Re: [WISPA] Another Ubiquity question
Now in the 7th day of testing on the LM317 DC voltage regulator for the NSM5 and it's all good news. I regulated the voltage up to about 20v average and the LM317 doesn't even get warm. With so little heat dissipation there is likely to be very little loss also. This looks like a solution - - - *Olufemi Adalemo* M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Mon, Oct 22, 2012 at 11:58 AM, Olufemi Adalemo adal...@gmail.com wrote: Yes I was warned about the head dissipation. Ultimately the best option is to plug in a switching DC-DC converter. Will look for one but while I'm waiting this may be the best option, albeit with a huge heat sink - - - *Olufemi Adalemo* M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Sat, Oct 20, 2012 at 1:57 AM, Blair Davis the...@wmwisp.net wrote: Watch the heat dissipation on that... -- On 10/19/2012 5:55 PM, Olufemi Adalemo wrote: A friend of mine suggested that I put a simple DIY LM317 voltage regulator on the line. Just built one and it works to reduce the voltage just enough for you to come in under the limit if you have a 24v solar power supply system http://diyaudioprojects.com/Technical/Voltage-Regulator/ - - - *Olufemi Adalemo* M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 19, 2012 at 1:27 PM, Chris Fabien ch...@lakenetmi.comwrote: My guess would be inconsistent cheapo volt meter or power supply/battery voltage was fluctuating. On Thu, Oct 18, 2012 at 10:24 PM, Greg Ihnen os10ru...@gmail.com wrote: That's what I thought... but... he said: We see 27.3 volts at the battery. And 27.1 volts at the top with no load On Thu, Oct 18, 2012 at 3:57 PM, Chris Fabien ch...@lakenetmi.com wrote: No current = no voltage drop. Ohms Law. On Thu, Oct 18, 2012 at 3:38 PM, Jeromie Reeves jree...@18-30chat.net wrote: The resistance of the length of wire. On Thu, Oct 18, 2012 at 11:03 AM, Greg Ihnen os10ru...@gmail.com wrote: A voltage difference with no load? What's causing the drop? On Thu, Oct 18, 2012 at 10:06 AM, Justin Wilson li...@mtin.net wrote: We see 27.3 volts at the battery. And 27.1 volts at the top with no load. Obviously load will have an impact on this. Justin -Original Message- From: Jeromie Reeves jree...@18-30chat.net Reply-To: WISPA General List wireless@wispa.org Date: Thursday, October 18, 2012 9:15 AM To: WISPA General List wireless@wispa.org Subject: Re: [WISPA] Another Ubiquity question That depends on wire size. That distance is not going to be ethernet so I will assume #12 AWG, 400ft, copper wire, etc. You should be seeing a 5.6% drop under a 1amp load or about 25v under load. On Thu, Oct 18, 2012 at 6:02 AM, Justin Wilson li...@mtin.net wrote: 27 volts at the base. DC has very little loss over 400-500 foot distances. We are seeing about .1 volt loss on a 400 foot run. -Original Message- From: Scott Lambert lamb...@lambertfam.org Reply-To: WISPA General List wireless@wispa.org Date: Thursday, October 18, 2012 12:16 AM To: wireless@wispa.org Subject: Re: [WISPA] Another Ubiquity question On Wed, Oct 17, 2012 at 10:14:03PM -0400, Justin Wilson wrote: Many UBNT deployments running at 27volts of clean DC power. Not saying it's ideal but it works. 27v at the ethernet port or 27v at the base of the tower? -- Scott LambertKC5MLE Unix SysAdmin lamb...@lambertfam.org ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo
Re: [WISPA] Another Ubiquity question
Yes I was warned about the head dissipation. Ultimately the best option is to plug in a switching DC-DC converter. Will look for one but while I'm waiting this may be the best option, albeit with a huge heat sink - - - *Olufemi Adalemo* M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Sat, Oct 20, 2012 at 1:57 AM, Blair Davis the...@wmwisp.net wrote: Watch the heat dissipation on that... -- On 10/19/2012 5:55 PM, Olufemi Adalemo wrote: A friend of mine suggested that I put a simple DIY LM317 voltage regulator on the line. Just built one and it works to reduce the voltage just enough for you to come in under the limit if you have a 24v solar power supply system http://diyaudioprojects.com/Technical/Voltage-Regulator/ - - - *Olufemi Adalemo* M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 19, 2012 at 1:27 PM, Chris Fabien ch...@lakenetmi.com wrote: My guess would be inconsistent cheapo volt meter or power supply/battery voltage was fluctuating. On Thu, Oct 18, 2012 at 10:24 PM, Greg Ihnen os10ru...@gmail.com wrote: That's what I thought... but... he said: We see 27.3 volts at the battery. And 27.1 volts at the top with no load On Thu, Oct 18, 2012 at 3:57 PM, Chris Fabien ch...@lakenetmi.com wrote: No current = no voltage drop. Ohms Law. On Thu, Oct 18, 2012 at 3:38 PM, Jeromie Reeves jree...@18-30chat.net wrote: The resistance of the length of wire. On Thu, Oct 18, 2012 at 11:03 AM, Greg Ihnen os10ru...@gmail.com wrote: A voltage difference with no load? What's causing the drop? On Thu, Oct 18, 2012 at 10:06 AM, Justin Wilson li...@mtin.net wrote: We see 27.3 volts at the battery. And 27.1 volts at the top with no load. Obviously load will have an impact on this. Justin -Original Message- From: Jeromie Reeves jree...@18-30chat.net Reply-To: WISPA General List wireless@wispa.org Date: Thursday, October 18, 2012 9:15 AM To: WISPA General List wireless@wispa.org Subject: Re: [WISPA] Another Ubiquity question That depends on wire size. That distance is not going to be ethernet so I will assume #12 AWG, 400ft, copper wire, etc. You should be seeing a 5.6% drop under a 1amp load or about 25v under load. On Thu, Oct 18, 2012 at 6:02 AM, Justin Wilson li...@mtin.net wrote: 27 volts at the base. DC has very little loss over 400-500 foot distances. We are seeing about .1 volt loss on a 400 foot run. -Original Message- From: Scott Lambert lamb...@lambertfam.org Reply-To: WISPA General List wireless@wispa.org Date: Thursday, October 18, 2012 12:16 AM To: wireless@wispa.org Subject: Re: [WISPA] Another Ubiquity question On Wed, Oct 17, 2012 at 10:14:03PM -0400, Justin Wilson wrote: Many UBNT deployments running at 27volts of clean DC power. Not saying it's ideal but it works. 27v at the ethernet port or 27v at the base of the tower? -- Scott LambertKC5MLE Unix SysAdmin lamb...@lambertfam.org ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing listWireless@wispa.orghttp://lists.wispa.org/mailman/listinfo/wireless -- West Michigan Wireless ISP Allegan, Michigan 49010 269-686-8648 A Division of: Camp Communication Services, INC ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless
Re: [WISPA] Another Ubiquity question
My guess would be inconsistent cheapo volt meter or power supply/battery voltage was fluctuating. On Thu, Oct 18, 2012 at 10:24 PM, Greg Ihnen os10ru...@gmail.com wrote: That's what I thought... but... he said: We see 27.3 volts at the battery. And 27.1 volts at the top with no load On Thu, Oct 18, 2012 at 3:57 PM, Chris Fabien ch...@lakenetmi.com wrote: No current = no voltage drop. Ohms Law. On Thu, Oct 18, 2012 at 3:38 PM, Jeromie Reeves jree...@18-30chat.net wrote: The resistance of the length of wire. On Thu, Oct 18, 2012 at 11:03 AM, Greg Ihnen os10ru...@gmail.com wrote: A voltage difference with no load? What's causing the drop? On Thu, Oct 18, 2012 at 10:06 AM, Justin Wilson li...@mtin.net wrote: We see 27.3 volts at the battery. And 27.1 volts at the top with no load. Obviously load will have an impact on this. Justin -Original Message- From: Jeromie Reeves jree...@18-30chat.net Reply-To: WISPA General List wireless@wispa.org Date: Thursday, October 18, 2012 9:15 AM To: WISPA General List wireless@wispa.org Subject: Re: [WISPA] Another Ubiquity question That depends on wire size. That distance is not going to be ethernet so I will assume #12 AWG, 400ft, copper wire, etc. You should be seeing a 5.6% drop under a 1amp load or about 25v under load. On Thu, Oct 18, 2012 at 6:02 AM, Justin Wilson li...@mtin.net wrote: 27 volts at the base. DC has very little loss over 400-500 foot distances. We are seeing about .1 volt loss on a 400 foot run. -Original Message- From: Scott Lambert lamb...@lambertfam.org Reply-To: WISPA General List wireless@wispa.org Date: Thursday, October 18, 2012 12:16 AM To: wireless@wispa.org Subject: Re: [WISPA] Another Ubiquity question On Wed, Oct 17, 2012 at 10:14:03PM -0400, Justin Wilson wrote: Many UBNT deployments running at 27volts of clean DC power. Not saying it's ideal but it works. 27v at the ethernet port or 27v at the base of the tower? -- Scott LambertKC5MLE Unix SysAdmin lamb...@lambertfam.org ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless
Re: [WISPA] Another Ubiquity question
A friend of mine suggested that I put a simple DIY LM317 voltage regulator on the line. Just built one and it works to reduce the voltage just enough for you to come in under the limit if you have a 24v solar power supply system http://diyaudioprojects.com/Technical/Voltage-Regulator/ - - - *Olufemi Adalemo* M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 19, 2012 at 1:27 PM, Chris Fabien ch...@lakenetmi.com wrote: My guess would be inconsistent cheapo volt meter or power supply/battery voltage was fluctuating. On Thu, Oct 18, 2012 at 10:24 PM, Greg Ihnen os10ru...@gmail.com wrote: That's what I thought... but... he said: We see 27.3 volts at the battery. And 27.1 volts at the top with no load On Thu, Oct 18, 2012 at 3:57 PM, Chris Fabien ch...@lakenetmi.com wrote: No current = no voltage drop. Ohms Law. On Thu, Oct 18, 2012 at 3:38 PM, Jeromie Reeves jree...@18-30chat.net wrote: The resistance of the length of wire. On Thu, Oct 18, 2012 at 11:03 AM, Greg Ihnen os10ru...@gmail.com wrote: A voltage difference with no load? What's causing the drop? On Thu, Oct 18, 2012 at 10:06 AM, Justin Wilson li...@mtin.net wrote: We see 27.3 volts at the battery. And 27.1 volts at the top with no load. Obviously load will have an impact on this. Justin -Original Message- From: Jeromie Reeves jree...@18-30chat.net Reply-To: WISPA General List wireless@wispa.org Date: Thursday, October 18, 2012 9:15 AM To: WISPA General List wireless@wispa.org Subject: Re: [WISPA] Another Ubiquity question That depends on wire size. That distance is not going to be ethernet so I will assume #12 AWG, 400ft, copper wire, etc. You should be seeing a 5.6% drop under a 1amp load or about 25v under load. On Thu, Oct 18, 2012 at 6:02 AM, Justin Wilson li...@mtin.net wrote: 27 volts at the base. DC has very little loss over 400-500 foot distances. We are seeing about .1 volt loss on a 400 foot run. -Original Message- From: Scott Lambert lamb...@lambertfam.org Reply-To: WISPA General List wireless@wispa.org Date: Thursday, October 18, 2012 12:16 AM To: wireless@wispa.org Subject: Re: [WISPA] Another Ubiquity question On Wed, Oct 17, 2012 at 10:14:03PM -0400, Justin Wilson wrote: Many UBNT deployments running at 27volts of clean DC power. Not saying it's ideal but it works. 27v at the ethernet port or 27v at the base of the tower? -- Scott LambertKC5MLE Unix SysAdmin lamb...@lambertfam.org ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless
Re: [WISPA] Another Ubiquity question
wire and connection loss. On 10/18/2012 2:03 PM, Greg Ihnen wrote: A voltage difference with no load? What's causing the drop? On Thu, Oct 18, 2012 at 10:06 AM, Justin Wilson li...@mtin.net wrote: We see 27.3 volts at the battery. And 27.1 volts at the top with no load. Obviously load will have an impact on this. Justin -Original Message- From: Jeromie Reeves jree...@18-30chat.net Reply-To: WISPA General List wireless@wispa.org Date: Thursday, October 18, 2012 9:15 AM To: WISPA General List wireless@wispa.org Subject: Re: [WISPA] Another Ubiquity question That depends on wire size. That distance is not going to be ethernet so I will assume #12 AWG, 400ft, copper wire, etc. You should be seeing a 5.6% drop under a 1amp load or about 25v under load. On Thu, Oct 18, 2012 at 6:02 AM, Justin Wilson li...@mtin.net wrote: 27 volts at the base. DC has very little loss over 400-500 foot distances. We are seeing about .1 volt loss on a 400 foot run. -Original Message- From: Scott Lambert lamb...@lambertfam.org Reply-To: WISPA General List wireless@wispa.org Date: Thursday, October 18, 2012 12:16 AM To: wireless@wispa.org Subject: Re: [WISPA] Another Ubiquity question On Wed, Oct 17, 2012 at 10:14:03PM -0400, Justin Wilson wrote: Many UBNT deployments running at 27volts of clean DC power. Not saying it's ideal but it works. 27v at the ethernet port or 27v at the base of the tower? -- Scott Lambert KC5MLE Unix SysAdmin lamb...@lambertfam.org ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless -- West Michigan Wireless ISP Allegan, Michigan 49010 269-686-8648 A Division of: Camp Communication Services, INC ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless
Re: [WISPA] Another Ubiquity question
I've been in electronics for 30+years. Trust me, there always small variations in voltage on long cable runs, even under no load. -- On 10/18/2012 10:24 PM, Greg Ihnen wrote: That's what I thought... but... he said: "We see 27.3 volts at the battery. And 27.1 volts at the top withno load" On Thu, Oct 18, 2012 at 3:57 PM, Chris Fabien ch...@lakenetmi.com wrote: No current = no voltage drop. Ohms Law. On Thu, Oct 18, 2012 at 3:38 PM, Jeromie Reeves jree...@18-30chat.net wrote: The resistance of the length of wire. On Thu, Oct 18, 2012 at 11:03 AM, Greg Ihnen os10ru...@gmail.com wrote: A voltage difference with no load? What's causing the drop? On Thu, Oct 18, 2012 at 10:06 AM, Justin Wilson li...@mtin.net wrote: We see 27.3 volts at the battery. And 27.1 volts at the top with no load. Obviously load will have an impact on this. Justin -Original Message- From: Jeromie Reeves jree...@18-30chat.net Reply-To: WISPA General List wireless@wispa.org Date: Thursday, October 18, 2012 9:15 AM To: WISPA General List wireless@wispa.org Subject: Re: [WISPA] Another Ubiquity question That depends on wire size. That distance is not going to be ethernet so I will assume #12 AWG, 400ft, copper wire, etc. You should be seeing a 5.6% drop under a 1amp load or about 25v under load. On Thu, Oct 18, 2012 at 6:02 AM, Justin Wilson li...@mtin.net wrote: 27 volts at the base. DC has very little loss over 400-500 foot distances. We are seeing about .1 volt loss on a 400 foot run. -Original Message- From: Scott Lambert lamb...@lambertfam.org Reply-To: WISPA General List wireless@wispa.org Date: Thursday, October 18, 2012 12:16 AM To: wireless@wispa.org Subject: Re: [WISPA] Another Ubiquity question On Wed, Oct 17, 2012 at 10:14:03PM -0400, Justin Wilson wrote: Many UBNT deployments running at 27volts of clean DC power. Not saying it's ideal but it works. 27v at the ethernet port or 27v at the base of the tower? -- Scott Lambert KC5MLEUnix SysAdmin lamb...@lambertfam.org ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless -- West Michigan Wireless ISP Allegan, Michigan 49010 269-686-8648 A Division of: Camp Communication Services, INC ___ Wireless mailing lis
Re: [WISPA] Another Ubiquity question
Watch the heat dissipation on that... -- On 10/19/2012 5:55 PM, Olufemi Adalemo wrote: A friend of mine suggested that I put a simple DIY LM317 voltage regulator on the line. Just built one and it works to reduce the voltage just enough for you to come in under the limit if you have a 24v solar power supply system http://diyaudioprojects.com/Technical/Voltage-Regulator/ - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 19, 2012 at 1:27 PM, Chris Fabien ch...@lakenetmi.com wrote: My guess would be inconsistent cheapo volt meter or power supply/battery voltage was fluctuating. On Thu, Oct 18, 2012 at 10:24 PM, Greg Ihnen os10ru...@gmail.com wrote: That's what I thought... but... he said: "We see 27.3 volts at the battery. And 27.1 volts at the top with no load" On Thu, Oct 18, 2012 at 3:57 PM, Chris Fabien ch...@lakenetmi.com wrote: No current = no voltage drop. Ohms Law. On Thu, Oct 18, 2012 at 3:38 PM, Jeromie Reeves jree...@18-30chat.net wrote: The resistance of the length of wire. On Thu, Oct 18, 2012 at 11:03 AM, Greg Ihnen os10ru...@gmail.com wrote: A voltage difference with no load? What's causing the drop? On Thu, Oct 18, 2012 at 10:06 AM, Justin Wilson li...@mtin.net wrote: We see 27.3 volts at the battery. And 27.1 volts at the top with no load. Obviously load will have an impact on this. Justin -Original Message- From: Jeromie Reeves jree...@18-30chat.net Reply-To: WISPA General List wireless@wispa.org Date: Thursday, October 18, 2012 9:15 AM To: WISPA General List wireless@wispa.org Subject: Re: [WISPA] Another Ubiquity question That depends on wire size. That distance is not going to be ethernet so I will assume #12 AWG, 400ft, copper wire, etc. You should be seeing a 5.6% drop under a 1amp load or about 25v under load. On Thu, Oct 18, 2012 at 6:02 AM, Justin Wilson li...@mtin.net wrote: 27 volts at the base. DC has very little loss over 400-500 foot distances. We are seeing about .1 volt loss on a 400 foot run. -Original Message- From: Scott Lambert lamb...@lambertfam.org Reply-To: WISPA General List wireless@wispa.org Date: Thursday, October 18, 2012 12:16 AM To: wireless@wispa.org Subject: Re: [WISPA] Another Ubiquity question On Wed, Oct 17, 2012 at 10:14:03PM -0400, Justin Wilson wrote: Many UBNT deployments running at 27volts of clean DC power. Not saying it's ideal but it works. 27v at the ethernet port or 27v at the base of the tower? -- Scott Lambert KC5MLEUnix SysAdmin lamb...@lambertfam.org ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless
Re: [WISPA] Another Ubiquity question
27 volts at the base. DC has very little loss over 400-500 foot distances. We are seeing about .1 volt loss on a 400 foot run. -Original Message- From: Scott Lambert lamb...@lambertfam.org Reply-To: WISPA General List wireless@wispa.org Date: Thursday, October 18, 2012 12:16 AM To: wireless@wispa.org Subject: Re: [WISPA] Another Ubiquity question On Wed, Oct 17, 2012 at 10:14:03PM -0400, Justin Wilson wrote: Many UBNT deployments running at 27volts of clean DC power. Not saying it's ideal but it works. 27v at the ethernet port or 27v at the base of the tower? -- Scott LambertKC5MLE Unix SysAdmin lamb...@lambertfam.org ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless
Re: [WISPA] Another Ubiquity question
That depends on wire size. That distance is not going to be ethernet so I will assume #12 AWG, 400ft, copper wire, etc. You should be seeing a 5.6% drop under a 1amp load or about 25v under load. On Thu, Oct 18, 2012 at 6:02 AM, Justin Wilson li...@mtin.net wrote: 27 volts at the base. DC has very little loss over 400-500 foot distances. We are seeing about .1 volt loss on a 400 foot run. -Original Message- From: Scott Lambert lamb...@lambertfam.org Reply-To: WISPA General List wireless@wispa.org Date: Thursday, October 18, 2012 12:16 AM To: wireless@wispa.org Subject: Re: [WISPA] Another Ubiquity question On Wed, Oct 17, 2012 at 10:14:03PM -0400, Justin Wilson wrote: Many UBNT deployments running at 27volts of clean DC power. Not saying it's ideal but it works. 27v at the ethernet port or 27v at the base of the tower? -- Scott LambertKC5MLE Unix SysAdmin lamb...@lambertfam.org ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless
Re: [WISPA] Another Ubiquity question
We see 27.3 volts at the battery. And 27.1 volts at the top with no load. Obviously load will have an impact on this. Justin -Original Message- From: Jeromie Reeves jree...@18-30chat.net Reply-To: WISPA General List wireless@wispa.org Date: Thursday, October 18, 2012 9:15 AM To: WISPA General List wireless@wispa.org Subject: Re: [WISPA] Another Ubiquity question That depends on wire size. That distance is not going to be ethernet so I will assume #12 AWG, 400ft, copper wire, etc. You should be seeing a 5.6% drop under a 1amp load or about 25v under load. On Thu, Oct 18, 2012 at 6:02 AM, Justin Wilson li...@mtin.net wrote: 27 volts at the base. DC has very little loss over 400-500 foot distances. We are seeing about .1 volt loss on a 400 foot run. -Original Message- From: Scott Lambert lamb...@lambertfam.org Reply-To: WISPA General List wireless@wispa.org Date: Thursday, October 18, 2012 12:16 AM To: wireless@wispa.org Subject: Re: [WISPA] Another Ubiquity question On Wed, Oct 17, 2012 at 10:14:03PM -0400, Justin Wilson wrote: Many UBNT deployments running at 27volts of clean DC power. Not saying it's ideal but it works. 27v at the ethernet port or 27v at the base of the tower? -- Scott LambertKC5MLE Unix SysAdmin lamb...@lambertfam.org ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless
Re: [WISPA] Another Ubiquity question
