Sorry to waste b/w, but couldn't resist:
Layer 8, Religion, would be my guess.
Mark
-Original Message-
From: Howard C. Berkowitz [SMTP:[EMAIL PROTECTED]]
Sent: Wednesday, September 12, 2001 9:43 AM
To: [EMAIL PROTECTED]
Subject:Re: US Stock [7:19433]
That's the beauty
You're mistaken. It's not arrogance, which is the domain of bullies until
they are dethroned. It is PRIDE, which we have had for over 200 years, and
will continue to have for hundreds of years in the future. If it was
arrogance they sought to take away, they were aiming at the wrong target.
I tried it on a 2610 with 12.2.3, and could set encaps on the sub-interface
to dot1q or sde (secure data exchange).
Mark
-Original Message-
From: Chuck Larrieu [SMTP:[EMAIL PROTECTED]]
Sent: Wednesday, September 12, 2001 6:27 PM
To: [EMAIL PROTECTED]
Subject:RE:
What do you mean? Are you talking physical ports to add to your lab? If so,
all you need are a couple of FXS cards with phones attached. If you want to
get fancy you could have one or 2 FXS and an FXO with a POTS line attached.
Mark
-Original Message-
From: Cisco Lover [SMTP:[EMAIL
Actually, DSU/CSU interfaces can be either DTE or DCE. To connect one of
these to a DB-60 serial interface, you'll need a media converter (well
actually an external CSU/DSU).
Mark
-Original Message-
From: tu do [SMTP:[EMAIL PROTECTED]]
Sent: Thursday, August 30, 2001 12:54 PM
To:
Also, check out:
http://www.cisco.com/warp/public/459/41.shtml
Mark
-Original Message-
From: MADMAN [SMTP:[EMAIL PROTECTED]]
Sent: Thursday, August 30, 2001 2:56 PM
To: [EMAIL PROTECTED]
Subject:Re: BGP memory requirement formula... HELP!!! [7:17888]
It's simpler than
Very odd. I suspect bad simms or m/b. Could also be non-cisco approved mem.
Some had a middle chip on them that seemed to do some sort of key/ID
function. Do you have any other known good (preferably Cisco) simms to try?
I don't believe the pc card slot works for reg IOS. I believe it is part
I recognized it from a test (I'd rather not say which one- even the
paranoid have enemies)
-Original Message-
From: Priscilla Oppenheimer [SMTP:[EMAIL PROTECTED]]
Sent: Tuesday, August 28, 2001 7:26 PM
To: [EMAIL PROTECTED]
Subject:RE: ambiguous command [7:17568]
I think
I went thru it, very worthwhile if you can get in. Last I checked (earlier
this year) there was a long wait for it, comparable to the wait for the lab
itself. You are run through a ccie-level lab over 3 days with a Cisco ccie
who really knows his stuff (at least the one in my session sure
Sorry, that's only one example. The other 2 examples are Microsoft WinOS and
Intel CPUs.
Mark
Through Simplicity you may become a simpleton. Through Complexity you may
become redundant
-Original Message-
From: David L. Blair [SMTP:[EMAIL PROTECTED]]
Sent: Monday, August 27, 2001
I have bought ones at Home Depot or Ace Hardware (can't remember which). I
think they were like #6x3/8. Take one up there and let your fingers do the
walking (that's what I had to do). They weren't an exact match (the ends
were pointy, not flat, for one), but they fit and held. I think they
Well, most of those are pretty self-explanatory, except # 9, which is a
trick question. I know I shouldn't be giving answers, but, what the 'ell:
Do NOT attempt to assemble the rifle using the Swahili manual (section c,
paragraph 4 of the manual requires 2 hours of prayer, which will put you
Try changing the stop bits to 1, which is the default, I believe. The
up/down messages are normal during boot operations on an unused interface.
Mark
-Original Message-
From: Richard Chang [SMTP:[EMAIL PROTECTED]]
Sent: Wednesday, August 22, 2001 12:58 AM
To: [EMAIL PROTECTED]
Have you tried moving things around to see if the problem follows any piece
of equipment? Maybe a bad cable, bad port on hub, or speed/duplex mismatch.
Have you tried rebooting router after adding hub? Do you lose link lights
on the hub (and if so, is it just where the router plugs in, or on
As far as WAN goes, anything above DS3 is typically fiber (or wireless in
some cases). Copper CAN support much higher speeds (at least in a LAN
environment), including GigE (and, I wouldn't be surprised, 10GigE when it
comes out). DS3 is coax (copper) or fiber.
Mark
-Original
Sounds to me like he may have config'd NAT to forward all traffic to his web
server.
Mark
-Original Message-
From: Brian [SMTP:[EMAIL PROTECTED]]
Sent: Monday, August 13, 2001 1:46 AM
To: [EMAIL PROTECTED]
Subject:Re: Friday Follies - IP NAT behaviour [7:15822]
why he
Sounds like a 1 port enet card to me. You have a choice of running either
the aui port or the rj-45 port, but not both. I believe you can select
between by using the media-type command on the interface.
Mark
-Original Message-
From: Vik [SMTP:[EMAIL PROTECTED]]
Sent: Monday,
Actually, if he's trying to do NAT with only one interface, it won't work.
You must have an inside (non-translated, usually private address range) and
an outside (translated, usually Internet-routable) interface. At least one
of each. What addresses you translate them into is irrelevant and
You may not always have a tool available to calculate for you. I've been
in several customer meetings where I was required to come up with network
diagrams, including subnet masks, ad hoc. If I had needed to have them wait
til I could power up my laptop, then use a program to do the work, it
As an FYI, NAT takes up about 160 bytes per translation. Check out this link
for more info.
http://www.cisco.com/warp/customer/cc/pd/iosw/ioft/iofwft/prodlit/iosnt_qp.htm
Thanx,
Mark Baker
CCNP looking for a job
-Original Message-
From: Patrick Ramsey [SMTP:[EMAIL PROTECTED]]
Sent:
If I remember correctly, the formula was:
packets in queue=(packets_in/second - packets_out/sec)*number_of_secs.
So if you have a line that can take 25 packets/sec and you're trying to feed
it 50 packets/sec for 10 seconds, it would be:
(50pps-25pps)*10=250packets in queue over 10 seconds.
Leo,
If I understand you correctly, you want to do a manual binding, giving one
particular DHCP client the same address all the time? If so, go here and
take a look at the config:
http://www.cisco.com/univercd/cc/td/doc/product/software/ios120/120newft
/120t/120t1/easyip2.htm#xtocid432218
If I remember correctly, the formula was:
packets in queue=(packets_in/second - packets_out/sec)*number_of_secs.
So if you have a line that can take 25 packets/sec and you're trying to feed
it 50 packets/sec for 10 seconds, it would be:
(50pps-25pps)*10=250packets in queue over 10 seconds.
23 matches
Mail list logo
