networks (0.0.0.0/8
to 127.0.0.0/8).
Same with the 128.0.0.0/2 - that means make sure the first two bits are 10,
but then ignore everything else. So this includes all class B addresses -
from 128.0.0.0 to 191.255.255.255.
Rob.
""Rob Webber"" wrote in message
[EMAIL PROTECTED]&qu
I believe this will do what you are looking for. I did a little testing and
it seemed to work well:
ip prefix-list classful seq 5 permit 0.0.0.0/1 ge 8 le 8
ip prefix-list classful seq 10 permit 128.0.0.0/2 ge 16 le 16
ip prefix-list classful seq 15 permit 192.0.0.0/3 ge 24 le 24
Hope that helps
Alec,
This is quite an interesting scenario you ran into. I think I can explain
what happened.
As you mentioned Cisco enables proxy-arp by default. Usually this is a good
thing - in this case it was the cause of the problems.
Before the change when a 10.67.7.* DHCP client wanted to connect to a
For step 3, it depends whether the link between core 1 and core 2 is a
routed link or a trunk (ISL or 802.1Q) link. If its a routed link (such as
VLAN 3, with all VLANs running OSPF), core 1 will route the packet to core 2
and core 2 will route the packet to client 2.
For step 4, client 2 will no
As far as getting the PIX to prompt for authentication, it can be done,
however it needs to be done by a browser (since the browser has the ability
to "pop up" a username/password box, but Citrix doesn't have this
capability). You can simply have them go to a static web page that you
create which
I haven't seen the lab, either, but how did you perform the filtering of
AS65000? When I read your post I was thinking of the neighbor
remove-private-as command. That should allow R3's loopback network to
propagate, just that R1 won't see the 65000 AS. Feel free to post your
configs and anything e
If I understand your topology correctly, switches 3 and 4 share an Ethernet
segment. If I remember Spanning Tree correctly, one of these two will be the
"designated bridge" for that segment. That bridge will be forwarding packets
toward the root. All other bridges on that segment (in this case, th
I see your point on security, but I don't completely agree. Your current
Frame Relay network is only as secure as your carrier. If someone at your
carrier maps a PVC between you and company X, real traffic can flow
(assuming your router picks it up and places on the physical interface,
which it li
Oops - apparently the link did not come through for some reason. It is:
www.netmasterclass.net/nmc/
Rob.
""Will K."" wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> Does anyone know where information about this class can be found? Thanks.
Message Posted at:
http://www.group
Now called "RS-NMC-1 (Routing and Switching Net Master Class)"
Rob.
""Will K."" wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> Does anyone know where information about this class can be found? Thanks.
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=36513&t=
I agree that this configuration - with HSRP and tracking - could work well
for connections that are initiaed outbound. You would not necessarily need
BGP. R1 could do an outbound NAT to whatever IP address space had been
assigned by ISP 1. R2 could do an outbound NAT to whatever IP address space
h
I am not completely sure, but I do not believe these two cards will
interoperate. The PA-POS is a packet-over-Sonet module. Thus that box will
look to frame the layer 2 frames as POS frames - and it will use the entire
OC-3 for the one POS connection. The PA-A3 is an ATM module. It is looking
to f
For the outbound connectivity, use the HSRP track feature. That "watches" an
interface (the WAN link to your ISP). If that interface goes down, the HSRP
priority of that router gets reduced, making the other router (with the good
ISP link) the HSRP primary. HSRP will make it so no changes are requ
You will need to connect to the console of the IDS. Log in as netrangr
(note: NO "e" in netrangr). Default Passord: "attack" Then enter:
#sysconfig-sensor
You will see a menu:
1 - IP Address
2 - IP Netmask
3 - IP Host Name
4 - Default Route
5 - Network Access Control
6 - Communications In
Try configuring "speed 9600" under the line aux 0. I do not believe you can
use a straight cable, I thiink it has to be rolled.
Also, are you sure port 2065 is the right port number? It sounds high, but
that may be correct...
Rob.
""Joaquim Lopes"" wrote in message
[EMAIL PROTECTED]">news:[EMA
15 matches
Mail list logo