Call me Stupid... but what is the point of this discussion ? Operating the Radios @ 27V is exceeding the Mfg. Specs. . Will they work ? maybe... Will they fail ? maybe If you burn them up. you are on your own.. ? or at least at UBNT's discretion, since you are voiding the warranty, by operating our of Specs. Will it shorten the life of the Radio ? maybe... Will is just work fine ? maybe. This reminds me of the discussions on the CPU Over-Clockers Forum.. If you want to play, sure nothing wrong with that.. but you are on your own .. If you expect it to preform well for a long time, then it is best to stay within the Mfg. Specs ... I have often said this to folks In our industry, when you exceed Specs things don't just 'break' but they do start doing 'funky stuff' Of Course YMMV :) Faisal Imtiaz Snappy Internet Telecom On 10/18/2012 10:06 AM, Justin Wilson wrote: We see 27.3 volts at the battery. And 27.1 volts at the top with no load. Obviously load will have an impact on this. Justin -Original Message- From: Jeromie Reeves jree...@18-30chat.net Reply-To: WISPA General List wireless@wispa.org Date: Thursday, October 18, 2012 9:15 AM To: WISPA General List wireless@wispa.org Subject: Re: [WISPA] Another Ubiquity question That depends on wire size. That distance is not going to be ethernet so I will assume #12 AWG, 400ft, copper wire, etc. You should be seeing a 5.6% drop under a 1amp load or about 25v under load. On Thu, Oct 18, 2012 at 6:02 AM, Justin Wilson li...@mtin.net wrote: 27 volts at the base. DC has very little loss over 400-500 foot distances. We are seeing about .1 volt loss on a 400 foot run. -Original Message- From: Scott Lambert lamb...@lambertfam.org Reply-To: WISPA General List wireless@wispa.org Date: Thursday, October 18, 2012 12:16 AM To: wireless@wispa.org Subject: Re: [WISPA] Another Ubiquity question On Wed, Oct 17, 2012 at 10:14:03PM -0400, Justin Wilson wrote: Many UBNT deployments running at 27volts of clean DC power. Not saying it's ideal but it works. 27v at the ethernet port or 27v at the base of the tower? -- Scott LambertKC5MLE Unix SysAdmin lamb...@lambertfam.org ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless
Re: [WISPA] Another Ubiquity question
Because batteries are 27v. On Oct 18, 2012 10:45 AM, Faisal Imtiaz fai...@snappydsl.net wrote: Call me Stupid... but what is the point of this discussion ? Operating the Radios @ 27V is exceeding the Mfg. Specs. . Will they work ? maybe... Will they fail ? maybe If you burn them up. you are on your own.. ? or at least at UBNT's discretion, since you are voiding the warranty, by operating our of Specs. Will it shorten the life of the Radio ? maybe... Will is just work fine ? maybe. This reminds me of the discussions on the CPU Over-Clockers Forum.. If you want to play, sure nothing wrong with that.. but you are on your own .. If you expect it to preform well for a long time, then it is best to stay within the Mfg. Specs ... I have often said this to folks In our industry, when you exceed Specs things don't just 'break' but they do start doing 'funky stuff' Of Course YMMV :) Faisal Imtiaz Snappy Internet Telecom On 10/18/2012 10:06 AM, Justin Wilson wrote: We see 27.3 volts at the battery. And 27.1 volts at the top with no load. Obviously load will have an impact on this. Justin -Original Message- From: Jeromie Reeves jree...@18-30chat.net Reply-To: WISPA General List wireless@wispa.org Date: Thursday, October 18, 2012 9:15 AM To: WISPA General List wireless@wispa.org Subject: Re: [WISPA] Another Ubiquity question That depends on wire size. That distance is not going to be ethernet so I will assume #12 AWG, 400ft, copper wire, etc. You should be seeing a 5.6% drop under a 1amp load or about 25v under load. On Thu, Oct 18, 2012 at 6:02 AM, Justin Wilson li...@mtin.net wrote: 27 volts at the base. DC has very little loss over 400-500 foot distances. We are seeing about .1 volt loss on a 400 foot run. -Original Message- From: Scott Lambert lamb...@lambertfam.org Reply-To: WISPA General List wireless@wispa.org Date: Thursday, October 18, 2012 12:16 AM To: wireless@wispa.org Subject: Re: [WISPA] Another Ubiquity question On Wed, Oct 17, 2012 at 10:14:03PM -0400, Justin Wilson wrote: Many UBNT deployments running at 27volts of clean DC power. Not saying it's ideal but it works. 27v at the ethernet port or 27v at the base of the tower? -- Scott LambertKC5MLE Unix SysAdmin lamb...@lambertfam.org ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless
Re: [WISPA] Another Ubiquity question
U mean the Charge current is 27-28V.for 24v Batteries... Yes, it would be nice to have the equipment rated for 28-30V like the Mikrotik's But that is something we need to ask Ubiquiti to do Pushing the existing equipment to 27v, has been documented to be 'in-consistent' . :) Faisal Imtiaz Snappy Internet Telecom 7266 SW 48 Street Miami, Fl 33155 Tel: 305 663 5518 x 232 Helpdesk: 305 663 5518 option 2 Email: supp...@snappydsl.net On 10/18/2012 10:49 AM, Josh Luthman wrote: Because batteries are 27v. On Oct 18, 2012 10:45 AM, Faisal Imtiaz fai...@snappydsl.net mailto:fai...@snappydsl.net wrote: Call me Stupid... but what is the point of this discussion ? Operating the Radios @ 27V is exceeding the Mfg. Specs. . Will they work ? maybe... Will they fail ? maybe If you burn them up. you are on your own.. ? or at least at UBNT's discretion, since you are voiding the warranty, by operating our of Specs. Will it shorten the life of the Radio ? maybe... Will is just work fine ? maybe. This reminds me of the discussions on the CPU Over-Clockers Forum.. If you want to play, sure nothing wrong with that.. but you are on your own .. If you expect it to preform well for a long time, then it is best to stay within the Mfg. Specs ... I have often said this to folks In our industry, when you exceed Specs things don't just 'break' but they do start doing 'funky stuff' Of Course YMMV :) Faisal Imtiaz Snappy Internet Telecom On 10/18/2012 10:06 AM, Justin Wilson wrote: We see 27.3 volts at the battery. And 27.1 volts at the top with no load. Obviously load will have an impact on this. Justin -Original Message- From: Jeromie Reeves jree...@18-30chat.net mailto:jree...@18-30chat.net Reply-To: WISPA General List wireless@wispa.org mailto:wireless@wispa.org Date: Thursday, October 18, 2012 9:15 AM To: WISPA General List wireless@wispa.org mailto:wireless@wispa.org Subject: Re: [WISPA] Another Ubiquity question That depends on wire size. That distance is not going to be ethernet so I will assume #12 AWG, 400ft, copper wire, etc. You should be seeing a 5.6% drop under a 1amp load or about 25v under load. On Thu, Oct 18, 2012 at 6:02 AM, Justin Wilson li...@mtin.net mailto:li...@mtin.net wrote: 27 volts at the base. DC has very little loss over 400-500 foot distances. We are seeing about .1 volt loss on a 400 foot run. -Original Message- From: Scott Lambert lamb...@lambertfam.org mailto:lamb...@lambertfam.org Reply-To: WISPA General List wireless@wispa.org mailto:wireless@wispa.org Date: Thursday, October 18, 2012 12:16 AM To: wireless@wispa.org mailto:wireless@wispa.org Subject: Re: [WISPA] Another Ubiquity question On Wed, Oct 17, 2012 at 10:14:03PM -0400, Justin Wilson wrote: Many UBNT deployments running at 27volts of clean DC power. Not saying it's ideal but it works. 27v at the ethernet port or 27v at the base of the tower? -- Scott LambertKC5MLE Unix SysAdmin lamb...@lambertfam.org mailto:lamb...@lambertfam.org ___ Wireless mailing list Wireless@wispa.org mailto:Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org mailto:Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org mailto:Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org mailto:Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org mailto:Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless
Re: [WISPA] Another Ubiquity question
I just put up 2 new solar panels yesterday to replace 2 that were now to small of wattage to cover the expanded load at the tower. Panels with no load were putting out 35 vdc, at the batteries with load I was seeing 28 vdc. I use the tycon voltage regulator to maintain 24 vdc to the radios. Added cost, yes, but this is a remote site with important backhaul and I don’t need to burn a radio out. I was also taking 12 vdc from one of the batteries, but found it would drain it in about 2 weeks... the batteries do not charge evenly, maybe one of our EE members can explain this. 4 12 vdc batteries, 2 in series, then the 2 sets in parallel., most equipment is taken from the 24 vdc, one switch takes power from the 12 vdc. Why does this not keep all batteries charged equally, when using the solar at +27 volts. Tim Kerns CV-Access, Inc. From: Josh Luthman Sent: Thursday, October 18, 2012 7:49 AM To: WISPA General List ; fai...@snappydsl.net Subject: Re: [WISPA] Another Ubiquity question Because batteries are 27v. On Oct 18, 2012 10:45 AM, Faisal Imtiaz fai...@snappydsl.net wrote: Call me Stupid... but what is the point of this discussion ? Operating the Radios @ 27V is exceeding the Mfg. Specs. . Will they work ? maybe... Will they fail ? maybe If you burn them up. you are on your own.. ? or at least at UBNT's discretion, since you are voiding the warranty, by operating our of Specs. Will it shorten the life of the Radio ? maybe... Will is just work fine ? maybe. This reminds me of the discussions on the CPU Over-Clockers Forum.. If you want to play, sure nothing wrong with that.. but you are on your own .. If you expect it to preform well for a long time, then it is best to stay within the Mfg. Specs ... I have often said this to folks In our industry, when you exceed Specs things don't just 'break' but they do start doing 'funky stuff' Of Course YMMV :) Faisal Imtiaz Snappy Internet Telecom On 10/18/2012 10:06 AM, Justin Wilson wrote: We see 27.3 volts at the battery. And 27.1 volts at the top with no load. Obviously load will have an impact on this. Justin -Original Message- From: Jeromie Reeves jree...@18-30chat.net Reply-To: WISPA General List wireless@wispa.org Date: Thursday, October 18, 2012 9:15 AM To: WISPA General List wireless@wispa.org Subject: Re: [WISPA] Another Ubiquity question That depends on wire size. That distance is not going to be ethernet so I will assume #12 AWG, 400ft, copper wire, etc. You should be seeing a 5.6% drop under a 1amp load or about 25v under load. On Thu, Oct 18, 2012 at 6:02 AM, Justin Wilson li...@mtin.net wrote: 27 volts at the base. DC has very little loss over 400-500 foot distances. We are seeing about .1 volt loss on a 400 foot run. -Original Message- From: Scott Lambert lamb...@lambertfam.org Reply-To: WISPA General List wireless@wispa.org Date: Thursday, October 18, 2012 12:16 AM To: wireless@wispa.org Subject: Re: [WISPA] Another Ubiquity question On Wed, Oct 17, 2012 at 10:14:03PM -0400, Justin Wilson wrote: Many UBNT deployments running at 27volts of clean DC power. Not saying it's ideal but it works. 27v at the ethernet port or 27v at the base of the tower? -- Scott LambertKC5MLE Unix SysAdmin lamb...@lambertfam.org ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless
Re: [WISPA] Another Ubiquity question
Because you are pulling more energy from a given cell. Current typically flows in one direction at a time. If you are pulling current off of the whole system all the time, AND pulling more from part of the system, then there is never a chance for the system to come back to equilibrium. Think of it like having four tanks of water each connected with siphon hoses. If you have two hoses pulling water from one of the tanks, it will drain faster than the other three tanks with only one hose. Your charger doesn't realize that one cell is being drained faster as it is only looking at total voltage across the system. Cameron On Thu, Oct 18, 2012 at 10:36 AM, Tim Kerns t...@cv-access.com wrote: I just put up 2 new solar panels yesterday to replace 2 that were now to small of wattage to cover the expanded load at the tower. Panels with no load were putting out 35 vdc, at the batteries with load I was seeing 28 vdc. I use the tycon voltage regulator to maintain 24 vdc to the radios. Added cost, yes, but this is a remote site with important backhaul and I don’t need to burn a radio out. I was also taking 12 vdc from one of the batteries, but found it would drain it in about 2 weeks... the batteries do not charge evenly, maybe one of our EE members can explain this. 4 12 vdc batteries, 2 in series, then the 2 sets in parallel., most equipment is taken from the 24 vdc, one switch takes power from the 12 vdc. Why does this not keep all batteries charged equally, when using the solar at +27 volts. Tim Kerns CV-Access, Inc. *From:* Josh Luthman j...@imaginenetworksllc.com *Sent:* Thursday, October 18, 2012 7:49 AM *To:* WISPA General List wireless@wispa.org ; fai...@snappydsl.net *Subject:* Re: [WISPA] Another Ubiquity question Because batteries are 27v. On Oct 18, 2012 10:45 AM, Faisal Imtiaz fai...@snappydsl.net wrote: Call me Stupid... but what is the point of this discussion ? Operating the Radios @ 27V is exceeding the Mfg. Specs. . Will they work ? maybe... Will they fail ? maybe If you burn them up. you are on your own.. ? or at least at UBNT's discretion, since you are voiding the warranty, by operating our of Specs. Will it shorten the life of the Radio ? maybe... Will is just work fine ? maybe. This reminds me of the discussions on the CPU Over-Clockers Forum.. If you want to play, sure nothing wrong with that.. but you are on your own .. If you expect it to preform well for a long time, then it is best to stay within the Mfg. Specs ... I have often said this to folks In our industry, when you exceed Specs things don't just 'break' but they do start doing 'funky stuff' Of Course YMMV :) Faisal Imtiaz Snappy Internet Telecom On 10/18/2012 10:06 AM, Justin Wilson wrote: We see 27.3 volts at the battery. And 27.1 volts at the top with no load. Obviously load will have an impact on this. Justin -Original Message- From: Jeromie Reeves jree...@18-30chat.net Reply-To: WISPA General List wireless@wispa.org Date: Thursday, October 18, 2012 9:15 AM To: WISPA General List wireless@wispa.org Subject: Re: [WISPA] Another Ubiquity question That depends on wire size. That distance is not going to be ethernet so I will assume #12 AWG, 400ft, copper wire, etc. You should be seeing a 5.6% drop under a 1amp load or about 25v under load. On Thu, Oct 18, 2012 at 6:02 AM, Justin Wilson li...@mtin.net wrote: 27 volts at the base. DC has very little loss over 400-500 foot distances. We are seeing about .1 volt loss on a 400 foot run. -Original Message- From: Scott Lambert lamb...@lambertfam.org Reply-To: WISPA General List wireless@wispa.org Date: Thursday, October 18, 2012 12:16 AM To: wireless@wispa.org Subject: Re: [WISPA] Another Ubiquity question On Wed, Oct 17, 2012 at 10:14:03PM -0400, Justin Wilson wrote: Many UBNT deployments running at 27volts of clean DC power. Not saying it's ideal but it works. 27v at the ethernet port or 27v at the base of the tower? -- Scott LambertKC5MLE Unix SysAdmin lamb...@lambertfam.org ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman
Re: [WISPA] Another Ubiquity question
A voltage difference with no load? What's causing the drop? On Thu, Oct 18, 2012 at 10:06 AM, Justin Wilson li...@mtin.net wrote: We see 27.3 volts at the battery. And 27.1 volts at the top with no load. Obviously load will have an impact on this. Justin -Original Message- From: Jeromie Reeves jree...@18-30chat.net Reply-To: WISPA General List wireless@wispa.org Date: Thursday, October 18, 2012 9:15 AM To: WISPA General List wireless@wispa.org Subject: Re: [WISPA] Another Ubiquity question That depends on wire size. That distance is not going to be ethernet so I will assume #12 AWG, 400ft, copper wire, etc. You should be seeing a 5.6% drop under a 1amp load or about 25v under load. On Thu, Oct 18, 2012 at 6:02 AM, Justin Wilson li...@mtin.net wrote: 27 volts at the base. DC has very little loss over 400-500 foot distances. We are seeing about .1 volt loss on a 400 foot run. -Original Message- From: Scott Lambert lamb...@lambertfam.org Reply-To: WISPA General List wireless@wispa.org Date: Thursday, October 18, 2012 12:16 AM To: wireless@wispa.org Subject: Re: [WISPA] Another Ubiquity question On Wed, Oct 17, 2012 at 10:14:03PM -0400, Justin Wilson wrote: Many UBNT deployments running at 27volts of clean DC power. Not saying it's ideal but it works. 27v at the ethernet port or 27v at the base of the tower? -- Scott LambertKC5MLE Unix SysAdmin lamb...@lambertfam.org ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless
Re: [WISPA] Another Ubiquity question
The resistance of the length of wire. On Thu, Oct 18, 2012 at 11:03 AM, Greg Ihnen os10ru...@gmail.com wrote: A voltage difference with no load? What's causing the drop? On Thu, Oct 18, 2012 at 10:06 AM, Justin Wilson li...@mtin.net wrote: We see 27.3 volts at the battery. And 27.1 volts at the top with no load. Obviously load will have an impact on this. Justin -Original Message- From: Jeromie Reeves jree...@18-30chat.net Reply-To: WISPA General List wireless@wispa.org Date: Thursday, October 18, 2012 9:15 AM To: WISPA General List wireless@wispa.org Subject: Re: [WISPA] Another Ubiquity question That depends on wire size. That distance is not going to be ethernet so I will assume #12 AWG, 400ft, copper wire, etc. You should be seeing a 5.6% drop under a 1amp load or about 25v under load. On Thu, Oct 18, 2012 at 6:02 AM, Justin Wilson li...@mtin.net wrote: 27 volts at the base. DC has very little loss over 400-500 foot distances. We are seeing about .1 volt loss on a 400 foot run. -Original Message- From: Scott Lambert lamb...@lambertfam.org Reply-To: WISPA General List wireless@wispa.org Date: Thursday, October 18, 2012 12:16 AM To: wireless@wispa.org Subject: Re: [WISPA] Another Ubiquity question On Wed, Oct 17, 2012 at 10:14:03PM -0400, Justin Wilson wrote: Many UBNT deployments running at 27volts of clean DC power. Not saying it's ideal but it works. 27v at the ethernet port or 27v at the base of the tower? -- Scott LambertKC5MLE Unix SysAdmin lamb...@lambertfam.org ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless
Re: [WISPA] Another Ubiquity question
That is a great way to explain it. This also causes a lot of other issues with the cell/bank. As the one battery dies and takes less voltage the rest start taking a higher voltage and over charge and out gas leading to dry cells. On Thu, Oct 18, 2012 at 8:49 AM, Cameron Crum cc...@wispmon.com wrote: Because you are pulling more energy from a given cell. Current typically flows in one direction at a time. If you are pulling current off of the whole system all the time, AND pulling more from part of the system, then there is never a chance for the system to come back to equilibrium. Think of it like having four tanks of water each connected with siphon hoses. If you have two hoses pulling water from one of the tanks, it will drain faster than the other three tanks with only one hose. Your charger doesn't realize that one cell is being drained faster as it is only looking at total voltage across the system. Cameron On Thu, Oct 18, 2012 at 10:36 AM, Tim Kerns t...@cv-access.com wrote: I just put up 2 new solar panels yesterday to replace 2 that were now to small of wattage to cover the expanded load at the tower. Panels with no load were putting out 35 vdc, at the batteries with load I was seeing 28 vdc. I use the tycon voltage regulator to maintain 24 vdc to the radios. Added cost, yes, but this is a remote site with important backhaul and I don’t need to burn a radio out. I was also taking 12 vdc from one of the batteries, but found it would drain it in about 2 weeks... the batteries do not charge evenly, maybe one of our EE members can explain this. 4 12 vdc batteries, 2 in series, then the 2 sets in parallel., most equipment is taken from the 24 vdc, one switch takes power from the 12 vdc. Why does this not keep all batteries charged equally, when using the solar at +27 volts. Tim Kerns CV-Access, Inc. From: Josh Luthman Sent: Thursday, October 18, 2012 7:49 AM To: WISPA General List ; fai...@snappydsl.net Subject: Re: [WISPA] Another Ubiquity question Because batteries are 27v. On Oct 18, 2012 10:45 AM, Faisal Imtiaz fai...@snappydsl.net wrote: Call me Stupid... but what is the point of this discussion ? Operating the Radios @ 27V is exceeding the Mfg. Specs. . Will they work ? maybe... Will they fail ? maybe If you burn them up. you are on your own.. ? or at least at UBNT's discretion, since you are voiding the warranty, by operating our of Specs. Will it shorten the life of the Radio ? maybe... Will is just work fine ? maybe. This reminds me of the discussions on the CPU Over-Clockers Forum.. If you want to play, sure nothing wrong with that.. but you are on your own .. If you expect it to preform well for a long time, then it is best to stay within the Mfg. Specs ... I have often said this to folks In our industry, when you exceed Specs things don't just 'break' but they do start doing 'funky stuff' Of Course YMMV :) Faisal Imtiaz Snappy Internet Telecom On 10/18/2012 10:06 AM, Justin Wilson wrote: We see 27.3 volts at the battery. And 27.1 volts at the top with no load. Obviously load will have an impact on this. Justin -Original Message- From: Jeromie Reeves jree...@18-30chat.net Reply-To: WISPA General List wireless@wispa.org Date: Thursday, October 18, 2012 9:15 AM To: WISPA General List wireless@wispa.org Subject: Re: [WISPA] Another Ubiquity question That depends on wire size. That distance is not going to be ethernet so I will assume #12 AWG, 400ft, copper wire, etc. You should be seeing a 5.6% drop under a 1amp load or about 25v under load. On Thu, Oct 18, 2012 at 6:02 AM, Justin Wilson li...@mtin.net wrote: 27 volts at the base. DC has very little loss over 400-500 foot distances. We are seeing about .1 volt loss on a 400 foot run. -Original Message- From: Scott Lambert lamb...@lambertfam.org Reply-To: WISPA General List wireless@wispa.org Date: Thursday, October 18, 2012 12:16 AM To: wireless@wispa.org Subject: Re: [WISPA] Another Ubiquity question On Wed, Oct 17, 2012 at 10:14:03PM -0400, Justin Wilson wrote: Many UBNT deployments running at 27volts of clean DC power. Not saying it's ideal but it works. 27v at the ethernet port or 27v at the base of the tower? -- Scott LambertKC5MLE Unix SysAdmin lamb...@lambertfam.org ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless
