:35 fwall kernel: ppp_synctty: send buffer, count = 20 Feb 21 21:24:35 fwall kernel: FF 03 C0 21 01 01 00 10 ...! Feb 21 21:24:35 fwall kernel: 02 06 00 00 00 00 05 06 Feb 21 21:24:35 fwall kernel: 9A 19 83 E3 Feb 21 21:24:38 fwall pppd[20560]: sent [LCP ConfReq id=0x1 asyncmap 0x0 magic 0x9a1983e3] Feb 21 21:24:38 fwall kernel: ppp_synctty: send buffer, count = 20 Feb 21 21:24:38 fwall kernel: FF 03 C0 21 01 01 00 10 ...! Feb 21 21:24:38 fwall kernel: 02 06 00 00 00 00 05 06 Feb 21 21:24:38 fwall kernel: 9A 19 83 E3 Feb 21 21:24:41 fwall pppd[20560]: sent [LCP ConfReq id=0x1 asyncmap 0x0 magic 0x9a1983e3] Feb 21 21:24:41 fwall kernel: ppp_synctty: send buffer, count = 20 Feb 21 21:24:41 fwall kernel: FF 03 C0 21 01 01 00 10 ...! Feb 21 21:24:41 fwall kernel: 02 06 00 00 00 00 05 06 Feb 21 21:24:41 fwall kernel: 9A 19 83 E3 [...] Feb 21 21:25:05 fwall pppd[20560]: LCP: timeout sending Config-Requests Feb 21 21:25:05 fwall pppd[20560]: Connection terminated. Feb 21 21:25:05 fwall pppoa3[20568]: Error reading from source device Feb 21 21:25:05 fwall pppoa3[20563]: Woken by a sem_post event - Exiting Feb 21 21:25:05 fwall pppoa3[20563]: Write to usb Canceled Feb 21 21:25:05 fwall pppoa3[20563]: Exiting Feb 21 21:25:05 fwall pppd[20560]: using channel 74 Feb 21 21:25:05 fwall pppd[20560]: Using interface ppp0 Feb 21 21:25:05 fwall pppd[20560]: Connect: ppp0 -- /dev/pts/3 Feb 21 21:25:05 fwall pppd[20560]: Script /usr/bin/pppoa3 -vpi 8 -vci 38 -e 1 finished (pid 20563), status = 0xff00 Feb 21 21:25:05 fwall pppoa3[20709]: pppoa3 version 1.2-beta1 started by root (uid 0) Feb 21 21:25:05 fwall pppoa3[20709]: Control thread ready Feb 21 21:25:05 fwall pppoa3[20712]: host -- pppoa3 -- modem stream ready Feb 21 21:25:05 fwall pppoa3[20713]: modem -- pppoa3 -- host stream ready Feb 21 21:25:06 fwall pppd[20560]: sent [LCP ConfReq id=0x2 asyncmap 0x0 magic 0xd42ded7c] Feb 21 21:25:06 fwall kernel: ppp_synctty: send buffer, count = 20 Feb 21 21:25:06 fwall kernel: FF 03 C0 21 01 02 00 10 ...! Feb 21 21:25:06 fwall kernel: 02 06 00 00 00 00 05 06 Feb 21 21:25:06 fwall kernel: D4 2D ED 7C .-.| Feb 21 21:25:09 fwall pppd[20560]: sent [LCP ConfReq id=0x2 asyncmap 0x0 magic 0xd42ded7c] Feb 21 21:25:09 fwall kernel: ppp_synctty: send buffer, count = 20 Feb 21 21:25:09 fwall kernel: FF 03 C0 21 01 02 00 10 ...! Feb 21 21:25:09 fwall kernel: 02 06 00 00 00 00 05 06 Feb 21 21:25:09 fwall kernel: D4 2D ED 7C .-.| Feb 21 21:25:12 fwall pppd[20560]: sent [LCP ConfReq id=0x2 asyncmap 0x0 magic 0xd42ded7c] Feb 21 21:25:12 fwall kernel: ppp_synctty: send buffer, count = 20 Feb 21 21:25:12 fwall kernel: FF 03 C0 21 01 02 00 10 ...! Feb 21 21:25:12 fwall kernel: 02 06 00 00 00 00 05 06 Feb 21 21:25:12 fwall kernel: D4 2D ED 7C .-.| Any help would be welcome... I think it might be related to the values for vci and vpi, anyone knows which should be used for ONI Portugal, or where can I find them on the windows drivers? Thank you. --
[speedtouch] Re: Unable to get speedtouch 330 to work
Answering my own questions, I managed to get further ahead thanks to a posting on sourceforge's forum, by Hugo Rodrigues. Following his indications, I edited the /etc/ppp/peers/adsl file, and changed the options of pppoa3 so that it's line would be /usr/sbin/pppoa3 -b -e 1 -m 1 -c -vpi 0 -vci 35 Now I get the following errors in the log: Feb 21 22:42:35 fwall pppd[15137]: pppd 2.4.1 started by root, uid 0 Feb 21 22:42:35 fwall pppd[15137]: using channel 201 Feb 21 22:42:35 fwall pppd[15137]: Using interface ppp0 Feb 21 22:42:35 fwall pppd[15137]: Connect: ppp0 -- /dev/pts/2 Feb 21 22:42:35 fwall pppoa3[15138]: Error opening tun/tap device. Quitting Feb 21 22:42:35 fwall pppd[15137]: Script /usr/bin/pppoa3 -vpi 0 -vci 35 -b -e 1 -m 1 -c finished (pid 15138), status = 0xff00 Feb 21 22:42:35 fwall pppd[15137]: Modem hangup Feb 21 22:42:35 fwall pppd[15137]: Connection terminated. Feb 21 22:42:35 fwall pppd[15137]: using channel 202 Feb 21 22:42:35 fwall pppd[15137]: Using interface ppp0 Feb 21 22:42:35 fwall pppd[15137]: Connect: ppp0 -- /dev/pts/2 Feb 21 22:42:35 fwall pppoa3[15141]: Error opening tun/tap device. Quitting Feb 21 22:42:35 fwall pppd[15137]: Script /usr/bin/pppoa3 -vpi 0 -vci 35 -b -e 1 -m 1 -c finished (pid 15141), status = 0xff00 [...] Feb 21 22:42:36 fwall pppd[15137]: Modem hangup Feb 21 22:42:36 fwall pppd[15137]: Connection terminated. Feb 21 22:42:36 fwall pppd[15137]: using channel 224 Feb 21 22:42:36 fwall pppd[15137]: Using interface ppp0 Feb 21 22:42:36 fwall pppd[15137]: Connect: ppp0 -- /dev/pts/2 Feb 21 22:42:36 fwall pppoa3[15208]: Error opening tun/tap device. Quitting Feb 21 22:42:36 fwall pppd[15137]: Script /usr/bin/pppoa3 -vpi 0 -vci 35 -b -e 1 -m 1 -c finished (pid 15208), status = 0xff00 Feb 21 22:42:36 fwall pppd[15137]: Modem hangup Feb 21 22:42:36 fwall pppd[15137]: Connection terminated. Feb 21 22:42:36 fwall pppd[15137]: Exit. Any ideas? I'm using Mandrake's MNF 8.2 (a firewall based on mandrake 8.2). Thank you! -- José Bernardo B. R. Silva [EMAIL PROTECTED] Liste de diffusion modem ALCATEL SpeedTouch USB Pour se désinscrire : mailto:[EMAIL PROTECTED]
