Jim,
If you want to fire up ur rig and call CQ on 7160 when there is a qso
on 7161, 7158 or 7162 be my guest, it is your station not mine, but
where I come from, we call people who do that lids.
73
Rob K5UJ
On Sun, Sep 20, 2009 at 6:38 PM, Jim Wilhite w...@brightok.net wrote:
There are people
Rob, I don't think that is what Jim is suggesting at all. Rather, he is
likely referring to the 'dead air' groups who leave a radio running to
listen for their buddies, but aren't in QSO. You can listen to the frequency
for long periods with no activity. But call CQ or ask if the frequency is in
You are correct Todd, that is precisely what I meant. There are several
groups like this scattered around mostly in the lower part of the phone
segment. I have had run ins with them not only on AM but SSB. Rod,
amateur radio is not an intercom now does anyone own a frequency as Todd
says.
Just as a side note - a tip of the hat to the oft-time phenomenal
band conditions that can exist on 40m in the DAYTIME hours
for a good AM contact
I have known 40m to produce some great S9+2-dB signals from
simple 30-40 watt AM transmitters over rather short distances - say
out to around
You're right - and for heavens' sakes if you say Is this frequency in use?
They will come backl and say yes, and start talking with each other for
a few minutes then back to their standby mode.
In traffic terms these are called road hogs - the guy who drives at
20 mph under the speed limit in
To a certain extent, the same thing has happened on 40m since (most of) the
BC stations went away, as happened on 75 when the band was expanded down to
3600. Back in the spring, there was a lot of activity on 7160 at first,
until the novelty wore off, and gradually the activity has dwindled.
Hi Jerry... I have 2 heil PR-40 mics that I use on
Am... These have tremendous low end. I have a
GATES BC1G Broadcast xmtr that off course can take
the low end... I use a Radio Design labs mixer
with their parametric EQ and a URIE Limiter.
Everyone one says it sounds as good as some of the
best AM
How about against the RE27, your opinion?
Philip LaMarche
LaMarche Enterprises, Inc.
www.instantgourmetspices.com
www.w9dvm.com
800-395-7795 pin 02
727-944-3226
FAX 727-937-8834
NASFT 30210
K3 #1605
CCA 98 00827
CRA 1701
W9DVM
-Original Message-
From:
Amateurs operating in IARU Region 1 can't operate above 3.8 MHz and
amateurs in IARU Region 3 can't operate above 3.9 Mhz. So, to be more
consistant with the rest of the world, if you 're going to petition the
FCC for more U. S. phone space on 40 meters to be more consistant with
the rest of the
I would say better then the RE27 PhilMore and
More BC stations are buying Heil over EV... Steve
W5SAW that you see on the list here is a Broadcast
engineer and now recommends Heil over EV all the
time... He likes the PR-30 a lot and recommends
it... Off course the price I gave was minus shock
Heil's PR-781 works great on AM and full body SSB.
Pete, wa2cwa
-Original Message-
From: amradio-boun...@mailman.qth.net
[mailto:amradio-boun...@mailman.qth.net] On Behalf
Of Gerald Stockinger
Sent: Monday, September 21, 2009 10:10 AM
To: AM Radio
Subject: [AMRadio] Microphone
I use a K3 on SSB and a 32V-3 on AM. What recommendation for the Collins.
Get rave reviews with a D-104 every time I get on.
Phil
Philip LaMarche
LaMarche Enterprises, Inc.
www.instantgourmetspices.com
www.w9dvm.com
800-395-7795 pin 02
727-944-3226
FAX 727-937-8834
NASFT 30210
K3
I see I was consistant; should be consistent.
Pete, wa2cwa
On Mon, 21 Sep 2009 12:21:49 -0400 manualman manual...@juno.com writes:
Amateurs operating in IARU Region 1 can't operate above 3.8 MHz and
amateurs in IARU Region 3 can't operate above 3.9 Mhz. So, to be
more
consistant with the
In all likelihood this is probably a rehash of the Ford-Chevy-Dodge
discussion; but, I do prefer the Heil PR-30/40 over the Electro-Voice
RE-20/27. (Apologies to the Sennheiser and Audio-Technica devotees, I
don't want to leave you out.) While the EV mics are quite good they
have a few bumps
Funny, as I was typing my other mic comments I was thinking that a good
condition, properly adjust D-104 would be the first thing I'd try on
just about any hi-Z input BA rig, especially a Collins.
73 de W5SAW, Steve White
Phil LaMarche wrote:
I use a K3 on SSB and a 32V-3 on AM. What
A 32V series transmitter has very restricted
audio... For those and I always will recommend a
D-104 or a Shure 55
Or 10DA Astatic No low end no high end pretty
well a mid range xmtr
Bob W1PE
-Original Message-
From: amradio-boun...@mailman.qth.net
I agree with that... But not the low end of the 30
and 40...