Re: [WISPA] Another Ubiquity question
No current = no voltage drop. Ohms Law. On Thu, Oct 18, 2012 at 3:38 PM, Jeromie Reeves jree...@18-30chat.net wrote: The resistance of the length of wire. On Thu, Oct 18, 2012 at 11:03 AM, Greg Ihnen os10ru...@gmail.com wrote: A voltage difference with no load? What's causing the drop? On Thu, Oct 18, 2012 at 10:06 AM, Justin Wilson li...@mtin.net wrote: We see 27.3 volts at the battery. And 27.1 volts at the top with no load. Obviously load will have an impact on this. Justin -Original Message- From: Jeromie Reeves jree...@18-30chat.net Reply-To: WISPA General List wireless@wispa.org Date: Thursday, October 18, 2012 9:15 AM To: WISPA General List wireless@wispa.org Subject: Re: [WISPA] Another Ubiquity question That depends on wire size. That distance is not going to be ethernet so I will assume #12 AWG, 400ft, copper wire, etc. You should be seeing a 5.6% drop under a 1amp load or about 25v under load. On Thu, Oct 18, 2012 at 6:02 AM, Justin Wilson li...@mtin.net wrote: 27 volts at the base. DC has very little loss over 400-500 foot distances. We are seeing about .1 volt loss on a 400 foot run. -Original Message- From: Scott Lambert lamb...@lambertfam.org Reply-To: WISPA General List wireless@wispa.org Date: Thursday, October 18, 2012 12:16 AM To: wireless@wispa.org Subject: Re: [WISPA] Another Ubiquity question On Wed, Oct 17, 2012 at 10:14:03PM -0400, Justin Wilson wrote: Many UBNT deployments running at 27volts of clean DC power. Not saying it's ideal but it works. 27v at the ethernet port or 27v at the base of the tower? -- Scott LambertKC5MLE Unix SysAdmin lamb...@lambertfam.org ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless
Re: [WISPA] Another Ubiquity question
The volt meter is a load, though. On 10/18/2012 2:57 PM, Chris Fabien wrote: No current = no voltage drop. Ohms Law. On Thu, Oct 18, 2012 at 3:38 PM, Jeromie Reeves jree...@18-30chat.net wrote: The resistance of the length of wire. On Thu, Oct 18, 2012 at 11:03 AM, Greg Ihnen os10ru...@gmail.com wrote: A voltage difference with no load? What's causing the drop? On Thu, Oct 18, 2012 at 10:06 AM, Justin Wilson li...@mtin.net wrote: We see 27.3 volts at the battery. And 27.1 volts at the top with no load. Obviously load will have an impact on this. Justin -Original Message- From: Jeromie Reeves jree...@18-30chat.net Reply-To: WISPA General List wireless@wispa.org Date: Thursday, October 18, 2012 9:15 AM To: WISPA General List wireless@wispa.org Subject: Re: [WISPA] Another Ubiquity question That depends on wire size. That distance is not going to be ethernet so I will assume #12 AWG, 400ft, copper wire, etc. You should be seeing a 5.6% drop under a 1amp load or about 25v under load. On Thu, Oct 18, 2012 at 6:02 AM, Justin Wilson li...@mtin.net wrote: 27 volts at the base. DC has very little loss over 400-500 foot distances. We are seeing about .1 volt loss on a 400 foot run. -Original Message- From: Scott Lambert lamb...@lambertfam.org Reply-To: WISPA General List wireless@wispa.org Date: Thursday, October 18, 2012 12:16 AM To: wireless@wispa.org Subject: Re: [WISPA] Another Ubiquity question On Wed, Oct 17, 2012 at 10:14:03PM -0400, Justin Wilson wrote: Many UBNT deployments running at 27volts of clean DC power. Not saying it's ideal but it works. 27v at the ethernet port or 27v at the base of the tower? -- Scott LambertKC5MLE Unix SysAdmin lamb...@lambertfam.org ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless
Re: [WISPA] Another Ubiquity question
Volt meters are typically very high input impedance, 1 Mohm or more, so that they don't have any effect on the circuit when testing. On Thu, Oct 18, 2012 at 4:18 PM, Mike Mattox wi...@mcmsys.com wrote: The volt meter is a load, though. On 10/18/2012 2:57 PM, Chris Fabien wrote: No current = no voltage drop. Ohms Law. On Thu, Oct 18, 2012 at 3:38 PM, Jeromie Reeves jree...@18-30chat.net wrote: The resistance of the length of wire. On Thu, Oct 18, 2012 at 11:03 AM, Greg Ihnen os10ru...@gmail.com wrote: A voltage difference with no load? What's causing the drop? On Thu, Oct 18, 2012 at 10:06 AM, Justin Wilson li...@mtin.net wrote: We see 27.3 volts at the battery. And 27.1 volts at the top with no load. Obviously load will have an impact on this. Justin -Original Message- From: Jeromie Reeves jree...@18-30chat.net Reply-To: WISPA General List wireless@wispa.org Date: Thursday, October 18, 2012 9:15 AM To: WISPA General List wireless@wispa.org Subject: Re: [WISPA] Another Ubiquity question That depends on wire size. That distance is not going to be ethernet so I will assume #12 AWG, 400ft, copper wire, etc. You should be seeing a 5.6% drop under a 1amp load or about 25v under load. On Thu, Oct 18, 2012 at 6:02 AM, Justin Wilson li...@mtin.net wrote: 27 volts at the base. DC has very little loss over 400-500 foot distances. We are seeing about .1 volt loss on a 400 foot run. -Original Message- From: Scott Lambert lamb...@lambertfam.org Reply-To: WISPA General List wireless@wispa.org Date: Thursday, October 18, 2012 12:16 AM To: wireless@wispa.org Subject: Re: [WISPA] Another Ubiquity question On Wed, Oct 17, 2012 at 10:14:03PM -0400, Justin Wilson wrote: Many UBNT deployments running at 27volts of clean DC power. Not saying it's ideal but it works. 27v at the ethernet port or 27v at the base of the tower? -- Scott LambertKC5MLE Unix SysAdmin lamb...@lambertfam.org ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless
Re: [WISPA] Another Ubiquity question
That's what I thought... but... he said: We see 27.3 volts at the battery. And 27.1 volts at the top with no load On Thu, Oct 18, 2012 at 3:57 PM, Chris Fabien ch...@lakenetmi.com wrote: No current = no voltage drop. Ohms Law. On Thu, Oct 18, 2012 at 3:38 PM, Jeromie Reeves jree...@18-30chat.net wrote: The resistance of the length of wire. On Thu, Oct 18, 2012 at 11:03 AM, Greg Ihnen os10ru...@gmail.com wrote: A voltage difference with no load? What's causing the drop? On Thu, Oct 18, 2012 at 10:06 AM, Justin Wilson li...@mtin.net wrote: We see 27.3 volts at the battery. And 27.1 volts at the top with no load. Obviously load will have an impact on this. Justin -Original Message- From: Jeromie Reeves jree...@18-30chat.net Reply-To: WISPA General List wireless@wispa.org Date: Thursday, October 18, 2012 9:15 AM To: WISPA General List wireless@wispa.org Subject: Re: [WISPA] Another Ubiquity question That depends on wire size. That distance is not going to be ethernet so I will assume #12 AWG, 400ft, copper wire, etc. You should be seeing a 5.6% drop under a 1amp load or about 25v under load. On Thu, Oct 18, 2012 at 6:02 AM, Justin Wilson li...@mtin.net wrote: 27 volts at the base. DC has very little loss over 400-500 foot distances. We are seeing about .1 volt loss on a 400 foot run. -Original Message- From: Scott Lambert lamb...@lambertfam.org Reply-To: WISPA General List wireless@wispa.org Date: Thursday, October 18, 2012 12:16 AM To: wireless@wispa.org Subject: Re: [WISPA] Another Ubiquity question On Wed, Oct 17, 2012 at 10:14:03PM -0400, Justin Wilson wrote: Many UBNT deployments running at 27volts of clean DC power. Not saying it's ideal but it works. 27v at the ethernet port or 27v at the base of the tower? -- Scott LambertKC5MLE Unix SysAdmin lamb...@lambertfam.org ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless
Re: [WISPA] Another Ubiquity question
Megaohms though, probably 30 MOhms or more. It's negligible. On Thu, Oct 18, 2012 at 4:18 PM, Mike Mattox wi...@mcmsys.com wrote: The volt meter is a load, though. On 10/18/2012 2:57 PM, Chris Fabien wrote: No current = no voltage drop. Ohms Law. On Thu, Oct 18, 2012 at 3:38 PM, Jeromie Reeves jree...@18-30chat.net wrote: The resistance of the length of wire. On Thu, Oct 18, 2012 at 11:03 AM, Greg Ihnen os10ru...@gmail.com wrote: A voltage difference with no load? What's causing the drop? On Thu, Oct 18, 2012 at 10:06 AM, Justin Wilson li...@mtin.net wrote: We see 27.3 volts at the battery. And 27.1 volts at the top with no load. Obviously load will have an impact on this. Justin -Original Message- From: Jeromie Reeves jree...@18-30chat.net Reply-To: WISPA General List wireless@wispa.org Date: Thursday, October 18, 2012 9:15 AM To: WISPA General List wireless@wispa.org Subject: Re: [WISPA] Another Ubiquity question That depends on wire size. That distance is not going to be ethernet so I will assume #12 AWG, 400ft, copper wire, etc. You should be seeing a 5.6% drop under a 1amp load or about 25v under load. On Thu, Oct 18, 2012 at 6:02 AM, Justin Wilson li...@mtin.net wrote: 27 volts at the base. DC has very little loss over 400-500 foot distances. We are seeing about .1 volt loss on a 400 foot run. -Original Message- From: Scott Lambert lamb...@lambertfam.org Reply-To: WISPA General List wireless@wispa.org Date: Thursday, October 18, 2012 12:16 AM To: wireless@wispa.org Subject: Re: [WISPA] Another Ubiquity question On Wed, Oct 17, 2012 at 10:14:03PM -0400, Justin Wilson wrote: Many UBNT deployments running at 27volts of clean DC power. Not saying it's ideal but it works. 27v at the ethernet port or 27v at the base of the tower? -- Scott LambertKC5MLE Unix SysAdmin lamb...@lambertfam.org ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless
Re: [WISPA] Another Ubiquity question
Doesn't UBNT gear take up to 30v? Greg On Mon, Oct 15, 2012 at 4:22 PM, Jeromie Reeves jree...@18-30chat.netwrote: Why not run the NSM5 on 24v? Just add a diode or two to the + side, the 1v drop on them will protect the NSM from the charge voltage of the bank. $2 fix On Mon, Oct 15, 2012 at 10:44 AM, Olufemi Adalemo adal...@gmail.com wrote: It just dawned on me that I may have been barking up the wrong tree I only have the one NSM5 to connect, I could hook this up to the parallel segment of my battery bank and get only 12v while the rest of the installation that's connected in series gets 24v. Do you think this will work? Don't really have to worry about the NSM5 running down the battery cause load is low and the cable run is under 10m so the voltage drop from 12v will be negligible So this is how it would be: 24v solar panel connected to 24v charge controller with 4 x 12v batteries connected in a 2x2 series/parallel array. cable connected to the parallel segment of battery bank (theoretically giving 12v to the NSM5), rest of the load connected to the charge controller at 24v What do you think? - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 8:18 PM, Kristian Hoffmann kh...@fire2wire.com wrote: Ya, it should be +24 on pins 4,5 and -24/comm on 7,8. If it blew up then there was probably a short somewhere. -Kristian On 10/12/2012 11:11 AM, Olufemi Adalemo wrote: Ah ok, it is possible that the guys didn't get the polarity right I will check though they swear that they did - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 7:05 PM, Josh Luthman j...@imaginenetworksllc.com wrote: What voltage were the batteries spitting out? They charge at 27v but without a charger put out much closer to 24v until they begin discharging. If it fried the radio I would first think that it was connected wrong, not that the voltage was too high. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 2:02 PM, Olufemi Adalemo adal...@gmail.com wrote: What's your typical config for the NSM5? Some of my guys just tried to power one off a 24v battery bank (no charger connected just battery) and it fried good - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 6:56 PM, Kristian Hoffmann kh...@fire2wire.com wrote: We have MT and Ubnt equipment of all shapes and sizes running at 27.6V. The only problems we've had are a handful of freak RB411s that won't power on with 27V. Most of the older ones wouldn't kick into overvoltage protection until 28V, but we've come across a few odd balls. -Kristian On 10/12/2012 10:44 AM, Josh Luthman wrote: Charger isn't going to spit out 24v for batteries that need charged, it's usually 27v. I was under the impression they would simply lock up and you could reboot, or maybe I'm just thinking of MT. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 10:08 PM, Olufemi Adalemo adal...@gmail.com wrote: Aha, thanks That explains why I have a dead NSM5 on my desk I guess the charge controller is not very good at giving out 24v regulated power - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 6:17 PM, Josh Luthman j...@imaginenetworksllc.com wrote: Yes you will. The batteries will probably be around 27v which Ubnt won't like. You'll need to clean the ~18-27v from the batteries to 24v. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 1:14 PM, Olufemi Adalemo adal...@gmail.com wrote: Need help, I'm looking to deploy a UBNT NSM5 powered by a 24v solar supply. Does anyone have experience with this? The data sheet shows that it requires a 24v supply however the POE injector supplied is 15v, do I need a DC to DC converter? Best regards, - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org
Re: [WISPA] Another Ubiquity question
II was told NO!! 27VDC Steve Barnes General Manager PCS-WIN / RC-WiFihttp://www.rcwifi.com/ From: wireless-boun...@wispa.org [mailto:wireless-boun...@wispa.org] On Behalf Of Greg Ihnen Sent: Wednesday, October 17, 2012 7:35 AM To: WISPA General List Subject: Re: [WISPA] Another Ubiquity question Doesn't UBNT gear take up to 30v? Greg On Mon, Oct 15, 2012 at 4:22 PM, Jeromie Reeves jree...@18-30chat.netmailto:jree...@18-30chat.net wrote: Why not run the NSM5 on 24v? Just add a diode or two to the + side, the 1v drop on them will protect the NSM from the charge voltage of the bank. $2 fix On Mon, Oct 15, 2012 at 10:44 AM, Olufemi Adalemo adal...@gmail.commailto:adal...@gmail.com wrote: It just dawned on me that I may have been barking up the wrong tree I only have the one NSM5 to connect, I could hook this up to the parallel segment of my battery bank and get only 12v while the rest of the installation that's connected in series gets 24v. Do you think this will work? Don't really have to worry about the NSM5 running down the battery cause load is low and the cable run is under 10m so the voltage drop from 12v will be negligible So this is how it would be: 24v solar panel connected to 24v charge controller with 4 x 12v batteries connected in a 2x2 series/parallel array. cable connected to the parallel segment of battery bank (theoretically giving 12v to the NSM5), rest of the load connected to the charge controller at 24v What do you think? - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.commailto:f...@adalemo.com On Fri, Oct 12, 2012 at 8:18 PM, Kristian Hoffmann kh...@fire2wire.commailto:kh...@fire2wire.com wrote: Ya, it should be +24 on pins 4,5 and -24/comm on 7,8. If it blew up then there was probably a short somewhere. -Kristian On 10/12/2012 11:11 AM, Olufemi Adalemo wrote: Ah ok, it is possible that the guys didn't get the polarity right I will check though they swear that they did - - - Olufemi Adalemo M: +234-803-5610040tel:%2B234-803-5610040 M: +234-809-8610040tel:%2B234-809-8610040 f...@adalemo.commailto:f...@adalemo.com On Fri, Oct 12, 2012 at 7:05 PM, Josh Luthman j...@imaginenetworksllc.commailto:j...@imaginenetworksllc.com wrote: What voltage were the batteries spitting out? They charge at 27v but without a charger put out much closer to 24v until they begin discharging. If it fried the radio I would first think that it was connected wrong, not that the voltage was too high. Josh Luthman Office: 937-552-2340tel:937-552-2340 Direct: 937-552-2343tel:937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 2:02 PM, Olufemi Adalemo adal...@gmail.commailto:adal...@gmail.com wrote: What's your typical config for the NSM5? Some of my guys just tried to power one off a 24v battery bank (no charger connected just battery) and it fried good - - - Olufemi Adalemo M: +234-803-5610040tel:%2B234-803-5610040 M: +234-809-8610040tel:%2B234-809-8610040 f...@adalemo.commailto:f...@adalemo.com On Fri, Oct 12, 2012 at 6:56 PM, Kristian Hoffmann kh...@fire2wire.commailto:kh...@fire2wire.com wrote: We have MT and Ubnt equipment of all shapes and sizes running at 27.6V. The only problems we've had are a handful of freak RB411s that won't power on with 27V. Most of the older ones wouldn't kick into overvoltage protection until 28V, but we've come across a few odd balls. -Kristian On 10/12/2012 10:44 AM, Josh Luthman wrote: Charger isn't going to spit out 24v for batteries that need charged, it's usually 27v. I was under the impression they would simply lock up and you could reboot, or maybe I'm just thinking of MT. Josh Luthman Office: 937-552-2340tel:937-552-2340 Direct: 937-552-2343tel:937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 10:08 PM, Olufemi Adalemo adal...@gmail.commailto:adal...@gmail.com wrote: Aha, thanks That explains why I have a dead NSM5 on my desk I guess the charge controller is not very good at giving out 24v regulated power - - - Olufemi Adalemo M: +234-803-5610040tel:%2B234-803-5610040 M: +234-809-8610040tel:%2B234-809-8610040 f...@adalemo.commailto:f...@adalemo.com On Fri, Oct 12, 2012 at 6:17 PM, Josh Luthman j...@imaginenetworksllc.commailto:j...@imaginenetworksllc.com wrote: Yes you will. The batteries will probably be around 27v which Ubnt won't like. You'll need to clean the ~18-27v from the batteries to 24v. Josh Luthman Office: 937-552-2340tel:937-552-2340 Direct: 937-552-2343tel:937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 1:14 PM, Olufemi Adalemo adal...@gmail.commailto:adal...@gmail.com wrote: Need help, I'm looking to deploy a UBNT NSM5 powered by a 24v solar supply. Does anyone have experience with this? The data sheet shows that it requires a 24v supply however the POE injector supplied is 15v, do I need
Re: [WISPA] Another Ubiquity question
Most definitely not 30v. I was warned and have it hammered down to not hit 27v or higher. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Wed, Oct 17, 2012 at 9:50 AM, Steve Barnes st...@pcswin.com wrote: II was told NO!! 27VDC ** ** Steve Barnes General Manager PCS-WIN / RC-WiFi http://www.rcwifi.com/ ** ** *From:* wireless-boun...@wispa.org [mailto:wireless-boun...@wispa.org] *On Behalf Of *Greg Ihnen *Sent:* Wednesday, October 17, 2012 7:35 AM *To:* WISPA General List *Subject:* Re: [WISPA] Another Ubiquity question ** ** Doesn't UBNT gear take up to 30v? ** ** Greg On Mon, Oct 15, 2012 at 4:22 PM, Jeromie Reeves jree...@18-30chat.net wrote: Why not run the NSM5 on 24v? Just add a diode or two to the + side, the 1v drop on them will protect the NSM from the charge voltage of the bank. $2 fix On Mon, Oct 15, 2012 at 10:44 AM, Olufemi Adalemo adal...@gmail.com wrote: It just dawned on me that I may have been barking up the wrong tree I only have the one NSM5 to connect, I could hook this up to the parallel segment of my battery bank and get only 12v while the rest of the installation that's connected in series gets 24v. Do you think this will work? Don't really have to worry about the NSM5 running down the battery cause load is low and the cable run is under 10m so the voltage drop from 12v will be negligible So this is how it would be: 24v solar panel connected to 24v charge controller with 4 x 12v batteries connected in a 2x2 series/parallel array. cable connected to the parallel segment of battery bank (theoretically giving 12v to the NSM5), rest of the load connected to the charge controller at 24v What do you think? - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 8:18 PM, Kristian Hoffmann kh...@fire2wire.com wrote: Ya, it should be +24 on pins 4,5 and -24/comm on 7,8. If it blew up then there was probably a short somewhere. -Kristian On 10/12/2012 11:11 AM, Olufemi Adalemo wrote: Ah ok, it is possible that the guys didn't get the polarity right I will check though they swear that they did - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 7:05 PM, Josh Luthman j...@imaginenetworksllc.com wrote: What voltage were the batteries spitting out? They charge at 27v but without a charger put out much closer to 24v until they begin discharging. If it fried the radio I would first think that it was connected wrong, not that the voltage was too high. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 2:02 PM, Olufemi Adalemo adal...@gmail.com wrote: What's your typical config for the NSM5? Some of my guys just tried to power one off a 24v battery bank (no charger connected just battery) and it fried good - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 6:56 PM, Kristian Hoffmann kh...@fire2wire.com wrote: We have MT and Ubnt equipment of all shapes and sizes running at 27.6V. The only problems we've had are a handful of freak RB411s that won't power on with 27V. Most of the older ones wouldn't kick into overvoltage protection until 28V, but we've come across a few odd balls. -Kristian On 10/12/2012 10:44 AM, Josh Luthman wrote: Charger isn't going to spit out 24v for batteries that need charged, it's usually 27v. I was under the impression they would simply lock up and you could reboot, or maybe I'm just thinking of MT. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 10:08 PM, Olufemi Adalemo adal...@gmail.com wrote: Aha, thanks That explains why I have a dead NSM5 on my desk I guess the charge controller is not very good at giving out 24v regulated power - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 6:17 PM, Josh Luthman j...@imaginenetworksllc.com wrote: Yes you will. The batteries will probably be around 27v which Ubnt won't like. You'll need to clean the ~18-27v from the batteries to 24v. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 1:14 PM, Olufemi Adalemo adal...@gmail.com wrote: Need help, I'm looking to deploy a UBNT NSM5 powered by a 24v solar supply. Does anyone have experience with this? The data sheet shows that it requires a 24v supply however the POE injector supplied is 15v, do I need a DC to DC converter? Best regards, - - - Olufemi
