Hi
I have the following problem with my 3640 (16 MB flash and 128 MB RAM). I
have tried several IOS's and also different IOS's from a flash card located
in slot0 - same result.
program load complete, entry point: 0x80008000, size: 0x38f410
Self decompressing the image :
Hi all,
I am implementing Network management System such as
Whatsup Gols. I have also implementated syslog
server.I am planning to implement SNMP server which
will collect all traps . Is there any utility on net
whcih I can use ? Any help will be highly appreciated.
Thanks in advance.
regards
___
either switching or remote access unless you have completed those. The
support exam is cumulative and will cover material from each of the other 3.
Charles
-Original Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of
[EMAIL PROTECTED]
Sent: Thursday, September 05, 20
Teltone makes cheap POTS simulators. You might want to check e-bay.
--
thanks,
-Brad Ellis
CCIE#5796 (R&S / Security)
Network Learning Inc
[EMAIL PROTECTED]
www.optsys.net (Cisco hardware)
Voice: 702-968-5100
FAX: 702-968-5104
""Karl Thrasher"" wrote in message
[EMAIL PROTECTED]">news:[EMAIL
Hi
I agree that there are simulations as well. But, in my BSCI there was just 1
(one) simulation, where I had to configure basic routing on 1 (one) router.
If I remember right it was just 1 router command, 2 or 3 network statements,
1 copy run start, finished.
OK, I needed quite a lot of time for
Team,
I'm going to get my Voice Support certification and was wondering what order
I should take the tests (CVOICE, CIPT, or DQoS). Also are the boson exams
good for practice tests?
Travis Bolton
Network Engineer II
CCNP,CCDA
"Try not to become a man of success, but rather try to become a man
You can use Cisco cache engines. These machines have Rules Template option
and you can filter url's by defining patterns.
-Original Message-
From: Rodney Jackson [mailto:[EMAIL PROTECTED]]
Sent: Thursday, September 05, 2002 4:07 AM
To: [EMAIL PROTECTED]
Subject: Internet control [7:52663
Dont forget the NM-1Vs. Here's what I'd do:
2610 64D/16F
2620 64D/16F (so you can do your trunking with this one too with the FE
interface)
2 or 4 WIC-1Ts (db60 serial interfaces)
2x NM-1V
2x VIC-2FXS
That should do the trick for ya.
thanks,
-Brad Ellis
CCIE#5796 (R&S / Security)
Network Learn
Check anthonypanda dot com for the DTE/DCE back-to-back cables.
There are other sources such as ccbootcamp dot com, and kg2 dor com.
And, never forget to check ebay. Just do a search on 'cisco back' and
you'll find a ton of them.
Good Luck!
Message Posted at:
http://www.groupstudy.com/form/r
Well, for the authentication part you can use the aut
proxy feature (both router IOS and PIX) coupled with a
RADIUS/TACACS server. Local user db will work to.
As far as blocking porn, etc there are other products
like WebSense but thats the only one that works with
the PIX at the moment. You cou
9/5/2002 10:30pm Thursday
You caan do that with Nortel router & a special free program called BNFS95
www.nortelnetworks.com/rml
It works great. I have never tryed it with Cisco. Let me know what
happens.
Richard
//
""Mohamed Saro"" wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTE
hi,
i need to know which exam would be more appropreate to appear for after
the routing exam towards the ccnp cert.
thanks,
jaffar
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=52770&t=52770
--
FAQ, list archives, and s
If your machines are logging onto a domain, use "net send". Use "net
help send" for more information.
-Original Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]
Sent: Thursday, September 05, 2002 6:06 PM
To: [EMAIL PROTECTED]
Subject: pc communication problem [7:52763]
Hi f
All,
I live in San Diego and have recently gotten laid off of a startup
company called Wingcast You may have heard of it. Anyways, I was
wondering how the job market is for Network Engineers in your area. I
have a CCNP and the well is dry here. Just curious how the other areas
are.
