I just recently failed the BSCN test and I have a question. How do you find
the CIR of a Pipe that has Ex: 2 64 and 1 128 PVC's? Would it be the least
PVC times the # of PVC's or what would be the answer. Any help would be
apprecited. Thanks.
_
FAQ, list archi
Does anyone have any Exam prep tests that they would like to exchange for?
I would like the BSCN from Beachfront quizzer if possible. I have BSCN and
BCMSN from Mcse2be.com, and would like to exchange with anyone if they have
another exam prep for the BSCN.
_
FAQ
I have 8 cats separated on 2 floors and I want to create some sort of
failover but want to make sure that it will work and will not cause any
problems. The diagram below is my setup and I have 4 cats on fl1 connected
to 4 cats on fl2 via fiber from sw4 to sw5 but I would like to run a piece
of fi
Does anyone know which options you can set in the IOS to provide for
failover to an ISDN line. I have a T-1 setup with Verio and if that line
fails, I would like to go to ISDN for the backup but am unsure how I would
begin to configure this as far as the ISDN commands are concerned. Thanks.
Is there a way that I can cause a BRI interface to activate when the load
drops to 0 on the T-1 and then deactivate when there is activity on the T-1.
I have a point to point from DE to AZ with constant traffic and I have seen
where an interface will not transmit traffic even though it is being
r
I have an issue with 2 csc 2600 rtr's. When the s0/0 goes down and the
backup ISDN kicks in, from within the router I can ping the ISDN int on the
other side but not the local routers ISDN int? I also cannot ping the other
side from the network internally only pingable from the router CLI? Now
I have a ISDN failover connection and whenever the connection kicks in and I
do a "show IP route" I get the following information and it is not correct.
Atlanta RTR(I did "sh ip ro")- C 128.121.22.146/32 BRI0/0 When in
actuality, the BRI int on the other router is 128.121.22.146/28
I disconn
PX-VER-DE-RTR#sh int bri0/0
BRI0/0 is up, line protocol is up (spoofing)
Hardware is PQUICC BRI with U interface
Internet address is 128.121.22.145/30
MTU 1500 bytes, BW 64 Kbit, DLY 2 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation PPP, loopback not set
Last
PX-VER-DE-RTR#sh int bri0/0
BRI0/0 is up, line protocol is up (spoofing)
Hardware is PQUICC BRI with U interface
Internet address is 128.121.22.145/30
MTU 1500 bytes, BW 64 Kbit, DLY 2 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation PPP, loopback not set
Last
Is ther a way that I can stop all eigrp traffic from passing on the ISDN
when it is down and then to pass when the ISDN comes up? I have an access
list that denies eigrp on the BRI and the interface is set as passive in the
eigrp config. But I am having routing problems when I lose my serial lin
Does anyone know if you can use a clear counters command from the CLI on a
Cat 3548XL to clear multiple int's at one shot?
EX: clear counters fa0/1:48 ?? Thanks.
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=28850&t=28850
--
Can I configure multiple ports at a time for speed from the CLI instead of
all 48 individually?
Catalyst 3548
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=23412&t=23412
--
FAQ, list archives, and subscription info: http://www.
Hi,
I have kind of a stupid question but I am trying to set the time on a
catalyst 3548
Ex: clock set hh:mm:ss date month year? When I go to do the time it is ok
and I always get unrecognized command entering the dat. I have tried every
combination and can't get it to work. I did
clock set 10:2
Hi All,
I have a question ansd would like to know if anyone can help. Cisco states
that The error below is nothing to be concerned about and that the system
should recover just fine, but it is beginning to occur more frequently and I
would like to know if there is anything that can be done. The
Can I assign multiple ports to a vlan in one swoop rather than each one
individually?
IOS on a 3548XL
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=61393&t=61393
--
FAQ, list archives, and subscription info: http://www.groupstu
I have a 2620 rtr and would like to debug the traffic of a particular ip but
the only way I know to do it is byu the following:
debug ip packet 101
where 101 is an acl that says ermit ip any any.
Is there a better way to do this so that it only logs that particular ip top
the screen rather than al
I would do a SHOW FRAME RELAY PVC
and see if the pvc is active. Also ensure that the IP's have the same
subnet and configure the LMI type so that it matches on both ends. Possible
even contact you Frame provider to see what type of LMI the switch supports.
""vikramjskeer"" wrote in message
[E
Another one would be Compuwares ecoscope. It is similar to a sniffer but
only captures header information and will allow to to see where all the load
is coming from on your network. $$
-Original Message-
From: Jim Dixon [mailto:[EMAIL PROTECTED]]
Sent: Thursday, June 14, 2001 3:34 P
I read an e-mail yesterday about Boson BCRAN test and someone wanted to know
which ones were good. I only saw one reply referencing test 2 as ok. I am
taking my test next week and would like to purchase one. Any other feedback
on which one out of the three would be the best??
Bob Perez
EPX
BCSN35
BCMSN 6
- BCRAN ?
- CIT 4
-Original Message-
From: hal9001 [mailto:[EMAIL PROTECTED]]
Sent: Thursday, June 21, 2001 3:48 PM
To: [EMAIL PROTECTED]
Subject: How Hard is Hard - Cisco Exams [7:9410]
Can I please canvass some opin
Don't forget the 1600 series. They also have WIC cards
-Original Message-
From: Circusnuts [mailto:[EMAIL PROTECTED]]
Sent: Monday, June 25, 2001 9:40 AM
To: [EMAIL PROTECTED]
Subject: Re: What is a WIC card? [7:9764]
Wan Interface Card & VWIC's are Voice Wan Interface Cards. It's kin
Anyone keep getting mail from ***@sexyfun.net ?
I noticed that they sent [EMAIL PROTECTED]
an e-mail the other day and now they are being directed to my inbox?
Bob Perez
EPX Network Support
302-326-0700 x4242
Cell 302-420-6883
Message Posted at:
http://www.groupstudy.com/form
22 matches
Mail list logo