Re: [WISPA] Another Ubiquity question
OK, I asked about the PS2 years back and I believe I was told 30v for that. Greg On Wed, Oct 17, 2012 at 9:50 AM, Steve Barnes st...@pcswin.com wrote: II was told NO!! 27VDC ** ** Steve Barnes General Manager PCS-WIN / RC-WiFi http://www.rcwifi.com/ ** ** *From:* wireless-boun...@wispa.org [mailto:wireless-boun...@wispa.org] *On Behalf Of *Greg Ihnen *Sent:* Wednesday, October 17, 2012 7:35 AM *To:* WISPA General List *Subject:* Re: [WISPA] Another Ubiquity question ** ** Doesn't UBNT gear take up to 30v? ** ** Greg On Mon, Oct 15, 2012 at 4:22 PM, Jeromie Reeves jree...@18-30chat.net wrote: Why not run the NSM5 on 24v? Just add a diode or two to the + side, the 1v drop on them will protect the NSM from the charge voltage of the bank. $2 fix On Mon, Oct 15, 2012 at 10:44 AM, Olufemi Adalemo adal...@gmail.com wrote: It just dawned on me that I may have been barking up the wrong tree I only have the one NSM5 to connect, I could hook this up to the parallel segment of my battery bank and get only 12v while the rest of the installation that's connected in series gets 24v. Do you think this will work? Don't really have to worry about the NSM5 running down the battery cause load is low and the cable run is under 10m so the voltage drop from 12v will be negligible So this is how it would be: 24v solar panel connected to 24v charge controller with 4 x 12v batteries connected in a 2x2 series/parallel array. cable connected to the parallel segment of battery bank (theoretically giving 12v to the NSM5), rest of the load connected to the charge controller at 24v What do you think? - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 8:18 PM, Kristian Hoffmann kh...@fire2wire.com wrote: Ya, it should be +24 on pins 4,5 and -24/comm on 7,8. If it blew up then there was probably a short somewhere. -Kristian On 10/12/2012 11:11 AM, Olufemi Adalemo wrote: Ah ok, it is possible that the guys didn't get the polarity right I will check though they swear that they did - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 7:05 PM, Josh Luthman j...@imaginenetworksllc.com wrote: What voltage were the batteries spitting out? They charge at 27v but without a charger put out much closer to 24v until they begin discharging. If it fried the radio I would first think that it was connected wrong, not that the voltage was too high. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 2:02 PM, Olufemi Adalemo adal...@gmail.com wrote: What's your typical config for the NSM5? Some of my guys just tried to power one off a 24v battery bank (no charger connected just battery) and it fried good - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 6:56 PM, Kristian Hoffmann kh...@fire2wire.com wrote: We have MT and Ubnt equipment of all shapes and sizes running at 27.6V. The only problems we've had are a handful of freak RB411s that won't power on with 27V. Most of the older ones wouldn't kick into overvoltage protection until 28V, but we've come across a few odd balls. -Kristian On 10/12/2012 10:44 AM, Josh Luthman wrote: Charger isn't going to spit out 24v for batteries that need charged, it's usually 27v. I was under the impression they would simply lock up and you could reboot, or maybe I'm just thinking of MT. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 10:08 PM, Olufemi Adalemo adal...@gmail.com wrote: Aha, thanks That explains why I have a dead NSM5 on my desk I guess the charge controller is not very good at giving out 24v regulated power - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 6:17 PM, Josh Luthman j...@imaginenetworksllc.com wrote: Yes you will. The batteries will probably be around 27v which Ubnt won't like. You'll need to clean the ~18-27v from the batteries to 24v. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 1:14 PM, Olufemi Adalemo adal...@gmail.com wrote: Need help, I'm looking to deploy a UBNT NSM5 powered by a 24v solar supply. Does anyone have experience with this? The data sheet shows that it requires a 24v supply however the POE injector supplied is 15v, do I need a DC to DC converter? Best regards, - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com
Re: [WISPA] Another Ubiquity question
That is odd. I have no idea why it would get so hot unless the current passing it was significant. This was a schottky or a power diode right, not a zener? Most zeners will not take the current. On Mon, Oct 15, 2012 at 2:04 PM, Josh Luthman j...@imaginenetworksllc.com wrote: Between the regulator and load. On Oct 15, 2012 5:01 PM, Jeromie Reeves jree...@18-30chat.net wrote: Where did you put that diode? I have done this and at the low power that is needed they do not get noticeably warm at all. On Mon, Oct 15, 2012 at 1:38 PM, Josh Luthman j...@imaginenetworksllc.com wrote: I tried that method. Diode got hotter than hell. Burnt right through the insulation I covered it with (and since it was bent the jacket came right off). Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Mon, Oct 15, 2012 at 4:22 PM, Jeromie Reeves jree...@18-30chat.net wrote: Why not run the NSM5 on 24v? Just add a diode or two to the + side, the 1v drop on them will protect the NSM from the charge voltage of the bank. $2 fix On Mon, Oct 15, 2012 at 10:44 AM, Olufemi Adalemo adal...@gmail.com wrote: It just dawned on me that I may have been barking up the wrong tree I only have the one NSM5 to connect, I could hook this up to the parallel segment of my battery bank and get only 12v while the rest of the installation that's connected in series gets 24v. Do you think this will work? Don't really have to worry about the NSM5 running down the battery cause load is low and the cable run is under 10m so the voltage drop from 12v will be negligible So this is how it would be: 24v solar panel connected to 24v charge controller with 4 x 12v batteries connected in a 2x2 series/parallel array. cable connected to the parallel segment of battery bank (theoretically giving 12v to the NSM5), rest of the load connected to the charge controller at 24v What do you think? - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 8:18 PM, Kristian Hoffmann kh...@fire2wire.com wrote: Ya, it should be +24 on pins 4,5 and -24/comm on 7,8. If it blew up then there was probably a short somewhere. -Kristian On 10/12/2012 11:11 AM, Olufemi Adalemo wrote: Ah ok, it is possible that the guys didn't get the polarity right I will check though they swear that they did - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 7:05 PM, Josh Luthman j...@imaginenetworksllc.com wrote: What voltage were the batteries spitting out? They charge at 27v but without a charger put out much closer to 24v until they begin discharging. If it fried the radio I would first think that it was connected wrong, not that the voltage was too high. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 2:02 PM, Olufemi Adalemo adal...@gmail.com wrote: What's your typical config for the NSM5? Some of my guys just tried to power one off a 24v battery bank (no charger connected just battery) and it fried good - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 6:56 PM, Kristian Hoffmann kh...@fire2wire.com wrote: We have MT and Ubnt equipment of all shapes and sizes running at 27.6V. The only problems we've had are a handful of freak RB411s that won't power on with 27V. Most of the older ones wouldn't kick into overvoltage protection until 28V, but we've come across a few odd balls. -Kristian On 10/12/2012 10:44 AM, Josh Luthman wrote: Charger isn't going to spit out 24v for batteries that need charged, it's usually 27v. I was under the impression they would simply lock up and you could reboot, or maybe I'm just thinking of MT. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 10:08 PM, Olufemi Adalemo adal...@gmail.com wrote: Aha, thanks That explains why I have a dead NSM5 on my desk I guess the charge controller is not very good at giving out 24v regulated power - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 6:17 PM, Josh Luthman j...@imaginenetworksllc.com wrote: Yes you will. The batteries will probably be around 27v which Ubnt won't like. You'll need to clean the ~18-27v from the batteries to 24v. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337
Re: [WISPA] Another Ubiquity question
I have this on my wall. Never used it. Nice to have. On Oct 17, 2012 11:32 AM, Faisal Imtiaz fai...@snappydsl.net wrote: This is an older document.. but it should help Faisal Imtiaz Snappy Internet Telecom 7266 SW 48 Street Miami, Fl 33155 Tel: 305 663 5518 x 232 Helpdesk: 305 663 5518 option 2 Email: supp...@snappydsl.net On 10/17/2012 10:59 AM, Greg Ihnen wrote: OK, I asked about the PS2 years back and I believe I was told 30v for that. Greg On Wed, Oct 17, 2012 at 9:50 AM, Steve Barnes st...@pcswin.com wrote: II was told NO!! 27VDC Steve Barnes General Manager PCS-WIN / RC-WiFi http://www.rcwifi.com/ *From:* wireless-boun...@wispa.org [mailto:wireless-boun...@wispa.org] *On Behalf Of *Greg Ihnen *Sent:* Wednesday, October 17, 2012 7:35 AM *To:* WISPA General List *Subject:* Re: [WISPA] Another Ubiquity question Doesn't UBNT gear take up to 30v? Greg On Mon, Oct 15, 2012 at 4:22 PM, Jeromie Reeves jree...@18-30chat.net wrote: Why not run the NSM5 on 24v? Just add a diode or two to the + side, the 1v drop on them will protect the NSM from the charge voltage of the bank. $2 fix On Mon, Oct 15, 2012 at 10:44 AM, Olufemi Adalemo adal...@gmail.com wrote: It just dawned on me that I may have been barking up the wrong tree I only have the one NSM5 to connect, I could hook this up to the parallel segment of my battery bank and get only 12v while the rest of the installation that's connected in series gets 24v. Do you think this will work? Don't really have to worry about the NSM5 running down the battery cause load is low and the cable run is under 10m so the voltage drop from 12v will be negligible So this is how it would be: 24v solar panel connected to 24v charge controller with 4 x 12v batteries connected in a 2x2 series/parallel array. cable connected to the parallel segment of battery bank (theoretically giving 12v to the NSM5), rest of the load connected to the charge controller at 24v What do you think? - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 8:18 PM, Kristian Hoffmann kh...@fire2wire.com wrote: Ya, it should be +24 on pins 4,5 and -24/comm on 7,8. If it blew up then there was probably a short somewhere. -Kristian On 10/12/2012 11:11 AM, Olufemi Adalemo wrote: Ah ok, it is possible that the guys didn't get the polarity right I will check though they swear that they did - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 7:05 PM, Josh Luthman j...@imaginenetworksllc.com wrote: What voltage were the batteries spitting out? They charge at 27v but without a charger put out much closer to 24v until they begin discharging. If it fried the radio I would first think that it was connected wrong, not that the voltage was too high. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 2:02 PM, Olufemi Adalemo adal...@gmail.com wrote: What's your typical config for the NSM5? Some of my guys just tried to power one off a 24v battery bank (no charger connected just battery) and it fried good - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 6:56 PM, Kristian Hoffmann kh...@fire2wire.com wrote: We have MT and Ubnt equipment of all shapes and sizes running at 27.6V. The only problems we've had are a handful of freak RB411s that won't power on with 27V. Most of the older ones wouldn't kick into overvoltage protection until 28V, but we've come across a few odd balls. -Kristian On 10/12/2012 10:44 AM, Josh Luthman wrote: Charger isn't going to spit out 24v for batteries that need charged, it's usually 27v. I was under the impression they would simply lock up and you could reboot, or maybe I'm just thinking of MT. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 10:08 PM, Olufemi Adalemo adal...@gmail.com wrote: Aha, thanks That explains why I have a dead NSM5 on my desk I guess the charge controller is not very good at giving out 24v regulated power - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 6:17 PM, Josh Luthman j...@imaginenetworksllc.com wrote: Yes you will. The batteries will probably be around 27v which Ubnt won't like. You'll need to clean the ~18-27v from the batteries to 24v. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 1:14 PM, Olufemi Adalemo adal...@gmail.com wrote: Need help, I'm looking to deploy a UBNT NSM5
Re: [WISPA] Another Ubiquity question
Can I ask that you all please move this over to the UBNT list? Thanks, -d On Wed, Oct 17, 2012 at 10:36 AM, Josh Luthman j...@imaginenetworksllc.comwrote: I have this on my wall. Never used it. Nice to have. On Oct 17, 2012 11:32 AM, Faisal Imtiaz fai...@snappydsl.net wrote: This is an older document.. but it should help Faisal Imtiaz Snappy Internet Telecom 7266 SW 48 Street Miami, Fl 33155 Tel: 305 663 5518 x 232 Helpdesk: 305 663 5518 option 2 Email: supp...@snappydsl.net On 10/17/2012 10:59 AM, Greg Ihnen wrote: OK, I asked about the PS2 years back and I believe I was told 30v for that. Greg On Wed, Oct 17, 2012 at 9:50 AM, Steve Barnes st...@pcswin.com wrote: II was told NO!! 27VDC Steve Barnes General Manager PCS-WIN / RC-WiFi http://www.rcwifi.com/ *From:* wireless-boun...@wispa.org [mailto:wireless-boun...@wispa.org] *On Behalf Of *Greg Ihnen *Sent:* Wednesday, October 17, 2012 7:35 AM *To:* WISPA General List *Subject:* Re: [WISPA] Another Ubiquity question Doesn't UBNT gear take up to 30v? Greg On Mon, Oct 15, 2012 at 4:22 PM, Jeromie Reeves jree...@18-30chat.net wrote: Why not run the NSM5 on 24v? Just add a diode or two to the + side, the 1v drop on them will protect the NSM from the charge voltage of the bank. $2 fix On Mon, Oct 15, 2012 at 10:44 AM, Olufemi Adalemo adal...@gmail.com wrote: It just dawned on me that I may have been barking up the wrong tree I only have the one NSM5 to connect, I could hook this up to the parallel segment of my battery bank and get only 12v while the rest of the installation that's connected in series gets 24v. Do you think this will work? Don't really have to worry about the NSM5 running down the battery cause load is low and the cable run is under 10m so the voltage drop from 12v will be negligible So this is how it would be: 24v solar panel connected to 24v charge controller with 4 x 12v batteries connected in a 2x2 series/parallel array. cable connected to the parallel segment of battery bank (theoretically giving 12v to the NSM5), rest of the load connected to the charge controller at 24v What do you think? - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 8:18 PM, Kristian Hoffmann kh...@fire2wire.com wrote: Ya, it should be +24 on pins 4,5 and -24/comm on 7,8. If it blew up then there was probably a short somewhere. -Kristian On 10/12/2012 11:11 AM, Olufemi Adalemo wrote: Ah ok, it is possible that the guys didn't get the polarity right I will check though they swear that they did - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 7:05 PM, Josh Luthman j...@imaginenetworksllc.com wrote: What voltage were the batteries spitting out? They charge at 27v but without a charger put out much closer to 24v until they begin discharging. If it fried the radio I would first think that it was connected wrong, not that the voltage was too high. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 2:02 PM, Olufemi Adalemo adal...@gmail.com wrote: What's your typical config for the NSM5? Some of my guys just tried to power one off a 24v battery bank (no charger connected just battery) and it fried good - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 6:56 PM, Kristian Hoffmann kh...@fire2wire.com wrote: We have MT and Ubnt equipment of all shapes and sizes running at 27.6V. The only problems we've had are a handful of freak RB411s that won't power on with 27V. Most of the older ones wouldn't kick into overvoltage protection until 28V, but we've come across a few odd balls. -Kristian On 10/12/2012 10:44 AM, Josh Luthman wrote: Charger isn't going to spit out 24v for batteries that need charged, it's usually 27v. I was under the impression they would simply lock up and you could reboot, or maybe I'm just thinking of MT. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 10:08 PM, Olufemi Adalemo adal...@gmail.com wrote: Aha, thanks That explains why I have a dead NSM5 on my desk I guess the charge controller is not very good at giving out 24v regulated power - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 6:17 PM, Josh Luthman j...@imaginenetworksllc.com wrote: Yes you will. The batteries will probably be around 27v which Ubnt won't like. You'll need to clean the ~18-27v from the batteries to 24v. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St
Re: [WISPA] Another Ubiquity question
The diode thing works fine IF you use the right diodes. For running a UBNT 24V device off a 24V battery floating on a charger, try 4x 1n4001 dioeds in series. will drop about 3V and carry 1A Works fine for me. That set of diodes will only carry one UBNT radio. Need a separate set for each radio. On 10/15/2012 4:38 PM, Josh Luthman wrote: I tried that method. Diode got hotter than hell. Burnt right through the insulation I covered it with (and since it was bent the jacket came right off). Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Mon, Oct 15, 2012 at 4:22 PM, Jeromie Reeves jree...@18-30chat.net wrote: Why not run the NSM5 on 24v? Just add a diode or two to the + side, the 1v drop on them will protect the NSM from the charge voltage of the bank. $2 fix On Mon, Oct 15, 2012 at 10:44 AM, Olufemi Adalemo adal...@gmail.com wrote: It just dawned on me that I may have been barking up the wrong tree I only have the one NSM5 to connect, I could hook this up to the parallel segment of my battery bank and get only 12v while the rest of the installation that's connected in series gets 24v. Do you think this will work? Don't really have to worry about the NSM5 running down the battery cause load is low and the cable run is under 10m so the voltage drop from 12v will be negligible So this is how it would be: 24v solar panel connected to 24v charge controller with 4 x 12v batteries connected in a 2x2 series/parallel array. cable connected to the parallel segment of battery bank (theoretically giving 12v to the NSM5), rest of the load connected to the charge controller at 24v What do you think? - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 8:18 PM, Kristian Hoffmann kh...@fire2wire.com wrote: Ya, it should be +24 on pins 4,5 and -24/comm on 7,8. If it blew up then there was probably a short somewhere. -Kristian On 10/12/2012 11:11 AM, Olufemi Adalemo wrote: Ah ok, it is possible that the guys didn't get the polarity right I will check though they swear that they did - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 7:05 PM, Josh Luthman j...@imaginenetworksllc.com wrote: What voltage were the batteries spitting out? They charge at 27v but without a charger put out much closer to 24v until they begin discharging. If it fried the radio I would first think that it was connected wrong, not that the voltage was too high. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 2:02 PM, Olufemi Adalemo adal...@gmail.com wrote: What's your typical config for the NSM5? Some of my guys just tried to power one off a 24v battery bank (no charger connected just battery) and it fried good - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 6:56 PM, Kristian Hoffmann
Re: [WISPA] Another Ubiquity question