Much
Hola Ernesto
dime que version tiene en este momento y cual necesita yo te la puedo
ayudar a conseguir
Carlos Rojas_Morales
Ernesto Diaz wrote:
> Is possible to upgrade a 4-MB Catalyst 2900-XL Switch to 8-MB?
>
>
>
> Regards,
>
>
>
> Ernesto J. Diaz L.
Message Posted at:
http://ww
In cat4003,using model 4306 ,can talking with 2950c ??
How can I do ?
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=52766&t=52766
--
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report mis
How many users per IDF?
Jeff
""John Brandis"" wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> Hi All,
>
> Like my previous emails, had a network designed for some 460 ports.
Hoever,
> like yesterday, I have been told now to cater for some 650 ports, and to
> plan for VOIP in a f
Anyone run into this before?
I pulled a couple 4000's (I believe they are 4000-M's, definately not
regular 4000's, and they don't appear to be 4500 or 4700's), out of a
storage closet.
When I boot up the first one I get the following,
System Bootstrap, Version 4.6(1), SOFTWARE
Copyright (c) 198
Hi folks,
I was wondering if you could help me out on a small project I am working
on. I have two PCs with IP addresses connected to an actual campus LAN,
however, only in a lab do I want to have a router with one PC communicate to
another router with the other PC via a serial connection.(want t
Hi All,
Like my previous emails, had a network designed for some 460 ports. Hoever,
like yesterday, I have been told now to cater for some 650 ports, and to
plan for VOIP in a few months time.
My topology looked like
[Core Switch - Cisco Catalyst 4006]
I just passed the new routing exam. 640-603
I had two questions that had to do with IS-IS. I can tell you that they were
not configuration specific. I would recommend just knowing what type of
routing protocol IS-IS is, and what propoerties apply to that type of
routing protocol.
IE - Just know
I would buy both, it helps to have different sources. I have the cisco press
books and the exam cram series of books. I'm taking the test this weekend,
I'll let you know how it goes without breaking the NDA. Good Luck.
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=52760&t=5272
Hi ! All,
Is anyone out there managing Alcatel devices through Ciscoworks 2000 ?
If yes, than how one can do the configuration management?
Your help is appreciated.
Thanks in advance.
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=52759&t=52759
--
Larry Letterman wrote:
> Dont confuse VOIP with AVVID/IP Telephony..
>
> To run IP Telephony over a cat 5K, use a secondary IP
> address on the router interface that routes the vlan for
> the switch in question. You will need a DHCP server that has
> both primary and secondary scopes, and the pr
Ken,
I don't know of a CCO document off hand (other than a PIX manual) but had a
decent conversation with a TAC engineer a few weeks ago about NAT, VPN, PIX,
a 3015 VPN Concentrator and the way the wo devices treat traffic that may
help you some as it did me.
The catalyst for the conversation wa
Whoever just took that Oct. 28th date in SJ, I'll trade you my Nov. 17th
date! You just beat me to it...=) =)
If anyone has a date between 10/28 and 11/3 in SJ, I have a 11/17 date
to trade with you...Please email me directly
Thanks,
Eddie
Message Posted at:
http://www.groupstudy.com/form/
Yeah, of course, but I would like to make a perl script and I don't want to
use Expect due to political reasons, so I can only use snmp.
Thanx anyway...
Luong, David wrote:
>
> you can do a 'show port x/x' on the switch and under that info,
> it will give
> you the ifindex.
>
> -Original Mes
This commands advertises a 0.0.0.0/0 route via OSPF
with the advertising router as the next-hop. The
next-hop would be the IP address of the interface
connecting to adjancent routers part of the OSPF
domain.
--- Gil Shulman wrote:
> Hi all,
>
> I have been wondering whether someone can help me
Oh thx for that great explanation !!!
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=52753&t=52681
--
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violati
yes - i did save the image ... but guess no luck ... same thing ...
after tftpdnld and xmodem.
if you go to the site you will find that the 48Mb version has enhanced
features ... and there is a version which require only 32 Mb.
i even tried to load an older version - same thing.
thx.