Bob
-Original Message-
From: amradio-boun...@mailman.qth.net
[mailto:amradio-boun...@mailman.qth.net] On Behalf
Of manualman
Sent: Monday, September 21, 2009 11:24 AM
To: amradio@mailman.qth.net
Subject: Re: [AMRadio]
I use a Heil GM-4 hand mike on am and ssb. I also have a deep voice
and used to be in radio broadcasting. The Heil wide element has a
freq response of 60-16k with a bump at 2k to improve intelligence
while still having a good low end. The mike also has the Heil high
freq element with a
Looking for an interstage audio transformer. PP plates to PPgrids with a 5 to
1 ratio min. A thordarson 20D79 would be ideal.
Please reply off list.
Thanks for looking.
73
K6KWQ Dick
Amps by MORE POWER
__
Our Main Website:
Hi Todd,
Well I certainly apologize to Jim for the misunderstanding, and I did
forget about these dead air groups. This reminds me of once, years
ago, when I asked if the frequency was in use somewhere on 75 meters
and an unidentified voice said, frequency's in use. qso going on
right now. I
Firstly, that's one hell of a first rig for AM! Congratulations. To
me, the mic to use depends on what's been done to the KW1. Is it
stock? A later KW1? It seems to me that then you would want a Hi Z
communications mic. Besides what has been mentioned, there is the
Shure 444 and 520. The
My D-104 seems to work just fine on my unmodified Valiant I and Ranger
I. What microphones have you guys used with those rigs?
Carl Yaffey K8NU
Banjo, guitar, bass, mandolin, dobro lessons.
Pro Tools recording studio.
cyaffeyno_s...@gmail.com
614 268 6353, Columbus OH
I've always had two theories as to why stations continue to purchase
RE27s, one is that if you are already using 5 or 10 of them and all
your processing is set up for the re27, you will be loath to throw
another mic into the mix and have to accommodate it; the other is a
notion true or false, that
Jerry,
There are two good Hi-Z mics that come to mind. Both are, (were), mfg
by Shure. The 55S and the 737A.
Both have a response from about 100cps to 10Kc.
I know that most folks seem to no longer consider them, BUT, Mike M.,
W3NB has won the Heavy Metal Rally several times with his Gates
I can answer that question...Any mic that will
stand up to a Rock band like the EAGLES and being
on the road tour like the Eagles do and many other
groups like Frampton then it will stand up to a Jr
DJ... The PR40 is used on drums all the time and
in the film industry...John BXO mentioned the
Also the EV-664 is a great HI Z mic
Bob W1PE
-Original Message-
From: amradio-boun...@mailman.qth.net
[mailto:amradio-boun...@mailman.qth.net] On Behalf
Of rbethman
Sent: Monday, September 21, 2009 1:44 PM
To: Discussion of AM Radio in the Amateur Service
Subject: Re: [AMRadio]
Jerry,
There are two good Hi-Z mics that come to mind. Both are, (were), mfg
by Shure. The 55S and the 737A.
Both have a response from about 100cps to 10Kc.
I know that most folks seem to no longer consider them, BUT, Mike M.,
*WN3B* (not W3NB), has won the Heavy Metal Rally several times
Bob, As you have pointed out about other microphones, the Shure 55
Series has a VERY long and distinguished history of use under all
conditions on stage.
They get waved around, swung and banged on. They still keep ticking!
Best with 5Meg ohm input, but will also do well as low as 1 Meg Ohm.
I own several Shure 55S and E-V 664 and have used both quite successfully
(in Hi-Z) on my BA transmitters: Apache, DX-100, and the Ranger.
You have to modify the mic input circuits by raising the grid-leak
resistor to at least 5 megohms or more, and change out the coupling caps.
Doing
On Mon, Sep 21, 2009 at 11:09 AM, Gerald Stockinger
cliogunsm...@centurytel.net wrote:
Good morning to all. Since I will soon be new to AM having been on SSB
since 1957 I need the benefit of others experience. Last week a good
amount of time was spent on audio quality so I thought I would
Earlier, in my enthusiasm for Heil mics I failed to mention (except at
the end of my post) that I like and still use Shure mics. The 55S and
737A are good hi-Z mics as are the Shure 585SD, 565SD, and 545SD (all
dual-Z) and the E-V 664 which was a very popular podium mic in the 60s
and 70s. I
Bob Peters wrote:
Also the EV-664 is a great HI Z mic
And, in a pinch, it makes a pretty decent hammer!
73, Bob W9RAN
__
Our Main Website: http://www.amfone.net
AMRadio mailing list
Searchable Archives:
Todd, KA1KAQ wrote:
[lots of snips]
I've always used a crystal D-104 with excellent results, ... but if you do
the simple mods to the audio
of your transmitter and plug in a decent D-104 (make sure the element is in
good shape with a scope), you'll be very pleased.
An excellent place
Greetings!
I recently acquired a beautiful RME 4350 (not A). It looks fantastic,
but it's kind of deaf. It looks like it has been electrically restored
but the previous owner sez he knows nothing (I believe him too). The
sensitivity seems adequate on 160 and then goes down from there with
10
Hi Jerry, I'm looking forward to hearing you on your KW-1.