Can you reveal your source? -Kristian On 10/17/2012 06:50 AM, Steve Barnes wrote: II was told NO!! 27VDC Steve Barnes General Manager PCS-WIN / RC-WiFi http://www.rcwifi.com/ *From:*wireless-boun...@wispa.org [mailto:wireless-boun...@wispa.org] *On Behalf Of *Greg Ihnen *Sent:* Wednesday, October 17, 2012 7:35 AM *To:* WISPA General List *Subject:* Re: [WISPA] Another Ubiquity question Doesn't UBNT gear take up to 30v? Greg On Mon, Oct 15, 2012 at 4:22 PM, Jeromie Reeves jree...@18-30chat.net mailto:jree...@18-30chat.net wrote: Why not run the NSM5 on 24v? Just add a diode or two to the + side, the 1v drop on them will protect the NSM from the charge voltage of the bank. $2 fix On Mon, Oct 15, 2012 at 10:44 AM, Olufemi Adalemo adal...@gmail.com mailto:adal...@gmail.com wrote: It just dawned on me that I may have been barking up the wrong tree I only have the one NSM5 to connect, I could hook this up to the parallel segment of my battery bank and get only 12v while the rest of the installation that's connected in series gets 24v. Do you think this will work? Don't really have to worry about the NSM5 running down the battery cause load is low and the cable run is under 10m so the voltage drop from 12v will be negligible So this is how it would be: 24v solar panel connected to 24v charge controller with 4 x 12v batteries connected in a 2x2 series/parallel array. cable connected to the parallel segment of battery bank (theoretically giving 12v to the NSM5), rest of the load connected to the charge controller at 24v What do you think? - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com mailto:f...@adalemo.com On Fri, Oct 12, 2012 at 8:18 PM, Kristian Hoffmann kh...@fire2wire.com mailto:kh...@fire2wire.com wrote: Ya, it should be +24 on pins 4,5 and -24/comm on 7,8. If it blew up then there was probably a short somewhere. -Kristian On 10/12/2012 11:11 AM, Olufemi Adalemo wrote: Ah ok, it is possible that the guys didn't get the polarity right I will check though they swear that they did - - - Olufemi Adalemo M: +234-803-5610040 tel:%2B234-803-5610040 M: +234-809-8610040 tel:%2B234-809-8610040 f...@adalemo.com mailto:f...@adalemo.com On Fri, Oct 12, 2012 at 7:05 PM, Josh Luthman j...@imaginenetworksllc.com mailto:j...@imaginenetworksllc.com wrote: What voltage were the batteries spitting out? They charge at 27v but without a charger put out much closer to 24v until they begin discharging. If it fried the radio I would first think that it was connected wrong, not that the voltage was too high. Josh Luthman Office: 937-552-2340 tel:937-552-2340 Direct: 937-552-2343 tel:937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 2:02 PM, Olufemi Adalemo adal...@gmail.com mailto:adal...@gmail.com wrote: What's your typical config for the NSM5? Some of my guys just tried to power one off a 24v battery bank (no charger connected just battery) and it fried good - - - Olufemi Adalemo M: +234-803-5610040 tel:%2B234-803-5610040 M: +234-809-8610040 tel:%2B234-809-8610040 f...@adalemo.com mailto:f...@adalemo.com On Fri, Oct 12, 2012 at 6:56 PM, Kristian Hoffmann kh...@fire2wire.com mailto:kh...@fire2wire.com wrote: We have MT and Ubnt equipment of all shapes and sizes running at 27.6V. The only problems we've had are a handful of freak RB411s that won't power on with 27V. Most of the older ones wouldn't kick into overvoltage protection until 28V, but we've come across a few odd balls. -Kristian On 10/12/2012 10:44 AM, Josh Luthman wrote: Charger isn't going to spit out 24v for batteries that need charged, it's usually 27v. I was under the impression they would simply lock up and you could reboot, or maybe I'm just thinking of MT. Josh Luthman Office: 937-552-2340 tel:937-552-2340 Direct: 937-552-2343 tel:937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 10:08 PM, Olufemi Adalemo adal...@gmail.com mailto:adal...@gmail.com wrote: Aha, thanks That explains why I have a dead NSM5 on my desk I guess the charge controller is not very good at giving out 24v regulated power - - - Olufemi Adalemo M: +234-803-5610040 tel:%2B234-803-5610040 M: +234-809-8610040 tel:%2B234-809-8610040 f...@adalemo.com mailto:f...@adalemo.com On Fri, Oct 12, 2012 at 6:17 PM, Josh Luthman j...@imaginenetworksllc.com mailto:j...@imaginenetworksllc.com wrote: Yes you will. The batteries will probably be around 27v which Ubnt won't like. You'll need to clean the ~18-27v from the batteries to 24v. Josh Luthman Office: 937-552-2340 tel:937-552-2340 Direct: 937-552-2343 tel:937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 1:14 PM, Olufemi Adalemo adal...@gmail.com mailto:adal...@gmail.com wrote: Need help, I'm looking to deploy a UBNT NSM5 powered by a 24v solar
Re: [WISPA] Another Ubiquity question
I believe it was Matt Hardy and Then was told the same when I went to AirMax Certification classes. Steve Barnes General Manager PCS-WIN / RC-WiFihttp://www.rcwifi.com/ From: wireless-boun...@wispa.org [mailto:wireless-boun...@wispa.org] On Behalf Of Kristian Hoffmann Sent: Wednesday, October 17, 2012 7:44 PM To: wireless@wispa.org Subject: Re: [WISPA] Another Ubiquity question Can you reveal your source? -Kristian On 10/17/2012 06:50 AM, Steve Barnes wrote: II was told NO!! 27VDC Steve Barnes General Manager PCS-WIN / RC-WiFihttp://www.rcwifi.com/ From: wireless-boun...@wispa.orgmailto:wireless-boun...@wispa.org [mailto:wireless-boun...@wispa.org] On Behalf Of Greg Ihnen Sent: Wednesday, October 17, 2012 7:35 AM To: WISPA General List Subject: Re: [WISPA] Another Ubiquity question Doesn't UBNT gear take up to 30v? Greg On Mon, Oct 15, 2012 at 4:22 PM, Jeromie Reeves jree...@18-30chat.netmailto:jree...@18-30chat.net wrote: Why not run the NSM5 on 24v? Just add a diode or two to the + side, the 1v drop on them will protect the NSM from the charge voltage of the bank. $2 fix On Mon, Oct 15, 2012 at 10:44 AM, Olufemi Adalemo adal...@gmail.commailto:adal...@gmail.com wrote: It just dawned on me that I may have been barking up the wrong tree I only have the one NSM5 to connect, I could hook this up to the parallel segment of my battery bank and get only 12v while the rest of the installation that's connected in series gets 24v. Do you think this will work? Don't really have to worry about the NSM5 running down the battery cause load is low and the cable run is under 10m so the voltage drop from 12v will be negligible So this is how it would be: 24v solar panel connected to 24v charge controller with 4 x 12v batteries connected in a 2x2 series/parallel array. cable connected to the parallel segment of battery bank (theoretically giving 12v to the NSM5), rest of the load connected to the charge controller at 24v What do you think? - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.commailto:f...@adalemo.com On Fri, Oct 12, 2012 at 8:18 PM, Kristian Hoffmann kh...@fire2wire.commailto:kh...@fire2wire.com wrote: Ya, it should be +24 on pins 4,5 and -24/comm on 7,8. If it blew up then there was probably a short somewhere. -Kristian On 10/12/2012 11:11 AM, Olufemi Adalemo wrote: Ah ok, it is possible that the guys didn't get the polarity right I will check though they swear that they did - - - Olufemi Adalemo M: +234-803-5610040tel:%2B234-803-5610040 M: +234-809-8610040tel:%2B234-809-8610040 f...@adalemo.commailto:f...@adalemo.com On Fri, Oct 12, 2012 at 7:05 PM, Josh Luthman j...@imaginenetworksllc.commailto:j...@imaginenetworksllc.com wrote: What voltage were the batteries spitting out? They charge at 27v but without a charger put out much closer to 24v until they begin discharging. If it fried the radio I would first think that it was connected wrong, not that the voltage was too high. Josh Luthman Office: 937-552-2340tel:937-552-2340 Direct: 937-552-2343tel:937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 2:02 PM, Olufemi Adalemo adal...@gmail.commailto:adal...@gmail.com wrote: What's your typical config for the NSM5? Some of my guys just tried to power one off a 24v battery bank (no charger connected just battery) and it fried good - - - Olufemi Adalemo M: +234-803-5610040tel:%2B234-803-5610040 M: +234-809-8610040tel:%2B234-809-8610040 f...@adalemo.commailto:f...@adalemo.com On Fri, Oct 12, 2012 at 6:56 PM, Kristian Hoffmann kh...@fire2wire.commailto:kh...@fire2wire.com wrote: We have MT and Ubnt equipment of all shapes and sizes running at 27.6V. The only problems we've had are a handful of freak RB411s that won't power on with 27V. Most of the older ones wouldn't kick into overvoltage protection until 28V, but we've come across a few odd balls. -Kristian On 10/12/2012 10:44 AM, Josh Luthman wrote: Charger isn't going to spit out 24v for batteries that need charged, it's usually 27v. I was under the impression they would simply lock up and you could reboot, or maybe I'm just thinking of MT. Josh Luthman Office: 937-552-2340tel:937-552-2340 Direct: 937-552-2343tel:937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 10:08 PM, Olufemi Adalemo adal...@gmail.commailto:adal...@gmail.com wrote: Aha, thanks That explains why I have a dead NSM5 on my desk I guess the charge controller is not very good at giving out 24v regulated power - - - Olufemi Adalemo M: +234-803-5610040tel:%2B234-803-5610040 M: +234-809-8610040tel:%2B234-809-8610040 f...@adalemo.commailto:f...@adalemo.com On Fri, Oct 12, 2012 at 6:17 PM, Josh Luthman j...@imaginenetworksllc.commailto:j...@imaginenetworksllc.com wrote: Yes you will. The batteries will probably be around 27v which Ubnt won't like. You'll need to clean
Re: [WISPA] Another Ubiquity question
The forums and Matt Hardy I believe will back this up. You'll fry at over 27 volts. Kristian Hoffmann kh...@fire2wire.com wrote: Can you reveal your source? -Kristian On 10/17/2012 06:50 AM, Steve Barnes wrote: II was told NO!! 27VDC Steve Barnes General Manager PCS-WIN / RC-WiFi http://www.rcwifi.com/ *From:*wireless-boun...@wispa.org [mailto:wireless-boun...@wispa.org] *On Behalf Of *Greg Ihnen *Sent:* Wednesday, October 17, 2012 7:35 AM *To:* WISPA General List *Subject:* Re: [WISPA] Another Ubiquity question Doesn't UBNT gear take up to 30v? Greg On Mon, Oct 15, 2012 at 4:22 PM, Jeromie Reeves jree...@18-30chat.net mailto:jree...@18-30chat.net wrote: Why not run the NSM5 on 24v? Just add a diode or two to the + side, the 1v drop on them will protect the NSM from the charge voltage of the bank. $2 fix On Mon, Oct 15, 2012 at 10:44 AM, Olufemi Adalemo adal...@gmail.com mailto:adal...@gmail.com wrote: It just dawned on me that I may have been barking up the wrong tree I only have the one NSM5 to connect, I could hook this up to the parallel segment of my battery bank and get only 12v while the rest of the installation that's connected in series gets 24v. Do you think this will work? Don't really have to worry about the NSM5 running down the battery cause load is low and the cable run is under 10m so the voltage drop from 12v will be negligible So this is how it would be: 24v solar panel connected to 24v charge controller with 4 x 12v batteries connected in a 2x2 series/parallel array. cable connected to the parallel segment of battery bank (theoretically giving 12v to the NSM5), rest of the load connected to the charge controller at 24v What do you think? - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com mailto:f...@adalemo.com On Fri, Oct 12, 2012 at 8:18 PM, Kristian Hoffmann kh...@fire2wire.com mailto:kh...@fire2wire.com wrote: Ya, it should be +24 on pins 4,5 and -24/comm on 7,8. If it blew up then there was probably a short somewhere. -Kristian On 10/12/2012 11:11 AM, Olufemi Adalemo wrote: Ah ok, it is possible that the guys didn't get the polarity right I will check though they swear that they did - - - Olufemi Adalemo M: +234-803-5610040 tel:%2B234-803-5610040 M: +234-809-8610040 tel:%2B234-809-8610040 f...@adalemo.com mailto:f...@adalemo.com On Fri, Oct 12, 2012 at 7:05 PM, Josh Luthman j...@imaginenetworksllc.com mailto:j...@imaginenetworksllc.com wrote: What voltage were the batteries spitting out? They charge at 27v but without a charger put out much closer to 24v until they begin discharging. If it fried the radio I would first think that it was connected wrong, not that the voltage was too high. Josh Luthman Office: 937-552-2340 tel:937-552-2340 Direct: 937-552-2343 tel:937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 2:02 PM, Olufemi Adalemo adal...@gmail.com mailto:adal...@gmail.com wrote: What's your typical config for the NSM5? Some of my guys just tried to power one off a 24v battery bank (no charger connected just battery) and it fried good - - - Olufemi Adalemo M: +234-803-5610040 tel:%2B234-803-5610040 M: +234-809-8610040 tel:%2B234-809-8610040 f...@adalemo.com mailto:f...@adalemo.com On Fri, Oct 12, 2012 at 6:56 PM, Kristian Hoffmann kh...@fire2wire.com mailto:kh...@fire2wire.com wrote: We have MT and Ubnt equipment of all shapes and sizes running at 27.6V. The only problems we've had are a handful of freak RB411s that won't power on with 27V. Most of the older ones wouldn't kick into overvoltage protection until 28V, but we've come across a few odd balls. -Kristian On 10/12/2012 10:44 AM, Josh Luthman wrote: Charger isn't going to spit out 24v for batteries that need charged, it's usually 27v. I was under the impression they would simply lock up and you could reboot, or maybe I'm just thinking of MT. Josh Luthman Office: 937-552-2340 tel:937-552-2340 Direct: 937-552-2343 tel:937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 10:08 PM, Olufemi Adalemo adal...@gmail.com mailto:adal...@gmail.com wrote: Aha, thanks That explains why I have a dead NSM5 on my desk I guess the charge controller is not very good at giving out 24v regulated power - - - Olufemi Adalemo M: +234-803-5610040 tel:%2B234-803-5610040 M: +234-809-8610040 tel:%2B234-809-8610040 f...@adalemo.com mailto:f...@adalemo.com On Fri, Oct 12, 2012 at 6:17 PM, Josh Luthman j...@imaginenetworksllc.com mailto:j...@imaginenetworksllc.com wrote: Yes you will. The batteries will probably be around 27v which Ubnt won't like. You'll need to clean the ~18-27v from the batteries to 24v. Josh Luthman Office: 937-552
Re: [WISPA] Another Ubiquity question
Many UBNT deployments running at 27volts of clean DC power. Not saying it's ideal but it works. Justin -Original Message- From: Matt Hoppes mhop...@indigowireless.com Reply-To: WISPA General List wireless@wispa.org Date: Wednesday, October 17, 2012 9:25 PM To: WISPA General List wireless@wispa.org Subject: Re: [WISPA] Another Ubiquity question The forums and Matt Hardy I believe will back this up. You'll fry at over 27 volts. Kristian Hoffmann kh...@fire2wire.com wrote: Can you reveal your source? -Kristian On 10/17/2012 06:50 AM, Steve Barnes wrote: II was told NO!! 27VDC Steve Barnes General Manager PCS-WIN / RC-WiFi http://www.rcwifi.com/ *From:*wireless-boun...@wispa.org [mailto:wireless-boun...@wispa.org] *On Behalf Of *Greg Ihnen *Sent:* Wednesday, October 17, 2012 7:35 AM *To:* WISPA General List *Subject:* Re: [WISPA] Another Ubiquity question Doesn't UBNT gear take up to 30v? Greg On Mon, Oct 15, 2012 at 4:22 PM, Jeromie Reeves jree...@18-30chat.net mailto:jree...@18-30chat.net wrote: Why not run the NSM5 on 24v? Just add a diode or two to the + side, the 1v drop on them will protect the NSM from the charge voltage of the bank. $2 fix On Mon, Oct 15, 2012 at 10:44 AM, Olufemi Adalemo adal...@gmail.com mailto:adal...@gmail.com wrote: It just dawned on me that I may have been barking up the wrong tree I only have the one NSM5 to connect, I could hook this up to the parallel segment of my battery bank and get only 12v while the rest of the installation that's connected in series gets 24v. Do you think this will work? Don't really have to worry about the NSM5 running down the battery cause load is low and the cable run is under 10m so the voltage drop from 12v will be negligible So this is how it would be: 24v solar panel connected to 24v charge controller with 4 x 12v batteries connected in a 2x2 series/parallel array. cable connected to the parallel segment of battery bank (theoretically giving 12v to the NSM5), rest of the load connected to the charge controller at 24v What do you think? - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com mailto:f...@adalemo.com On Fri, Oct 12, 2012 at 8:18 PM, Kristian Hoffmann kh...@fire2wire.com mailto:kh...@fire2wire.com wrote: Ya, it should be +24 on pins 4,5 and -24/comm on 7,8. If it blew up then there was probably a short somewhere. -Kristian On 10/12/2012 11:11 AM, Olufemi Adalemo wrote: Ah ok, it is possible that the guys didn't get the polarity right I will check though they swear that they did - - - Olufemi Adalemo M: +234-803-5610040 tel:%2B234-803-5610040 M: +234-809-8610040 tel:%2B234-809-8610040 f...@adalemo.com mailto:f...@adalemo.com On Fri, Oct 12, 2012 at 7:05 PM, Josh Luthman j...@imaginenetworksllc.com mailto:j...@imaginenetworksllc.com wrote: What voltage were the batteries spitting out? They charge at 27v but without a charger put out much closer to 24v until they begin discharging. If it fried the radio I would first think that it was connected wrong, not that the voltage was too high. Josh Luthman Office: 937-552-2340 tel:937-552-2340 Direct: 937-552-2343 tel:937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 2:02 PM, Olufemi Adalemo adal...@gmail.com mailto:adal...@gmail.com wrote: What's your typical config for the NSM5? Some of my guys just tried to power one off a 24v battery bank (no charger connected just battery) and it fried good - - - Olufemi Adalemo M: +234-803-5610040 tel:%2B234-803-5610040 M: +234-809-8610040 tel:%2B234-809-8610040 f...@adalemo.com mailto:f...@adalemo.com On Fri, Oct 12, 2012 at 6:56 PM, Kristian Hoffmann kh...@fire2wire.com mailto:kh...@fire2wire.com wrote: We have MT and Ubnt equipment of all shapes and sizes running at 27.6V. The only problems we've had are a handful of freak RB411s that won't power on with 27V. Most of the older ones wouldn't kick into overvoltage protection until 28V, but we've come across a few odd balls. -Kristian On 10/12/2012 10:44 AM, Josh Luthman wrote: Charger isn't going to spit out 24v for batteries that need charged, it's usually 27v. I was under the impression they would simply lock up and you could reboot, or maybe I'm just thinking of MT. Josh Luthman Office: 937-552-2340 tel:937-552-2340 Direct: 937-552-2343 tel:937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 10:08 PM, Olufemi Adalemo adal...@gmail.com mailto:adal...@gmail.com wrote: Aha, thanks That explains why I have a dead NSM5 on my desk I guess the charge controller is not very good at giving out 24v regulated power - - - Olufemi Adalemo M: +234-803-5610040 tel:%2B234-803-5610040 M: +234-809-8610040 tel:%2B234-809-8610040
Re: [WISPA] Another Ubiquity question
On Wed, Oct 17, 2012 at 10:14:03PM -0400, Justin Wilson wrote: Many UBNT deployments running at 27volts of clean DC power. Not saying it's ideal but it works. 27v at the ethernet port or 27v at the base of the tower? -- Scott LambertKC5MLE Unix SysAdmin lamb...@lambertfam.org ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless
Re: [WISPA] Another Ubiquity question
The problem isn't that you'll completely discharge the part of the bank you're pulling 12v off of, but rather if you discharge the bank unevenly and charge the entire bank in series then you're either overcharging the part you're not pulling 12v off of in order to properly charge the part you are pulling 12v off of -or- you're going to undercharge the part where you are pulling off 12v if you properly charge the part of the bank where you are aren't pulling 12v off. There's just no way around that. Swapping which part of the bank you're using to pull off the 12v will help but you'll want to swap much more frequently thank bi-anullay. You'll want to swap at least once a month. If you only need 8W of power, then if you use a 24v to 12v regulator that's 90% efficient or better the losses will be negligible. Greg On Mon, Oct 15, 2012 at 7:54 PM, Olufemi Adalemo adal...@gmail.com wrote: Thanks Greg, I can see how putting load on just one part of the battery bank could cause issues but this load is quite small compared to the total battery capacity. I will be putting only 8w on two 150Ah 12v batteries (3600Wh total capacity). It would take 400 hours to deplete the battery bank with this load only, do you still think this will be a problem? If this will be a problem I could have the load moved from one bank to the other at a scheduled maintenance visit say twice a year. I really appreciate the advice. Regards, - - - *Olufemi Adalemo* M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Mon, Oct 15, 2012 at 8:19 PM, Greg Ihnen os10ru...@gmail.com wrote: My two cents: If you discharge part of your battery bank unevenly (pull off just half of your 24v bank to get 12v for some loads) you will have trouble with part of the bank getting over charged and part of the bank not getting charged enough. If you were charging the bank with an AC charger that charges each battery individually according to it's needs that wouldn't be a problem. But if you're charging the entire bank with a single device that charges the entire string in series like a 24v solar charger that is not a good way to go. You'd be better off with a 24v to 12v regulator. Greg On Mon, Oct 15, 2012 at 1:44 PM, Olufemi Adalemo adal...@gmail.comwrote: It just dawned on me that I may have been barking up the wrong tree I only have the one NSM5 to connect, I could hook this up to the parallel segment of my battery bank and get only 12v while the rest of the installation that's connected in series gets 24v. Do you think this will work? Don't really have to worry about the NSM5 running down the battery cause load is low and the cable run is under 10m so the voltage drop from 12v will be negligible So this is how it would be: 24v solar panel connected to 24v charge controller with 4 x 12v batteries connected in a 2x2 series/parallel array. cable connected to the parallel segment of battery bank (theoretically giving 12v to the NSM5), rest of the load connected to the charge controller at 24v What do you think? - - - *Olufemi Adalemo* M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless
Re: [WISPA] Another Ubiquity question
It just dawned on me that I may have been barking up the wrong tree I only have the one NSM5 to connect, I could hook this up to the parallel segment of my battery bank and get only 12v while the rest of the installation that's connected in series gets 24v. Do you think this will work? Don't really have to worry about the NSM5 running down the battery cause load is low and the cable run is under 10m so the voltage drop from 12v will be negligible So this is how it would be: 24v solar panel connected to 24v charge controller with 4 x 12v batteries connected in a 2x2 series/parallel array. cable connected to the parallel segment of battery bank (theoretically giving 12v to the NSM5), rest of the load connected to the charge controller at 24v What do you think? - - - *Olufemi Adalemo* M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 8:18 PM, Kristian Hoffmann kh...@fire2wire.comwrote: Ya, it should be +24 on pins 4,5 and -24/comm on 7,8. If it blew up then there was probably a short somewhere. -Kristian On 10/12/2012 11:11 AM, Olufemi Adalemo wrote: Ah ok, it is possible that the guys didn't get the polarity right I will check though they swear that they did - - - *Olufemi Adalemo* M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 7:05 PM, Josh Luthman j...@imaginenetworksllc.com wrote: What voltage were the batteries spitting out? They charge at 27v but without a charger put out much closer to 24v until they begin discharging. If it fried the radio I would first think that it was connected wrong, not that the voltage was too high. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 2:02 PM, Olufemi Adalemo adal...@gmail.comwrote: What's your typical config for the NSM5? Some of my guys just tried to power one off a 24v battery bank (no charger connected just battery) and it fried good - - - *Olufemi Adalemo* M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 6:56 PM, Kristian Hoffmann kh...@fire2wire.com wrote: We have MT and Ubnt equipment of all shapes and sizes running at 27.6V. The only problems we've had are a handful of freak RB411s that won't power on with 27V. Most of the older ones wouldn't kick into overvoltage protection until 28V, but we've come across a few odd balls. -Kristian On 10/12/2012 10:44 AM, Josh Luthman wrote: Charger isn't going to spit out 24v for batteries that need charged, it's usually 27v. I was under the impression they would simply lock up and you could reboot, or maybe I'm just thinking of MT. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 10:08 PM, Olufemi Adalemo adal...@gmail.comwrote: Aha, thanks That explains why I have a dead NSM5 on my desk I guess the charge controller is not very good at giving out 24v regulated power - - - *Olufemi Adalemo* M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 6:17 PM, Josh Luthman j...@imaginenetworksllc.com wrote: Yes you will. The batteries will probably be around 27v which Ubnt won't like. You'll need to clean the ~18-27v from the batteries to 24v. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 1:14 PM, Olufemi Adalemo adal...@gmail.comwrote: Need help, I'm looking to deploy a UBNT NSM5 powered by a 24v solar supply. Does anyone have experience with this? The data sheet shows that it requires a 24v supply however the POE injector supplied is 15v, do I need a DC to DC converter? Best regards, - - - *Olufemi Adalemo* M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing listWireless@wispa.orghttp://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless
Re: [WISPA] Another Ubiquity question
~12v should be OK by specs, but I've never heard of anyone doing such a low voltage to a Ubnt device. Not sure if no ones tried it or it just ended quickly in failure. Just be aware that 24v and 12v batteries have a higher voltage for charging. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Mon, Oct 15, 2012 at 1:44 PM, Olufemi Adalemo adal...@gmail.com wrote: It just dawned on me that I may have been barking up the wrong tree I only have the one NSM5 to connect, I could hook this up to the parallel segment of my battery bank and get only 12v while the rest of the installation that's connected in series gets 24v. Do you think this will work? Don't really have to worry about the NSM5 running down the battery cause load is low and the cable run is under 10m so the voltage drop from 12v will be negligible So this is how it would be: 24v solar panel connected to 24v charge controller with 4 x 12v batteries connected in a 2x2 series/parallel array. cable connected to the parallel segment of battery bank (theoretically giving 12v to the NSM5), rest of the load connected to the charge controller at 24v What do you think? - - - *Olufemi Adalemo* M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 8:18 PM, Kristian Hoffmann kh...@fire2wire.comwrote: Ya, it should be +24 on pins 4,5 and -24/comm on 7,8. If it blew up then there was probably a short somewhere. -Kristian On 10/12/2012 11:11 AM, Olufemi Adalemo wrote: Ah ok, it is possible that the guys didn't get the polarity right I will check though they swear that they did - - - *Olufemi Adalemo* M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 7:05 PM, Josh Luthman j...@imaginenetworksllc.com wrote: What voltage were the batteries spitting out? They charge at 27v but without a charger put out much closer to 24v until they begin discharging. If it fried the radio I would first think that it was connected wrong, not that the voltage was too high. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 2:02 PM, Olufemi Adalemo adal...@gmail.comwrote: What's your typical config for the NSM5? Some of my guys just tried to power one off a 24v battery bank (no charger connected just battery) and it fried good - - - *Olufemi Adalemo* M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 6:56 PM, Kristian Hoffmann kh...@fire2wire.com wrote: We have MT and Ubnt equipment of all shapes and sizes running at 27.6V. The only problems we've had are a handful of freak RB411s that won't power on with 27V. Most of the older ones wouldn't kick into overvoltage protection until 28V, but we've come across a few odd balls. -Kristian On 10/12/2012 10:44 AM, Josh Luthman wrote: Charger isn't going to spit out 24v for batteries that need charged, it's usually 27v. I was under the impression they would simply lock up and you could reboot, or maybe I'm just thinking of MT. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 10:08 PM, Olufemi Adalemo adal...@gmail.comwrote: Aha, thanks That explains why I have a dead NSM5 on my desk I guess the charge controller is not very good at giving out 24v regulated power - - - *Olufemi Adalemo* M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 6:17 PM, Josh Luthman j...@imaginenetworksllc.com wrote: Yes you will. The batteries will probably be around 27v which Ubnt won't like. You'll need to clean the ~18-27v from the batteries to 24v. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 1:14 PM, Olufemi Adalemo adal...@gmail.com wrote: Need help, I'm looking to deploy a UBNT NSM5 powered by a 24v solar supply. Does anyone have experience with this? The data sheet shows that it requires a 24v supply however the POE injector supplied is 15v, do I need a DC to DC converter? Best regards, - - - *Olufemi Adalemo* M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing listWireless@wispa.orghttp://lists.wispa.org/mailman/listinfo/wireless ___ Wireless
Re: [WISPA] Another Ubiquity question
I've had installations like this. Its best to move the radio periodically if you are draining the batteries. Akinlolu C. Ajayi-Obe +234(0)8023258027 -Original Message- From: Olufemi Adalemo adal...@gmail.com Sender: wireless-boun...@wispa.org Date: Mon, 15 Oct 2012 18:44:26 To: WISPA General Listwireless@wispa.org Reply-To: WISPA General List wireless@wispa.org Subject: Re: [WISPA] Another Ubiquity question ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless
Re: [WISPA] Another Ubiquity question
I have done this at home with a Pico M2HP. My setup has two 60w 12v solar panels connected to a charge controller with 2 12v 55AH AGM batteries in parallel. The Pico is connected to the load output of the charge controller with a DC input POE injector that I bought from Amazon for about $10. The setup works pretty good and I've had my first true test of the battery bank this past month. Its rained here every day for the last three weeks. --Eric Roth Network Engineer Webjogger Internet Services (845) 757-4000 www.webjogger.net From: wireless-boun...@wispa.org [mailto:wireless-boun...@wispa.org] On Behalf Of Josh Luthman Sent: Monday, October 15, 2012 1:51 PM To: WISPA General List Subject: Re: [WISPA] Another Ubiquity question ~12v should be OK by specs, but I've never heard of anyone doing such a low voltage to a Ubnt device. Not sure if no ones tried it or it just ended quickly in failure. Just be aware that 24v and 12v batteries have a higher voltage for charging. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Mon, Oct 15, 2012 at 1:44 PM, Olufemi Adalemo adal...@gmail.com wrote: It just dawned on me that I may have been barking up the wrong tree I only have the one NSM5 to connect, I could hook this up to the parallel segment of my battery bank and get only 12v while the rest of the installation that's connected in series gets 24v. Do you think this will work? Don't really have to worry about the NSM5 running down the battery cause load is low and the cable run is under 10m so the voltage drop from 12v will be negligible So this is how it would be: 24v solar panel connected to 24v charge controller with 4 x 12v batteries connected in a 2x2 series/parallel array. cable connected to the parallel segment of battery bank (theoretically giving 12v to the NSM5), rest of the load connected to the charge controller at 24v What do you think? - - - Olufemi Adalemo M: +234-803-5610040 tel:%2B234-803-5610040 M: +234-809-8610040 tel:%2B234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 8:18 PM, Kristian Hoffmann kh...@fire2wire.com wrote: Ya, it should be +24 on pins 4,5 and -24/comm on 7,8. If it blew up then there was probably a short somewhere. -Kristian On 10/12/2012 11:11 AM, Olufemi Adalemo wrote: Ah ok, it is possible that the guys didn't get the polarity right I will check though they swear that they did - - - Olufemi Adalemo M: +234-803-5610040 tel:%2B234-803-5610040 M: +234-809-8610040 tel:%2B234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 7:05 PM, Josh Luthman j...@imaginenetworksllc.com wrote: What voltage were the batteries spitting out? They charge at 27v but without a charger put out much closer to 24v until they begin discharging. If it fried the radio I would first think that it was connected wrong, not that the voltage was too high. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 2:02 PM, Olufemi Adalemo adal...@gmail.com wrote: What's your typical config for the NSM5? Some of my guys just tried to power one off a 24v battery bank (no charger connected just battery) and it fried good - - - Olufemi Adalemo M: +234-803-5610040 tel:%2B234-803-5610040 M: +234-809-8610040 tel:%2B234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 6:56 PM, Kristian Hoffmann kh...@fire2wire.com wrote: We have MT and Ubnt equipment of all shapes and sizes running at 27.6V. The only problems we've had are a handful of freak RB411s that won't power on with 27V. Most of the older ones wouldn't kick into overvoltage protection until 28V, but we've come across a few odd balls. -Kristian On 10/12/2012 10:44 AM, Josh Luthman wrote: Charger isn't going to spit out 24v for batteries that need charged, it's usually 27v. I was under the impression they would simply lock up and you could reboot, or maybe I'm just thinking of MT. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 10:08 PM, Olufemi Adalemo adal...@gmail.com wrote: Aha, thanks That explains why I have a dead NSM5 on my desk I guess the charge controller is not very good at giving out 24v regulated power - - - Olufemi Adalemo M: +234-803-5610040 tel:%2B234-803-5610040 M: +234-809-8610040 tel:%2B234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 6:17 PM, Josh Luthman j...@imaginenetworksllc.com wrote: Yes you will. The batteries will probably be around 27v which Ubnt won't like. You'll need to clean the ~18-27v from the batteries to 24v. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 1:14 PM, Olufemi Adalemo adal...@gmail.com wrote: Need help, I'm looking to deploy a UBNT NSM5 powered by a 24v solar supply. Does
Re: [WISPA] Another Ubiquity question
My two cents: If you discharge part of your battery bank unevenly (pull off just half of your 24v bank to get 12v for some loads) you will have trouble with part of the bank getting over charged and part of the bank not getting charged enough. If you were charging the bank with an AC charger that charges each battery individually according to it's needs that wouldn't be a problem. But if you're charging the entire bank with a single device that charges the entire string in series like a 24v solar charger that is not a good way to go. You'd be better off with a 24v to 12v regulator. Greg On Mon, Oct 15, 2012 at 1:44 PM, Olufemi Adalemo adal...@gmail.com wrote: It just dawned on me that I may have been barking up the wrong tree I only have the one NSM5 to connect, I could hook this up to the parallel segment of my battery bank and get only 12v while the rest of the installation that's connected in series gets 24v. Do you think this will work? Don't really have to worry about the NSM5 running down the battery cause load is low and the cable run is under 10m so the voltage drop from 12v will be negligible So this is how it would be: 24v solar panel connected to 24v charge controller with 4 x 12v batteries connected in a 2x2 series/parallel array. cable connected to the parallel segment of battery bank (theoretically giving 12v to the NSM5), rest of the load connected to the charge controller at 24v What do you think? - - - *Olufemi Adalemo* M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 8:18 PM, Kristian Hoffmann kh...@fire2wire.comwrote: Ya, it should be +24 on pins 4,5 and -24/comm on 7,8. If it blew up then there was probably a short somewhere. -Kristian On 10/12/2012 11:11 AM, Olufemi Adalemo wrote: Ah ok, it is possible that the guys didn't get the polarity right I will check though they swear that they did - - - *Olufemi Adalemo* M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 7:05 PM, Josh Luthman j...@imaginenetworksllc.com wrote: What voltage were the batteries spitting out? They charge at 27v but without a charger put out much closer to 24v until they begin discharging. If it fried the radio I would first think that it was connected wrong, not that the voltage was too high. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 2:02 PM, Olufemi Adalemo adal...@gmail.comwrote: What's your typical config for the NSM5? Some of my guys just tried to power one off a 24v battery bank (no charger connected just battery) and it fried good - - - *Olufemi Adalemo* M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 6:56 PM, Kristian Hoffmann kh...@fire2wire.com wrote: We have MT and Ubnt equipment of all shapes and sizes running at 27.6V. The only problems we've had are a handful of freak RB411s that won't power on with 27V. Most of the older ones wouldn't kick into overvoltage protection until 28V, but we've come across a few odd balls. -Kristian On 10/12/2012 10:44 AM, Josh Luthman wrote: Charger isn't going to spit out 24v for batteries that need charged, it's usually 27v. I was under the impression they would simply lock up and you could reboot, or maybe I'm just thinking of MT. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 10:08 PM, Olufemi Adalemo adal...@gmail.comwrote: Aha, thanks That explains why I have a dead NSM5 on my desk I guess the charge controller is not very good at giving out 24v regulated power - - - *Olufemi Adalemo* M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 6:17 PM, Josh Luthman j...@imaginenetworksllc.com wrote: Yes you will. The batteries will probably be around 27v which Ubnt won't like. You'll need to clean the ~18-27v from the batteries to 24v. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 1:14 PM, Olufemi Adalemo adal...@gmail.com wrote: Need help, I'm looking to deploy a UBNT NSM5 powered by a 24v solar supply. Does anyone have experience with this? The data sheet shows that it requires a 24v supply however the POE injector supplied is 15v, do I need a DC to DC converter? Best regards, - - - *Olufemi Adalemo* M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org
Re: [WISPA] Another Ubiquity question
I have a PS2 wired to the 12 starting battery of a generator which starts and stops a few times a day with no issues. The PS2 doesn't even reset when the gen starts and the battery pulls down to around 8~9 volts while the starter is cranking. When the gen runs the batt voltage goes to ~14.6. Greg On Mon, Oct 15, 2012 at 1:50 PM, Josh Luthman j...@imaginenetworksllc.comwrote: ~12v should be OK by specs, but I've never heard of anyone doing such a low voltage to a Ubnt device. Not sure if no ones tried it or it just ended quickly in failure. Just be aware that 24v and 12v batteries have a higher voltage for charging. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Mon, Oct 15, 2012 at 1:44 PM, Olufemi Adalemo adal...@gmail.comwrote: It just dawned on me that I may have been barking up the wrong tree I only have the one NSM5 to connect, I could hook this up to the parallel segment of my battery bank and get only 12v while the rest of the installation that's connected in series gets 24v. Do you think this will work? Don't really have to worry about the NSM5 running down the battery cause load is low and the cable run is under 10m so the voltage drop from 12v will be negligible So this is how it would be: 24v solar panel connected to 24v charge controller with 4 x 12v batteries connected in a 2x2 series/parallel array. cable connected to the parallel segment of battery bank (theoretically giving 12v to the NSM5), rest of the load connected to the charge controller at 24v What do you think? - - - *Olufemi Adalemo* M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 8:18 PM, Kristian Hoffmann kh...@fire2wire.comwrote: Ya, it should be +24 on pins 4,5 and -24/comm on 7,8. If it blew up then there was probably a short somewhere. -Kristian On 10/12/2012 11:11 AM, Olufemi Adalemo wrote: Ah ok, it is possible that the guys didn't get the polarity right I will check though they swear that they did - - - *Olufemi Adalemo* M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 7:05 PM, Josh Luthman j...@imaginenetworksllc.com wrote: What voltage were the batteries spitting out? They charge at 27v but without a charger put out much closer to 24v until they begin discharging. If it fried the radio I would first think that it was connected wrong, not that the voltage was too high. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 2:02 PM, Olufemi Adalemo adal...@gmail.comwrote: What's your typical config for the NSM5? Some of my guys just tried to power one off a 24v battery bank (no charger connected just battery) and it fried good - - - *Olufemi Adalemo* M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 6:56 PM, Kristian Hoffmann kh...@fire2wire.com wrote: We have MT and Ubnt equipment of all shapes and sizes running at 27.6V. The only problems we've had are a handful of freak RB411s that won't power on with 27V. Most of the older ones wouldn't kick into overvoltage protection until 28V, but we've come across a few odd balls. -Kristian On 10/12/2012 10:44 AM, Josh Luthman wrote: Charger isn't going to spit out 24v for batteries that need charged, it's usually 27v. I was under the impression they would simply lock up and you could reboot, or maybe I'm just thinking of MT. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 10:08 PM, Olufemi Adalemo adal...@gmail.comwrote: Aha, thanks That explains why I have a dead NSM5 on my desk I guess the charge controller is not very good at giving out 24v regulated power - - - *Olufemi Adalemo* M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 6:17 PM, Josh Luthman j...@imaginenetworksllc.com wrote: Yes you will. The batteries will probably be around 27v which Ubnt won't like. You'll need to clean the ~18-27v from the batteries to 24v. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 1:14 PM, Olufemi Adalemo adal...@gmail.com wrote: Need help, I'm looking to deploy a UBNT NSM5 powered by a 24v solar supply. Does anyone have experience with this? The data sheet shows that it requires a 24v supply however the POE injector supplied is 15v, do I need a DC to DC converter? Best regards, - - - *Olufemi Adalemo* M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org