Mes
Use a DB-60 to DB-60 crossover cable. You can find these all over the
Internet and are relatively inexpensive. Configure the clock rate on the
serial interface that the DCE side of the cable is connected to. Then, go to
town. --- On Wed 09/04, Koh Jeff < [EMAIL PROTECTED] > wrote:
Changed your e-m
Dont confuse VOIP with AVVID/IP Telephony..
To run IP Telephony over a cat 5K, use a secondary IP
address on the router interface that routes the vlan for
the switch in question. You will need a DHCP server that has
both primary and secondary scopes, and the primary will service
the data devices
Hi All,
Has someone used the "Study Questions 2002 CD-ROM for the Cisco. CCIE
Written Exam" material, from CertificationZone ?
I would be happy with feedback,
Alaerte
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=52748&t=52748
-
I have an AGS+ for sale works good and a couple of old CGS's that I'd rather
give away than throw in the dumpster.
AGS+ 9 Slot router
- csc/4 processor card with 11.0 roms
- environmental card
- 5 serial ports
- 1 ethernet port
- Lots of extras, a few
Can VOIP work with the CAT5505's? I checked my switch and the set port aux
isn't in there.
MG
wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> Cisco Switches have the ability to have 2 vlans on a single port. The set
> port auxiliaryvlan command on CatOs and switchport voice vlan
Unless you go nuts with them you shouldn't notice any differance. If
your bored read thru this:
http://www.cisco.com/warp/public/473/79.html
Dave
"[EMAIL PROTECTED]" wrote:
>
> Hi All,
>
> I am trying to find the relation between implementing VACLs and changes on
> the speed of switching
Hi All,
I am trying to find the relation between implementing VACLs and changes on
the speed of switching on Catalyst 6500.
I would appreciate any help.
Thanks,
Alaerte
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=52743&t=52743
--
I have a cisco1003 isdn router dialing into another router, in an outher
country, and it has worked perfectly, but now my telco switched the voice
and isdn calls from the fiber to a sattalite, and the the router can not
connect, are thare any timeout settings our somthing like that I can change..
Yes. That's about all it can run in the way of RP's
-Original Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]] On Behalf Of
Ivan
Sent: Thursday, September 05, 2002 9:35 AM
To: [EMAIL PROTECTED]
Subject: Rip on Pix [7:52723]
Hi all,
Can the pix firewall running routing proto
There are lots of good examples for many configuration options here:
http://www.cisco.com/warp/public/110/top_issues/pix/pix_index.shtml
Dave
Ken Diliberto wrote:
>
> Does anyone happen to know a good CCO document describing the way the
> VPN option on the PIX integrates with the firewall?
you can do a 'show port x/x' on the switch and under that info, it will give
you the ifindex.
-Original Message-
From: David j [mailto:[EMAIL PROTECTED]]
Sent: Wednesday, September 04, 2002 2:26 PM
To: [EMAIL PROTECTED]
Subject: OT: SNMP [7:52691]
Anybody knows if there is an algorithm
Nigel,
>From what I understand, as far as the faster convergence times of BGP and
other protocols go, this is more like an IOS improvement.
We all know that giving the same number of bgp sessions, the convergence
times from different vendors are not the same, I guess cisco is just making
IOS mo
hi,
yes i have the right memory image - i tried also with the original IOS found
in the box.
i also followed:
- tftpdnld procedure
- xmodem procedure
the router doesn't boot in normal mode.
the only way i can work with it is via rommon.
yes - i did use the boot command - no result - same beh
you can also use a roll over cable to connect 2 routers through the AUX ports.
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=52735&t=52708
--
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Re
Is there anyway to simulate POTS without an Adtran and more specifically on
any Cisco equipment? I have alot of cisco equip available to me, including
various FXS voice modules, and need a work-around,if possible, w/o
purchasing a 550. (FXS will provide a dial tone, won't it?) No only do I
need to
Is possible to upgrade a 4-MB Catalyst 2900-XL Switch to 8-MB?
Regards,
Ernesto J. Diaz L.
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=52733&t=52733
--
FAQ, list archives, and subscription info: http://www.groupstudy
I used two 2500 routers to practice some of the routing protocols for the
test and for the CIT test. The other equipment I was using through
experience at work.