A couple of questions and some advice regarding mic selection --
1. Is the speech amp modified or stock? If it's stock, take the time to
explore how to by-pass the speech clippers as a first order of business. They
add a tremendous
Todd, KA1KAQ wrote:
You can probably make a soup can sound decent with enough processing,
These fellers sounded pretty good (and got paid ten dollars) for singing
into a can ;-)
http://www.youtube.com/watch?v=krwywj_gIjk
73, Bob W9RAN
Good Afternoon and thanks to all that replied and there were many. When
the name Shure 55 came up I went and looked and sure enough I had one
upstairs in the closet. Bob W0YVA uses one and he runs it into the phone
patch jack which is 600 ohms. So that is a place to start. Many
suggested the
On Mon, Sep 21, 2009 at 4:08 PM, Gerald Stockinger
cliogunsm...@centurytel.net wrote:
So one time out for the audio deck has to
get everything.
That's smart thinking, Jerry. I've had mine out a number of times doing
different stages of work which could have been accomplished in one sitting
Jerry,
On the back of the 55S should be a switch to set for L, M, or H
for impedance.
There are a couple of pages for it on BAMA. Otherwise I can send them
direct by E-MAIL.
These settings provide for a wide range of matching possibilities.
Todd and others can and I'm sure will provide the
Jerry,
You are one hernia ahead of me hi hi; I also have to be careful
lugging heavy iron, rigs etc. around. It sounds like you have a good
plan and are on track. I don't think anyone here has given you bum
advice but with AM and audio there is a lot of it. Todd and Paul VJB
are dead on but I
Amateurs operating in IARU Region 1 can't operate above 3.8 MHz and
amateurs in IARU Region 3 can't operate above 3.9 Mhz. So, to be more
consistant with the rest of the world, if you 're going to petition the
FCC for more U. S. phone space on 40 meters to be more consistant with
the rest
The most important single accessory item to have in your AM shack is a
way to monitor modulation - a cheap o'scope is a good choice. Keep an
eye on it to ensure you have reasonably strong average modulation
levels, and negative peaks that don't go all the way to 100% and pinch
off the carrier.
I see that the Heil Classic 1930s microphone (looks like an RCA 74)
with a high-fidelity dynamic element plus a second element either HC-4
(SSB DX quality) or HC-5 (SSB QSO quality), plus the desk stand, is on
closeout as a package for $99 at Amateur Electronic Supply. There are
pros and cons
I acquired this microphone at its discount price. They have been
discontinued.
It is well worth $99.00
David Knepper, W3ST-W3CRA
Publisher of the Collins Journal and
Secretary to the
Collins Radio Association
www.collinsra.com
---Original Message---
From: sbjohns...@aol.com
Audio Technica was briefly mentioned in the discussion of recommended
microphones.
Has anyone here, especially those who primarily run rice boxes, used the
Audio Technica ATR30?
The EHam reviews are quite positive in its favor, many acclaiming it to be
equal to the Heil mics that have been
That is a GREAT DEAL on that mic...They sound
fantastic on the air...i know a number of guys
that have them//
Bob W1PE
-Original Message-
From: amradio-boun...@mailman.qth.net
[mailto:amradio-boun...@mailman.qth.net] On Behalf
Of sbjohns...@aol.com
Sent: Monday, September 21, 2009 7:17
Steve I use a UREI BL-40 Modulimiter...and it has
A symmetric as well I have a CBS Labs
Limiter...and getting the CBS labs AGC as well as
a pair...
Bob W1PE
-Original Message-
From: amradio-boun...@mailman.qth.net
[mailto:amradio-boun...@mailman.qth.net] On Behalf
Of sbjohns...@aol.com
The D-104 or any other crystal mic needs to work into PLENTY of megohms of
load resistance. Astatic recommends 5 megohms, but I run mine at 10 megs -
probably about as high a grid leak resistance that you can use in a tube
type preamp and maintain stable operation. I have plans in the works
pair of high-mu triodes in a push-pull mic preamp. That way, each tube
can
have its own 10 meg grid leak to allow for a 20 megohm load on the xtal.
It's possible to duplicate a similar circuit using an FET differential
amplifier with dual FETs in a single package (e.g., 2SJ109), or a
OK, Bob - I see you're a nut like me -grin- so I should describe my
current set up for 160m AM.
Right now my Gates BC1T has a Sennheiser 421 dynamic cardioid mic (set
one click off M), feeding a Berhinger VX200 mic processor. Then it
goes thru a fairly noisy Logitek rack mixer to an equalizer
If any of you guy want it I have a schematic for a Mic Pre using a SSM 2019 Mic
Preamp chip. It has a NE5523 line driver output and requires a 15 V. bipolar
supply. It's real straight forward, very quiet, and you can get all the parts
from Mouser or Digikey.
Bill AD5OL
51 matches
Mail list logo