Re: [WISPA] Another Ubiquity question
Why not run the NSM5 on 24v? Just add a diode or two to the + side, the 1v drop on them will protect the NSM from the charge voltage of the bank. $2 fix On Mon, Oct 15, 2012 at 10:44 AM, Olufemi Adalemo adal...@gmail.com wrote: It just dawned on me that I may have been barking up the wrong tree I only have the one NSM5 to connect, I could hook this up to the parallel segment of my battery bank and get only 12v while the rest of the installation that's connected in series gets 24v. Do you think this will work? Don't really have to worry about the NSM5 running down the battery cause load is low and the cable run is under 10m so the voltage drop from 12v will be negligible So this is how it would be: 24v solar panel connected to 24v charge controller with 4 x 12v batteries connected in a 2x2 series/parallel array. cable connected to the parallel segment of battery bank (theoretically giving 12v to the NSM5), rest of the load connected to the charge controller at 24v What do you think? - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 8:18 PM, Kristian Hoffmann kh...@fire2wire.com wrote: Ya, it should be +24 on pins 4,5 and -24/comm on 7,8. If it blew up then there was probably a short somewhere. -Kristian On 10/12/2012 11:11 AM, Olufemi Adalemo wrote: Ah ok, it is possible that the guys didn't get the polarity right I will check though they swear that they did - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 7:05 PM, Josh Luthman j...@imaginenetworksllc.com wrote: What voltage were the batteries spitting out? They charge at 27v but without a charger put out much closer to 24v until they begin discharging. If it fried the radio I would first think that it was connected wrong, not that the voltage was too high. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 2:02 PM, Olufemi Adalemo adal...@gmail.com wrote: What's your typical config for the NSM5? Some of my guys just tried to power one off a 24v battery bank (no charger connected just battery) and it fried good - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 6:56 PM, Kristian Hoffmann kh...@fire2wire.com wrote: We have MT and Ubnt equipment of all shapes and sizes running at 27.6V. The only problems we've had are a handful of freak RB411s that won't power on with 27V. Most of the older ones wouldn't kick into overvoltage protection until 28V, but we've come across a few odd balls. -Kristian On 10/12/2012 10:44 AM, Josh Luthman wrote: Charger isn't going to spit out 24v for batteries that need charged, it's usually 27v. I was under the impression they would simply lock up and you could reboot, or maybe I'm just thinking of MT. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 10:08 PM, Olufemi Adalemo adal...@gmail.com wrote: Aha, thanks That explains why I have a dead NSM5 on my desk I guess the charge controller is not very good at giving out 24v regulated power - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 6:17 PM, Josh Luthman j...@imaginenetworksllc.com wrote: Yes you will. The batteries will probably be around 27v which Ubnt won't like. You'll need to clean the ~18-27v from the batteries to 24v. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 1:14 PM, Olufemi Adalemo adal...@gmail.com wrote: Need help, I'm looking to deploy a UBNT NSM5 powered by a 24v solar supply. Does anyone have experience with this? The data sheet shows that it requires a 24v supply however the POE injector supplied is 15v, do I need a DC to DC converter? Best regards, - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless
Re: [WISPA] Another Ubiquity question
I tried that method. Diode got hotter than hell. Burnt right through the insulation I covered it with (and since it was bent the jacket came right off). Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Mon, Oct 15, 2012 at 4:22 PM, Jeromie Reeves jree...@18-30chat.netwrote: Why not run the NSM5 on 24v? Just add a diode or two to the + side, the 1v drop on them will protect the NSM from the charge voltage of the bank. $2 fix On Mon, Oct 15, 2012 at 10:44 AM, Olufemi Adalemo adal...@gmail.com wrote: It just dawned on me that I may have been barking up the wrong tree I only have the one NSM5 to connect, I could hook this up to the parallel segment of my battery bank and get only 12v while the rest of the installation that's connected in series gets 24v. Do you think this will work? Don't really have to worry about the NSM5 running down the battery cause load is low and the cable run is under 10m so the voltage drop from 12v will be negligible So this is how it would be: 24v solar panel connected to 24v charge controller with 4 x 12v batteries connected in a 2x2 series/parallel array. cable connected to the parallel segment of battery bank (theoretically giving 12v to the NSM5), rest of the load connected to the charge controller at 24v What do you think? - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 8:18 PM, Kristian Hoffmann kh...@fire2wire.com wrote: Ya, it should be +24 on pins 4,5 and -24/comm on 7,8. If it blew up then there was probably a short somewhere. -Kristian On 10/12/2012 11:11 AM, Olufemi Adalemo wrote: Ah ok, it is possible that the guys didn't get the polarity right I will check though they swear that they did - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 7:05 PM, Josh Luthman j...@imaginenetworksllc.com wrote: What voltage were the batteries spitting out? They charge at 27v but without a charger put out much closer to 24v until they begin discharging. If it fried the radio I would first think that it was connected wrong, not that the voltage was too high. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 2:02 PM, Olufemi Adalemo adal...@gmail.com wrote: What's your typical config for the NSM5? Some of my guys just tried to power one off a 24v battery bank (no charger connected just battery) and it fried good - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 6:56 PM, Kristian Hoffmann kh...@fire2wire.com wrote: We have MT and Ubnt equipment of all shapes and sizes running at 27.6V. The only problems we've had are a handful of freak RB411s that won't power on with 27V. Most of the older ones wouldn't kick into overvoltage protection until 28V, but we've come across a few odd balls. -Kristian On 10/12/2012 10:44 AM, Josh Luthman wrote: Charger isn't going to spit out 24v for batteries that need charged, it's usually 27v. I was under the impression they would simply lock up and you could reboot, or maybe I'm just thinking of MT. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 10:08 PM, Olufemi Adalemo adal...@gmail.com wrote: Aha, thanks That explains why I have a dead NSM5 on my desk I guess the charge controller is not very good at giving out 24v regulated power - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 6:17 PM, Josh Luthman j...@imaginenetworksllc.com wrote: Yes you will. The batteries will probably be around 27v which Ubnt won't like. You'll need to clean the ~18-27v from the batteries to 24v. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 1:14 PM, Olufemi Adalemo adal...@gmail.com wrote: Need help, I'm looking to deploy a UBNT NSM5 powered by a 24v solar supply. Does anyone have experience with this? The data sheet shows that it requires a 24v supply however the POE injector supplied is 15v, do I need a DC to DC converter? Best regards, - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless
Re: [WISPA] Another Ubiquity question
hehe. well now you know why Rectifiers.. (large diodes) have heatsinks on them :) Faisal Imtiaz Snappy Internet Telecom 7266 SW 48 Street Miami, Fl 33155 Tel: 305 663 5518 x 232 Helpdesk: 305 663 5518 option 2 Email: supp...@snappydsl.net On 10/15/2012 4:38 PM, Josh Luthman wrote: I tried that method. Diode got hotter than hell. Burnt right through the insulation I covered it with (and since it was bent the jacket came right off). Josh Luthman Office: 937-552-2340 tel:937-552-2340 Direct: 937-552-2343 tel:937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Mon, Oct 15, 2012 at 4:22 PM, Jeromie Reeves jree...@18-30chat.net mailto:jree...@18-30chat.net wrote: Why not run the NSM5 on 24v? Just add a diode or two to the + side, the 1v drop on them will protect the NSM from the charge voltage of the bank. $2 fix On Mon, Oct 15, 2012 at 10:44 AM, Olufemi Adalemo adal...@gmail.com mailto:adal...@gmail.com wrote: It just dawned on me that I may have been barking up the wrong tree I only have the one NSM5 to connect, I could hook this up to the parallel segment of my battery bank and get only 12v while the rest of the installation that's connected in series gets 24v. Do you think this will work? Don't really have to worry about the NSM5 running down the battery cause load is low and the cable run is under 10m so the voltage drop from 12v will be negligible So this is how it would be: 24v solar panel connected to 24v charge controller with 4 x 12v batteries connected in a 2x2 series/parallel array. cable connected to the parallel segment of battery bank (theoretically giving 12v to the NSM5), rest of the load connected to the charge controller at 24v What do you think? - - - Olufemi Adalemo M: +234-803-5610040 tel:%2B234-803-5610040 M: +234-809-8610040 tel:%2B234-809-8610040 f...@adalemo.com mailto:f...@adalemo.com On Fri, Oct 12, 2012 at 8:18 PM, Kristian Hoffmann kh...@fire2wire.com mailto:kh...@fire2wire.com wrote: Ya, it should be +24 on pins 4,5 and -24/comm on 7,8. If it blew up then there was probably a short somewhere. -Kristian On 10/12/2012 11:11 AM, Olufemi Adalemo wrote: Ah ok, it is possible that the guys didn't get the polarity right I will check though they swear that they did - - - Olufemi Adalemo M: +234-803-5610040 tel:%2B234-803-5610040 M: +234-809-8610040 tel:%2B234-809-8610040 f...@adalemo.com mailto:f...@adalemo.com On Fri, Oct 12, 2012 at 7:05 PM, Josh Luthman j...@imaginenetworksllc.com mailto:j...@imaginenetworksllc.com wrote: What voltage were the batteries spitting out? They charge at 27v but without a charger put out much closer to 24v until they begin discharging. If it fried the radio I would first think that it was connected wrong, not that the voltage was too high. Josh Luthman Office: 937-552-2340 tel:937-552-2340 Direct: 937-552-2343 tel:937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 2:02 PM, Olufemi Adalemo adal...@gmail.com mailto:adal...@gmail.com wrote: What's your typical config for the NSM5? Some of my guys just tried to power one off a 24v battery bank (no charger connected just battery) and it fried good - - - Olufemi Adalemo M: +234-803-5610040 tel:%2B234-803-5610040 M: +234-809-8610040 tel:%2B234-809-8610040 f...@adalemo.com mailto:f...@adalemo.com On Fri, Oct 12, 2012 at 6:56 PM, Kristian Hoffmann kh...@fire2wire.com mailto:kh...@fire2wire.com wrote: We have MT and Ubnt equipment of all shapes and sizes running at 27.6V. The only problems we've had are a handful of freak RB411s that won't power on with 27V. Most of the older ones wouldn't kick into overvoltage protection until 28V, but we've come across a few odd balls. -Kristian On 10/12/2012 10:44 AM, Josh Luthman wrote: Charger isn't going to spit out 24v for batteries that need charged, it's usually 27v. I was under the impression they would simply lock up and you could reboot, or maybe I'm just thinking of MT. Josh Luthman Office: 937-552-2340 tel:937-552-2340 Direct: 937-552-2343 tel:937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 10:08 PM, Olufemi Adalemo adal...@gmail.com mailto:adal...@gmail.com wrote: Aha, thanks That explains why I have a dead NSM5 on my desk I guess the charge controller is not very good at giving out 24v regulated power
Re: [WISPA] Another Ubiquity question
Mine doesn't. Only doing about 25 watts though. On Oct 15, 2012 4:54 PM, Faisal Imtiaz fai...@snappydsl.net wrote: hehe. well now you know why Rectifiers.. (large diodes) have heatsinks on them :) Faisal Imtiaz Snappy Internet Telecom 7266 SW 48 Street Miami, Fl 33155 Tel: 305 663 5518 x 232 Helpdesk: 305 663 5518 option 2 Email: supp...@snappydsl.net On 10/15/2012 4:38 PM, Josh Luthman wrote: I tried that method. Diode got hotter than hell. Burnt right through the insulation I covered it with (and since it was bent the jacket came right off). Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Mon, Oct 15, 2012 at 4:22 PM, Jeromie Reeves jree...@18-30chat.netwrote: Why not run the NSM5 on 24v? Just add a diode or two to the + side, the 1v drop on them will protect the NSM from the charge voltage of the bank. $2 fix On Mon, Oct 15, 2012 at 10:44 AM, Olufemi Adalemo adal...@gmail.com wrote: It just dawned on me that I may have been barking up the wrong tree I only have the one NSM5 to connect, I could hook this up to the parallel segment of my battery bank and get only 12v while the rest of the installation that's connected in series gets 24v. Do you think this will work? Don't really have to worry about the NSM5 running down the battery cause load is low and the cable run is under 10m so the voltage drop from 12v will be negligible So this is how it would be: 24v solar panel connected to 24v charge controller with 4 x 12v batteries connected in a 2x2 series/parallel array. cable connected to the parallel segment of battery bank (theoretically giving 12v to the NSM5), rest of the load connected to the charge controller at 24v What do you think? - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 8:18 PM, Kristian Hoffmann kh...@fire2wire.com wrote: Ya, it should be +24 on pins 4,5 and -24/comm on 7,8. If it blew up then there was probably a short somewhere. -Kristian On 10/12/2012 11:11 AM, Olufemi Adalemo wrote: Ah ok, it is possible that the guys didn't get the polarity right I will check though they swear that they did - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 7:05 PM, Josh Luthman j...@imaginenetworksllc.com wrote: What voltage were the batteries spitting out? They charge at 27v but without a charger put out much closer to 24v until they begin discharging. If it fried the radio I would first think that it was connected wrong, not that the voltage was too high. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 2:02 PM, Olufemi Adalemo adal...@gmail.com wrote: What's your typical config for the NSM5? Some of my guys just tried to power one off a 24v battery bank (no charger connected just battery) and it fried good - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 6:56 PM, Kristian Hoffmann kh...@fire2wire.com wrote: We have MT and Ubnt equipment of all shapes and sizes running at 27.6V. The only problems we've had are a handful of freak RB411s that won't power on with 27V. Most of the older ones wouldn't kick into overvoltage protection until 28V, but we've come across a few odd balls. -Kristian On 10/12/2012 10:44 AM, Josh Luthman wrote: Charger isn't going to spit out 24v for batteries that need charged, it's usually 27v. I was under the impression they would simply lock up and you could reboot, or maybe I'm just thinking of MT. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 10:08 PM, Olufemi Adalemo adal...@gmail.com wrote: Aha, thanks That explains why I have a dead NSM5 on my desk I guess the charge controller is not very good at giving out 24v regulated power - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 6:17 PM, Josh Luthman j...@imaginenetworksllc.com wrote: Yes you will. The batteries will probably be around 27v which Ubnt won't like. You'll need to clean the ~18-27v from the batteries to 24v. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 1:14 PM, Olufemi Adalemo adal...@gmail.com wrote: Need help, I'm looking to deploy a UBNT NSM5 powered by a 24v solar supply. Does anyone have experience with this? The data sheet shows that it requires a 24v supply however the POE injector supplied is 15v, do I need a DC to DC converter? Best regards, - - - Olufemi
Re: [WISPA] Another Ubiquity question
Where did you put that diode? I have done this and at the low power that is needed they do not get noticeably warm at all. On Mon, Oct 15, 2012 at 1:38 PM, Josh Luthman j...@imaginenetworksllc.com wrote: I tried that method. Diode got hotter than hell. Burnt right through the insulation I covered it with (and since it was bent the jacket came right off). Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Mon, Oct 15, 2012 at 4:22 PM, Jeromie Reeves jree...@18-30chat.net wrote: Why not run the NSM5 on 24v? Just add a diode or two to the + side, the 1v drop on them will protect the NSM from the charge voltage of the bank. $2 fix On Mon, Oct 15, 2012 at 10:44 AM, Olufemi Adalemo adal...@gmail.com wrote: It just dawned on me that I may have been barking up the wrong tree I only have the one NSM5 to connect, I could hook this up to the parallel segment of my battery bank and get only 12v while the rest of the installation that's connected in series gets 24v. Do you think this will work? Don't really have to worry about the NSM5 running down the battery cause load is low and the cable run is under 10m so the voltage drop from 12v will be negligible So this is how it would be: 24v solar panel connected to 24v charge controller with 4 x 12v batteries connected in a 2x2 series/parallel array. cable connected to the parallel segment of battery bank (theoretically giving 12v to the NSM5), rest of the load connected to the charge controller at 24v What do you think? - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 8:18 PM, Kristian Hoffmann kh...@fire2wire.com wrote: Ya, it should be +24 on pins 4,5 and -24/comm on 7,8. If it blew up then there was probably a short somewhere. -Kristian On 10/12/2012 11:11 AM, Olufemi Adalemo wrote: Ah ok, it is possible that the guys didn't get the polarity right I will check though they swear that they did - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 7:05 PM, Josh Luthman j...@imaginenetworksllc.com wrote: What voltage were the batteries spitting out? They charge at 27v but without a charger put out much closer to 24v until they begin discharging. If it fried the radio I would first think that it was connected wrong, not that the voltage was too high. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 2:02 PM, Olufemi Adalemo adal...@gmail.com wrote: What's your typical config for the NSM5? Some of my guys just tried to power one off a 24v battery bank (no charger connected just battery) and it fried good - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 6:56 PM, Kristian Hoffmann kh...@fire2wire.com wrote: We have MT and Ubnt equipment of all shapes and sizes running at 27.6V. The only problems we've had are a handful of freak RB411s that won't power on with 27V. Most of the older ones wouldn't kick into overvoltage protection until 28V, but we've come across a few odd balls. -Kristian On 10/12/2012 10:44 AM, Josh Luthman wrote: Charger isn't going to spit out 24v for batteries that need charged, it's usually 27v. I was under the impression they would simply lock up and you could reboot, or maybe I'm just thinking of MT. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 10:08 PM, Olufemi Adalemo adal...@gmail.com wrote: Aha, thanks That explains why I have a dead NSM5 on my desk I guess the charge controller is not very good at giving out 24v regulated power - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 6:17 PM, Josh Luthman j...@imaginenetworksllc.com wrote: Yes you will. The batteries will probably be around 27v which Ubnt won't like. You'll need to clean the ~18-27v from the batteries to 24v. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 1:14 PM, Olufemi Adalemo adal...@gmail.com wrote: Need help, I'm looking to deploy a UBNT NSM5 powered by a 24v solar supply. Does anyone have experience with this? The data sheet shows that it requires a 24v supply however the POE injector supplied is 15v, do I need a DC to DC converter? Best regards, - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com ___ Wireless mailing list Wireless@wispa.org
Re: [WISPA] Another Ubiquity question