>From: "Larry Letterman"
>Reply-To: "Larry Letterman"
>To: [EMAIL PROTECTED]
>Subject: RE: CCNP Lab [7:52660]
>Date: Wed, 4 Sep 200
While loopbacks are good in a token ring environment, they are not good in
a Ethernet environment, especially if you are attempting DLSW Transparent
Redundancy.
Brett Johnson
-Original Message-
From: Debbie Westall [mailto:[EMAIL PROTECTED]]
Sent: Thursday, September 05, 2002 9:12 AM
To
Shawn,
Good Point. The books that I am using to Study for the CCIE Written are:
Managing Cisco Network Security - cisco Press
Routing TCP/IP Vol 1 and 2 - doyle
Cisco LAN Switching - Clark
Internet Routing Architectures - Halabi
CCIE practical Studies Vol 1 - Solie
Hope this helps.
Michael
>Fr
Does anyone happen to know a good CCO document describing the way the
VPN option on the PIX integrates with the firewall? I'm wondering if
the VPN traffic passes the firewall encrypted or if it is unencrypted
before the firewall.
Now if only the PIX would transparent bridge...
Thanks.
Messa
If you take a quick look in the group archives at www.groupstudy.com you'll
find several months worth of comments about it, but basically they dropped a
few older technologies, added a bunch of new ones, upped the number of
questions, and ratcheted up the level of the questions. It's much harder,
Hello group,
I would like to take the support exam next month. Can you please recommend
me the best book to buy between Cisco Internet Troubleshooting (CiscoPress)
and Troubleshooting Campus Networks by Priscilla Oppenheimer.
Thank you.
Rock BASSOLE
Message Posted at:
http://www.groupstudy
Greetings,
Please help guys,
I am trying to integrate Cisco Secure ACS 2.1 with RSA ACE/Server 5.0. I
have created an external database and ACS went and count the required DLL
on the system [both ACS & ACE are on the same machine, I did not have to
install the ACE agent].
I then created a user
Adam,
I have used DLSW many times to connect SNA/token rings sites together.
It works great.
One piece of advice I can give when setting up the DLSW, use loopbacks to
form the DLSW "tunnel". This is especially useful if you have redundant
paths to the sites. The loopbacks are always up, so if a l
Hi all,
Can the pix firewall running routing protocol such as RIP?
Thanks & regards,
Ivan
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=52723&t=52723
--
FAQ, list archives, and subscription info: http://www.groupstudy.com/lis
Hi all,
I have been wondering whether someone can help me understand, how to control
which default-gateway will the OSPF mechanism will advertise first, in a
scenario which I have four.
Thank you in advance for any help,
Gil
***
Dear all,Does the Cache Engine-570 supports FTP caching ?If so, how
this could be done transparently without asking users to do any
modifications in their browsers ? Best Regards,Yasser
MSN Photos is the easiest way to
Hi all,
I got a doubt on dlsw I could not find much info in CCO too.
How can we prevent the dlsw connection falling back to the primary peer from
the backup peer. The 'linger' option with '0' sec and the 'no linger' option
does not seems to be working out.
Any helpers please...
thanks
Message
Hi all,
I am just testing the theory here to see if this is possible.
I have a remote site with 2x ISDN BRI and a central site with 2x ISDN BRI.
These BRI's are backing up a dedicated 256k point to point link.
I have dialer interfaces created on both sites with the physical BRI's being
members
DLSW+ does establish a TCP connection between 2 routers by using defined
local and remote peers. The following global config commands are used :
dlsw local-peer peer-id 172.25.250.1
dlsw remote-peer 0 tcp 172.25.250.129
You also need to define a bridge group(SNA is not routable) for DLSW. The
fo
Hi,
Does anyone knows how much is new CCIE written different from old one. I saw
that Cisco added some objectives, there is no appletalk, decnet, fddi, Cisco
added some new tehnologies (wirelless, mpls) but how much are really this
topics coverd on the exam.
Robert
Message Posted at:
http://
61 matches
Mail list logo
