Hi there,
Have anyone out there configured the above with any of your customers or
clients??
I have this scenario over here, and need some advise.
vrf1 | | vrf2
S1/0 || S1/1
---
|Cisco 7206 |
--
4 (68) and dest port = 0x0043
>(67). Yup, that's DHCP alright.
>
>Where is the tcpdumb station attached? Which VLAN? It will see all the
>broadcasts for devices in its VLAN. The switch forwards them. This is
>normal...
>
>Priscilla
>
>At 05:16 AM 2/1/02, Tay Chee
Hi all,
Just like to enquire some issue regarding Catalyst 2924
I have a pretty old Catalyst 2924 (C2900XL-H-M) switch in my office running
IOS Version 11.2(8)SA3, however, it seems that the switch is constantly
sending out broadcast messages as captured by tcpdump.
17:14:51.053952 0:10:b:3c:
Hi,
Someone has any idea which CatOS for Cat6k is a stable release? I am
currently using Release 6.1(1d), and I need to upgrade it. I am also
looking at Release 7.1(1) with SSH support. Any advise from the experts out
there??
Thanks
Regards,
Cheeyong
At 08:48 AM 1/30/02 -0500, Hire, Ejay wr
Hi all,
Hope to seek some advise on the interoperability of G.703 & V.35.
The scenario is as follows :
Cisco 7500 - PSTN - DSU/CSU
Cisco 7206
(G.703) (G.703)(V.35)
It seems that when I have the above setup,
Hi all,
I have a scenario here that I am using a Cisco 7206 with Serial Interface
(V.35), and my customer is using a Cisco 7500 series router with G.703
interface on their router. I am using a ASM40 RAD modem on my end, clocked
to 2Mbps, converting from G.703 to V.35 and terminating on the ser
Hi Ramesh,
When the VPN is established, the originating host will encrypt the packet
with a key, and send across the internet via a virtual tunnel. When the
destination receive the packet, the VPN box will decrypt the packet with
the same key.
If you are connecting to the destination private
Hi all,
May I know how can I obtain the serial number for the NPE for Cisco 7206??
The "show c7200" command says that its displaying the CPU EEPROM serial
number. Is it also referring to the serial number of the NPE?
Please advise.
Regards,
Cheeyong
Message Posted at:
http://www.groupstud
Hi all,
Do you guys have any good recommendation of any Cisco
Conference/Seminar/Course conducted by Cisco other than Networkers? Please
recommend. Thanks.
Regards,
Cheeyong
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=26087&t=26087
-
Hi,
May I know why is it that whenever we do a traceroute to a destination, the
last hop will sometimes have a "!X" instead of the TTL value returned?
Sometimes it will also have an "*" at the last TTL value, why is this so??
Is there any document on the net that explains the above mentioned i
Hi all,
Just a stupid question. Can I combine 2 serial interfaces using
Etherchannel?? Is there such a feature on any Cisco routers?? Please
advise. Thanks.
Regards,
Cheeyong
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=16517&t=16517
Hi all,
Would appreciate if someone could point out some good sites for read up on
BGP Communities. I had read through some on the CCO website, but it seems
quite confusing.
Regards,
Cheeyong
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=16362&t=16362
---
Hi,
I am running BGP in my network, however, I do not understand the
implications of advertising default route to my peer. How will this action
affect my network? My Manager forbids me to advertise default route to our
peer. Can someone please advise? Thanks.
Regards,
Cheeyong
Message Pos
Hi all,
I am currently plotting MRTG on a Catalyst 6509 switch. But I am unable to
decipher the target code in the config file.
Target[192.168.10.254.XYZ]: 1:[EMAIL PROTECTED]
I am unable to determine which interface is XYZ referring to, as there is
no proper numbering for XYZ. There are numb
>[EMAIL PROTECTED]
>020 8509 2990
>07785 362626
>www.pioneer-computers.com
>London UK
>
>
>"Tay Chee Yong" wrote in message
>[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> > Hi all,
> >
> > I would like to perform load sharing 2 seri
Hi Remmert,
Thank you for your advise. Below is the updated network diagram.
(10.10.10.1/24)
| E0
-
| Cisco 2501 R1 |
---
Hi all,
I would like to perform load sharing 2 serial links on a Cisco 2501, how
should I go about doing that?? I had thought of using HSRP, but I think it
is not applicable in this scenario. Any advise?? Below is the network
diagram.
(10.10.10.1/24)
Hi all,
I am currently configuring 2 protected ports on a Catalyst 2924 to allow
them to talk to each other with the help of a Cisco router. My
understanding of the protected port on the catalyst switch is that, host on
a protected port is not able to communication with another host on another
; On Mon, 21 May 2001, Tay Chee Yong wrote:
> >
> > > Hi all,
> > >
> > > I am suppose to accept the following routes from my peer AS123, which
> has
> > > peering with another AS (AS456). I was told to accept the following
> routes
> > >
Hi all,
I am suppose to accept the following routes from my peer AS123, which has
peering with another AS (AS456). I was told to accept the following routes
from them, but I don't really understand the regular expression. Can anyone
please help to explain to me the following? And what does the
Hi Swapnil,
Yes! That's what MRTG is doing it will update the graph every 5
minutes, using a cron.
Regards,
Cheeyong
At 08:26 AM 5/16/01 +0530, [EMAIL PROTECTED] wrote:
>Is there any option in MRTG where I can get only the operational status
>and show it up on some graph which refreshes e
Hi,
You might want to try MRTG.
http://www.mrtg.org
Regards,
Cheeyong
At 10:45 PM 5/15/01 -0400, [EMAIL PROTECTED] wrote:
>Dear All
>
>I have a bit of a problem.
>I have to monitor one frame-relay n/w.
>It is having hub & spoke topology. Now my problem is i only have IP
>connectivity to the hub
Hi all,
I have a Cat6509 here in my lab, and had been playing with the QoS for a
while - not really in depth though. I would like to apply per port type of
QoS whereby the ingress and egress traffic on that port will comply to the
QoS specified. I had tried posting a similar question to the Ci
Hi all,
Does anyone has any recommendations or websites that has good CCNP exam
materials? If so, I would appreciate if someone could guide me to where I
can get the materials. I would like to start with CIT exam first. Any good
recommendations for materials related with CIT exams? Please advi
Hi all,
I had just completed my CCNA, and would like to move on to take CCNP. Any
idea what are the materials which I would need, and also what areas will I
be tested on?? Advise will be greatly appreciated.
Regards,
Cheeyong
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i
Hi all,
I had just completed my CCNA, and would like to move on to take CCNP. Any
idea what are the materials which I would need, and also what areas will I
be tested on?? Advise will be greatly appreciated.
Regards,
Cheeyong
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i
26 matches
Mail list logo