Between the regulator and load. On Oct 15, 2012 5:01 PM, Jeromie Reeves jree...@18-30chat.net wrote: Where did you put that diode? I have done this and at the low power that is needed they do not get noticeably warm at all. On Mon, Oct 15, 2012 at 1:38 PM, Josh Luthman j...@imaginenetworksllc.com wrote: I tried that method. Diode got hotter than hell. Burnt right through the insulation I covered it with (and since it was bent the jacket came right off). Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Mon, Oct 15, 2012 at 4:22 PM, Jeromie Reeves jree...@18-30chat.net wrote: Why not run the NSM5 on 24v? Just add a diode or two to the + side, the 1v drop on them will protect the NSM from the charge voltage of the bank. $2 fix On Mon, Oct 15, 2012 at 10:44 AM, Olufemi Adalemo adal...@gmail.com wrote: It just dawned on me that I may have been barking up the wrong tree I only have the one NSM5 to connect, I could hook this up to the parallel segment of my battery bank and get only 12v while the rest of the installation that's connected in series gets 24v. Do you think this will work? Don't really have to worry about the NSM5 running down the battery cause load is low and the cable run is under 10m so the voltage drop from 12v will be negligible So this is how it would be: 24v solar panel connected to 24v charge controller with 4 x 12v batteries connected in a 2x2 series/parallel array. cable connected to the parallel segment of battery bank (theoretically giving 12v to the NSM5), rest of the load connected to the charge controller at 24v What do you think? - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 8:18 PM, Kristian Hoffmann kh...@fire2wire.com wrote: Ya, it should be +24 on pins 4,5 and -24/comm on 7,8. If it blew up then there was probably a short somewhere. -Kristian On 10/12/2012 11:11 AM, Olufemi Adalemo wrote: Ah ok, it is possible that the guys didn't get the polarity right I will check though they swear that they did - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 7:05 PM, Josh Luthman j...@imaginenetworksllc.com wrote: What voltage were the batteries spitting out? They charge at 27v but without a charger put out much closer to 24v until they begin discharging. If it fried the radio I would first think that it was connected wrong, not that the voltage was too high. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 2:02 PM, Olufemi Adalemo adal...@gmail.com wrote: What's your typical config for the NSM5? Some of my guys just tried to power one off a 24v battery bank (no charger connected just battery) and it fried good - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 6:56 PM, Kristian Hoffmann kh...@fire2wire.com wrote: We have MT and Ubnt equipment of all shapes and sizes running at 27.6V. The only problems we've had are a handful of freak RB411s that won't power on with 27V. Most of the older ones wouldn't kick into overvoltage protection until 28V, but we've come across a few odd balls. -Kristian On 10/12/2012 10:44 AM, Josh Luthman wrote: Charger isn't going to spit out 24v for batteries that need charged, it's usually 27v. I was under the impression they would simply lock up and you could reboot, or maybe I'm just thinking of MT. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 10:08 PM, Olufemi Adalemo adal...@gmail.com wrote: Aha, thanks That explains why I have a dead NSM5 on my desk I guess the charge controller is not very good at giving out 24v regulated power - - - Olufemi Adalemo M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 6:17 PM, Josh Luthman j...@imaginenetworksllc.com wrote: Yes you will. The batteries will probably be around 27v which Ubnt won't like. You'll need to clean the ~18-27v from the batteries to 24v. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 1:14 PM, Olufemi Adalemo adal...@gmail.com wrote: Need help, I'm looking to deploy a UBNT NSM5 powered by a 24v solar supply. Does anyone have experience with this? The data sheet shows that it requires a 24v supply however the POE
Re: [WISPA] Another Ubiquity question
Thanks Greg, I can see how putting load on just one part of the battery bank could cause issues but this load is quite small compared to the total battery capacity. I will be putting only 8w on two 150Ah 12v batteries (3600Wh total capacity). It would take 400 hours to deplete the battery bank with this load only, do you still think this will be a problem? If this will be a problem I could have the load moved from one bank to the other at a scheduled maintenance visit say twice a year. I really appreciate the advice. Regards, - - - *Olufemi Adalemo* M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Mon, Oct 15, 2012 at 8:19 PM, Greg Ihnen os10ru...@gmail.com wrote: My two cents: If you discharge part of your battery bank unevenly (pull off just half of your 24v bank to get 12v for some loads) you will have trouble with part of the bank getting over charged and part of the bank not getting charged enough. If you were charging the bank with an AC charger that charges each battery individually according to it's needs that wouldn't be a problem. But if you're charging the entire bank with a single device that charges the entire string in series like a 24v solar charger that is not a good way to go. You'd be better off with a 24v to 12v regulator. Greg On Mon, Oct 15, 2012 at 1:44 PM, Olufemi Adalemo adal...@gmail.comwrote: It just dawned on me that I may have been barking up the wrong tree I only have the one NSM5 to connect, I could hook this up to the parallel segment of my battery bank and get only 12v while the rest of the installation that's connected in series gets 24v. Do you think this will work? Don't really have to worry about the NSM5 running down the battery cause load is low and the cable run is under 10m so the voltage drop from 12v will be negligible So this is how it would be: 24v solar panel connected to 24v charge controller with 4 x 12v batteries connected in a 2x2 series/parallel array. cable connected to the parallel segment of battery bank (theoretically giving 12v to the NSM5), rest of the load connected to the charge controller at 24v What do you think? - - - *Olufemi Adalemo* M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless
Re: [WISPA] Another Ubiquity question
Yes you will. The batteries will probably be around 27v which Ubnt won't like. You'll need to clean the ~18-27v from the batteries to 24v. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 1:14 PM, Olufemi Adalemo adal...@gmail.com wrote: Need help, I'm looking to deploy a UBNT NSM5 powered by a 24v solar supply. Does anyone have experience with this? The data sheet shows that it requires a 24v supply however the POE injector supplied is 15v, do I need a DC to DC converter? Best regards, - - - *Olufemi Adalemo* M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless
Re: [WISPA] Another Ubiquity question
Aha, thanks That explains why I have a dead NSM5 on my desk I guess the charge controller is not very good at giving out 24v regulated power - - - *Olufemi Adalemo* M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 6:17 PM, Josh Luthman j...@imaginenetworksllc.comwrote: Yes you will. The batteries will probably be around 27v which Ubnt won't like. You'll need to clean the ~18-27v from the batteries to 24v. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 1:14 PM, Olufemi Adalemo adal...@gmail.comwrote: Need help, I'm looking to deploy a UBNT NSM5 powered by a 24v solar supply. Does anyone have experience with this? The data sheet shows that it requires a 24v supply however the POE injector supplied is 15v, do I need a DC to DC converter? Best regards, - - - *Olufemi Adalemo* M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless
Re: [WISPA] Another Ubiquity question
Charger isn't going to spit out 24v for batteries that need charged, it's usually 27v. I was under the impression they would simply lock up and you could reboot, or maybe I'm just thinking of MT. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 10:08 PM, Olufemi Adalemo adal...@gmail.com wrote: Aha, thanks That explains why I have a dead NSM5 on my desk I guess the charge controller is not very good at giving out 24v regulated power - - - *Olufemi Adalemo* M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 6:17 PM, Josh Luthman j...@imaginenetworksllc.com wrote: Yes you will. The batteries will probably be around 27v which Ubnt won't like. You'll need to clean the ~18-27v from the batteries to 24v. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 1:14 PM, Olufemi Adalemo adal...@gmail.comwrote: Need help, I'm looking to deploy a UBNT NSM5 powered by a 24v solar supply. Does anyone have experience with this? The data sheet shows that it requires a 24v supply however the POE injector supplied is 15v, do I need a DC to DC converter? Best regards, - - - *Olufemi Adalemo* M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless
Re: [WISPA] Another Ubiquity question
We have MT and Ubnt equipment of all shapes and sizes running at 27.6V. The only problems we've had are a handful of freak RB411s that won't power on with 27V. Most of the older ones wouldn't kick into overvoltage protection until 28V, but we've come across a few odd balls. -Kristian On 10/12/2012 10:44 AM, Josh Luthman wrote: Charger isn't going to spit out 24v for batteries that need charged, it's usually 27v. I was under the impression they would simply lock up and you could reboot, or maybe I'm just thinking of MT. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 10:08 PM, Olufemi Adalemo adal...@gmail.com mailto:adal...@gmail.com wrote: Aha, thanks That explains why I have a dead NSM5 on my desk I guess the charge controller is not very good at giving out 24v regulated power - - - *Olufemi Adalemo* M: +234-803-5610040 tel:%2B234-803-5610040 M: +234-809-8610040 tel:%2B234-809-8610040 f...@adalemo.com mailto:f...@adalemo.com On Fri, Oct 12, 2012 at 6:17 PM, Josh Luthman j...@imaginenetworksllc.com mailto:j...@imaginenetworksllc.com wrote: Yes you will. The batteries will probably be around 27v which Ubnt won't like. You'll need to clean the ~18-27v from the batteries to 24v. Josh Luthman Office: 937-552-2340 tel:937-552-2340 Direct: 937-552-2343 tel:937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 1:14 PM, Olufemi Adalemo adal...@gmail.com mailto:adal...@gmail.com wrote: Need help, I'm looking to deploy a UBNT NSM5 powered by a 24v solar supply. Does anyone have experience with this? The data sheet shows that it requires a 24v supply however the POE injector supplied is 15v, do I need a DC to DC converter? Best regards, - - - *Olufemi Adalemo* M: +234-803-5610040 tel:%2B234-803-5610040 M: +234-809-8610040 tel:%2B234-809-8610040 f...@adalemo.com mailto:f...@adalemo.com ___ Wireless mailing list Wireless@wispa.org mailto:Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org mailto:Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org mailto:Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless
Re: [WISPA] Another Ubiquity question
What's your typical config for the NSM5? Some of my guys just tried to power one off a 24v battery bank (no charger connected just battery) and it fried good - - - *Olufemi Adalemo* M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 6:56 PM, Kristian Hoffmann kh...@fire2wire.comwrote: We have MT and Ubnt equipment of all shapes and sizes running at 27.6V. The only problems we've had are a handful of freak RB411s that won't power on with 27V. Most of the older ones wouldn't kick into overvoltage protection until 28V, but we've come across a few odd balls. -Kristian On 10/12/2012 10:44 AM, Josh Luthman wrote: Charger isn't going to spit out 24v for batteries that need charged, it's usually 27v. I was under the impression they would simply lock up and you could reboot, or maybe I'm just thinking of MT. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 10:08 PM, Olufemi Adalemo adal...@gmail.comwrote: Aha, thanks That explains why I have a dead NSM5 on my desk I guess the charge controller is not very good at giving out 24v regulated power - - - *Olufemi Adalemo* M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 6:17 PM, Josh Luthman j...@imaginenetworksllc.com wrote: Yes you will. The batteries will probably be around 27v which Ubnt won't like. You'll need to clean the ~18-27v from the batteries to 24v. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 1:14 PM, Olufemi Adalemo adal...@gmail.comwrote: Need help, I'm looking to deploy a UBNT NSM5 powered by a 24v solar supply. Does anyone have experience with this? The data sheet shows that it requires a 24v supply however the POE injector supplied is 15v, do I need a DC to DC converter? Best regards, - - - *Olufemi Adalemo* M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing listWireless@wispa.orghttp://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless
Re: [WISPA] Another Ubiquity question
What voltage were the batteries spitting out? They charge at 27v but without a charger put out much closer to 24v until they begin discharging. If it fried the radio I would first think that it was connected wrong, not that the voltage was too high. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 2:02 PM, Olufemi Adalemo adal...@gmail.com wrote: What's your typical config for the NSM5? Some of my guys just tried to power one off a 24v battery bank (no charger connected just battery) and it fried good - - - *Olufemi Adalemo* M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 6:56 PM, Kristian Hoffmann kh...@fire2wire.comwrote: We have MT and Ubnt equipment of all shapes and sizes running at 27.6V. The only problems we've had are a handful of freak RB411s that won't power on with 27V. Most of the older ones wouldn't kick into overvoltage protection until 28V, but we've come across a few odd balls. -Kristian On 10/12/2012 10:44 AM, Josh Luthman wrote: Charger isn't going to spit out 24v for batteries that need charged, it's usually 27v. I was under the impression they would simply lock up and you could reboot, or maybe I'm just thinking of MT. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 10:08 PM, Olufemi Adalemo adal...@gmail.comwrote: Aha, thanks That explains why I have a dead NSM5 on my desk I guess the charge controller is not very good at giving out 24v regulated power - - - *Olufemi Adalemo* M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 6:17 PM, Josh Luthman j...@imaginenetworksllc.com wrote: Yes you will. The batteries will probably be around 27v which Ubnt won't like. You'll need to clean the ~18-27v from the batteries to 24v. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 1:14 PM, Olufemi Adalemo adal...@gmail.comwrote: Need help, I'm looking to deploy a UBNT NSM5 powered by a 24v solar supply. Does anyone have experience with this? The data sheet shows that it requires a 24v supply however the POE injector supplied is 15v, do I need a DC to DC converter? Best regards, - - - *Olufemi Adalemo* M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing listWireless@wispa.orghttp://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless
Re: [WISPA] Another Ubiquity question
Ah ok, it is possible that the guys didn't get the polarity right I will check though they swear that they did - - - *Olufemi Adalemo* M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 7:05 PM, Josh Luthman j...@imaginenetworksllc.comwrote: What voltage were the batteries spitting out? They charge at 27v but without a charger put out much closer to 24v until they begin discharging. If it fried the radio I would first think that it was connected wrong, not that the voltage was too high. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 2:02 PM, Olufemi Adalemo adal...@gmail.comwrote: What's your typical config for the NSM5? Some of my guys just tried to power one off a 24v battery bank (no charger connected just battery) and it fried good - - - *Olufemi Adalemo* M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 6:56 PM, Kristian Hoffmann kh...@fire2wire.comwrote: We have MT and Ubnt equipment of all shapes and sizes running at 27.6V. The only problems we've had are a handful of freak RB411s that won't power on with 27V. Most of the older ones wouldn't kick into overvoltage protection until 28V, but we've come across a few odd balls. -Kristian On 10/12/2012 10:44 AM, Josh Luthman wrote: Charger isn't going to spit out 24v for batteries that need charged, it's usually 27v. I was under the impression they would simply lock up and you could reboot, or maybe I'm just thinking of MT. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 10:08 PM, Olufemi Adalemo adal...@gmail.comwrote: Aha, thanks That explains why I have a dead NSM5 on my desk I guess the charge controller is not very good at giving out 24v regulated power - - - *Olufemi Adalemo* M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com On Fri, Oct 12, 2012 at 6:17 PM, Josh Luthman j...@imaginenetworksllc.com wrote: Yes you will. The batteries will probably be around 27v which Ubnt won't like. You'll need to clean the ~18-27v from the batteries to 24v. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 1:14 PM, Olufemi Adalemo adal...@gmail.comwrote: Need help, I'm looking to deploy a UBNT NSM5 powered by a 24v solar supply. Does anyone have experience with this? The data sheet shows that it requires a 24v supply however the POE injector supplied is 15v, do I need a DC to DC converter? Best regards, - - - *Olufemi Adalemo* M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing listWireless@wispa.orghttp://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless
Re: [WISPA] Another Ubiquity question
I've used a 24v AC-DC power supply with cable length 80M. Been up 6months. Akinlolu C. Ajayi-Obe +234(0)8023258027 -Original Message- From: Olufemi Adalemo adal...@gmail.com Sender: wireless-boun...@wispa.org Date: Fri, 12 Oct 2012 18:14:58 To: WISPA Listwireless@wispa.org Reply-To: WISPA General List wireless@wispa.org Subject: [WISPA] Another Ubiquity question ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless
Re: [WISPA] Another Ubiquity question
Ya, it should be +24 on pins 4,5 and -24/comm on 7,8. If it blew up then there was probably a short somewhere. -Kristian On 10/12/2012 11:11 AM, Olufemi Adalemo wrote: Ah ok, it is possible that the guys didn't get the polarity right I will check though they swear that they did - - - *Olufemi Adalemo* M: +234-803-5610040 M: +234-809-8610040 f...@adalemo.com mailto:f...@adalemo.com On Fri, Oct 12, 2012 at 7:05 PM, Josh Luthman j...@imaginenetworksllc.com mailto:j...@imaginenetworksllc.com wrote: What voltage were the batteries spitting out? They charge at 27v but without a charger put out much closer to 24v until they begin discharging. If it fried the radio I would first think that it was connected wrong, not that the voltage was too high. Josh Luthman Office: 937-552-2340 tel:937-552-2340 Direct: 937-552-2343 tel:937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 2:02 PM, Olufemi Adalemo adal...@gmail.com mailto:adal...@gmail.com wrote: What's your typical config for the NSM5? Some of my guys just tried to power one off a 24v battery bank (no charger connected just battery) and it fried good - - - *Olufemi Adalemo* M: +234-803-5610040 tel:%2B234-803-5610040 M: +234-809-8610040 tel:%2B234-809-8610040 f...@adalemo.com mailto:f...@adalemo.com On Fri, Oct 12, 2012 at 6:56 PM, Kristian Hoffmann kh...@fire2wire.com mailto:kh...@fire2wire.com wrote: We have MT and Ubnt equipment of all shapes and sizes running at 27.6V. The only problems we've had are a handful of freak RB411s that won't power on with 27V. Most of the older ones wouldn't kick into overvoltage protection until 28V, but we've come across a few odd balls. -Kristian On 10/12/2012 10:44 AM, Josh Luthman wrote: Charger isn't going to spit out 24v for batteries that need charged, it's usually 27v. I was under the impression they would simply lock up and you could reboot, or maybe I'm just thinking of MT. Josh Luthman Office: 937-552-2340 tel:937-552-2340 Direct: 937-552-2343 tel:937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 10:08 PM, Olufemi Adalemo adal...@gmail.com mailto:adal...@gmail.com wrote: Aha, thanks That explains why I have a dead NSM5 on my desk I guess the charge controller is not very good at giving out 24v regulated power - - - *Olufemi Adalemo* M: +234-803-5610040 tel:%2B234-803-5610040 M: +234-809-8610040 tel:%2B234-809-8610040 f...@adalemo.com mailto:f...@adalemo.com On Fri, Oct 12, 2012 at 6:17 PM, Josh Luthman j...@imaginenetworksllc.com mailto:j...@imaginenetworksllc.com wrote: Yes you will. The batteries will probably be around 27v which Ubnt won't like. You'll need to clean the ~18-27v from the batteries to 24v. Josh Luthman Office: 937-552-2340 tel:937-552-2340 Direct: 937-552-2343 tel:937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Oct 12, 2012 at 1:14 PM, Olufemi Adalemo adal...@gmail.com mailto:adal...@gmail.com wrote: Need help, I'm looking to deploy a UBNT NSM5 powered by a 24v solar supply. Does anyone have experience with this? The data sheet shows that it requires a 24v supply however the POE injector supplied is 15v, do I need a DC to DC converter? Best regards, - - - *Olufemi Adalemo* M: +234-803-5610040 tel:%2B234-803-5610040 M: +234-809-8610040 tel:%2B234-809-8610040 f...@adalemo.com mailto:f...@adalemo.com ___ Wireless mailing list Wireless@wispa.org mailto:Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org mailto:Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless
Re: [WISPA] Another Ubiquity question
I have several radios working off solar for years. Good charge controller and batteries works perfect! tony Olufemi Adalemo Friday, October 12, 2012 11:14 AM Need help,I'm looking to deploy a UBNT NSM5 powered by a 24v solar supply.Does anyone have experience with this? The data sheet shows that it requires a 24v supply however the POE injector supplied is 15v, do I need a DC to DC converter? Best regards,- - -Olufemi Adalemo M: +234-803-5610040M: +234-809-8610040 f...@adalemo.com ___Wireless mailing listWireless@wispa.orghttp://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless