Gentlemen:
I would appreciate it if someone could help me with a simple config for ISDN
so I could dial-in on a 1750 router.
Thank you in advance for your help.
Regards,
John Huston
[EMAIL PROTECTED]
_
FAQ, list archives, and subscription info: http://www.gr
Dear all,
When setup ISDN dial in, is it necessary that we need to assign User ID
and password. Suppose it only support sigle channel BRI.
Rgds,HC
___
UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html
FAQ, list archives, and subscription info
If i do a sh isdn status and get the following:The
current ISDN Switchtype = basic-ni1
ISDN BRI0 interface
Layer 1 Status:
ACTIVE
Layer 2 Status:
TEI = 96, State = MULTIPLE_FRAME_ESTABLISHED
TEI = 97, State = MULTIPLE_FRAME_ESTABLISHED
Spid Status:
TEI 9
http://www.cisco.com/warp/public/129/index.shtml
Lots of examples.
> -Original Message-
> From: John Huston [mailto:[EMAIL PROTECTED]]
> Sent: Tuesday, March 27, 2001 10:31 AM
> To: [EMAIL PROTECTED]
> Subject: ISDN - Dial-IN
>
>
> Gentlemen:
>
> I
: ISDN - Dial-IN
Gentlemen:
I would appreciate it if someone could help me with a simple config for ISDN
so I could dial-in on a 1750 router.
Thank you in advance for your help.
Regards,
John Huston
[EMAIL PROTECTED]
_
FAQ, list archives, and subscription info
ISDN Dial-IN
Dear all,
When setup ISDN dial in, is it necessary that we need to assign User ID
and password. Suppose it only support sigle channel BRI.
Rgds,HC
___
UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html
FAQ, list archives
11:26
> To: [EMAIL PROTECTED]
> Subject: ISDN Dial-IN
>
> Dear all,
>
> When setup ISDN dial in, is it necessary that we need to assign User ID
> and password. Suppose it only support sigle channel BRI.
> Rgds,HC
>
> ___
> UPDATED
me and password if you are using pap or chap
> > authentication. If you don't use any authentication then no password or
> > username is required.
> >
> > -Original Message-
> > From: harold chan [mailto:[EMAIL PROTECTED]]
> > Sent: 18 July 2000 11:26
>
Hello Beth,
Looking at your sh isdn status output, i think the problem is at layer 3. I
would suggest that you use the deb ppp neg and deg ppp auth. This should let
you know if authentication is successful and also the ipcp negotiation.
Also, you can use the deb isdn q931, this does give a lot of
I am trying to set a router with ISDN BRI to answer calls originated from a
PC using ISDN line,
Here is my configuration, but it seems not working, any suggestions?
interface BRI0/0
ip unnumbered Loopback1
encapsulation ppp
dialer idle-timeout 7200
isdn switch-type basic-net3
Did you define interesting traffic?
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=44046&t=44013
--
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violation
I have a Cisco7507 T1 Pri card directly connected to a private PBX, I can
dial-out of this 7507 successfully but calls to it from the outside never
get past the PBX. I'm not sure if the problem is with the router or the
pbx, my isdn service state shows 'out of service' but the interface, t1
contr
one more rookie question :)
is there a way to add a pause on my dialer map
statement between the pic code and the number?
thanks!
> From: "beth shriver" <[EMAIL PROTECTED]>
> To: <[EMAIL PROTECTED]>
> Sent: Saturday, January 13, 2001 11:27 AM
> Subject: troublesh
No i have primary ISDN on center. I want to use it just for dial-in. And the
dial-in user use his ip address, that not using ip pool; and don't
authentication.
Even it can dial up, but cannot ping each other. I open the debug of dialer
Can you give me a sample?
Must it have 'dialer-gourp' command
14 matches
Mail list logo
